Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Technical Information
Orbital Motors
OMS, OMT and OMV
powersolutions.danfoss.com
Technical Information OMS, OMT and OMV Orbital Motors
February 2016 Corrected Hardening specification for OMSS, OMTS, OMVS 0601
Contents
Orbital motors
Characteristic, features and application areas of Orbital Motors....................................................................................5
Characteristic features of Danfoss Orbital Motors.......................................................................................................... 5
Technical features of Danfoss Orbital Motor.....................................................................................................................5
The Danfoss Orbital Motors are used in the following application areas:..............................................................6
Survey of literature with technical data on Danfoss Orbital Motors..............................................................................6
OMS, OMT and OMV
Speed, torque and output.............................................................................................................................................................7
OMS
Versions................................................................................................................................................................................................9
Features.......................................................................................................................................................................................... 9
Code numbers.................................................................................................................................................................................10
Ordering.......................................................................................................................................................................................10
Technical data................................................................................................................................................................................. 11
Maximum permissible shaft seal pressure...................................................................................................................... 12
Motor with check valves and without use of drain connection......................................................................... 12
Maximum return pressure................................................................................................................................................12
Pressure drop in motor...........................................................................................................................................................13
Oil flow in drain line.................................................................................................................................................................13
Direction of shaft rotation..................................................................................................................................................... 13
Permissible shaft loads for OMS..........................................................................................................................................13
Function diagrams.........................................................................................................................................................................18
Function diagram use............................................................................................................................................................. 22
Shaft version.................................................................................................................................................................................... 23
Port thread versions ................................................................................................................................................................26
Dimensions.......................................................................................................................................................................................26
Standard flange—European version.................................................................................................................................27
Standard flange—US version...............................................................................................................................................29
Special flange—European version.....................................................................................................................................31
A-2 flange—US version.......................................................................................................................................................... 32
Magneto flange—US version...............................................................................................................................................34
SAE-B flange—US version..................................................................................................................................................... 36
Wheel—European version.................................................................................................................................................... 38
Wheel—US version.................................................................................................................................................................. 40
Short—European version...................................................................................................................................................... 42
OMSS.................................................................................................................................................................................................. 43
Installing the OMSS..................................................................................................................................................................43
Attached component dimensions .....................................................................................................................................43
Internal spline data for the component to be attached.............................................................................................43
Motor or attached component drain connection.........................................................................................................44
OMT
Versions............................................................................................................................................................................................. 46
Features........................................................................................................................................................................................46
Code numbers.................................................................................................................................................................................46
Ordering.......................................................................................................................................................................................47
Technical data................................................................................................................................................................................. 47
Maximum permissible shaft seal pressure...................................................................................................................... 47
Motor with check valves and without use of drain connection......................................................................... 47
Motor with check valves and with drain connection............................................................................................. 47
Maximum return pressure................................................................................................................................................48
OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH......................................................................................................48
Pressure drop in motor...........................................................................................................................................................50
Oil flow in drain line.................................................................................................................................................................50
Direction of shaft rotation..................................................................................................................................................... 51
Permissible shaft loads for OMT..........................................................................................................................................51
Function diagrams.........................................................................................................................................................................54
Function diagram use............................................................................................................................................................. 56
Shaft version.................................................................................................................................................................................... 57
Contents
Port thread versions.................................................................................................................................................................60
Dimensions.......................................................................................................................................................................................61
Standard flange—European version.................................................................................................................................61
Standard flange—US version...............................................................................................................................................63
Wheel—European version.................................................................................................................................................... 65
Wheel—US version.................................................................................................................................................................. 67
Brake-wheel—European version........................................................................................................................................ 69
Brake-standard—European version.................................................................................................................................. 71
Short—European version...................................................................................................................................................... 72
OMTS.................................................................................................................................................................................................. 73
Installation...................................................................................................................................................................................73
Attached component dimensions......................................................................................................................................73
Attached component internal splines.............................................................................................................................. 74
Motor or attached component drain connection.........................................................................................................75
OMV
Versions............................................................................................................................................................................................. 76
Features........................................................................................................................................................................................76
Code numbers.................................................................................................................................................................................76
Ordering.......................................................................................................................................................................................77
Technical data................................................................................................................................................................................. 77
Technical data for OMV, OMVW and OMVS.................................................................................................................... 77
Maximum permissible shaft seal pressure...................................................................................................................... 77
Motor with check valves and without use of drain connection......................................................................... 77
Maximum return pressure................................................................................................................................................78
Pressure drop in motor...........................................................................................................................................................78
Oil flow in drain line.................................................................................................................................................................79
Direction of shaft rotation..................................................................................................................................................... 79
Permissible shaft loads for OMV..........................................................................................................................................79
Function diagrams.........................................................................................................................................................................81
Function diagram use............................................................................................................................................................. 84
Shaft version.................................................................................................................................................................................... 85
Port thread versions.................................................................................................................................................................88
Dimensions.......................................................................................................................................................................................89
Standard flange—European version.................................................................................................................................89
Standard flange—US version...............................................................................................................................................91
SAE-C flange—US version..................................................................................................................................................... 93
Wheel—European version.................................................................................................................................................... 95
Wheel—US version.................................................................................................................................................................. 97
Short—European version...................................................................................................................................................... 98
OMVS.................................................................................................................................................................................................. 99
Installation...................................................................................................................................................................................99
Attached component dimensions......................................................................................................................................99
Attached component internal splines............................................................................................................................100
Motor or attached component drain connection...................................................................................................... 101
Weight of motors
Code number and weight ....................................................................................................................................................... 102
Orbital motors
Danfoss is a world leader within production of low speed orbital motors with high torque. We can offer
more than 3,000 different orbital motors, categorised in types, variants and sizes (including different shaft
versions).
The motors vary in size (rated displacement) from 8 cm³ [0.50 in³] to 800 cm³ [48.9 in³] per revolution.
Speeds range up to approximate 2,500 min-1 (rpm) for the smallest type and up to approximate 600 min-1
(rpm) for the largest type.
Maximum operating torques vary from 13 N•m [115 lbf•in] to 2,700 N•m [24,000 lbf•in] (peak) and
maximum outputs are from 2.0 kW [2.7 hp] to 70 kW [95 hp].
Orbital motors
• Motors with corrosion resistant parts
• Wheel motors with recessed mounting flange
• OMP, OMR- motors with needle bearing
• OMR motor in low leakage version
• OMR motors in a super low leakage version
• Short motors without bearings
• Ultra short motors
• Motors with integrated positive holding brake
• Motors with integrated negative holding brake
• Motors with integrated flushing valve
• Motors with speed sensor
• Motors with tacho connection
• All motors are available with black finish paint
The Danfoss Orbital Motors are used in the following application areas:
• Construction equipment
• Agricultural equipment
• Material handling & Lifting equipment
• Forestry equipment
• Lawn and turf equipment
• Special purpose
• Machine tools and stationary equipment
• Marine equipment
A general survey brochure on Danfoss Orbital Motors gives a quick motor reference based on power,
torque, speed and capabilities.
Max. speed
min-1
(rpm)
800
600
400
200
80 100 125 160 200 250 315 400 500 160 200 250 315 400 500 315 400 500 630 800
18000 2000
16000 1800
14000 1600
1400
12000
1200
10000
1000
8000
800
6000
600
4000
400
2000 200
80 100 125 160 200 250 315 400 500 160 200 250 315 400 500 315 400 500 630 800
hp kW Max. output
80 60
50
60 40
40 30
20
20 10
80 100 125 160 200 250 315 400 500 160 200 250 315 400 500 315 400 500 630 800
The bar diagrams above are useful for a quick selection of relevant motor size for the application. The
final motor size can be determined by using the function diagram for each motor size.
• OMS Function diagrams on page 18
• OMT Function diagrams on page 54
The function diagrams are based on actual tests on a representative number of motors from our
production. The diagrams apply to a return pressure between 5 and 10 bar [75 and 150 psi] when using
mineral based hydraulic oil with a viscosity of 35 mm²/s [165 SUS] and a temperature of 50°C [120°F]. For
further explanation concerning how to read and use the function diagrams, please consult the paragraph
"Selection of motor size" in the technical information "General Orbital motors" 520L0232.
OMS
Versions
OMS versions
Mounting Shaft Port size European US version Drain Check valve Main type
flange version connection designation
Standard Cyl. 32 mm G 1/2 X Yes Yes OMS
flange
Cyl. 1.25 in 7/8-14 UNF X Yes Yes OMS
Splined 1.25 in G 1/2 X Yes Yes OMS
7/8-14 UNF X Yes Yes OMS
Tapered 35 mm G 1/2 X Yes Yes OMS
Tapered 1.25 in 7/8-14 UNF X Yes Yes OMS
P.t.o. G 1/2 X Yes Yes OMS
Special flange Splined 1.25 in G 1/2 X Yes Yes OMS
A-2 Cyl. 1 in 7/8-14 UNF X Yes Yes OMS
flange
Cyl. 1.25 in 7/8-14 UNF X Yes Yes OMS
Splined 1 in 7/8-14 UNF X Yes Yes OMS
Splined 1.25 in 7/8-14 UNF X Yes Yes OMS
Tapered 1.25 in 7/8-14 UNF X Yes Yes OMS
Magneto Cyl. 1 in 7/8-14 UNF X Yes Yes OMS
flange
Cyl. 1.25 in 7/8-14 UNF X Yes Yes OMS
Splined 1 in 7/8-14 UNF X Yes Yes OMS
Splined 1.25 in 7/8-14 UNF X Yes Yes OMS
SAE B flange Splined 1.25 in 7/8-14 UNF X Yes Yes OMS
Splined 0.875 in 7/8-14 UNF X Yes Yes OMS
Wheel Cyl. 32 mm G 1/2 X Yes Yes OMSW
Cyl. 1.25 in 7/8-14 UNF X Yes Yes OMSW
Tapered 35 mm G 1/2 X Yes Yes OMSW
Tapered 1.25 in 7/8-14 UNF X Yes Yes OMSW
Short No output shaft G 1/2 X Yes Yes OMSW
Features
Features available (options):
• Speed sensor
• Motor with tacho connection
• High pressure shaft seal
• Viton shaft seal
• Painted
• Ultra short
• Motor with drum brake
OMS
Code numbers
Ordering
Add the four digit prefix “151F” to the four digit numbers from the chart for complete code number.
Example:
151F0504 for an OMS 200 with standard flange, cyl. 32 mm shaft and port size G 1/2.
OMS
Technical data
Type OMS OMS OMS OMS OMS OMS OMS OMS OMS
OMSW OMSW OMSW OMSW OMSW OMSW OMSW OMSW OMSW
OMSS OMSS OMSS OMSS OMSS OMSS OMSS OMSS OMSS
Motor size 80 100 125 160 200 250 315 400 500
Geometric displacement cm3 80.5 100.0 125.7 159.7 200.0 250.0 314.9 393.0 488.0
[in3] [4.91] [6.10] [7.67] [9.75] [12.20] [15.26] [19.22] [23.98] [29.78]
Max. speed min-1 cont. 810 750 600 470 375 300 240 190 155
[rpm]
int1) 1000 900 720 560 450 360 285 230 185
Max. torque Nm cont. 240 305 375 490 610 720 825 865 850
[lbf·in] [2120] [2700] [3320] [4340] [5400] [6370] [7300] [7660] [7520]
int.1) 310 390 490 600 720 870 1000 990 990
[2740] [3450] [4340] [5310] [6370] [7700] [8850] [8760] [8760]
Max. output kW cont. 15.5 18.0 18.0 16.5 16.5 14.5 15.0 11.0 9.0
[hp] [20.8] [24.1] [24.1] [22.1] [22.1] [19.4] [20.1] [14.8] [12.1]
int.1) 19.5 22.5 22.5 23.0 22.0 18.0 17.0 12.5 10.5
[26.2] [30.2] [30.2] [30.8] [29.5] [24.1] [22.8] [16.8] [14.1]
Max. pressure drop bar cont. 210 210 210 210 210 200 200 160 120
[psi] [3050] [3050] [3050] [3050] [3050] [2900] [2900] [2320] [1740]
int.1) 275 275 275 260 250 250 240 190 140
[3990] [3990] [3990] [3770] [3630] [3630] [3480] [2760] [2030]
peak2) 295 295 295 280 270 270 260 210 160
[4280] [4280] [4280] [4060] [3920] [3920] [3770] [3050] [2320]
Max. oil flow l/min cont. 65 75 75 75 75 75 75 75 75
[USgal/min] [17.2] [19.8] [19.8] [19.8] [19.8] [19.8] [19.8] [19.8] [19.8]
int.1) 80 90 90 90 90 90 90 90 90
[21.1] [23.8] [23.8] [23.8] [23.8] [23.8] [23.8] [23.8] [23.8]
Max. starting pressure bar 12 10 10 8 8 8 8 8 8
with unloaded shaft [psi] [175] [145] [145] [115] [115] [115] [115] [115] [115]
Min. starting torque at max. press. drop cont. 180 230 290 370 470 560 710 710 660
Nm [lbf·in] [1590] [2040] [2570] [3270] [4160] [4960] [6280] [6280] [5840]
at max. press. drop int.1) 235 300 380 460 560 700 850 840 770
Nm [lbf·in] [2080] [2660] [3360] [4070] [4960] [6200] [7520] [7430] [6820]
1) Intermittent operation: the permissible values may occur for max. 10% of every minute.
2) Peak load: the permissible values may occur for max. 1% of every minute.
For max. permissible combination of flow and pressure, see function diagram for actual motor.
OMS
Maximum permissible shaft seal pressure
151-320.10
P P
psi bar
1500
100
90
1200
80
70
900
60
50
600 40
30
300 20
10
0 0
0 100 200 300 400 500 600 700 800 max. min-1
(rpm)
151-1674.10
– – – – Intermittent operation: the permissible values may occur for max. 10% of every minute.
Continuous operation
OMS
Pressure drop in motor
∆p ∆p
psi bar
16
200 14
12
150 10
8
100
6
4
50
2
0 0 Q
0 10 20 30 40 50 60 70 80 90 l/min
Q
0 2 4 6 8 10 12 14 16 18 20 22 US gal/min
151-1408.10
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]
Maximum oil flow in the drain line at a return pressure less than 5-10 bar [75-150 psi]
Pressure drop Viscosity Oil flow in drain line
bar [psi] mm2/s [SUS] l/min [US gal/min]
140 [2030] 20 [100] 1.5 [0.40]
35 [165] 1.0 [0.26]
210 [3050] 20 [100] 3.0 [0.79]
35 [165] 2.0[0.53]
Mounting flange:
Standard – A-2 – Magneto – SAE B
OMS
Shaft:
Cyl. 32 mm – Cyl. 1.25 in – Splined 1.25 in.
Tapered 35 mm – Tapered 1.25 in – P.t.o.
Prad. Prad.
lbf N
7000
30000
0
6000 - + Pmax. =5000 N
=1124 lbf
25000
5000
20000
4000
15000
3000
10000
2000
5000
1000
0 0
-20 -10 0 10 20 30 40 50 60 70 80 mm
151-1962.10
Mounting flange:
Wheel
Shaft:
All shaft types
Prad. Prad.
lbf N
7000
30000
0
6000 - + Pmax. =5000 N
=1124 lbf
25000
5000
20000
4000
15000
3000
10000
2000
5000
1000
0 0
0 10 20 30 40 50 60 70 80 90 100 110 mm
151-1964.10
The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of the distance from
the mounting flange to the point of load application.
OMS
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at 100 min-1) at rated
output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows maximum radial shaft load. Any shaft load exceeding the values shown in the
curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing
dimensioning" in the technical information "General Orbital motors" 520L0232.
Mounting flange:
Special
Shaft:
Splined 1.25 in
Prad. Prad.
lbf N
7000
30000
0
6000 - + Pmax. =5000 N
=1124 lbf
25000
5000
20000
4000
15000
3000
10000
2000
5000
1000
0 0
-20 -10 0 10 20 30 40 50 60 70 80 mm
151-1960.10
Mounting flange:
A-2 – Magneto
Shaft:
Cyl. 1 in – Splined 1 in
OMS
Prad. Prad.
lbf N
20000
0
4000 - + Pmax. =5000 N
=1124 lbf
15000
3000
10000
2000
5000
1000
0 0
-20 -10 0 10 20 30 40 50 60 mm
151-1961.10
The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of the distance from
the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at 100 min-1) at rated
output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown in the curve will
involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing
dimensioning" in the technical information "General Orbital motors" 520L0232.
Mounting flange:
SAE B
Shaft:
Splined 0.875 in
OMS
Prad. Prad.
lbf N
20000
0
4000 - + Pmax. =5000 N
=1124 lbf
15000
3000
10000
2000
5000
1000
0 0
-20 -10 0 10 20 30 40 50 60 mm
151-1963.10
The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of the distance from
the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at 100 min-1) at rated
output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown in the curve will
involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing
dimensioning" in the technical information "General Orbital motors" 520L0232.
OMS
Function diagrams
Continuous range
Intermittent range (maximum 10% operation every minute)
OMS 80
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
30 l/min
[7.9 US gal/min]
40 l/min
[10.6 US gal/min]
50 l/min
[13.2 US gal/min]
65 l/min
[17.2 US gal/min]
Q=80 l/min
[21.1 US gal/min]
lbf• in Nm
3000
325
∆ p=275 bar
300 3990 psi
2500 250 bar
275
N=18kW 3630 psi
250
225 bar
2000 15kW 3260 psi
225 9kW
12kW 210 bar
18hp
200 3050 psi
15hp
175 6kW 175 bar
1500 9hp 2540 psi
6hp
150 140 bar
12hp
3kW 2030 psi
125
1000
100 η t =81% 105 bar
1520 psi
3hp 80%
75
70 bar
500 78% 1020 psi
50 1hp 75%
N=1kW 70%
25 η t =60% ∆ p= 30 bar
440 psi
0 0
0 100 200 300 400 500 600 700 800 900 1000 min-1
(rpm)
151-901.10
OMS 100
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
30 l/min
[7.9 US gal/min]
40 l/min
[10.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
4000 450
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 800 850 900 950 min-1
(rpm)
151-902.10
9hp
OMS
OMS 125
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
30 l/min
[7.9 US gal/min]
40 l/min
[10.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 min-1
(rpm)
151-903.10
OMS 160
lbf• in Nm
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
30 l/min
[7.9 US gal/min]
40 l/min
[10.6 US gal/min]
50 l/min
[13.2 US gal/min]
60 l/min
[15.9 US gal/min]
75 l/min
[19.8 US gal/min]
Q=90 l/min
[23.8 US gal/min]
6000
0 50 100 150 200 250 300 350 400 450 500 550 600 min-1
(rpm)
151-904.11
OMS
OMS 200
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
30 l/min
[7.9 US gal/min]
40 l/min
[10.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
7000
750
6000
700 ∆ p=250 bar
650 3630 psi
15hp 225 bar
N=21kW
600 3260 psi
9kW 15kW 18kW
5000 12kW 210 bar
550 12hp
6kW 3050 psi
500 175 bar
18hp 21hp 2540 psi
4000 450
6hp 160 bar
400 2320 psi
9hp 140 bar
3000 350 2030 psi
300
η t =88% 105 bar
250 86% 1520 psi
2000 3kW 85%
200
N=1kW 3hp 83% 80% 70 bar
150 1020 psi
1000 1hp 75%
100 70%
η t =60% ∆ p= 30 bar
50 440 psi
0 0
0 50 100 150 200 250 300 350 400 450 500 min-1
(rpm)
151-905.10
OMS 250
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
30 l/min
[7.9 US gal/min]
40 l/min
[10.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
151-1039.10
OMS
OMS 315
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
30 l/min
[7.9 US gal/min]
40 l/min
[10.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
10000
1100 ∆ p=240 bar
3480 psi
9000
1000 225 bar
3260 psi
8000 900
N=18kW 200 bar
2900 psi
7000 800 175 bar
15kW 2540 psi
6000 700 9kW 160 bar
12kW 18hp 2320 psi
600 15hp 140 bar
5000 12hp 2030 psi
500 6kW 9hp 120 bar
4000 1740 psi
400 6hp 100 bar
3kW 1450 psi
3000 η t =87% 80%
300
3hp 70 bar
N=1kW 85% 75% 1020 psi
2000
200 1hp 83% 70%
1000 100 η t =60% ∆ p= 35 bar
510 psi
0 0
0 25 50 75 100 125 150 175 200 225 250 275 300 min-1
(rpm)
151-906.10
OMS 400
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
30 l/min
[7.9 US gal/min]
40 l/min
[10.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
10000
1100 ∆ p=190 bar
2760 psi
9000 175 bar
1000
N=15kW 2540 psi
8000 900
160 bar
2320 psi
7000 800
12kW 140 bar
2030 psi
6000 700
6kW 9kW 15hp 120 bar
600 1740 psi
5000 9hp
3kW 12hp 105 bar
500 6hp 1520 psi
4000
400
3hp
η t =87% 80 bar
3000 1160 psi
300 N= 85% 60 bar
86%
2000 1kW 83% 870 psi
200 1hp 80%
1000 100
75%
70%
∆ p= 30 bar
η t =60% 440 psi
0 0
151-1491.10
OMS
OMS 500
Q=5 l/min
[1.3 US gal/min]
10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
30 l/min
[7.9 US gal/min]
40 l/min
[10.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
Q=90 l/min
[23.8 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
10000
1100
9000
1000
151-1984.10
Intermittent pressure drop and oil flow must not occur simultaneously.
OMS
Shaft version
48.4 [1.906]
58 [2.28] 47.6 [1.874]
min. 20 [0.78]
45˚ 18 [0.71] 45˚
R0.6 [0.024] 6 [0.24] A-A R0.4 [0.016] 3/8 -16 UNC A-A
A A
Ø31.750 [1.2500]
Ø31.699 [1.2480]
Ø32.018 [1.2605]
Ø32.002 [1.2599]
Ø35 [1.38]
35.00 [1.378]
34.71 [1.367]
Ø35 [1.38]
35.33 [1.391]
35.08 [1.381]
A B
M8
D
A A E
45.5 [1.791] 5.5 [0.217] 10.000 [0.3937] 9.4 [0.370]
45.0 [1.772] 4.5 [0.177] 9.964 [0.3923] 7.5 [0.295]
31.75 [1.250] 7.962 [0.3135]
56.5 [2.224] 31.37 [1.235] 7.937 [0.3125]
43.4 [1.708]
42.6 [1.678]
R0.5 [0.020]
min. 20 [0.78]
28.2 [1.110]
27.9 [1.098]
F
A 3.0 [0.118]
2.0 [0.079]
6.40 [0.252]
31.75 [1.250] 6.35 [0.250]
31.37 [1.235]
151-876.10
OMS
48.4 [1.906]
58 [2.28] 47.6 [1.874]
min. 20 [0.78]
18 [0.71]
45˚ A-A 45˚
R0.4 [0.016] 6 [0.24] R0.4 [0.016] 3/8 -16 UNC A-A
A A
Ø31.750 [1.2500]
Ø31.725 [1.2490]
Ø31.750 [1.2500]
Ø31.725 [1.2490]
Ø35 [1.38]
Ø35 [1.38]
D
M8
A A
38 [1.50] 35 [1.38]
36 [1.42] 32 [1.26]
min. 14 [0.55]
R2 [0.08]
A-A
¼ -20 UNC-2B *6.275 [0.2470]
*6.200 [0.2441]
A
Ø25.348 [0.9979]
Ø25.298 [0.9960]
Ø35 [1.38]
6x60˚
A
22.3 [0.878] 1[0.04]x45˚ *21.54 [0.848]
45˚ *21.40 [0.843]
21.7 [0.854]
43.4 [1.709]
42.6 [1.677]
151-1912.11
OMS
Ø18.6 [0.732]
Ø18.4 [0.724] J K
A-A A-A
A
A
M20x1.5 [0.591]
Ø4.5 [0.177]
Ø22.1 [0.870]
Ø21.9 [0.862]
Ø35 [1.38]
Ø35 [1.38]
Ø44 [1.73]
G H
19.0 [0.748]
19.1.[0.752]
R4 [0.16] A A L
R2.5 [0.098]
4 [0.16] 13 [0.51] 6.00 [0.236]
13.5 [0.531]
12.5 [0.492] 5.97 [0.235]
20 [0.79]
33.2 [1.307]
32.8 [1.291] 36 [1.42]
58 [2.28]
54.3 [2.138]
53.7 [2.114]
12.7 [0.500]
M 5 [0.20] A-A
45˚
A N
Ø31.775 [1.2510]
Ø31.725 [1.2490]
Ø35 [1.38]
Ø4 [0.15]
I
17.16 [0.676]
16.94 [0.677]
A
O
31.75 [1.250]
31.37 [1.235]
7.960 [0.3134]
35.6 [1.402]
7.940 [0.3126]
34.4 [1.354]
151-1915.10
OMS
100 [3.94]
8.6 3 [0.3
A
8.5
4[
0.3 36]
40
Ø34.85 [1.372]
Ø34.73 [1.367]
]
29.5 [1.161]
29.3 [1.154]
Ø40 [1.57]
151-1948.10
J P.t.o. shaft
DIN 9611 Form 1
(ISO/R500 without pin hole)
** Deviates from DIN 9611
D
C Ø21.4 [0.843]
Ø21.0 [0.827]
G H
min. 12 [0.47]
min. 12 [0.47]
151-1971.11
Dimensions
OMS
Standard flange—European version
Ø82.55 [3.250]
Ø82.50 [3.248]
1 [0.04]x45˚
R1 [0.04]
6.35 [0.250]
5.85 [0.230]
L3
18 [0.71] Ø13.5 [0.531]
66.5 [2.618]
64.5 [2.539]
Ø20 [0.79]
L2
48 [1.89]
L1
C
L
5.6 [0.22]
4.4 [0.17]
D
22.6 [0.890]
21.4 [0.850]
27.6 [1.047]
26.4 [1.039]
R13 [0.51]
40 [1.57]
R20 [0.78]
m
ax 106.8 [4.205]
m . 10
ax 5 106.0 [4.173]
. 12 [4
8 .1 max. 131 [5.157]
[5 3]
.0
4]
151-1809.10
OMS
OMS
Standard flange—US version
Standard flange
Ø82.55 [3.250]
Ø82.50 [3.248]
1 [0.04]x45˚
R1 [0.04]
6.35 [0.250]
5.85 [0.230]
Ø13.5 [0.531]
L3
18 [0.71]
66.5 [2.618]
64.5 [2.539]
Ø21 [0.83]
L2
56 [2.20]
L1
C
L
5.6 [0.22]
4.4 [0.17]
D
22.6 [0.890]
21.4 [0.850]
27.6 [1.047]
26.4 [1.039]
106.8 [4.205]
m
ax
106.0 [4.173]
.1
m
05
ax
.1
26
3]
[4
.9
6]
151-1972.10
OMS
OMS
Special flange—European version
Ø82.55 [3.250]
Ø82.50 [3.248]
1 [0.04]x45˚
R1 [0.04]
6.35 [0.250]
5.85 [0.230]
55 [2.17]
53 [2.09]
58 [2.28]
18 [0.71]
78.5 [3.091]
76.5 [3.012]
Ø20 [0.79]
L2
48 [1.89]
C
L1
L
5.6 [0.22]
4.4 [0.17]
E
22.6 [0.890]
21.4 [0.850]
27.6 [1.047]
26.4 [1.039]
Ø
Ø1 106
06 .8
.0 [4. max. 103 [4.06]
[4 20
.1 5]
73
]
151-1810.10
OMS
1 [0.04]x45˚
R1 [0.04]
6.35 [0.250]
5.85 [0.230]
Ø13.5 [0.531]
L3
18 [0.71]
66.5 [2.618]
64.5 [2.539]
Ø21 [0.83]
L2
56 [2.20]
L1
C
L
5.6 [0.22]
4.4 [0.17]
D
22.6 [0.890]
21.4 [0.850]
27.6 [1.047]
26.4 [1.039]
106.8 [4.205]
106.0 [4.173]
m
ax
.1
26
[4
.9
]6
151-1979.10
OMS
12 mm [0.47 in] deep
O-ring boss port
E: 7⁄8 - 14 UNF;
16.7 mm [0.657 in] deep
O-ring boss port
OMS
Magneto flange—US version
Ø88.55 [3.250]
Ø82.50 [3.248]
0.3 [0.012]x45˚
2.6 [0.102]
18.9 [0.744] Ø13.5 [0.531]
L3
Ø21 [0.83]
70 [2.75]
68 [2.68]
6xØ20 [0.79]
L2
56 [2.20]
L1
L
C
5.6 [0.22]
4.4 [0.17]
D
22.6 [0.890]
21.4 [0.850]
27.6 [1.047]
26.4 [1.039]
106.8 [4.205]
106.0 [4.173]
151-1980.10
OMS
OMS
SAE-B flange—US version
Ø101.60 [4.000] Ø56.5 [2.224]
Ø101.55 [3.998] Ø55.5 [2.185]
1 [0.04]x45˚
R1 [0.04]
9.7 [0.382]
9.3 [0.366]
18 [0.71] Ø14.3 [0.570]
L3
3.5 [0.138]
3.3 [0.130]
66.5 [2.618]
64.7 [2.547]
Ø21 [0.83]
L2
56 [2.20]
C
L
L1
5.6 [0.22]
4.4 [0.17]
D
22.6 [0.890]
21.4 [0.850]
27.6 [1.047]
26.4 [1.039]
Rmin. 14 [0.55]
max. 174 [6.85]
146.05 [5.750]
R10 [0.39]
m
ax
.1
26
[4
40 [1.57]
.9
6]
151-1981.10
OMS
OMS
Wheel—European version
Ø125.000 [4.9213]
Ø124.937 [4.9188] max. Ø73 [2.87]
58 [2.28]
16˚
104 [4.09]
102 [4.02]
1 [0.04]x45˚
R1 [0.04]
R6 [0.24]
43.9 [1.738]
42.5 [1.673]
9 [0.35]
7 [0.28]
Ø20 [0.79]
28.5 [1.12]
16 [0.63]
L2
48 [1.89]
L1
C
5.6 [0.22]
4.4 [0.17]
L
E
22.6 [0.890]
21.4 [0.850]
27.6 [1.047]
26.4 [1.039]
16.3 [0.642] 16.3 [0.642] R18 [0.71] max. 52 [2.05] max. 54 [2.13]
15.7 [0.618] 15.7 [0.618]
21.3 [0.839] 21.3 [0.839] 56 [2.20]
20.7 [0.815] 20.7 [0.815]
70 [2.76]
max. 103 [4.06]
R12 [0.47]
max. 139 [5.46]
max. 139 [5.46]
16
15 0.4 [6
9.6 .3
Ø13.5 [0.531]
[6. 15]
28
3]
151-1812.10
OMS
OMS
Wheel—US version
Ø127.05 [5.000]
Ø126.95 [4.998]
16˚
1 [0.04]x45˚
R6 [0.24]
R1 [0.04]
L3
8 [0.31]
16 [0.63]
Ø21 [0.83]
28.5 [1.12]
L2
56 [2.20]
L1
C
L
5.6 [0.22]
4.4 [0.17]
D
22.6 [0.890]
21.4 [0.850]
27.6 [1.047]
26.4 [1.039]
4]
37
[6.
1.9
Ø16
151-1982.10
OMS
OMS
Short—European version
C: Drain connection D: M10; 13 mm [0.51 in] deep E: G 1⁄2; 15 mm [0.59 in] deep
G 1⁄4; 12 mm [0.47 in] deep
OMS
OMSS
2.35 [0.093] C
2.25 [0.089] A
E
K 0.25 [0.010] B
K 0.1˚
Ø61.5 [2.421]
Ø60.5 [2.382]
min. Ø40 [1.57]
Ø108.0 [4.252]
Ø107.6 [4.236]
min. Ø4 [0.16]
Ø40.5 [1.594]
Ø40.3 [1.587]
Ø100 [3.94]
K
33 [1.30]
31 [1.22]
Ø29.5 [1.161]
Ø28.5 [1.122]
15 [0.59]
Ø35.5 [1.398]
Ø34.5 [1.358]
G H
F 6.2 [0.244] 16.5 [0.650]
8.4 [0.331] 5.8 [0.228] 15.5 [0.610]
27.3 [1.075] 8.0 [0.315] 28 [1.10]
26.7 [1.051] 26 [1.02]
52.3 [2.059]
34.2 [1.346]
51.7 [2.035]
33.8 [1.331]
151-873.10
D Conical seal ring E Internal drain channel F M10; min. 15 mm [0.59 in]
deep
OMS
Material:
Case hardening steel with a tensile strength corresponding at least to 20 MoCr4 (900 N/mm2) or SAE
8620.
Hardening specification:
• On the surface: HV = 750 ± 50
• 0.7 ± 0.2 mm under the surface: HV = 560
Internal involute spline data; Standard ANS B92.1-1970, class 5 (corrected m · X = 0.8; m = 2.1166)
Flat root side fit mm in
Number of teeth z 12 12
Pitch DP 12/24 12/24
Pressure angle 30° 30°
Pitch dia. D 25.4 1.0
Major dia. Dri 28.00 –0.1 1.10 0–0.004
Form dia. (min.) Dfi 27.6 1.09
Minor dia. Di 23.00+0.033 0.90550+0.0013
Space width (circular) Lo 4.308±0.020 0.1696±0.0008
Tooth thickness (circular) So 2.341 0.09217
Fillet radius Rmin. 0.2 0.008
Max. mea l 17.620 +0.15 0.7000–0.006
surement
between pins*
Pin dia. d 4.835±0.001 0.1903±0.00004
* Finished dimensions (when hardened).
Rmin
Lo
So
Dri
Di
l Dfi
d D
151-874.10
If a drain line is fitted to the attached component, it must be possible for oil to flow freely between motor
and attached component.
OMS
The drain line must be led to the tank in such a way that there is no risk of the motor and attached
component being drained of oil when at rest.
The maximum pressure in the drain line is limited by the attached component and its shaft seal.
OMT
Versions
OMT versions
Mounting Shaft Port size Europea US Drain Check valve Low High Main type
flange n version version connection pressure pressure designation
release release
Standard Cyl. 40 mm G 3/4 X Yes Yes OMT
flange
Cyl. 1.5 in 1 1/16-12 UN X Yes Yes OMT
Splined 1.5 in G 3/4 X Yes Yes OMT
1 1/16-12 UN X Yes Yes OMT
Tapered 45 mm G 3/4 X Yes Yes OMT
Tapered 1.75 in 1 1/16-12 UN X Yes Yes OMT
P.t.o. G 3/4 X Yes Yes OMT
Wheel Cyl. 40 mm G 3/4 X Yes Yes OMTW
Tapered 45 mm G 3/4 X Yes Yes OMTW
Tapered 1.75 in 1 1/16-12 UN X Yes Yes OMTW
Brake-wheel Wheel bolt flange G 3/4 X Yes No X OMT FX
Thread hole flange G 3/4 X Yes No X OMT FX
Brake- Cyl. 40 mm G 3/4 X Yes No X OMT FL
standard
Splined 1.5 in G 3/4 X Yes No X OMT FL
Cyl. 40 mm G 3/4 X Yes No X OMT FH
Splined 1.5 in G 3/4 X Yes No X OMT FH
Short No output shaft G 3/4 X Yes Yes OMTS
Features
Features available (options):
• Speed sensor
• Motor with tacho connection
• Viton shaft seal
• Painted
• Ultra short
Code numbers
OMT
Ordering
Add the four digit prefix “151B” to the four digit numbers from the chart for complete code number.
Example:
151B3002 for an OMT 250 with standard flange, cyl. 40 mm shaft and port size G 3/4.
Technical data
151-320.10
OMT
151-1405.10
P P
psi bar
1500
100
90
1200
80
70
900
60
50
600 40
30
300 20
10
0 0
0 100 200 300 400 500 600 700 800 max. min-1
(rpm)
151-1674.10
– – – – Intermittent operation: the permissible values may occur for max. 10% of every minute.
Continuous operation
Technical data for OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH
Type OMT OMT OMT OMT OMT OMT
OMTW OMTW OMTW OMTW OMTW OMTW
OMTS OMTS OMTS OMTS OMTS OMTS
OMT FX OMT FX OMT FX OMT FX OMT FX OMT FX
OMT FL OMT FL OMT FL OMT FL OMT FL OMT FL
OMT FH OMT FH OMT FH OMT FH OMT FH OMT FH
OMT
Technical data for OMT, OMTW, OMTS, OMT FX OMT FL and OMT FH (continued)
Type OMT OMT OMT OMT OMT OMT
OMTW OMTW OMTW OMTW OMTW OMTW
OMTS OMTS OMTS OMTS OMTS OMTS
OMT FX OMT FX OMT FX OMT FX OMT FX OMT FX
OMT FL OMT FL OMT FL OMT FL OMT FL OMT FL
OMT FH OMT FH OMT FH OMT FH OMT FH OMT FH
1) Intermittent operation: the permissible values may occur for max. 10% of every minute.
2) Peak load: the permissible values may occur for max. 1% of every minute.
For maximum permissible combination of flow and pressure, see function diagram for actual motor.
OMT
Brake motors
Type Maximum presssure in Holding torque4) Brake-release pressure3) Maximum pressure in
drain line3) brake line
OMT FX, OMT FL 5 bar 1200 Nm 12 bar 30 bar
[70 psi] [10620 lbf·in] [170 psi] [440 psi]
OMT FH 5 bar 1200 Nm 30 bar 280 bar
[70 psi] [10620 lbf·in] [440 psi] [4060 psi]
1) Intermittent operation: the permissible values may occur for maximum 10% of every minute.
2) Peak load: The permissible values may occur for maximum 1% of every minute.
3) Brake motors must always have a drain line. The brake-release pressure is the difference between the
pressure in the brake line and the pressure in the drain line.
4) For the supply of motors with holding torques higher than those stated, please contact the Danfoss
sales organization.
For maximum permissible combination of flow and pressure, see function diagram for actual motor.
∆p ∆p
psi bar
16
200 14
12
150 10
8
100
6
4
50
2
0 0 Q
0 20 40 60 80 100 120 140 l/min
Q
0 4 8 12 16 20 24 28 32 36 US gal/min
151-1409.10
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]
Maximum oil flow in the drain line at a return pressure less than 5-10 bar [75-150 psi]
Pressure drop Viscosity Oil flow in drain line
bar [psi] mm2/s [SUS] l/min [US gal/min]
140 20 [100] 2.5 [0.66]
[2030]
35 [165] 1.5 [0.40]
210 20 [100] 5.0 [1.32]
[3050]
35 [165] 3.0 [0.79]
OMT
Direction of shaft rotation
B A B A
151-1050.10
Mounting flange:
Standard
Shaft:
All shaft types
Prad. Prad.
lbf N
14000
60000
0
- +
12000 Pmax. =10000 N
50000 =2248 lbf
10000
40000
8000
30000
6000
20000
4000
2000 10000
0 0
-60 -40 -20 0 20 40 60 80 100 120 140 mm
151-1967.10
Mounting flange:
Wheel
Shaft:
All shaft types
OMT
Prad. Prad.
lbf N
14000
60000
0 Pmax. =10000 N
12000 - +
=2248 lbf
50000
10000
40000
8000
30000
6000
20000
4000
2000 10000
0 0
0 20 40 60 80 100 120 140 160 mm
0 1 2 3 4 5 6 in
151-1970.10
The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of the distance from
the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at 100 min-1) at rated
output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows maximum radial shaft load. Any shaft load exceeding the values shown in the
curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing
dimensioning" in the technical information "General Orbital motors" 520L0232.
Mounting flange:
Brake-wheel
Shaft:
All shaft types
OMT
Prad. Prad.
lbf N
5500 25000
0 Pmax. =5000 N
5000 - + =1124 lbf
4500 20000
4000 Pmax. =7000 N
=1574 lbf
3500 15000
3000
2500
10000
2000
1500
5000
1000
500
0 0
0 20 40 60 80 100 120 140 mm
151-1966.10
Mounting flange:
Brake-standard
Shaft:
All shaft types
Prad. Prad.
lbf N
14000
60000
0
- +
12000 Pmax. =10000 N
50000 =2248 lbf
10000
40000
8000
30000
6000
20000
4000
2000 10000
0 0
-80 -60 -40 -20 0 20 40 60 80 100 120 mm
151-1968.10
The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of the distance from
the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at 100 min-1) at rated
output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown in the curve will
involve a risk of breakage.
OMT
Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing
dimensioning" in the technical information "General Orbital motors" 520L0232.
Function diagrams
Continuous range
Intermittent range (maximum 10% operation every minute)
OMT 160
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
Q=125 l/min
[33.0 US gal/min]
lbf• in Nm
5500
600
5000
550 ∆ p=240 bar
3480 psi
4500 500 N=35kW
151-493.10
OMT 200
lbf• in Nm
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=150 l/min
[39.6 US gal/min]
750
6500
700
6000 ∆ p=240 bar
650 35kW N=40kW 3480 psi
5500
600 30kW
5000 550 200 bar
25kW 2900 psi
4500 500 35hp
20kW 40hp
4000 450 160 bar
15kW 25hp 30hp 2320 psi
3500 400
10kW 15hp 20hp 87%
3000 350
10hp 120 bar
300
2500 N=5kW η t =88% 1740 psi
250 85%
2000
200 5hp 80 bar
1500 1160 psi
150
80%
1000 100
η t =70% ∆ p= 40 bar
500 50
580 psi
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 700 750 min-1
(rpm)
151-494.10
OMT
OMT 250
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=150 l/min
[39.6 US gal/min]
lbf• in Nm
9000
8000 900
∆ p=240 bar
7000 800 3480 psi
35kW N=40kW
30kW
700 200 bar
6000
40hp 2900 psi
600 25kW 35hp
5000
20kW 30hp 160 bar
500 2320 psi
4000 15kW 25hp
400 20hp 120 bar
15hp 1740 psi
10kW
3000 η t =87%
300
N=5kW 80 bar
2000 10hp 85%
200 1160 psi
5hp 80%
1000 100 ∆ p= 40 bar
η t =70% 580 psi
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 min-1
(rpm)
151-495.10
OMT 315
lbf• in Nm
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
60 l/min
[15.9 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=150 l/min
[39.6 US gal/min]
11000
1200
10000
1100 ∆ p=240 bar
9000 3480 psi
1000 35kW N=40kW
8000 900 200 bar
30kW
800 25kW 2900 psi
7000
40hp
700 20hp 20kW 160 bar
6000 15kW 30hp 35hp 2320 psi
15hp 25hp
600
5000
120 bar
500 10kW
4000 1740 psi
10hp
400
3000 5hp N=5kW 80 bar
300 87%
η t =88% 1160 psi
2000
200
1000
85% 80% ∆ p= 40 bar
100 580 psi
η t =70%
0 0
0 50 100 150 200 250 300 350 400 450 500 min-1
(rpm)
151-869.10
OMT
OMT 400
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=150 l/min
[39.6 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
12000
1300
11000
1200 ∆ p=210 bar
10000 3050 psi
1100
9000 1000 180 bar
2610 psi
8000 900 N=30kW
25kW 150 bar
7000 800 2180 psi
20kW
700
6000 15kW 120 bar
10kW 25hp 30hp 1740 psi
600 10hp
5000 87%
20hp
500
4000 5kW
η t =89% 15hp 90 bar
5hp 1300 psi
400 85%
3000
300 60 bar
2.5hp 80% 870 psi
2000 200 N=2.5kW
0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 min-1
(rpm)
151-1058.10
OMT 500
Q=10 l/min
[2.6 US gal/min]
20 l/min
[5.3 US gal/min]
40 l/min
[10.6 US gal/min]
80 l/min
[21.1 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=150 l/min
[39.6 US gal/min]
60 l/min
[15.9 US gal/min]
lbf• in Nm
1500
12500
∆ p=180 bar
1250 2610 psi
0 25 50 75 100 125 150 175 200 225 250 275 300 min-1
(rpm)
151-1116.10
Intermittent pressure drop and oil flow must not occur simultaneously.
OMT
Shaft version
82 [3.23]
26 [1.02]
9.5 [0.374]
45˚
R0.5 [0.020] M12
A-A
A
Ø40.018 [1.5755]
Ø40.002 [1.5749]
43.00 [1.693]
42.71 [1.681]
Ø45 [1.77]
A C
82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]
45˚
R0.5 [0.020] 3/8 -16 UNC
A-A
A
Ø38.10 [1.500]
Ø38.05 [1.498]
42.40 [1.669]
42.14 [1.659]
Ø45 [1.77]
A D
57.5 [2.264] 11.5 [0.453]
56.9 [2.240] 9.3 [0.366]
9.545 [0.3758]
9.525 [0.3750]
151-1032.10
OMT
82 [3.23]
26 [1.02]
9.5 [0.374]
45˚
R0.5 [0.020] M12
A-A
A
Ø38.100 [1.5000]
Ø38.075 [1.4990]
Ø45 [1.77]
A
58 [2.28]
56 [2.20]
82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]
45˚
R0.5 [0.020] 3/8 -16 UNC
A A-A
Ø38.100 [1.5000]
Ø38.075 [1.4990]
Ø45 [1.77]
A
58 [2.28]
56 [2.20]
151-1916.10
OMT
I A-A K L
16 [0.63] A-A
H
A A
Ø56 [2.20]
Ø45 [1.77]
Ø4 [0.16]
Ø6 [0.24]
Ø7 [0.28]
Ø45 [1.77]
M30x2
24.15 [0.951]
23.95 [0.943]
E F
5.71 [0.225]
5.61 [0.221]
A J A M
34 [1.34] 4 [0.16] 32.1 [1.264]
12.000 [0.4724] 31.5 [1.240]
54 [2.13] 22 [0.87] 59.00 [2.323] 11.150 [0.4390]
11.957 [0.4707]
57.80 [2.276] 11.130 [0.4382]
82 [3.23]
4.5 [0.177]
80.8 [3.181]
80.0 [3.150]
102 [4.02]
45˚ R0.5 [0.020] R6.7 [0.267]
R5 [0.20]
60˚ A-A
A
8.6 3 [0.3
8.5
4[
Ø34.85 [1.372]
Ø34.73 [1.367]
0.3 36]
29.5 [1.161]
29.3 [1.154]
Ø45 [1.77]
40
G
]
28.14 [1.108]**
A 7 [0.28]
38.25 [1.506] 27.89 [1.098]
151-1917.10
77 [3.03] 37.75 [1.486]
75 [2.95]
OMT
Port thread versions
B
A Ø41.5 [1.634]
Ø41.0 [1.614]
E F
min. 18 [0.67]
min. 19 [0.75]
C D
G H
min. 13 [0.51]
min. 12 [0.47]
151-1977.11
OMT
Dimensions
L3
22.4 [0.882]
R1.6 [0.063]
9 [0.35]
32 [1.26]
31 [1.22]
60 [2.36]
72 [2.83]
18 [0.71]
64 [2.52]
L2
13.0 [0.512]
12.0 [0.472]
L
L1
D
C
13.0 [0.512]
12.0 [0.472]
max. 69 [2.72]
13.0 [0.512]
12.0 [0.472]
23.6 [0.929]
22.4 [0.882]
13.0 [0.512]
12.0 [0.472]
28 ]
[6. .315
3]
59 [6
Ø1 60.4
.6
R12 [0.47]
Ø1
151-889.11
C: Drain connection D: M10; 10 mm [0.39 in] deep E: G 3⁄4; 17 mm [0.67 in] deep
G 1⁄4; 12 mm [0.47 in] deep
OMT
OMT
Standard flange—US version
Ø127.00 [5.000]
Ø126.95 [4.998]
Ø123.8 [4.874]
Ø122.2 [4.811]
Ø86.5 [3.406]
Ø85.5 [3.366]
33.15 [1.305]
30.85 [1.215]
L3
22.4 [0.882]
R0.8 [0.003]
9 [0.35]
31 [1.22]
60 [2.36]
73.7 [2.902]
71.5 [2.815]
18 [0.71]
64.5 [2.539]
63.5 [2.500]
L2
L
L1
max. 69 [2.72]
23.6 [0.929]
22.4 [0.882]
35 ]
[6. .390
8]
61 3 [6
R12.5 [0.492]
Ø1 62.
.5
Ø1
151-889.11.22
C: Drain connection 9⁄16 - 18 UNF; 13 mm [0.51 in] deep O-ring boss port
D: 1 1⁄16 - 12 UN; 19 mm [0.75 in] deep O-ring boss port
OMT
OMT
Wheel—European version
Ø172.000 [6.7717]
Ø171.937 [6.7692]
Ø160.000 [6.2992]
Ø159.937 [6.2967]
Ø126.25 [4.970]
Ø123.75 [4.872]
Ø123.8 [4.874]
Ø122.2 [4.811]
Ø73 [2.87]
Ø71 [2.80]
82 [3.23]
2 [0.08]x45˚
98.2 [3.866]
99 [3.90]
90.3 [3.555]
78.2 [3.079]
R1.2 [0.047]
45˚
7 [0.28]
8 [0.31]
18 [0.71]
13.0 [0.512]
12.0 [0.472]
L1
L2
R1.2 [0.047]
4 [0.16]
13.0 [0.512]
12.0 [0.472]
C
L
max. 69 [2.72]
D
13.0 [0.512]
12.0 [0.472]
23.6 [0.929]
22.4 [0.882]
13.0 [0.512]
12.0 [0.472]
85 ]
[7. .890
8]
99 [7
Ø1 00.4
.6
Ø2
R16 [0.63]
151-897.12
C: Drain connection D: M10; 10 mm [0.39 in] deep E: G 3⁄4; 17 mm [0.67 in] deep
G 1⁄4; 12 mm [0.47 in] deep
OMT
OMT
Wheel—US version
Ø172.000 [6.7717]
Ø171.937 [6.7692]
Ø160.000 [6.2992]
Ø159.937 [6.2967]
Ø126.25 [4.970]
Ø123.75 [4.872]
Ø123.8 [4.874]
Ø122.2 [4.811]
Ø73 [2.87]
Ø71 [2.80]
80.8 [3.181]
80.0 [3.150]
2 [0.08]x45˚
102.1 [4.020]
99.1 [3.902]
98.2 [3.866]
90.3 [3.555]
78.6 [3.094]
77.5 [3.051]
R1.2 [0.047]
45˚
7 [0.28]
7 [0.28]
18 [0.71]
L1
L2
3.5 [0.138]
R1.2 [0.047]
C
L
max. 69 [2.72]
23.6 [0.929]
22.4 [0.882]
85 ]
[7. .890
8]
99 4 [7
Ø1 00.
.6
Ø2
R16 [0.63]
151-897.11.22
OMT
OMT
Brake-wheel—European version
m
ax
Ø
.2
Ø1 200
32
75 [2.95]
99 .4
[9
.6 [7.8
.1
F
3]
[7 9
.8 0]
58
]
71 [2.80]
C
Ø22 [0.87]
67 [2.64]
Ø201 [7.91]
Ø180.00 [7.087] Ø120.0 [4.724]
12.2 [0.480]
11.8 [0.465]
13.2 [0.520]
Ø179.6 [7.074] 12.8 [0.504]
5.2 [0.205]
4.8 [0.189]
4.2 [0.165]
3.8 [0.150]
Ø119.6 [4.709]
H Ø95.8 [3.772] Ø76.0 [2.992]
Ø95.6 [3.764] Ø75.8 [2.984]
G
35 [1.38]
111.4 [4.386]
110.6 [4.354]
115.4 [4.543]
114.6 [4.512]
10.2 [0.402]
9.8 [0.386]
7.2 [0.283]
6.8 [0.268]
L max. 1
L max. 2
L1
E D
L2
I
13 [0.51]
12 [0.47]
11.1 [0.437]
10.9 [0.429]
23.3 [0.917]
22.7 [0.894]
13 [0.51]
12 [0.47]
23.1 [0.909]
22.9 [0.902]
20.3 [0.799] 20.3 [0.799]
19.7 [0.776] 19.7 [0.776]
22.1 [0.870] 22.1 [0.870]
21.1 [0.831] 21.1 [0.831]
100 [3.94]
128 [5.04]
Ø172.00 [6.772]
Ø171.94 [6.769]
10x36˚
5x72˚
4x90˚
151-1443.11
C: Brake-release port G 1/4; 12 mm D: Drain connection G 1/4; 12 mm E: G 3/4; 17 mm [0.67 in] deep F: 4 × M12; 27 mm [1.06 in] deep
[0.47 in] deep (BS/ISO 228/1) [0.47 in] deep
G: 10 × M12 H: Wheel bolts 5 × M14 × 1.5 I: M10; 10 mm [0.39 in] deep
OMT
OMT
Brake-standard—European version
Ø125.000 [4.9213]
Ø124.937 [4.9188]
Ø123.5 [4.862]
Ø122.5 [4.823]
Ø86.2 [3.406]
12 [0.47]
Ø85.5 [3.366]
31.5 [1.240]
82 [3.23]
R1.6 [0.063]
12 [0.47]
18 [0.71]
60 [2.36]
32 [1.26]
104 [4.09]
85.8 [3.378]
90.5 [3.563]
L2
E
L
D
F
L1
13.0 [0.512]
12.0 [0.472]
C
23.6 [0.929]
22.4 [0.882]
13.0 [0.512]
12.0 [0.472]
13.0 [0.512]
12.0 [0.472]
13.0 [0.512]
12.0 [0.472]
151-1453.10
C: G 3/4; 17 mm [0.67 in] D: Drain connection G 3/8; E: Brake-release port G 1/4; F: M10; 10 mm [0.39 in]
deep (BS/ISO 228/1) 14 mm [0.55 in] deep 12 mm [0.47 in] deep deep
OMT
Short—European version
Ø124.937 [4.9188]
8 [0.31]
R1 [0.04]
Ø14 [0.55]
22 [0.87]
31 [1.22]
18 [0.71]
L2
13 [0.512]
12 [0.472]
L1
8 [0.31]
C
13 [0.512]
12 [0.472]
L
max. 69 [2.72]
13 [0.512]
12 [0.472]
D
23.6 [0.926]
22.4 [0.882]
13 [0.512]
12 [0.472]
Ø16
Ø15 0.4 [6.3
9.6 1
[6.2 5]
83]
Ø6 [0.24]
151-898.11
OMT
OMTS
Installation
The cardan shaft of the OMTS motor acts as an “output shaft”. Because of the movement of the shaft, no
seal can be fitted at the shaft output.
Internal oil leakage from the motor will therefore flow into the attached component.
During start and operation it is important that the spline connection and the bearings in the attached
component receive oil and are adequately lubricated. To ensure that the spline connection receives
sufficient oil, a conical sealing ring between the shaft of the attached component and the motor
intermediate plate is recommended. This method is used in the OMT.
The conical sealing ring (code. no. 633B9022) is supplied with the motor.
To ensure that oil runs to the bearings and other parts of the attached component, the stop plate must
have a hole in it (see fig. below).
We recommend an O-ring between motor and attached component. The O-ring (code no. 151B1040) is
supplied with the motor. If motor and attached component have been separated, remember to refill
before starting up. Fill the oil through the drain connection.
K 0.25 [0.010]
Ø88.5 [3.484]
Ø87.5 [3.445]
K 0.1˚
Ø125.063 [4.9237]
Ø125.000 [4.9212]
Ø133.0 [5.236]
Ø132.6 [5.220]
min. Ø55 [2.17]
Ø53.5 [2.106]
Ø53.5 [2.098]
min. Ø6 [0.24]
Ø63.5 [2.500]
Ø62.5 [2.461]
K
39.5 [1.555]
38.5 [1.516]
Ø51.5 [2.028]
Ø50.5 [1.988]
G
H D
E
2.5 [0.098] min. 5 [0.2] 8.2 [0.323]
1.5 [0.059] 7.8 [0.307]
18.5 [0.728]
25.5 [1.004] 17.5 [0.689]
24.5 [0.965]
11.4 [0.449] 30 [1.181]
11.0 [0.433] 29 [1.142]
46.3 [1.823]
45.7 [1.799]
69.4 [2.732]
68.6 [2.701]
151-452.10
OMT
Material:
Case hardening steel with a tensile strength corresponding at least to 20 MoCr4 (900 N/mm2) or SAE
8620.
Hardening specification:
• On the surface: HV = 750 ± 50
• 0.7 ± 0.2 mm under the surface: HV = 560
Internal involute spline data; Standard ANS B92.1-1970, class 5 (corrected m · X = 1; m = 2.1166)
Flat root side fit mm in
Number of teeth z 16 16
Pitch DP 12/24 12/24
Pressure angle 30° 30°
Pitch dia. D 33.8656 1.3333
Major dia. Dri 38.40 +0.4 1.51180+0.0157
Form dia. (min.) Dfi 37.6 1.4803
Minor dia. Di 32.1500+ 0.04 1.26570+ 0.00157
Space width (circular) Lo 4.516±0.037 0.1777±0.0014
Tooth thickness (circular) So 2.170 0.0854
Fillet radius Rmin. 0.5 0.02
Max. measurement between pins* l 26.90 + 0.1 1.0590+0.004
Pin dia. d 4.834±0.001 0.1903±0.00004
* Finished dimensions (when hardened).
OMT
Rmin
Lo
So
l d
Dri
Di
Dfi
D
151-455.10
If a drain line is fitted to the attached component, it must be possible for oil to flow freely between motor
and attached component.
The drain line must be led to the tank in such a way that there is no risk of the motor and attached
component being drained of oil when at rest.
The maximum pressure in the drain line is limited by the attached component and its shaft seal.
OMV
Versions
OMV versions
Mounting Shaft Port size European US version Drain Check valve Main type
flange version connection designation
Standard flange Cyl. 50 mm G1 X Yes Yes OMV
Cyl. 2.25 in 1 5/16-12 UN X Yes Yes OMV
Splined 2.125 in G1 X Yes Yes OMV
1 5/16-12 UN X Yes Yes OMV
Tapered 60 mm G1 X Yes Yes OMV
Tapered 2.25 in 1 5/16-12 UN X Yes Yes OMV
SAE-C flange Cyl. 2.25 in 1 5/16-12 UN X Yes Yes OMV
Splined 2.125 in 1 5/16-12 UN X Yes Yes OMV
Wheel Cyl. 50 mm G1 X Yes Yes OMVW
Tapered 60 mm G1 X Yes Yes OMVW
Tapered 2.25 in 1 5/16-12 UN X Yes Yes OMVW
Short No output shaft G1 X Yes Yes OMVS
Features
Features available (options):
• Speed sensor
• Motor with tacho connection
• Viton shaft seal
• Painted
• Ultra short
Code numbers
OMV
Ordering
Add the four digit prefix “151B” to the four digit numbers from the chart for complete code number.
Example:
151B3101 for an OMV 400 with standard flange, cyl. 50 mm shaft and port size G 1.
Orders will not be accepted without the four digit prefix.
Technical data
1) Intermittent operation: the permissible values may occur for max. 10% of every minute.
2) Peak load: The permissible values may occur for max. 1% of every minute.
For max. permissible combination of flow and pressure, see function diagram for actual motor.
OMV
151-320.10
P P
psi bar
1500
100
90
1200
80
70
900
60
50
600 40
30
300 20
10
0 0
0 100 200 300 400 500 600 700 800 max. min-1
(rpm)
151-1674.10
– – – – Intermittent operation: the permissible values may occur for max. 10% of every minute.
Continuous operation
∆p ∆p
psi bar
16
200 14
12
150 10
8
100
6
4
50
2
0 0 Q
0 20 40 60 80 100 120 140 160 180 200 l/min
Q
0 5 10 15 20 25 30 35 40 45 50 US gal/min
151-1410.10
The curve applies to an unloaded motor shaft and an oil viscosity of 35 mm2/s [165 SUS]
OMV
Oil flow in drain line
Maximum oil flow in the drain line at a return pressure less than 5-10 bar [75-150 psi]
Pressure drop Viscosity Oil flow in drain line
bar [psi] mm2/s [SUS] l/min [US gal/min]
140 [2030] 20 [100] 3.0 [0.79]
35 [165] 2.0 [0.53]
210 [3050] 20 [100] 6.0 [1.59]
35 [165] 4.0 [1.06]
Mounting flange:
Standard
Shaft:
All shaft types
Prad. Prad.
lbf N
16000 70000
0 Pmax. =15000 N
- +
14000 =3372 lbf
60000
12000
50000
10000
40000
8000
30000
6000
20000
4000
2000 10000
0 0
-80 -60 -40 -20 0 20 40 60 80 100 120 mm
151-1973.10
OMV
Mounting flange:
Wheel
Shaft:
All shaft types
Prad. Prad.
lbf N
16000 70000
0 Pmax. =15000 N
- +
14000 =3372 lbf
60000
12000
50000
10000
40000
8000
30000
6000
20000
4000
2000 10000
0 0
0 20 40 60 80 100 120 140 160 180 200 mm
0 1 2 3 4 5 6 7 in
151-1969.10
The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of the distance from
the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at 100 min-1) at rated
output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows maximum radial shaft load. Any shaft load exceeding the values shown in the
curve will involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing
dimensioning" in the technical information "General Orbital motors" 520L0232.
Mounting flange:
SAE-C
Shaft:
All shaft types
OMV
Prad. Prad.
lbf N
14000
60000
0 Pmax. =10000 N
12000 A B
- +
=2248 lbf
50000
10000 B
40000
8000 A
30000
6000
20000
4000
2000 10000
0 0
-80 -60 -40 -20 0 20 40 60 80 100 120 mm
151-1965.10
The output shaft runs in tapered roller bearings that permit high axial and radial forces.
The permissible radial load on the shaft is shown for an axial load of 0 N as a function of the distance from
the mounting flange to the point of load application.
The curve is based on B10 bearing life (2000 hours or 12,000,000 shaft revolutions at 100 min-1) at rated
output torque, when mineral-based hydraulic oil with a sufficient content of anti-wear additives, is used.
For 3,000,000 shaft revolutions or 500 hours – increase these shaft loads with 52%.
The dash curve shows max. radial shaft load. Any shaft load exceeding the values shown in the curve will
involve a risk of breakage.
Bearing life calculations can be made using the explanation and formula provided in the chapter "Bearing
dimensioning" in the technical information "General Orbital motors" 520L0232.
Function diagrams
Continuous range
Intermittent range (maximum 10% operation every minute)
OMV
OMV 315
Q=10 l/min
[2.6 US gal/min]
25 l/min
[6.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
160 l/min
[42.2 US gal/min]
Q=200 l/min
[52.8 US gal/min]
lbf• in Nm
11000
1200
10000
1100
∆ p=240 bar
9000 1000 3480 psi
8000 N=50kW
900
200 bar
7000 800 2900 psi
170 bar
40kW
700 30kW 2540 psi
6000 30hp
50hp
600 140 bar
5000 20kW
20hp 40hp 2030 psi
500
4000 10kW η t =87%
N=5kW 105 bar
400 10hp
5hp 1520 psi
3000 85%
300
70 bar
2000 1020 psi
200
80%
1000 100 η t =70% ∆ p= 35 bar
510 psi
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 650 min-1
(rpm)
151-870.10
OMV 400
Q=10 l/min
[2.6 US gal/min]
25 l/min
[6.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
175 l/min
[46.2 US gal/min]
200 l/min
[52.8 US gal/min]
Q=240 l/min
[63.4 US gal/min]
lbf• in Nm
14000 1600
1400
12000 ∆ p=240 bar
3480 psi
1200
10000
200 bar
1000 N=50kW 2900 psi
30hp 50hp 175 bar
8000
40hp 40kW 2540 psi
800
20hp 140 bar
6000 30kW 2030 psi
600
η t =88% 87%
105 bar
10hp 20kW
4000 85% 1520 psi
400
5hp 10kW 70 bar
N=5kW 80% 1020 psi
2000 200
η t =70% ∆ p= 35 bar
510 psi
0 0
0 50 100 150 200 250 300 350 400 450 500 550 600 min-1
(rpm)
151-871.10
OMV
OMV 500
lbf• in Nm
Q=10 l/min
[2.6 US gal/min]
25 l/min
[6.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
150 l/min
[39.6 US gal/min]
175 l/min
[46.2 US gal/min]
200 l/min
[52.8 US gal/min]
Q=240 l/min
[63.4 US gal/min]
16000 1800
0 50 100 150 200 250 300 350 400 450 500 min-1
(rpm)
151-872.10
OMV 630
Q=10 l/min
[2.6 US gal/min]
25 l/min
[6.6 US gal/min]
50 l/min
[13.2 US gal/min]
75 l/min
[19.8 US gal/min]
100 l/min
[26.4 US gal/min]
125 l/min
[33.0 US gal/min]
Q=240 l/min
[63.4 US gal/min]
150 l/min
[39.6 US gal/min]
175 l/min
[46.2 US gal/min]
200 l/min
[52.8 US gal/min]
lbf• in Nm
17500 2000
1750
∆ p=210 bar
15000 N=60kW 3050 psi
1000 40hp
20kW 120 bar
η t =89% 30hp 1740 psi
7500
750 10kW
87% 90 bar
N=5kW 20hp 1300 psi
5000
500
85% 60 bar
80% 10hp 870 psi
2500 250
η t =70% 5hp ∆ p= 30 bar
440 psi
0 0
0 25 50 75 100 125 150 175 200 225 250 275 300 325 350 375 400 min-1
(rpm)
151-879.10
OMV
OMV 800
lbf•in Nm
Q = 10 l/min
2.6 US gal/min
25 l/min
6.6 US gal/min
50 l/min
13.2 US gal/min
75 l/min
19.8 US gal/min
100 l/min
26.4 US gal/min
125 l/min
33.0 US gal/min
150 l/min
39.6 US gal/min
175 l/min
46.2 US gal/min
200 l/min
52.8 US gal/min
Q = 240 l/min
63.4 US gal/min
20000 2250
0 25 50 75 100 125 150 175 200 225 250 275 300 min-1
(rpm)
P301 250
Intermittent pressure drop and oil flow must not occur simultaneously.
OMV
Shaft version
82 [3.23]
26 [1.02]
9.5 [0.374]
Ø50.018 [1.9692]
Ø50.002 [1.9686]
Ø60 [2.36]
53.5 [2.106]
53.2 [2.094]
A
A
70.5 [2.776] 5.5 [0.217]
4.5 [0.177] 14.000 [0.5512]
70.0 [2.756]
13.957 [0.5495]
79 [3.11] D
82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]
60˚
R0.5 [0.020] 3/8 -16 UNC A-A
A
Ø57.15 [2.250]
Ø57.10 [2.248]
Ø60 [2.36]
62.92 [2.477]
62.66 [2.467]
A
13.1 [0.516]
10.9 [0.429]
12.73 [0.501]
12.70 [0.500]
E
57.5 [2.264]
56.9 [2.240]
99.2 [3.906]
98.8 [3.890]
min. 26 [1.02]
½ -20 UNF
60˚
R0.5 [0.020] A-A
A
57.15 [2.250]
57.10 [2.248]
Ø60 [2.36]
62.93 [2.478]
62.66 [2.467]
A
70.4 [2.772]
70.2 [2.763] 12.73 [0.501]
12.70 [0.500] F
151-878.12
A Cylindrical 50 mm shaft B Cylindrical 2.25 in shaft for OMV with C Cylindrical 2.25 in shaft for OMV with
standard mounting flange mounting flange SAE-C
D Parallel key
E Parallel key F Parallel key
A14 × 9 × 70; DIN 6885
1/2 × 1/2 × 21/ 4 in; B.S. 46 1/2 × 1/2 × 21/4 in; B.S. 46
Keyway deviates from standard
Keyway deviates from standard Keyway deviates from standard
OMV
82[3.23]
26 [1.02]
53.975 [2.1250]
53.950 [2.1240]
Ø60 [2.36]
A
58 [2.28]
56 [2.20]
82.2 [3.236]
81.8 [3.220]
min. 20 [0.78]
45˚
3/8 -16 UNC
R0.5 [0.020] A-A
A
Ø53.975 [2.1250]
Ø53.950 [2.1240]
Ø60 [2.36]
A
57 [2.24]
55 [2.17]
76.9 [3.028]
76.5 [3.011]
min. 26 [1.02]
½ -20 UNF
30˚ R0.5 [0.020]
A-A
A
Ø53.972 [2.1249]
Ø53.954 [2.1242]
Ø60 [2.36]
A
56.3 [2.217]
55.3 [2.177]
151-1918.10
OMV
23 [0.91]
A-A
7 [0.28]
I J
A
M42x3 [0.12]
Ø60 [2.36]
Ø78 [3.07]
Ø8 [0.31]
Ø9 [0.35]
G
32.25 [1.270]
32.05 [1.262]
A
40.5 [1.594]
6 [0.24]
40.0 [1.575]
16.000 [0.6299] K
70 [2.76] 15.957 [0.6282]
105 [4.13]
16 [0.63]
45˚
4.5 [0.177]
L M A-A
A
Ø57.20 [2.252]
Ø57.10 [2.248]
Ø60 [2.36]
Ø4 [0.16]
H
7.29 [0.287]*
7.19 [0.283]
151-1919.10
OMV
B
A Ø41.5 [1.634]
Ø41.0 [1.614]
E F
min. 18 [0.67]
min. 19 [0.75]
C D
G H
min. 13 [0.51]
min. 12 [0.47]
151-1977.11
OMV
Dimensions
Ø160.000 [6.2992]
Ø159.937 [6.2967]
Ø146.4 [5.764]
Ø145.0 [5.710]
Ø83 [3.27]
L3
2 [0.08]x45˚
11 [0.43]
39.4 [1.551]
38.6 [1.520]
40 [1.57]
33˚
R1.6 [0.063]
60 [2.36]
20 [0.79]
L2
C 69 [2.72] 8 [0.31]
E
L1
14.0 [0.551]
13.0 [0.512]
L
14.0 [0.551]
13.0 [0.512]
max. 76 [2.99]
14.0 [0.551]
13.0 [0.512]
24.6 [0.969]
23.4 [0.921]
14.0 [0.551]
13.0 [0.512]
0]
89
[7. 858]
.4 .
00 [7 max. 179 [7.05]
Ø2 99.6
Ø1
Ø18 [0.71]
R16 [0.63] max. 179 [7.05]
151-890.11
OMV
OMV
Standard flange—US version
Ø160.000 [6.2992]
Ø159.937 [6.2967]
Ø146.3 [5.760]
Ø145.7 [5.736]
Ø90 [3.54]
Ø88 [3.46]
L3
2 [0.08]x45˚
11 [0.43]
39.4 [1.551]
38.6 [1.520]
40 [1.57]
33˚
R1.6 [0.063]
60 [2.36]
20 [0.79]
77 [3.03]
L2
C 69 [2.72]
D
L1
L
max. 76 [2.99]
24.6 [0.969]
23.4 [0.921]
0]
89
[7. 858]
.4 .
00 .6 [7
Ø18 [0.71]
R16 [0.63] max. 179 [7.05]
151-890.11.22
C: Drain connection 9⁄16 - 18 UNF; 13 mm [0.51 in] deep O-ring boss port
D: 1 5⁄16 - 12 UN; 19 mm [0.75 in] deep O-ring boss port
OMV
OMV
SAE-C flange—US version
Ø127.00 [5.000]
Ø126.95 [4.998]
L3
16.1 [0.634]
13.7 [0.539]
13.8 [0.543]
13.2 [0.520]
21.0 [0.827]
19.6 [0.772]
85.5 [3.366]
C 71.0 [2.795]
L2
81.5 [3.209]
L
L1
24.0 [0.945]
max. 76 [2.99]
D
0]
39
[6. 358]
.3
62 [6.
Ø1 61.5
max. 147 [5.79]
Ø1
Ø17.7 [0.697]
Ø17.3 [0.681]
max. 147 [5.79]
151-1485.10
C: Drain connection 9⁄16 - 18 UNF; 13 mm [0.51 in] deep O-ring boss port
D: 1 5⁄16 - 12 UN; 19 mm [0.75 in] deep O-ring boss port
OMV
OMV
Wheel—European version
Ø180.000 [7.0866]
Ø179.937 [7.0841]
Ø146.4 [5.764]
Ø145.0 [5.710]
Ø148.0 [5.827]
Ø83 [3.27] Ø147.9 [5.823]
2 [0.08]x45˚
L3
33˚
10 [0.39]
R1.2 [0.047]
22 [0.87]
8 [0.31]
20 [0.79]
R1.2 [0.047]
L1
3.6[0.142]
14.0 [0.551]
13.0 [0.512]
L2
14.0 [0.551]
13.0 [0.512]
C
L
max. 76 [2.99]
14.0 [0.551]
13.0 [0.512]
24.6 [0.969]
23.4 [0.921]
14.0 [0.551]
13.0 [0.512]
Ø194.000 [7.6378]
Ø193.928 [7.6350]
1]
83
[8. 07]
4.3 [8.8
Ø18 [0.71]
R16 [0.63] max. 198 [7.80]
151-899.11
OMV
OMV
Wheel—US version
Ø180.000 [7.0866]
Ø179.937 [7.0841]
Ø146.3 [5.760]
Ø145.7 [5.736]
Ø90 [3.54] Ø148.0 [5.827]
Ø88 [3.46] Ø147.9 [5.823]
100.4 [3.953]
2 [0.08]x45˚
99.6 [3.921]
33˚
10 [0.39]
R1.2 [0.047]
22 [0.87]
8 [0.31]
20 [0.79]
R1.2 [0.047]
L1
3.6 [0.142]
L2
C
L
max. 76 [2.99]
24.6 [0.969]
23.4 [0.921]
1]
83
[8. 807]
.3 .
24 [8
Ø18 [0.71]
R16 [0.63] max. 198 [7.80]
151-899.11.22
C: Drain connection 9⁄16 - 18 UNF; 13 mm [0.51 in] deep O-ring boss port
D: 1 5⁄16 - 12 UN; 19 mm [0.75 in] deep O-ring boss port
OMV
Short—European version
Ø140.000 [5.5118]
28 [1.10]
Ø139.937 [5.5093]
1 [0.04]x45˚
8 [0.31]
22 [0.87]
35 [1.38]
13.0 [0.512] 20 [0.79]
82 [3.23] 8 [0.31]
L2
L1
14.0 [0.551]
14.0 [0.551]
13.0 [0.512]
L
max. 76 [2.99]
14.0 [0.551]
13.0 [0.512]
24.6 [0.969]
23.4 [0.921]
14.0 [0.551]
13.0 [0.512]
Ø180
5]
28 [1.10]
.4
Ø179 [7.102]
.6 [7.0
71]
151-900.10
OMV
OMVS
Installation
The cardan shaft of the OMVS motor acts as an “output shaft”. Because of the movement of the shaft, no
seal can be fitted at the shaft output.
Internal oil leakage from the motor will therefore flow into the attached component.
During start and operation it is important that the spline connection and the bearings in the attached
component receive oil and are adequately lubricated. To ensure that the spline connection receives
sufficient oil, a conical sealing ring between the shaft of the attached component and the motor
intermediate plate is recommended. This method is used in the OMV.
The conical sealing ring (code. no. 633B9021) is supplied with the motor.
To ensure that oil runs to the bearings and other parts of the attached component, the stop plate must
have a hole in it (see fig. below).
We recommend an O-ring between motor and attached component. The O-ring (code no. 151B1041) is
supplied with the motor. If motor and attached component have been separated, remember to refill
before starting up. Fill the oil through the drain connection.
K 0.25 [0.010]
6 [0.24]
K 0.1˚ R
min. Ø60 [2.36]
4 [0.16]
Ø140.063 [5.5143]
Ø140.000 [5.5118]
Ø147.9 [5.823]
Ø147.7 [5.815]
Ø61.2 [2.409]
Ø61.0 [2.402]
Ø102 [4.02]
Ø100 [3.94]
Ø71 [2.80]
Ø69 [2.72]
K
Ø46.2 [1.819]
Ø45.8 [1.803]
Ø56.3 [2.217]
Ø55.5 [2.165]
G E
H max. 2 [0.08] min. 5 [0.2]
8.4 [0.331]
7.6 [0.299] 20.5 [0.807]
9.5 [0.374]
19.5 [0.768]
8.5 [0.335]
32.5 [1.280] 28.7 [1.130]
31.5 [1.240] 26.3 [1.035]
53.3 [1.098]
52.7 [2.075]
76.3 [3.004]
75.7 [2.980]
151-815.10
OMV
Material:
Case hardening steel with a tensile strength corresponding at least to 20 MoCr4 (900 N/mm2) or SAE
8620.
Hardening specification:
• On the surface: HV = 750 ± 50
• 0.7 ± 0.2 mm under the surface: HV = 560
Internal involute spline data; Standard ANS B92.1-1970, class 5 (corrected m · X = 1; m = 2.54)
Flat root side fit mm in
Number of teeth z 16 16
Pitch DP 10/20 10/20
Pressure angle 30° 30°
Pitch diameter D 40.640 1.6
Major diameter Dri 45.20+0.4 1.7800+0.016
Form diameter (minimum) Dfi 44.6 1.756
Minor diameter Di 38.50 + 0.039 1.5160+ 0.0015
Space width (circular) Lo 5.180±0.037 0.204±0 .0015
Tooth thickness (circular) So 2.835 0.1116
Fillet radius Rmin. 0.4 0.015
Maximum l 32.470+ 0.15 1.2780+0.006
measurement
between pins*
Pin diameter d 5.6±0.001 0.22±0.00004
* Finished dimensions (when hardened)
Rmin
Lo
So
Dri
Di
l d Dfi
D
151-816.10
OMV
Motor or attached component drain connection
Use the drain line when pressure in the return line exceeds the permissible pressure on the shaft seal of
the attached component.
Connect the drain line either at the:
• Motor drain connection
• Drain connection of the attached component
If a drain line is fitted to the attached component, it must be possible for oil to flow freely between motor
and attached component.
The drain line must be led to the tank in such a way that there is no risk of the motor and attached
component being drained of oil when at rest.
The maximum pressure in the drain line is limited by the attached component and its shaft seal.
Weight of motors
kg [lb]
151B2050 20.0 44.1
151B2051 20.5 45.2
151B2052 21.0 46.3
151B2053 22.0 48.5
151B2054 23.0 50.7
151B2055 24.0 52.9
151B2056 20.0 44.1
151B2057 20.5 45.2
151B2058 21.0 46.3
151B2059 22.0 48.5
151B2060 23.0 50.7
151B2061 24.0 52.9
151B2062 20.0 44.1
151B2063 20.5 45.2
151B2064 21.0 46.3
151B2065 22.0 48.5
151B2066 23.0 50.7
151B2067 24.0 52.9
151B2080 22.0 48.5
151B2081 22.5 49.6
151B2082 23.0 50.7
151B2083 24.0 52.9
151B2084 25.0 55.1
151B2085 26.0 57.3
151B2150 31.8 70.1
151B2151 32.6 71.9
151B2152 33.5 73.9
151B2153 34.9 76.9
151B2154 36.5 80.5
151B2155 31.8 70.1
151B2156 32.6 71.9
151B2157 33.5 73.9
151B2158 34.9 76.9
151B2159 36.5 80.5
151B2160 31.8 70.1
151B2161 32.6 71.9
151B2162 33.5 73.9
151B2163 34.9 76.9
Weight of motors
kg [lb]
151B2164 36.5 80.5
151B2170 32.4 71.4
151B2171 33.2 73.2
151B2172 34.1 75.2
151B2173 35.5 78.3
151B2174 37.1 81.8
151B2183 30.0 66.2
151B2184 30.8 67.9
151B2185 31.7 69.9
151B2186 33.1 73.0
151B2187 34.7 76.5
151B2188 30.0 66.2
151B2189 30.8 67.9
151B2190 31.7 69.9
151B2191 33.1 73.0
151B2192 34.7 76.5
151B3000 20.0 44.1
151B3001 20.5 45.2
151B3002 21.0 46.3
151B3003 22.0 48.5
151B3004 23.0 50.7
151B3005 24.0 52.9
151B3006 20.0 44.1
151B3007 20.5 45.2
151B3008 21.0 46.3
151B3009 22.0 48.5
151B3010 23.0 50.7
151B3011 24.0 52.9
151B3012 20.0 44.1
151B3013 20.5 45.2
151B3014 21.0 46.3
151B3015 22.0 48.5
151B3016 23.0 50.7
151B3017 24.0 52.9
151B3018 20.0 44.1
151B3019 20.5 45.2
151B3020 21.0 46.3
151B3021 22.0 48.5
151B3022 23.0 50.7
151B3023 24.0 52.9
Weight of motors
kg [lb]
151B3024 22.0 48.5
151B3025 22.5 49.6
151B3026 23.0 50.7
151B3027 24.0 52.9
151B3028 25.0 55.1
151B3029 26.0 57.3
151B3030 22.0 48.5
151B3031 22.5 49.6
151B3032 23.0 50.7
151B3033 24.0 52.9
151B3034 25.0 55.1
151B3035 26.0 57.3
151B3036 15.0 33.1
151B3037 15.5 34.2
151B3038 16.0 35.3
151B3039 17.0 37.5
151B3040 18.0 39.7
151B3041 19.0 41.9
151B3100 31.8 70.1
151B3101 32.6 71.9
151B3102 33.5 73.9
151B3103 34.9 76.9
151B3104 36.5 80.5
151B3105 31.8 70.1
151B3106 32.6 71.9
151B3107 33.5 73.9
151B3108 34.9 76.9
151B3109 36.5 80.5
151B3110 31.8 70.1
151B3111 32.6 71.9
151B3112 33.5 73.9
151B3113 34.9 76.9
151B3114 36.5 80.5
151B3115 32.4 71.4
151B3116 33.2 73.2
151B3117 34.1 75.2
151B3118 35.5 78.3
151B3119 37.1 81.8
151B3120 32.4 71.4
151B3121 33.2 73.2
Weight of motors
kg [lb]
151B3122 34.1 75.2
151B3123 35.5 78.3
151B3124 37.1 81.8
151B3125 22.7 50.1
151B3126 23.5 51.8
151B3127 24.4 53.8
151B3128 25.6 56.4
151B3129 27.7 61.1
151B3200 31.0 68.3
151B3201 31.5 69.4
151B3202 32.0 70.5
151B3203 33.0 72.8
151B3204 34.0 75.0
151B3205 35.0 77.2
151B3207 31.0 68.3
151B3208 31.5 69.4
151B3209 32.0 70.5
151B3210 33.0 72.8
151B3211 34.0 75.0
151B3212 35.0 77.2
151B4000 24.5 54.0
151B4001 25.0 55.1
151B4002 25.5 56.2
151B4003 26.5 58.4
151B4004 27.5 60.6
151B4005 28.5 62.8
151B4007 24.5 54.0
151B4008 25.0 55.1
151B4009 25.5 56.2
151B4010 26.5 58.4
151B4011 27.5 60.6
151B4012 28.5 62.8
151B4021 24.5 54.0
151B4022 25.0 55.1
151B4023 25.5 56.2
151B4024 26.5 58.4
151B4025 27.5 60.6
151B4026 28.5 62.8
151B4028 24.5 54.0
151B4029 25.0 55.1
Weight of motors
kg [lb]
151B4030 25.5 56.2
151B4031 26.5 58.4
151B4032 27.5 60.6
151B4033 28.5 62.8
151F0500 9.8 21.6
151F0501 10.0 22.1
151F0502 10.3 22.7
151F0503 10.7 23.6
151F0504 11.1 24.5
151F0505 11.6 25.6
151F0506 12.3 27.1
151F0507 9.8 21.6
151F0508 10.0 22.1
151F0509 10.3 22.7
151F0510 10.7 23.6
151F0511 11.1 24.5
151F0512 11.6 25.6
151F0513 12.3 27.1
151F0514 9.8 21.6
151F0515 10.0 22.1
151F0516 10.3 22.7
151F0517 10.7 23.6
151F0518 11.1 24.5
151F0519 11.6 25.6
151F0520 12.3 27.1
151F0521 10.3 22.7
151F0522 10.5 23.1
151F0523 10.8 23.8
151F0524 11.2 24.7
151F0525 11.6 25.6
151F0526 12.1 26.7
151F0527 12.8 28.2
151F0528 10.3 22.7
151F0529 10.5 23.1
151F0530 10.8 23.8
151F0531 11.2 24.7
151F0532 11.6 25.6
151F0533 12.1 26.7
151F0534 12.8 28.2
151F0535 7.8 17.2
Weight of motors
kg [lb]
151F0536 8.0 17.6
151F0537 8.3 18.3
151F0538 8.7 19.2
151F0539 9.1 20.1
151F0540 9.6 21.2
151F0541 10.3 22.7
151F0542 10.2 22.5
151F0543 10.4 22.9
151F0544 10.7 23.6
151F0545 11.1 24.5
151F0546 11.5 25.4
151F0547 12.0 26.5
151F0548 12.7 28.0
151F0560 9.8 21.6
151F0561 10.0 22.1
151F0562 10.3 22.7
151F0563 10.7 23.6
151F0564 11.1 24.5
151F0565 11.6 25.6
151F0566 12.3 27.1
151F0605 13.1 28.9
151F0608 11.1 24.5
151F0609 13.6 30.0
151F0610 13.6 30.0
151F2200 9.8 21.6
151F2201 10.0 22.1
151F2202 10.3 22.7
151F2203 10.7 23.6
151F2204 11.1 24.5
151F2205 11.6 25.6
151F2206 12.3 27.1
151F2207 9.8 21.6
151F2208 10.0 22.1
151F2209 10.3 22.7
151F2210 10.7 23.6
151F2211 11.1 24.5
151F2212 11.6 25.6
151F2213 12.3 27.1
151F2214 9.8 21.6
151F2215 10.0 22.1
Weight of motors
kg [lb]
151F2216 10.3 22.7
151F2217 10.7 23.6
151F2218 11.1 24.5
151F2219 11.6 25.6
151F2220 12.3 27.1
151F2235 10.3 22.7
151F2236 10.5 23.1
151F2237 10.8 23.8
151F2238 11.2 24.7
151F2239 11.6 25.6
151F2240 12.1 26.7
151F2241 12.8 28.2
151F2242 10.3 22.7
151F2243 10.5 23.1
151F2244 10.8 23.8
151F2245 11.2 24.7
151F2246 11.6 25.6
151F2247 12.1 26.7
151F2248 12.8 28.2
151F2261 13.1 28.9
151F2262 13.1 28.9
151F2263 13.6 30.0
151F2264 13.1 28.9
151F2265 13.6 30.0
151F2300 9.8 21.6
151F2301 10.0 22.1
151F2302 10.3 22.7
151F2303 10.7 23.6
151F2304 11.1 24.5
151F2305 11.6 25.6
151F2306 12.3 27.1
151F2307 13.1 28.9
151F2308 9.8 21.6
151F2309 10.0 22.1
151F2310 10.3 22.7
151F2311 10.7 23.6
151F2312 11.1 24.5
151F2313 11.6 25.6
151F2314 12.3 27.1
151F2315 13.1 28.9
Weight of motors
kg [lb]
151F2316 9.8 21.6
151F2317 10.0 22.1
151F2318 10.3 22.7
151F2319 10.7 23.6
151F2320 11.1 24.5
151F2321 11.6 25.6
151F2322 12.3 27.1
151F2323 13.1 28.9
151F2324 9.8 21.6
151F2325 10.0 22.1
151F2326 10.3 22.7
151F2327 10.7 23.6
151F2328 11.1 24.5
151F2329 11.6 25.6
151F2330 12.3 27.1
151F2331 13.1 28.9
151F2332 9.8 21.6
151F2333 10.0 22.1
151F2334 10.3 22.7
151F2335 10.7 23.6
151F2336 11.1 24.5
151F2337 11.6 25.6
151F2338 12.3 27.1
151F2339 13.1 28.9
151F2345 14.0 30.9
151F2346 14.0 30.9
151F2347 14.0 30.9
151F2348 14.0 30.9
151F2349 14.0 30.9
151F2350 9.8 21.6
151F2351 10.0 22.1
151F2352 10.3 22.7
151F2353 10.7 23.6
151F2354 11.1 24.5
151F2355 11.6 25.6
151F2356 12.3 27.1
151F2357 13.1 28.9
151F2358 14.0 30.9
151F2359 9.8 21.6
151F2360 10.0 22.1
Weight of motors
kg [lb]
151F2361 10.3 22.7
151F2362 10.7 23.6
151F2363 11.1 24.5
151F2364 11.6 25.6
151F2365 12.3 27.1
151F2366 13.1 28.9
151F2367 14.0 30.9
151F2368 9.8 21.6
151F2369 10.0 22.1
151F2370 10.3 22.7
151F2371 10.7 23.6
151F2372 11.1 24.5
151F2373 11.6 25.6
151F2374 12.3 27.1
151F2375 13.1 28.9
151F2376 14.0 30.9
151F2395 9.8 21.6
151F2396 10.0 22.1
151F2397 10.3 22.7
151F2398 10.7 23.6
151F2399 11.1 24.5
151F2400 11.6 25.6
151F2401 12.3 27.1
151F2402 13.1 28.9
151F2403 14.0 30.9
151F2413 9.8 21.6
151F2414 10.0 22.1
151F2415 10.3 22.7
151F2416 10.7 23.6
151F2417 11.1 24.5
Comatrol
www.comatrol.com
Schwarzmüller-Inverter
www.schwarzmueller- Local address:
inverter.com
Turolla
www.turollaocg.com
Hydro-Gear
www.hydro-gear.com
Daikin-Sauer-Danfoss
www.daikin-sauer-danfoss.com
Danfoss
Power Solutions Trading
Danfoss Danfoss Danfoss (Shanghai) Co., Ltd.
Power Solutions (US) Company Power Solutions GmbH & Co. OHG Power Solutions ApS Building #22, No. 1000 Jin Hai Rd
2800 East 13th Street Krokamp 35 Nordborgvej 81 Jin Qiao, Pudong New District
Ames, IA 50010, USA D-24539 Neumünster, Germany DK-6430 Nordborg, Denmark Shanghai, China 201206
Phone: +1 515 239 6000 Phone: +49 4321 871 0 Phone: +45 7488 2222 Phone: +86 21 3418 5200
Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to
products already on order provided that such alterations can be made without changes being necessary in specifications already agreed.
All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.