Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Potentiometer for
anti-overlap adjustment
Introduction
The CBC-802 is a solid-state clutch/brake control
designed for operation of all Warner Electric 90 volt Failure to follow these instructions
DC clutches and brakes with the exception of the high may result in product damage, equipment damage,
torque series. It should not be used to directly power and serious or fatal injury to personnel.
Warner Electric permanent magnet electrically released
brakes as the units require an adjustable current or
voltage supply to provide optimum release. Specifications
The CBC-802 clutch/brake control is a direct plug-in Power Input 120VAC ±10% 50/60 HZ
replacement for the previous MCS-802-2 control. The Output 90 VDC full wave rectified.
difference between the two versions is that the CBC-802 0.50 amps maximum.
has a potentiometer for adjustment of the anti-overlap
Fusing 1/2 amp, Slo Blo, 5 x 20mm (internal)
between clutch and brake where the MCS-802-2 was
Replacement: Buss# GDC-500mA or
switch selectable for preset times only. Additionally, the
Littlefuse# 0218.500MXP
fuse changed for a 3AG type for the MCS-802-2 to a
5 x 20mm type fuse on the CBC-802. Also included in Switching Momentary contact, maintained
the CBC-802 are LED indicators indicating when the contact, or solid state open collector
brake or clutch is energized. logic.
Minimum contact rating 20VDC
Note: This design of the CBC-802 is mounted
resistive, 0.01 amps.
90 degrees counter-clockwise in it’s socket,
compared to the previous design CBC-802. Minimum input pulse – 1 millisecond.
Time Delay Adjustable potentiometer for
The CBC-802 clutch/brake control is designed to switch
0 to 100ms - between channels
between a clutch/brake combination, two clutches or
two brakes, one unit on at a time. Control design is such Dimensions Approx. 3-1/2’’ high x 2-1/2’’ wide x
that on power up, the brake channel energizes initially, 1-3/4’’ deep.
with normal switching inputs. The time delay feature Ambient
is designed to minimize clutch/brake interaction by Temperature -20° to +122°F (-29° to +50°C)
reducing clutch/brake torque overlap. Indicator LED’s on
the control show when the brake channel (RED) or clutch Cycle Rate Consult the Application Engineering
channel (GREEN) is energized. An internal fuse provides section of Warner Electric’s Master
protection from overload conditions. Additionally Catalog, P-1234-WE, for capabilities in
the control is protected against output short circuit your application.
conditions. The control does not protect from AC ground
loops or faults on the DC output side.
Model Part No.
The control mounts in one of the two optional octal
CBC-802 6002-448-002
sockets which are purchased separately. Wiring is made
at the socket terminals. Octal Socket, Foot Mounted 6001-101-001
Din Rail Mount Octal Socket 6001-101-002
1.57" 2.39"
(39.9) (60.7)
.71"
(18)
1.57" 2.40"
(39.9) (61)
4 Term 1-2 0V
6 5 3
Term 1-3 0V
Term 1-4 0V
ACV Term 1-5 (line
voltage 120V)
Term 1-6 0V
7 8 1 2 Term 1-7 0V
Term 1-8 0V
Warner Electric LLC warrants that it will repair or replace (whichever it deems advisable) any product
manufactured and sold by it which proves to be defective in material or workmanship within a period of one (1)
year from the date of original purchase for consumer, commercial or industrial use.
This warranty extends only to the original purchaser and is not transferable or assignable without Warner Electric
LLC’s prior consent.
Warranty service can be obtained in the U.S.A. by returning any defective product, transportation charges
prepaid, to the appropriate Warner Electric LLC factory. Additional warranty information may be obtained by
writing the Customer Satisfaction Department, Warner Electric LLC, 449 Gardner Street, South Beloit, Illinois
61080, or by calling 815-389-3771.
A purchase receipt or other proof of original purchase will be required before warranty service is rendered. If
found defective under the terms of this warranty, repair or replacement will be made, without charge, together
with a refund for transportation costs. If found not to be defective, you will be notified and, with your consent, the
item will be repaired or replaced and returned to you at your expense.
This warranty covers normal use and does not cover damage or defect which results from alteration, accident,
neglect, or improper installation, operation, or maintenance.
Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply
to you.
Warner Electric LLC’s obligation under this warranty is limited to the repair or replacement of the defective
product and in no event shall Warner Electric LLC be liable for consequential, indirect, or incidental damages of
any kind incurred by reason of the manufacture, sale or use of any defective product. Warner Electric LLC neither
assumes nor authorizes any other person to give any other warranty or to assume any other obligation or liability
on its behalf.
WITH RESPECT TO CONSUMER USE OF THE PRODUCT, ANY IMPLIED WARRANTIES WHICH THE
CONSUMER MAY HAVE ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL
CONSUMER PURCHASE. WITH RESPECT TO COMMERCIAL AND INDUSTRIAL USES OF THE PRODUCT,
THE FOREGOING WARRANTY IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES, WHETHER
EXPRESSED OR IMPLIED BY OPERATION OF LAW OR OTHERWISE, INCLUDING, BUT NOT LIMITED TO,
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty gives you specific legal rights and you may also have
other rights which vary from state to state.
www.warnerelectric.com
31 Industrial Park Road
New Hartford, CT 06057
815-389-3771
www.altramotion.com
Fax: 815-389-2582