Documentos de Académico
Documentos de Profesional
Documentos de Cultura
00 INTERNAL
Product Appearance
The height of an ATN 950 chassis is 2U. The ATN 950 provides 2 slot for the
multifunctional system control board and 6 slots for multi-service interface boards.
Product Features
The ATN 950 has special features such as access of multi-service through multimedia, clock
transport through any media, and high-precision frequency and time synchronization. When
used with the U2000, which is easy to use, the ATN 950 helps customers to decrease the
network total cost of ownership (TCO) in an integrated manner and increase efficiency of
deployment and O&M.
100% router structure, which satisfies the requirement for multi-service bearing;
LTE orientation, which fully protects customer investment
The ATN 950 adopts an advanced router structure, and therefore it has complete routing
functions. The ATN 950 forwards services based on the MPLS or MPLS-TP technology,
and builds an ALL IP-oriented uniform bearer platform for multiple services such as
TDM, ATM, Ethernet, and IP services. The ATN 950 features high bandwidth and small
delay, and enhances network flexibility and transport efficiency, which satisfy
requirements for evolving a bearer network to an LTE-oriented network.
Ideal clock solution and multi-service uniform access, which satisfy the requirement
of quick service deployment in complex scenarios
On the client side (UNI), the ATN 950 supports interfaces such as E1
(TDM/IMA/MLPPP) and FE/GE. On the network side (NNI), the ATN 910 supports
interfaces such as GE, FE, E1. In this manner, the ATN 950 supports access through
multiple media, and this eliminates limitations on access resources for network
deployment. The ATN 950 also supports IEEE 1588V2, synchronous Ethernet, 1588
ACR, E1 line, and NTR*clocks. These clock solution fully satisfies the requirement for
high-precision clocks on mobile backhaul networks and saves additional investment in
synchronization networks.
Visualized NMS, one-key service provision, and quick fault locating, which greatly
enhance the O&M capability of packet networks
With the design of templates and graphics, the U2000 provides visualized management
in a uniform manner. In addition, it provides complete OAM and fault detection
mechanisms. These enable you to quickly deploy services in batches on the U2000 by
clicking one key. Therefore, the service O&M capability and maintenance efficiency of
packet networks are greatly enhanced. In addition, the U2000 manages access network
equipment, transport network equipment, and metropolitan network equipment in an
integrated manner, avoids the dead zone of layered network management, and enhances
the capability of network O&M.
Figure 1-1 Typical application of the ATN 950 on an FMC metropolitan network
The previous figure shows typical application of the ATN 950. The ATN 950 is located at the
access layer of an FMC metropolitan network. As an end node, the ATN 950 provides
multi-service access. In this manner, the ATN 950 help build a highly efficient mobile
backhaul network with ALL IP orientation.
Product Specifications
Specification ATN 950
Physical specifications
Subrack dimensions (mm) 442 (W) x 220 (D) x 88.9 (H)
Subrack weight (kg) Empty subrack: 2.8 (without boards); full configuration: 8.42
Working voltage (V) –38.4 V to –72 V (DC voltage)
Typical and maximum power 95
consumption (W)
Ambient temperature –20°C to +60°C; short-term running: –25°C to +65°C
Relative humidity 10% RH to 90% RH; short-term running: 5% RH to 95% RH
System specifications
Backplane capacity 8Gbit/s
Synchronization specifications
Supports output or input of two external clocks.
Supports the IEEE 1588V2 protocol.
Clock synchronization
Supports the synchronous Ethernet clock.
Supports the IEEE 1588 ACR, CES ACR clock.
Protection specifications
Network protection Supports MPLS LSP 1:1 protection.
Supports MPLS TE-FRR VPN FRR.
PW Redundancy.
Link protection Supports inverse multiplexing for ATM (IMA) E1 protection.
Supports working/protection link aggregation group (LAG)
protection.
Clock protection Supports protection for multiple clocks.
Power supply protection Supports 1+1 power supply protection.
Software specifications
E1(75ohm/120ohm) Supports IMA, TDM, ML-PPP
Supports a maximum of 16 IMA groups, each of which supports a
maximum of 16 members.
MAC Supports learning of 32k MAC addresses (a maximum of 1k static
MAC addresses).
STP Supports MSTP, which is compatible with RSTP/STP.
Layer 2
LACP Support
features
VLAN Number of VLAN tags: 4k
Supports standard VLAN, QinQ VLAN.
Offload Support the separation of data and voice transmission
Multicast Supports IGMP snooping V2.
Routing protocol Supports OSPFv2, RIPv2, and IS-IS protocols.Supports static routing.
VLAN IF interfaces Supports 32 VLAN IF interfaces.
Layer3
ARP Supports dynamic ARP and static ARP table entries.
Features
DHCP DHCP client and DHCP relay
GRE tunnel Supports PW over GRE tunnel.
* Indicates a feature that will be provided in the ATN 950 of later versions.