Documentos de Académico
Documentos de Profesional
Documentos de Cultura
This equipment has been tes ted and found to comply with the limits of a Class
B digital devic e, purs uant to Part 15 of the FCC Rules . T hese limits are designed
to provide reasonable protec tion against harmful interference in a residential
installation. T his equipment generates , uses and can radiate radio frequency
energy and, if not ins talled and used in accordance with the instructions , may
cause harmful interference to radio communications . There is no guarantee
that interference will not occur in a particular ins tallation.
The content of this user’s manual is subject to be c hanged without notice and
we will not be res ponsible for any mis takes found in this user’s manual. All the
brand and produc t names are trademarks of their respec tive companies .
Table of Contents
CHAPTER 1: INTRODUCTION
1.1 BEFORE YOU ST ART
Thank you for choosing our product. Be fore you start installing the
mothe rboard, please make sure you follow the instructions be low:
Prepare a dry and stable work ing environment with
sufficie nt lighting.
Always disconne ct the compute r from powe r outle t
be fore ope ration.
Before you take the mothe rboard out from anti-static
bag, ground yourse lf prope rly by touching any safe ly
grounde d appliance, or use grounded wrist strap to
remove the static charge.
Avoid touching the compone nts on mothe rboard or the
rear side of the board unless ne cessary. Hold the board
on the edge , do not try to be nd or flex the board.
Do not leave any unfastene d small parts inside the
case afte r installation. Loose parts will cause short
circuits which may damage the equipment.
Keep the compute r from dange rous a rea, such as hea t
source , humid air and wate r.
3
Motherboard Manual
1.3 MOT HERBOARD FEAT URES
SPEC
LGA 775
/ Celeron D processor up to 3.8 GHz Supports Hy per -Thre ading Technology / Execute
CPU Supports Intel Core2Duo pr ocessor Disable Bit/ Enhanced Intel S peedStep® / Intel
DIMM Slots x 2
Chassis open hea der(o ptional) x1 For chassis intruder detection function
Board Size 201 mm (W) x 244 mm (L) Micro ATX form Factor
Special
RAID 0 / 1 support
Features
Line Out
M ic In 1/
Ba ss/ C ente r
5
Motherboard Manual
1.5 MOT HERBOARD LAYOUT
JATXPWR1
JKBMS1
JCFAN1
JATXPWR2
LGA775
JCOM1
CPU1
JP RNT1
JVGA1
DDR2_A2
DDR2_A1
JUSB1
JUSBV1
P4M800 Pro
IDE1
IDE2
JUSBLAN1
Super
I/O
JAUDIO1
BIOS AGP1
LAN BAT1
PCI1
JUSB2
PCI3
JCMOS1
JSFAN1 JPANEL1 JCI1(opt ion al)
Codec
CNR1 FDD1
I R (opt ional)
6
P4M800 Pro-M7
Special Notice:
Remove Pin Cap before installation, and make good preservation
for future use. When the CPU is removed, cover the Pin Cap on the
empty socket to ensure pin legs won’t be damaged.
Pin Cap
Step 1: Pull the socket locking lever out from the socket and then raise
the lever up to a 90-degree angle.
7
Motherboard Manual
Step 2: Look for the triangular cut edge on socket, and the golden dot on
CPU should point forwards this triangular cut edge. The CPU will
fit only in the correct orientation.
Step 2-1:
Step 2-2:
Step 3: Hold the CPU down firmly, and then lower the lever to locked
position to complete the installation.
Step 4: Put the CPU Fan and heatsink assembly on the CPU and buckle it
on the retention frame. Connect the CPU FAN power cable into
the JCFAN1. This completes the installation.
8
P4M800 Pro-M7
1 Pin Assignment
1 Ground
J CFAN1
2 +12V
3 FAN RPM rate
sense
4 Smart Fan
Control
Pin Assignment
1 Ground
2 +12V
3 FAN RPM rate
JSFAN1 sense
3 1
Note:
The JSFAN1 s upport 3-pi n head connec tor. When c onnecti ng with wires onto connec tors,
pleas e note that the red wire is the positi ve and s hould be c onnected to pin#2, and the
blac k wire is Ground and s hould be c onnected to GND.
9
Motherboard Manual
2.3 INST ALLING SYST EM MEMORY
A. Memory Modules
DDR2_A1
DDR2_A2
1. Unlock a DIMM slot by pressing the retaining clips outward. Align a
DIMM on the slot such that the notch on the DIMM matches the
break on the Slot.
2. Insert the DIMM vertically and firmly into the slot until the retaining
chip snap back in place and the DIMM is properly seated.
B. Memory Capacity
DIMM Socket DDR Module Total Memory Size
Location
DDR2_A1 256MB/512MB/1GB
Max is 2GB.
DDR2_A2 256MB/512MB/1GB
10
P4M800 Pro-M7
2.4 CONNECT ORS AND SLOT S
FDD1: Floppy Disk Conne ctor
The motherboard prov ides a standard floppy disk connector that supports 360K,
720K, 1.2M, 1.44M and 2.88M floppy disk ty pes. This connector supports the
prov ided f loppy drive ribbon cables.
2 34
1 33
40 39
2 1
IDE1 IDE2
11
Motherboard Manual
PCI1~PCI3: Pe riphe ral Component Interconne ct Slots
This motherboard is equipped with 3 standard PCI slots. PCI stands f or
Peripheral Component Interconnect, and it is a bus standard for expansion
cards. This PCI slot is designated as 32 bits.
PCI1
PCI2
PCI3
AGP1
CNR1
12
P4M800 Pro-M7
PWR_LED
SLP On/Off
++-
2 24
1 23
+ -
SPK RST IR (optional)
HLED
13
Motherboard Manual
JATXPWR1: ATX Powe r Source Conne ctor
This connector allows user to connect 20-pin power connector on the ATX
power supply.
10 20
1 11
Pin Assignment
3 4 1 +12V
2 +12V
3 Ground
4 Ground
14
P4M800 Pro-M7
JUSB2/JUSB3: He ade rs for USB 2.0 Ports at Front Panel
This header allows user to connect additional USB cable on the PC f ront panel,
and also can be connected with internal USB devices, like USB card reader.
Pin Assignment
1 +5V (fused)
2 +5V (fused)
3 USB-
4 USB-
5 USB+
6 USB+
7 Ground
8 Ground
2 10 JUSB2 9 Key
10 NC
1 9 JUSB3
3
1 3
1
3
Pin 1-2 close (Default)
1
JUSBV1
3
1 3
1
1 3
Pin 2-3 close
JUSBV2
Note:
In order to s upport this function “Power-On s ystem vi a USB devic e,” “JUSBV1/ JUSBV2”
jumper cap should be plac ed on Pin 2-3 indi viduall y.
15
Motherboard Manual
JFAUDIO1: Front Panel Audio Heade r
This header allows user to connect the front audio output cable with the PC f ront
panel. It will disable the output on back panel audio connectors.
Pin Assignment
1 Mic-in/Stereo MIC-in
R
2 Ground
3 Stereo MIC-in L
4 Audio power
5 Right line-out/
Speaker-out Right
6 Right line-out/
Speaker-out Right
7 Reserved
2 14 8 Key
9 Left line-out/
Speaker-out Left
1 13 10 Left line-out/
Speaker-out Left
11 Right line-in (optional)
12 Right line-in (optional)
13 Left line-in (optional)
14 Left line-in (optional)
Pin Assignment
1 Left Channel Input
2 Ground
3 Ground
4 Right Channel Input
4 1
16
P4M800 Pro-M7
JCMO S1: Cle ar CMOS Heade r
By placing the jumper on pin2-3, it allows user to restore the BIOS saf e setting
and the CMOS data, please carefully f ollow the procedures to avoid damaging
the motherboard.
1 3
1 3
Pin Assignment
1 Ground
2 T X+
3 T X-
4 Ground
5 RX-
JSATA2 6 RX+
7 Ground
7 4 1
JSATA1
17
Motherboard Manual
JSPDIFO1: Digital Audio-out Conne ctor
This connector allows user to connect the PCI bracket SPDIF output header.
Pin Assignment
1 +5V
2 SPDIF_OUT
3 Ground
3 1
Pin Assignment
1 Case open signal
2 Ground
1 2
18
P4M800 Pro-M7
Block 1 Block 2
Block 3 Bl ock 4
Block 5 Bl ock 6
19
Motherboard Manual
RAID 1:
Every read and write is actually carried out in parallel across 2 disk drives in a RAID 1
array system. The mirrored (backup) copy of the data can reside on the same disk or on
a second redundant drive in the array. RAID 1 provides a hot-standby copy of data if
the active volume or drive is corrupted or becomes unavailable because of a hardware
failure.
RAID techniques can be applied for high-availability solutions, or as a form of
automatic backup that eliminates tedious manual backups to more expensive and less
reliable media.
Features and Benefits
Drives: Minimum 2, and maximum is 2.
Uses: RAID 1 is ideal for small databases or any other application that
requires f ault tolerance and minimal capacity.
Benefits: Prov ides 100% data redundancy. Should one driv e f ail, the
controller switches to the other drive.
Drawbacks: Requires 2 driv es for the storage space of one driv e.
Perf ormance is impaired during driv e rebuilds.
Fault Tolerance: Yes.
Block 1 Block 1
Block 2 Block 2
Block 3 Block 3
20
P4M800 Pro-M7
You will see the following window after you insert the CD
The setup guide will auto detect your motherboard and operating system.
Note:
If this window didn’t show up after you ins ert the Driver CD, please use file brows er to
locate and execute the file SETUP.EXE under your optical drive.
A. Driver Installation
To install the driver, please click on the Driver icon. The setup guide will
list the compatible driver for your motherboard and operating system.
Click on each device driver to launch the installation program.
B. Software Installation
To install the software, please click on the Software icon. The setup guide
will list the software available for your system, click on each software title
to launch the installation program.
C. Manual
Aside from the paperback manual, we also provide manual in the Driver
CD. Click on the Manual icon to browse for available manual.
Note:
You will need Acrobat R eader to open the manual file. Pleas e download the latest version
of Acrobat Reader software from
http://www.adobe.com/products/acrobat/readstep 2.html
21
Motherboard Manual
5.2 AWARD BIOS BEEP CODE
Beep Sound Meaning
One long beep followed by two shortVideo card not found or v ideo card
beeps memory bad
High-low siren sound CPU overheated
System will shut down automatically
One Short beep when system boot-up No error found during POST
Long beeps every other second No DRAM detected or install
In this Case, please follow the procedure below to restore the BIOS:
1. Make a bootable floppy disk.
2. Download the Flash Utility “AWDFLASH.exe” from the Biostar
website: www.biostar.com.tw
3. Confirm motherboard model and download the respectively BIOS
from Biostar website.
4. Copy “AWDFLASH.exe” and respectively BIOS into floppy disk.
5. Insert the bootable disk into floppy drive and press Enter.
6. System will boot-up to DOS prompt.
7. Type “Awdflash xxxx.bf/sn/py/r” in DOS prompt.
(xxxx means BIOS name.)
8. System will update BIOS automatically and restart.
9. The BIOS has been recovered and will work properly.
22
P4M800 Pro-M7
B. CPU Overheated
If the system shutdown automatically after power on system for
seconds, that means the CPU protection function has been activated.
After confirmed, please follow steps below to relief the CPU protection
function.
1. Remove the power cord from power supply for seconds.
2. Wait for seconds.
3. Plug in the power cord and boot up the system.
Or you can:
1. Clear the CMOS data.
(See “Close CMOS Header: JCMOS1” section)
2. Wait for seconds.
3. Power on the system again.
23
Motherboard Manual
5.4 TROUBLESHOOT ING
Probable Solution
1. No power to the system at all 1. Make sure power cable is
Power light don’t illuminate, f an securely plugged in.
inside power supply does not turn 2. Replace cable.
on. 3. Contact technical support.
2. Indicator light on key board does
not turn on.
System inoperativ e. Keyboard lights Using even pressure on both ends of
are on, power indicator lights are lit, the DIMM, press down firmly until the
and hard driv e is spinning. module snaps into place.
System does not boot from hard disk 1.Check cable running from disk to
driv e, can be booted f rom optical driv e. disk controller board. Make sure
both ends are securely plugged
in; check the driv e type in the
standard CMOS setup.
2. Backing up the hard drive is
extremely important. All hard
disks are capable of breaking
down at any time.
System only boots f rom optical driv e. 1. Back up data and applications
Hard disk can be read and applications f iles.
can be used but booting from hard disk 2. Ref ormat the hard driv e.
is impossible. Re-install applications and data
using backup disks.
Screen message says “Invalid Rev iew system’s equipment. Make sure
Conf iguration” or “CMOS Failure.” correct inf ormation is in setup.
Cannot boot system after installing 1. Set master/slave jumpers
second hard driv e. correctly.
2. Run SETUP program and select
correct driv e types. Call the drive
manuf acturers f or compatibility
with other drives.
24
P4M800 Pro-M7
CHAPTER 6: WARPSPEEDER™
25
Motherboard Manual
2. When you see the following dialog in setup procedure, it means setup
is completed. If the “Launch the WarpSpeeder Tray Utility” checkbox
is checked, the Tray Icon utility and [WarpSpeeder™] utility will be
automatically and immediately launched after you click “Finish”
button.
Usage :
The following figures are just only for reference, the screen printed in
this user manual will change according to your motherboard on hand.
26
P4M800 Pro-M7
6.4 WARPSPEEDER™
1. Tray Icon:
Whenever the Tray Icon utility is launched, it will display a little tray
icon on the right side of Windows Taskbar.
27
Motherboard Manual
2. Main Panel
If you click the tray icon, [WarpSpeeder™] utility will be invoked.
Please refer to the following figure; the utility’s first window you will
see is Main Panel.
Main Panel contains fe ature s as follows:
a. Display the CPU Speed, CPU external clock, Memory clock, AGP clock,
and PCI clock information.
b. Contains About, Voltage, Overclock, and Hardware Monitor Buttons for
invoking respective panels.
c. With a user-friendly Status Animation, it can represent 3 overclock
percentage stages:
Man walking→overclock percentage from 100% ~ 110 %
Panther running→overclock percentage from 110% ~ 120%
Car racing→overclock percentage from 120% ~ above
28
P4M800 Pro-M7
3. Voltage Panel
Click the Voltage button in Main Panel, the button will be highlighted
and the Voltage Panel will slide out to up as the following figure.
In this panel, you can decide to increase CPU core voltage and
Memory voltage or not. The default setting is “No”. If you want to get
the best performance of overclocking, we recommend you click the
option “Yes”.
29
Motherboard Manual
4. Overclock Panel
Click the Overclock button in Main Panel, the button will be
highlighted and the Overclock Panel will slide out to left as the
following figure.
30
P4M800 Pro-M7
c. “Auto-overclock button”: User can click this button and
[WarpSpeeder™] will set the best and stable performance and
frequency automatically. [WarpSpeeder™] utility will execute a
series of testing until system fail. Then system will do fail-safe
reboot by using Watchdog function. After reboot, the
[WarpSpeeder™] utility will restore to the hardware default
setting or load the verified best and stable frequency according
to the Recovery Dialog’s setting.
d. “Verify button”: User can click this button and [WarpSpeeder™]
will proceed a testing for current frequency. If the testing is ok,
then the current frequency will be saved into system registry. If
the testing fail, system will do a fail-safe rebooting. After reboot,
the [WarpSpeeder™] utility will restore to the hardware default
setting or load the verified best and stable frequency according
to the Recovery Dialog’s setting.
Note:
Because the testing programs, invoked in Auto-overclock and Verify,
include DirectDraw, Direct3D and DirectShow tests, the DirectX 8.1 or
newer runtime library is required. And please make sure y our display
card’s color depth is High color (16 bit) or True color( 24/32 bit ) that is
required f or Direct3D rendering.
31
Motherboard Manual
6. About Panel
Click the “about” button in Main Panel, the button will be highlighted
and the About Panel will slide out to up as the following figure.
In this panel, you can get model name and detail information in hints
of all the chipset that are related to overclocking. You can also get
the mainboard’s BIOS model and the Version number of
[WarpSpeeder™] utility.
Note :
Because the overclock, overvoltage, and hardware monitor features
are controlled by several separate chipset, [WarpSpeeder™] divide
these features to separate panels. If one chipset is not on board, the
correlative button in Main panel will be disabled, but will not interfere
other panels’ functions. This property can make [WarpSpeeder™]
utility more robust.
32
P4M800 Pro-M7
33
Motherboard Manual
LGA 775
CPU Intel Core2Duo Prozessoren ( nur für / Enha nced I ntel Spee dStep® / Exte nde d
consumption.
Grafik Integrierter UniC hrome Pro C hipsatz Max. 64MB gemeinsam benutzter Videospeicher
DDR2 DIMM-Steckplätze x 2
Audio-Code 6-Kanal-Audioausgabe
ALC 655
c AC’97 Version 2.3
AGP-Steckplatz x1
Steckplätze CNR-Steckplatz x1
PCI-Steckplatz x3
34
P4M800 Pro-M7
Spezifikationen
Unterstützt die
Front-Audioa nschluss x1
Fronttafel-Audioanschlussfunktio n
"CMOS löschen"-Sockel x1
Fronttafel-USB-Anschlüsse
Stromanschluss (4-poli g) x1
PS/2-Tastatur x1
PS/2-Maus x1
Serieller Anschluss x1
Rückseiten- Druckeranschluss x1
E/A VGA-Anschluss x1
LAN-Anschluss x1
USB-Anschluss x4
Audioanschluss x3
Platinengr ö
201 mm (B) X 244 mm (L)
ße.
Sonderfunkt
Unterstützt RAID 0 / 1
ionen
Biostar behält sich das Recht v or, ohne
OS-Unterst
Windows 2K / XP Ankündigung die Unterstützung für ei n
ützung
Betriebssystem hinzuzufügen oder zu entferne n.
35
Motherboard Manual
FRANCE
SPEC
LGA 775
Processeurs Intel Penti um 4 / Pentium
Prend en charge les technologies
D / C eleron D jusqu'à 3,8 GHz
Hyper -Thre ading / d'ex écution de bit de
UC Processeurs Intel Core 2Duo
désactivation / I ntel Spe edStep® optimisée / de
(Seulement pour Ver 2.0 / 8.0)
mémoire étendue 64
*It is recommende d to use processors
with 95W power consumption.
Bus frontal 533 / 800 / 1066 MHz
VIA P4M800 PRO
Chipset
VIA VT8237R+
Graphi que Integré dans l a chipset U niChrome
Mémoire vidé o partagée maximale de 64 Mo
s Pro
ITE IT8705AF Initiatives de co ntrôle e nvironnementales,
Fournit la fo nctionnalité de Super E/S Moniteur de matériel
Super E/S
patrimoniales la plus utilisée. Contrôleur de vitesse de ventilateur
Interface à faible compte de broc hes Fonction " Gardie n i ntelligent" de l'ITE
Fentes DDR 2 DIMM x 2
Prend en charge la DDR 2 400 / 533 Module de mém oire DDR2 à mo de à simple v oie
Mémoire
Chaque DIMM prend e n charge des Les DIMM à r egistres et DIMM avec code
principale
DDR2 de 256 M o / 512 Mo / 1Go correcteurs d'erreurs so nt pas prises en charge
Capacité mémoire maximale de 2 Go
Prend en charge le mode PIO 0~4,
IDE Contrôleur IDE intégr é Mode pri ncipale de Bus Ultra DMA 33 / 66 / 100 /
133
Conforme à la spécification SATA Version 1.0
SATA Contrôleur Serial ATA intégré :
Taux de transfert jusqu'à 1.5 Go/s.
10 / 100 Mb/s négociation a utomatique
LAN PHY Realtek RTL8201BL/RTL8201CL
Half / Full duplex capability
Codec Sortie audio à 6 voies
ALC 655
audio AC’97 Version 2.3
Fente AGP x1
Fentes Fente CNR x1
Fente PCI x3
Connecteu Chaque connector pre nd en charge 2 lecteurs de
Connecteur de disquette x1
r disquettes
embarqué Chaque connecteur prend e n char ge 2
Connecteur IDE x2
périphéri ques I DE
Chaque connecteur prend e n char ge 1
Connecteur SATA x2
périphéri que SATA
36
P4M800 Pro-M7
SPEC
Fonctionna
lités Prise en c harge RAID 0 / 1
spéciales
Support Biostar se réserve le droit d'ajo uter o u de
Windows 2K / XP
SE supprimer le support de SE av ec ou sans préavis.
37
Motherboard Manual
IT ALIAN
SPECIFICA
LGA 775
CPU Processore Intel Core 2Duo (solo per Bit / Enhance d I ntel Spee dStep® / Tecnologi a
Grafica Integrata nel Chi pset UniC hrome Pr o La memoria vi deo co ndivisa massima è di 64MB
IDE Controller IDE i ntegrato Modalità Bus Master Ultra DMA 33 / 66 / 100 /
133
Alloggio AGP x1
Alloggi Alloggio CNR x1
Alloggio PCI x3
38
P4M800 Pro-M7
SPECIFICA
Connettore alimentazione x1
(20 pin)
Connettore alimentazione x1
(4 pi n)
Tastiera PS/2 x1
Mouse PS/2 x1
Porta seriale x1
I/O
Porta stampante x1
pannello
Porta VGA x1
posteriore
Porta LAN x1
Porta USB x4
Connettore audio x3
i scheda (altezza)
Caratterist
speciali
Sistemi Biostar si riserva il diritto di aggiungere o
39
Motherboard Manual
SPANISH
Especificación
LGA 775
Procesador I ntel Pe ntium 4 / P entium
D / C eleron D hasta 3,8 GHz Admite Hyper -Threadi ng / Bit de deshabilitación
CPU Procesador I ntel Core 2Duo de e jecución / I ntel Spee dStep® Me jorado /
(solamente para Ver 2.0 / 8.0) Tecnolo gía Extended M emory 64
*It is recommende d to use processors
with 95W power consumption.
FSB 533 / 800 / 1066 MHz
Ranura A GP X1
Ranuras Ranura CNR X1
Ranura PCI X3
40
P4M800 Pro-M7
Especificación
Cabecera de ve ntilador de
Fuente de alimentación de ventilador de sistema
sistema X1
Cabecera de chasis abi erto X1
Función de detección de i ntrusos e n el chasis
(opcional)
Conector de alimentación X1
(20 patillas)
Conector de alimentación X1
(4 patillas)
Teclado PS/2 X1
Ratón PS/2 X1
Puerto serie X1
Panel
Puerto de impr esora X1
trasero de
Puerto VGA X1
E/S
Puerto de re d local X1
Puerto USB X4
Conector de sonido X3
Tamaño de
201mm. (A) X 244 Mm. (H)
la placa
Funciones
Admite RAID 0 / 1
especiales
Soporte de
Biostar se reserva el derecho de aña dir o r etirar el
sistema Windows 2K / XP
soporte de cualquier SO con o sin aviso previo.
operativo
41
Motherboard Manual
PORT UGUESE
ESPECIFICAÇÕES
LGA 775
Processador I ntel Pe ntium 4 / Pentium
D / C eleron D até 3,8 GHz Suporta as tecnologias Hyper -Threa ding /
CPU Processador Intel Core2Duo (a penas Execute Disable Bit / Enhanced I ntel SpeedStep®
para os m odelos Ver 2.0 / 8.0) / Exte nded Memory 64
*It is recommende d to use processors
with 95W power consumption.
FSB 533 / 800 / 1066 MHz
Característ
Suporta as funções RAID 0 / 1
icas
especiais
Sistemas
A Biostar reserva-se o direito de adicionar ou
operativos
Windows 2K / XP remover suporte par a qual quer sistema operativo
suportado
com ou sem aviso pré vio.
s
43
Motherboard Manual
POLISH
SPEC
LGA 775
Procesor Intel Pe ntium 4 / Pentium D /
Celeron D do 3,8 GHz Obsługa Hy per-Thre ading / Execute Disabl e Bit /
Procesor Procesor I ntel Core 2Duo (wyłącznie Enha nced Intel SpeedStep® / Extended Memory
dla Ver 2.0 / 8.0) 64 Technology
*It is recommende d to use processors
with 95W power consumption.
FSB 533 / 800 / 1066 MHz
Gniazdo AGP x1
Gniazda Gniazdo CNR x1
Gniazdo PCI x3
44
P4M800 Pro-M7
SPEC
Złącze panela przedniego x1 Obsługa eleme ntów pa nela przedniego
Przednie złącze a udio x1 Obsługa funkcji audio na pa nelu przednim
Złącze wejścia CD x1 Obsługa funkcji wejścia a udio CD
Złącze wyjścia S/PDIF x1 Obsługa funkcji cyfrowe go wy jścia audi o
Wymiary
201 mm (S) X 244 mm (W)
płyty
Funkcje
Obsługa RAID 0 / 1
specjalne
Obsluga
Biostar zastrzega sobie prawo do dawania lub
systemu
Windows 2K / XP odwoływania obsługi dowolnego systemu
operacyjn
operacyjnego bez powiadomie nia.
ego
45
Motherboard Manual
RUSSIAN
СПЕЦ.
LGA 775
CPU Процессор Intel Penti um 4 / P entium
(центра ль D / C eleron D до 3.8 ГГц Подде ржка техноло гий Hy per-Thre ading /
ный Процессор Intel Core 2Duo ( тольк о Execute Disable Bit / Enhanced I ntel SpeedStep®
процессор для Ver 2.0 / 8.0) / Exte nded Memory 64 Technol ogy
) *It is recommende d to use processors
with 95W power consumption.
FSB 533 / 800 / 1066 МГц
Набор
VIA P4M800 PRO
микросхе
VIA VT8237R+
м
Встроенная в набо р м икросхем Максимальная совмес тно используемая видео
Графика
UniChrome Pro память состав ляет 64 МБ
Слоты DDR2 DIMM x 2
Подде ржка DDR2 400 / 533 Модуль памя ти с однока наль ным режим ом
Основная Каждый модуль DIMM DDR2
память поддержива ет 256MB / 512МБ / 1ГБ Не подде рживае т за рег истриров анные моду ли
DDR2 DIMM and ECC DIMM
Максимальная ёмк ость памя ти 2 ГБ
ITE IT8705AF
Обеспечива ет на ибо лее Инициа тивы по охране ок ружающей среды,
используемые дейс твующие Аппара тный монитор
Super I/O функциональные возможности Регуля тор скорости
Super I/O. Функция ITE "Smart Guardian"
Инте рфейс с низким к оличеством (Интелле ктуа льна я защ ита)
выводов
Встроенное устройств о у прав ления Режим "хозя ина " ш ины Ultra DMA 33 / 66 / 100
IDE встрое нными интерфе йсами / 133
устройс тв Подде ржка режима PIO 0~4,
Встроенное последов ате льное скорость передач и данных до 1.5 гигабит/с.
SATA
устройс тво управле ния ATA Соотве тств ие спецификации SATA версия 1.0.
Локаль на Автоматическое сог ласова ние 10 / 100 М б/с
Realtek RTL8201BL/RTL8201CL
я сеть Частич ная / полная дуплексна я способность
Звуково й Шестика наль ный зву ково й выхо д
ALC 655
кодек AC’97 Версия 2.3
Слот A GP x1
Слоты Слот C NR x1
Слот PCI x3
Встроенн Каждый разъём подде рживае т 2 нако пителя на
Разъём НГМД x1
ый разъём гибк их ма гнитных дисках
Каждый разъём по дде рживае т 2 встрое нных
Разъём IDE x2
интерфейса накопителе й
Каждый разъём по дде рживае т 1 устро йство
Разъём SATA x2
SATA
46
P4M800 Pro-M7
СПЕЦ.
Разъём на лицево й пане ли x1 Подде ржка устро йств на лицево й па нели
Подде ржка звук овых функций на лицево й
Входно й звук овой раз ъём x1
пане ли
Разъём вв ода для CD x1 Подде ржка фу нкции вво да для CD
Подде ржка выво да циф рово й звуко вой
Разъём выво да для S/PDIF x1
функции
Контак тирующее приспосо бле ние Источник пита ния для ве нтиля тора
вентиля тора центра льно го центра льно го процессора (с фу нкцией
процессора x1 интелле ктуа льно го вентилято ра)
Контак тирующее приспосо бле ние
Источник пита ния для ве нтиля тора сис темы
вентиля тора системы x1
Шасси о ткрыто го к онтактирую щего
Для фу нкции обнаружения злоумышле нника
прис пособления x1
шасси
(допо лните льно )
Открытое контак тирующее
прис пособление CMOS x1
Каждый разъём по дде рживае т 2 USB-порта на
USB-разъём x2
лицевой панели
Разъем питания ( 20 вывод) x1
Разъем питания ( 4 вывод) x1
Клавиа тура PS/ 2 x1
Мышь PS/2 x1
Задняя Последо вате льный по рт x1
пане ль Порт подключ ения принтера x1
средств Порт VGA x1
ввода-выв Порт LAN x1
ода USB-порт x4
Гнездо для по дключ ения
наушников x3
Размер
201 мм (Ш ) X 244 мм (В)
пане ли
Специаль
ные
техническ
Подде ржка RAID 0 / 1
ие
харак тери
стики
Biostar сохраня ет за собо й прав о добав лять
Подде ржк
Windows 2K / XP или уда лять сре дства обес пече ния для OS с
а OS
или без пре дварительного уведомле ния.
47
Motherboard Manual
ARABIC
اﻟﻤﻮاﺻﻔﺎت
LGA 775
Hyper -Thr eadi ng / Ex ecute Disa ble Bit /ﺕﺪﻋﻢ ﺕﻘﻨﻴﺎت ﺑ ﺘﺮدد ﻳﺼﻞ إﻟﻰ 3.8ﺝﻴﺠﺎ هﺮﺕﺰ Celeron D
وﺣﺪة اﻟﻤﻌﺎﻟﺠﺔ
Enha nced Intel SpeedStep® / Extended Memory )ﻓﻲ 8.0 / 2.0ﻓﻘﻂ ( Intel Core2Duo
اﻟﻤﺮآﺰﻳ ﺔ
64 Technology *It is recommende d to use
consumption.
اﻟﻨﺎﻗﻞ اﻷﻡﺎﻡﻲ
ﻡﻴﺠﺎ هﺮﺕﺰ 533 / 800 / 1066ﺕﺮدد
اﻟﺠﺎﻥﺒﻲ
ﻡﻴﺠﺎ ﺑﺎﻳﺖ64أﻗﺼﻰ ﺳﻌﺔ ﻟﺬاآﺮة اﻟﻔﻴﺪﻳﻮ اﻟﻤﺸﺘﺮآﺔ UniChr ome Pr oﻡﺪﻡﺠﺔ ﻓﻲ رﻗﺎﺋﻖ ﺑﻄﺎﻗﺔ اﻟﺮﺳﻮﻡﺎت
وﺿﻊ رﺋﻴﺴﻲ
48
P4M800 Pro-M7
اﻟﻤﻮاﺻﻔﺎت
ﺑﺤﻘﻬﺎ ﻓﻲ إﺿﺎﻓﺔ أو إزاﻟﺔ اﻟﺪﻋﻢ ﻷي ﻥﻈﺎم ﺕﺸﻐﻴﻞ ﺑﺈﺥﻄﺎر أو Biostarﺕﺤﺘﻔﻆ دﻋﻢ أﻥﻈﻤﺔ
Windows 2K / XP
ﺑﺪون إﺥﻄﺎر . اﻟﺘﺸﻐﻴﻞ
49
Motherboard Manual
JAPANESE
仕様
LGA 775
D processor up to 3.8 GHz Hyper -Thre ading / Exec ute Disabl e Bit /
CPU Intel Core2Duo Processor (Ver 2.0 / Enha nced Intel SpeedStep® / Extended Memory
ト VIA VT8237R+
グラフィッ
UniChrome Pro チップセットに統合 最大の共有ビデオメモリは64MBです
クス
DDR2 DIMMスロット x 2
最大メモリ容量2GB
もっとも一般に使用されるレガシー H/Wモニター
Super I/O
Super I/O機能を採用しています。 ファン速度コントローラ/ モニター
低ピンカウントインターフェイス ITEの「スマートガーディアン」機能
SATAバージョン1.0仕様に準拠。
SATA 統合シリアルATAコントローラ
最高1.5 Gb/秒のデータ転送速度
10 / 100 Mb/秒のオートネゴシエーション
LAN PHY Realtek RTL8201BL/RTL8201CL
半/全二重機能
サウンド 6チャンネルオーディオアウト
ALC 655
Codec AC’97バージョン2.3
AGPスロット x1
スロット CNRスロット x1
PCIスロット x3
50
P4M800 Pro-M7
仕様
各コネクタは2つのフロッピードライブをサポートし
フロッピーコネクタ x1
ます
IDEコネクタ x2 各コネクタは2つのIDEデバイスをサポートします
SATAコネクタ x2 各コネクタは1つのSATAデバイスをサポートします
フロントパネルコネクタ x1 フロントパネル機能をサポートします
フロントオーディオコネクタ x1 フロントパネルオーディオ機能をサポートします
CDインコネクタ x1 CDオーディオイン機能をサポートします
S/PDIFアウトコネクタ x1 デジタルオーディオアウト機能をサポートします
オンボード
CPUファンヘッダ x1 CPUファン電源装置(スマートファン機能を搭載)
コネクタ
システムファンヘッダ x1 システムファン電源装置
シャーシオープンヘッダ x1
シャーシ侵入検出機能
(オプション)
CMOSクリアヘッダ x1
各コネクタは2つのフロントパネルUSBポートをサポ
USBコネクタ x2
ートします
電源コネクタ(20ピン) x1
電源コネクタ(4ピン) x1
PS/2キーボード x1
PS/2マウス x1
シリアルポート x1
背面パネル プリンタポート x1
I/O VGAポート x1
LANポート x1
USBポート x4
オーディオジャック x3
ボードサイ
201 mm (幅) X 244 mm (高さ)
ズ
OSサポー Biostarは事前のサポートなしにOSサポートを追加ま
Windows 2K / XP
ト たは削除する権利を留保します。
2007/02/27
51