Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Members
(Struktur yang Dibebani
secara Aksial)
Introduction
0 Structural components subjected only to tension or
compression are known as axially loaded members.
0 Examples: solid bar with straight longitudinal axes, coil
spring, cable.
0 Solid bars examples:
TRUSS
2
Introduction
0 Solid bars examples:
Column on building
struts
spokes
3
Introduction
0 Coil spring & cables examples:
4
Uniaxial Stress and Strain
0 Stress and strain are called uniaxial stress and strain if the
deformation of the bar be uniform throughout its volume,
which is the bar should be prismatic, the loads act through
the centroids of the cross sections, and the material be
homogeneous.
0 Homogeneous : the same throughout all parts of the bar
7
CHANGES IN LENGTHS OF
AXIALLY LOADED MEMBERS
Prismatic Bars
0 The elongation δ
8
CHANGES IN LENGTHS OF
AXIALLY LOADED MEMBERS
Cables
0 cables are often referred to as wire rope
0 The cross-sectional area is equal to the total cross sectional
area of the individual wires, called the effective area or
metallic area.
9
CHANGES IN LENGTHS OF
AXIALLY LOADED MEMBERS
Remember
10
CHANGES IN LENGTHS OF
AXIALLY LOADED MEMBERS
Example:
0 The device shown in Fig. 2-8a consists
of a horizontal beam ABC supported by
two vertical bars BD and CE. Bar CE is
pinned at both ends but bar BD is fixed
to the foundation at its lower end. The
distance from A to B is 450 mm and
from B to C is 225 mm. Bars BD and CE
have lengths of 480 mm and 600 mm,
respectively, and their cross-sectional Assuming that beam ABC
areas are 1020 mm2 and 520 mm2, is rigid, find the maximum
respectively. The bars are made of steel allowable load Pmax if the
having a modulus of elasticity E = 205 displacement of point A is
GPa. limited to 1.0 mm. 11
CHANGES IN LENGTHS OF
AXIALLY LOADED MEMBERS
Solution:
0 Free body diagram
shortening
12
CHANGES IN LENGTHS OF
AXIALLY LOADED MEMBERS
Solution: Note:
0 Displacement diagram 1. Member CE is in tension and member BD
is in compression.
2. Beam ABC is rigid
• From triangles A’A”C’ and B’B”C’
13
α = 0.11° .
CHANGES IN LENGTHS UNDER
NONUNIFORM CONDITIONS
0 change in length of a
prismatic bar of linearly
A. Bars with Intermediate Axial Loads
• Procedure to calculate change of the length:
elastic material loaded 1. Identify the segments of the bar (segments AB, BC,
only at the ends, is, and CD) as segments 1, 2, and 3, respectively.
2. Determine the internal axial forces N1, N2, and
δ=PL/EA N3 in segments 1, 2, and 3, respectively. Sign
Convention = tensile—positive; compression—
negative.
15
CHANGES IN LENGTHS UNDER
NONUNIFORM CONDITIONS
C. Bars with Continuously Varying Loads or Dimensions
𝑑 𝐷−𝑑 2 4𝑃𝐿
A=𝜋
2
+
2𝐿
𝑥 δ = ΔL =
π𝐷𝑑𝐸
16
CHANGES IN LENGTHS UNDER
NONUNIFORM CONDITIONS
D. Effect of Weight
X
W = ρ.A.y
𝑊𝐿
δ = ΔL =
2𝐴𝐸
17
CHANGES IN LENGTHS UNDER
NONUNIFORM CONDITIONS
Example.
18
CHANGES IN LENGTHS UNDER
NONUNIFORM CONDITIONS
Example.
A vertical steel bar ABC is pin-supported at its
upper end and loaded by a force
P1 at its lower end . A horizontal beam BDE is
pinned to the vertical bar at joint B and supported
at point D. The beam carries a load P2 at end E. The
upper part of the vertical bar (segment AB) has
length L1= 20.0 in. and cross-sectional area A1 =
0.25 in2; the lower part (segment BC) has length L2
= 34.8 in. and area A2 = 0.15 in2 . The modulus of
elasticity E of the steel is 29.0 x 106 psi. The left-
and right-hand parts of beam BDE have lengths a =
28 in. and b = 25 in., respectively. Calculate the
vertical displacement δC at point C if the load Pl =
2100 lb and the load P2 = 5600 lb. (Disregard the
19
weights of the bar and the beam.)
CHANGES IN LENGTHS UNDER
NONUNIFORM CONDITIONS
Solution.
0 Free body diagram
Taking moments about point D,
δC = 0.0088 in.
21
STATICALLY
INDETERMINATE STRUCTURES
0 Struktur Statis Tertentu/statically determinate
structure: Struktur dimana gaya-gaya reaksi dan
internalnya dapat diperoleh hanya dengan diagram
benda bebas dan keseimbangan statis. Tidak perlu
mengetahui besaran bahan.
0 Contoh: gambar di samping, dapat ditentukan R dan
gaya internal tanpa harus mengetahui
bahan/material batang, yaitu R = P1 + P2
22
Definisi
0 Struktur Statis Tak-Tentu: Struktur di mana
gaya-gaya reaksi dan internalnya tidak dapat
diperoleh hanya dengan diagaram benda bebas
dan keseimbangan statis.
(a)
(b)
24
Definisi
0 Maka, perpanjangan (sama dengan peralihan)
segmen AC,
0 δBC = ?
0 Tegangan pada segmen AC,
27
Jawaban
28
Perubahan Panjang karena Dua Jenis Bahan
Berbeda
persamaan keserasian
29
Hubungan gaya-
peralihan
Perubahan Panjang karena Dua Jenis Bahan
Berbeda
31
32
33
34
35
36