Documentos de Académico
Documentos de Profesional
Documentos de Cultura
5. Dimensions
Switching unit: 2281-1-Relay Probe KLN-2XX
67,5
45
90
35
Georg Fischer Piping Systems Ltd CH-8201 Schaffhausen
Phone +41(0)52 631 30 26 / info.ps@georgfischer.com / 3,4
www.gfps.com
Ø6
Follow instruction manual
38
121
3 4
The instruction manual is part of the product and an important element within the safety M20x1,5 1 2
concept. C
• Read and follow instruction manual.
• Always keep instruction manual available for the product.
33
38
• Pass on instruction manual to all subsequent users of the product. 1 ½ BSP
80
M6
1. Intended use
The product is applicable for liquids with specific conductivity over 10 µS/cm. The
switching unit can sense the resistance between probes. Conductivity measurement is
suitable only for detecting the presence of liquid at a given level of the tank. This level 6. Installation
is represented by the length of the probe. The conductive switch is suitable for filling / • Mount switching unit on DIN EN 60715 rail.
emptying control or level limit. • Cut the KLN-2 type probes to the length required for level detection on site.
• Screw probes into the sockets.
2. Safety and responsibility • Tighten the probe with an M6 nut.
In order to provide safety in the plant, the operator is responsible for the following • Use separators at every 0.5 m for multiple probe devices to keep the probes apart.
measures:
• Products may only be used for its intended purpose, see intended use 7. Electrical Connection
• Never use a damaged or defective product. lf the wall of the tank is conductive no reference probe is needed, ln this case terminal C
Immediately sort out damaged product. is to be connected to the tank. On multiple probe units E1 and E2 are marked with
• Make sure that the piping system has been installed professionally and serviced 1,,.4, the reference probe is marked with C. Admissible length of cable between signal
regularly. processor and probes depends on cable capacity and conductivity.
• Products and equipment shall only be installed by persons who have the required
training, knowledge and experience.
• Regularly train personnel in all relevant questions regarding locally applicable
regulations, safety at work, environmental protection especially for pressurised pipes. Un
Un
A1 A2
. C E2
E1 E2
E1
max
Georg Fischer Piping Systems Ltd CH-8201 Schaffhausen
Phone +41(0)52 631 30 26 / info.ps@georgfischer.com /
www.gfps.com
min
GFDO 6354_4 (07.14)
© Georg Fischer Rohrleitungssysteme AG 16 C
CH-8201 Schaffhausen/Schweiz, 2014
Printed in Switzerland
t t t1 t t
Power supply terminals
EMPTYNG
Power supply indicator Un
E1 E2
(green LED) Output indicator
max
level
(red LED) min
Un
Function
9. Maintenance, Repair
Delay adjustment 3
4
5 6 7
8
The device does not require regular maintenance. Repair within and beyond the wananty
2
1
9
10
period is carried out at the manufacturer‘s location.
16 C 10. Storage
• Ambient temperature: -30 to +70 °C
Probe connection terminal
15 18
• Relative humidity: max. 85%
Output terminals
11. Disclaimer
The technical data are not binding. They neither constitute expressly warranted cha-
racteristics nor guaranteed properties nor a guaranteed durability.
They are subject to modification. Our General Terms of Sale apply.
8.2 LED Indication
Green LED is on • power supply is on
Red LED is on • relay is switched on (contacts 15 and 18 are closed)
Red LED is off • relay is disconnected (contacts 15 and 16 are closed)
Red LED is blinking • output delay indication
Un
A1 A2
E1 E2
max
16 C
15 18