Documentos de Académico
Documentos de Profesional
Documentos de Cultura
2. The amount of acid left over is measured by titrating it with sodium hydroxide (NaOH)
to produce sodium chloride (NaCl) and water. Adding phenolphthalein indicator to the
solution causes it to turn pink when all the acid has reacted.
HCl + NaOH ⇒ NaCl + H2O
Distilled water
2 mm mesh sieve
Scientific balance
Hot plate
Filter papers
Filter funnels
100 ml volumetric flasks
20 ml glass pipette
10 ml glass pipette
Pipette bulb
Dropping pipette
50 ml measuring cylinder
Method
1. Sieve the air-dried soil and retain the less than 2 mm fraction. Grind this roughly
in the pestle and mortar.
2. Weigh out 10 g of the ground soil. Recording the exact weight (M) to 0.01 g.
4. Allow the sample to react until the effervescence stops. Then place the flask on a
hotplate and boil gently for 10 minutes.
5. Allow to cool, then filter the solution into 100 ml volumetric flasks. Make up to
volume (mark on neck of flask) with distilled water.
7. Clamp the burette so that it is vertical with enough space below to place the
conical flask. Fill the burette with 0.1M NaOH to the 0 ml mark, and place a piece
of white paper underneath the burette. Stand the flask holding the solution on
the paper under the tap of the burette.
8. Controlling the burette tap with one hand and holding the conical flask in the
other, slowly allow the NaOH to run into the flask, swirling the flask all the time to
mix the two solutions. Stop as soon as the solution in the flask develops a
permanent pink colour. Record the volume of NaOH (V) you have added by
reading off the scale on the side.
9. Repeat steps 5-7 using another 10 ml fraction from the same sample. Then
average the two results.
Calculation
1. The number of moles of NaOH you have used in the titration is: 0.1 x (A verage /
1000) = W x 10 -3 mol NaOH
2. In the equation equal numbers of moles of NaOH and HCl react together so W
also = W x 10-3 mol HCl in the 10 ml of fraction.
3. This 10 ml was drawn from 100 ml of solution so the number of moles in the 100
ml of solution is: (W x 10-3) x 10 = X mol HCl left over from the reation with the
carbonates in the soil.
4. The 20 ml of 2M HCl originally added to the soil contained 0.04 mol HCl.
Therefore the number of mols of acid that reacted with the carbonate is: 0.04 - X
= Y mol HCl
5. The molecular mass of CaCO3 is 100.1 g. 2 mols of HCl react with 1 mol (100.1
g) of CaCO3. Therefore,
For example if 10 g of soil were analysed and 12 ml of 0.1M NaOH was used in the
titration.
4. The amount of HCl that reacted with the soil is 0.04 - 0.012 = 0.028 mol HCl.
6. This means that the percentage CaCO3 in the air-dried soil is 1.4 x (100 / 10) =
14.01%
Safety
Some of the chemicals used in the method are toxic or highly corrosive. Always consult
chemical safety data sheets and follow appropriate health and safety protocols before
handling or using chemicals.
Many chemical saftey data sheets are available here from this Oxford University based
database.
References
Rowell, D.L. (1994) Soil Science: methods and applications. Harlow, Longman
Scientific and Technical. ISBN: 0582087848