Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Steelwork Connections
Established 1934
Lindapter - Technical Innovation in Steelwork Connections
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Service and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Quality and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2 Cavity Fixings
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Type HB - Hollo-Bolt® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Type LB 2 - Lindibolt 2® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Typical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
1 Steelwork Fixings
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Girder Clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Bolt Length / Tail Length / Installation . . . . . . . . . . . . . . . . . . . . . . . .11
Type A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Type B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Accessories for Type A and B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Plate and Packing Details for Type A and B . . . . . . . . . . . . . . . . . . . .15
Type AF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Type CF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Accessories for Type AF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Plate and Packing Details for Type AF and CF . . . . . . . . . . . . . . . . . .19
Type LR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Type D2 and Type D3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Accessories for Type LR, D2 and D3 . . . . . . . . . . . . . . . . . . . . . . . . .22
Plate and Packing Details for Type LR, D2 and D3 . . . . . . . . . . . . . . .23
Type LS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Accessories / Plate and Packing Details for Type LS . . . . . . . . . . . . .25
Type BR and Type RC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Accessories / Plate and Packing Details for Type BR . . . . . . . . . . . . .27
Type Lindapter-HD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 3 Composite Decking Fixings
Type BSNT and Type BSLN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Type F9 and Type HW/HC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Type AW - Alphawedge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
Type SC and Type LP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 Type MW2 - Multiwedge 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Type FC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 Type TR60 and Type VN - V-Nut . . . . . . . . . . . . . . . . . . . . . . . . . . . .49
Loads and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Type SD2 - Slimdek 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50
Technical Enquiry Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 Type TC - Toggle Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
Typical Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Decking Fixings Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
Disclaimer
Lindapter International supplies components in good faith, on the
assumption that customers fully understand the loadings, safety factors
and physical parameters of the products involved. Customers or users
who are unaware or unsure of any details should refer to Lindapter
International before use. Responsibility for loss, damage, or other
consequences of mis-use cannot be accepted. Lindapter makes every
effort to ensure that technical specifications and other product
descriptions are correct. ‘Specification’ shall mean the specification
(relating to the use of the materials) set out in the quotation given by the
Seller to the Buyer. Responsibility for errors or omissions cannot be
accepted. All dimensions stated are subject to production tolerances -
if in doubt please check with Lindapter.
Applications
All the applications featured in the catalogue are based on real
projects. More information about these can be found on our website
www.lindapter.com.
© Lindapter 2009 © Lindapter International
© Lindapter is a registered trade mark
In the interests of improving the quality and performance of Lindapter
5 Floor Fixings products, we reserve the right to make specification changes without
prior notice.
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
Type FF - Floorfast® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65
Type GF - Grate-Fast® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66
Type GF3030 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
Engineered Solutions
Developing products that meet the needs of a particular project is
another Lindapter strength.
Sample Project
Bridge refurbishment:
Due to the age and condition of the structure the use of welded shear
studs was not possible. Instead modified Hollo-Bolts® were used which
enabled the bridge deck refurbishment to be completed on time and to
specification. Special Hollo-Bolt®
For further information regarding this project see website Standard Hollo-Bolt®
www.lindapter.com.
Product quality is one of the main life lines The American Insurance Association, Factory Mutual,
of the Lindapter philosophy, the entire offers an approval which is recognised by the fire
company is particularly dedicated to this protection industry world-wide.
aspect. Lindapter has been accredited to
BS EN ISO 9001 since 1986.
Verband der Schadenversicherer e.V. is a German
Q 05143
insurance association who also offers a rigorous
approval for products used in the fire protection
industry.
Approvals
Lindapter has been trading internationally for many years respecting
These approvals serve to reinforce Lindapter’s extensive in-house
the market differences around the world. The relevant international
testing procedures. Lindapter products are tested so that the user can
authorities have granted many product approvals over time.
be confident whether specifying or using that Lindapter products will
The catalogue refers to them product by product.
perform as per the information detailed in this catalogue. Loads
Approvals for construction published are the product safe working loads, taking into account a
factor of safety.
The Deutsches Institut für Bautechnik, Berlin is a body
which approves products and materials for use in
structural engineering applications in the construction Corrosion Protection
and civil engineering industries in Germany. Lindapter products are delivered as standard either bright zinc plated
or hot dip galvanised. Various other coatings and alternative materials
Lloyds Register Type Approved products have been are available upon request for most products including:
subjected to tensile, frictional, shear, vibration and • Sheradising • Delta seal
shock tests, witnessed and verified by Lloyds
• Mechanical galvanising • Delta tone
Register.
• Plastic coating • Sheraplex
The TÜV is the certifying authority for safety, • Special paint coating • Stainless steel
quality and environmental protection in Germany.
Lindapter is a member of the following organisations:
Det Norske Veritas has approved the use of Lindapter
products in lifting applications. This includes their use
on both mobile and fixed offshore installations.
Steelwork Fixings
Lindapter Steelwork Fixings can be used in a wide
variety of applications for connecting together steel
sections of whatever shape and size; uppermost in
this section is the Girder Clamp which, as with
most Lindapter products, needs no on site drilling
or welding saving both time and money by reducing
installed costs. Numerous world wide project
successes have demonstrated that this is ideally
suited for both new construction and refurbishment
of existing structures.
Advantages
• Reduces design time
• Guaranteed loads and approvals
• No on-site drilling or welding
• ‘Hot Working’ not required
• Less work at height
• Only hand tools required to install
• Site adjustable
• Power not required
• Ability to deconstruct and multi-cycle
rather than demolish
Markets include:
• Plant Engineering
• Chemical and Petro-chemical Industry
• Materials Handling
• Structural Engineering
• Civil Engineering
• Facades
• Theatre Equipment
• Transportation
• Offshore
Applications include:
• Steel Constructions
• Cranes
• Lifting Beams
• Pipe Supports
• Towers and Masts
9
Girder Clamps Steelwork Fixings 1
Loads 7
The table beneath shows tensile and frictional load capabilities for a
standard four bolt Girder Clamp using 4 bolts and 8 clamps at a 90°
crossover angle. Lindapter is only too pleased to carry out all design work
for individual connections free of charge based on the following details:
• Load per connection
• Size and type of both beams
• Angle of crossover
• Distance between beams
• Inclination of beams
All loads are based on actual test data having a factor of safety for friction against slip and for tensile against ultimate failure
(typically 5:1). Use of lower safety factor is not recommended.
Approvals
All approvals apply to Girder Clamps using types A and B only, in sizes from M12 to M24 Further information is available upon request.
One dimple:
tail length short (s)
0.5 · bolt Ø
as bolt protrusion 10
Height of nut 16
+ Washer 3
+ T of top clamp 20
Two dimples:
tail length medium (m)
+ Top section 12.5
+ Plate thickness 12
+ Lower section 10
+ T of lower clamp 10
Three dimples:
tail length long (l )
= 93.5
Next standard
bolt length = 100.0
Parallel flanges
Maximum tail length tolerance of -1mm (up to M16) and -1.5mm (M20, M24) before applying the torque is acceptable.
Tapered flanges
<90º
<_5º 90º 5-8º
On 6º and 8º slopes types A and B require a special tail length/packing combination which will allow the clamp to tilt back slightly (incorporated into the
combination table on page 15).
For applications above 8° please see types AF, LR and LS.
Type A
Malleable iron, bright zinc plated / hot dip galvanised
Nose Recess
Clamping Area K
Skirt Tail
T
V
Y X
Typical Applications Steelwork clamp with recessed top to hold the bolt head captive whilst
(see also page 36-39) the nut is tightened. The skirt prevents the clamp rotating during
installation. Suitable for flanges up to 8°.
The clamp is installed correctly when the area ‘K’ grips the flange.
The tail must be chosen to suit the thickness of the flange being
gripped. For correct tail length/packing combinations please see
page 15.
For higher loads the type AF should be used (see page 16).
Type B
Malleable iron, bright zinc plated / hot dip galvanised
Clamping
Area K Skirt
Tail
T
V
Y X
Steelwork clamp with flat top which allows the bolt head or Typical Applications
nut to be rotated. Suitable for use with all bolts, studs, tie (see also page 36-39)
rods and J-bolts, and flanges up to 8°.
The clamp is installed correctly when the area ‘K’ grips the
flange. The tail must be chosen to suit the thickness of the
flange being gripped. For correct tail length/packing
combinations please see page 15.
For higher loads the type AF should be used (see page 16).
Type T
Malleable iron, bright zinc plated /
hot dip galvanised T
Product Bolt Dimensions
Code Z T
mm
T12 M12 3
Z T16 M16 4
T20 M20 5
To fill the nose of type A and B making it horizontal. For parallel flanges
only. The thickness ‘T’ should be added for tail length and bolt length T24 M24 6.5
calculations. The product is for aesthetic purposes only and technically Order example: T12 BZP
not necessary.
Type W
Mild Steel, malleable iron, bright zinc plated / Product Bolt Dimensions
hot dip galvanised T Code Z T
mm
W08 M8 4
W10 M10 5.5
W12 M12 6.5
Z W16 M16 8
W20 M20 9.5
Washer to fill the recess of type A to enable the nut to be tightened. Order example: W08 BZP
When calculating the bolt length please add ‘T’.
L1 = Plate length
L2 = Plate width b2 l2M L2
l2M L2
l1M, l2M = Hole centres
b1, b2 = Flange width
d= Hole Ø d
s= Plate thickness d
Type AF
SG iron, hot dip galvanised
Recess
Nose
Skirt
Tail
Y X
With washer inverted Type AFW
for bolt grade 10.9 with larger hexagons
(M12 - M20)
Typical Applications
(see also page 36-39)
High friction clamp with recessed top to hold bolt head captive whilst
the nut is tightened. Can be combined with type CF. The skirt prevents
the clamp rotating during installation. The tail of the AF spans across
slotted holes. For flanges up to 10°. Washer type AFW available
(see illustration).
For correct tail length/packing combinations please see page 18.
Type CF
SG iron, hot dip galvanised
Anti-rotation markings
Nose
Legs
Y X Y X
min T
max T
Z Z
min t max t
Typical Applications
(see also page 36-39)
High friction clamp which hooks over flanges of I-beams, angles and
channels. Lindapter markings act as a unique anti-rotation device.
Can be combined with all Lindapter Girder Clamp products including
type AF.
Type AFCW
Mild Steel, hot dip galvanised
Type AFW
SG iron, malleable iron, hot dip galvanised
T
Product Bolt Dimensions
Code Z T
mm
AFW12 M12 5
AFW16 M16 5
AFW20 M20 6
Z AFW24 M24 10
Washer filling the recess of the type AF. Order example: AFW12
Additionally it features two projections T
which, when the AFW is inverted, will
captivate the larger hexagons of 10.9
bolts. (M12 – M20 only). M24 version has no projections.
L1 = Plate length
b2 l2M L2
L2 = Plate width l2M L2
l1M, l2M = Hole centres
b1, b2 = Flange width
d= Hole Ø d
s= Plate thickness d
Plate Dimensions
Material: Mild Steel Grade S355 JR (for other grades please contact Lindapter)
Location Plate End Plate1)
Plate Plate
Bolt Hole Ø Thickness Hole Centres Length/Width Thickness Hole Centre Length Hole Centre Width
Z d s l1M, l2M min L1, min L2 s l1M min L1 min l2M min L2
mm mm mm mm mm mm mm mm mm
M12 13 10 b + 13 b + 90 15 b1 + 13 b1 + 90 80 l2M + 80
M16 18 15 b + 18 b + 110 25 b1 + 18 b1 + 110 100 l2M + 100
M20 22 20 b + 22 b + 130 30 b1 + 22 b1 + 130 180 l2M + 180
M24 26 25 b + 26 b + 180 40 b1 + 26 b1 + 180 200 l2M + 200
1) Dependant on the use of the end plate the thickness might need to be increased.
2) For combinations of Type CF with A, B and BR see page 15 and for types D2, D3 and LR see page 23.
Type LR
Malleable iron, bright zinc plated / hot dip galvanised
Saddle
Slot
Nose
Leg
Clip Tail
max Y min X
max T
min V
min Y max X
min T
max V
Typical Applications
(see also page 36-39)
Type D2
Malleable iron, bright zinc plated,
hot dip galvanised
S
Recess
T
Nose
V
Setscrew
Tail
Clamping Y X
Area K
Skirt
Z
Type D3
Malleable iron, bright zinc plated, Z
hot dip galvanised
S
Flat Top
T
Y X
Type T
Malleable iron, bright zinc plated /
T
hot dip galvanised
Product Bolt Dimensions
Code Z T
mm
T12 M12 3
T16 M16 4
Z T20 M20 5
To fill the nose of type D2 and D3 making it T24 M24 6.5
horizontal. For parallel flanges only. Order example: T12 BZP
The thickness ‘T’ should be added for tail
length and bolt length calculations. The product
is for aesthetic purposes only and technically
not necessary.
Type W
Mild Steel, bright zinc plated /
hot dip galvanised
L1 = Plate length
L2 = Plate width b2 l2M L2
l2M L2
l1M, l2M = Hole centres
b1, b2 = Flange width
d= Hole Ø d
s= Plate thickness d
Type LS
Cast Stainless Steel equivalent to Grade 316
Nose
Tail
min Y max X
max T
min V
max Y min X
min T
max V
Typical Applications
(see also page 36-39)
Z
Self adjusting clamp for various flange thicknesses and slopes up to 10°.
The special serrations on the tail prevent the clamp rotating during
installation. The LS tail spans over slotted holes.
Accessories
Packings are available upon request.
L1
L1
l1M
Location and End Plates l1M
b1 b1
L1 = Plate length
L2 = Plate width b2 l2M L2
l2M L2
l1M, l2M = Hole centres
b1, b2 = Flange width
d= Hole Ø d
s= Plate thickness d
Plate Dimensions
Material: Mild Steel Grade S275 JR or S355 JR
Flat Top
Type BR Nose
Malleable iron, bright zinc plated / hot dip galvanised
Clamping
Area K
Skirt Tail
Z
T
V
Y X
Versatile clamp for steel beams or rails. The skirt prevents the clamp
rotating during installation. The BR tail spans slotted holes.
Suitable for flanges up to 8°.
Skirt
Tail
t1
Type Lindapter-HD
Malleable iron, SG iron, corrosion protection as requested Lindapter-HD Plug
Nose
Leg
Skirt
Elastomer Spring
Dimensions
Product Clip Bolt 8.8 Lateral Safe Working Load Leg Stud Lateral Adjustm. Plate Width Distances Width
Code Type Z (4:1 Factor of Safety) Torque V Length H max L min A X2) Y2) W
kN Nm mm mm mm mm mm mm mm
HD20 H Hard M20 46 450 F-8 F + 38 ± 11.5 B + 137 30 27 74
HD20 S Soft M20 46 450 F-5 F + 40 ± 11.5 B + 137 30 27 74
HD20 SP Spring M20 46 450 F-7 F + 40 ± 11.5 B + 137 30 27 74
HD20 S-P Soft & Pad M20 46 450 F1) F + 45 ± 11.5 B + 137 30 27 74
HD20 SP-P Spring & Pad M20 46 450 F - 21) F + 45 ± 11.5 B + 137 30 27 74
NB: Leg length V for use with rail sections only with tapered base. For parallel sections please refer to Lindapter.
Lindapter-HD
The spring clip version incorporates an elastomer spring into the nose
of the product, designed to provide some vertical restraint to the rail
whilst still allowing the rail to lift with rail wave.
The elastomer spring is manufactured from high density synthetic H
polymer which has a Shore A hardness of 94.97. The spring is F V
unaffected by salt water and most chemicals and has a high resistance
to abrasion. Y X B
A
Resilient Pad
Both the spring and soft clips can be used with a resilient pad to
decrease track running noise /structural vibration, level out irregular
contact between surface and rail and to spread wheel load evenly over V
a wider area.
Resilient Pad
Y X
Skirt Tail
Z
T
V
K
Y X
Special clamp designed with longer nose to extend the contact area
with the steel section. For parallel flanges only. Can be used with types
CW, P1 short, P2 short.
Type F9
Malleable iron, bright zinc plated / hot dip galvanised
Nut Bolt Z
Single Leg V
Jaws T
W X
Double Leg
Flange Clamp for connecting all types of parallel running steelwork with
flanges of the same width. Can be used with bolts or alternatively with
threaded rod.
Not suitable for tapered flanges.
Type HW/HC
Malleable iron, bright zinc plated / X
hot dip galvanised Z
Hemispherical Washer
R
W1 L
W2
10°
Hemispherical Cup
For vertical suspension on angled surface of up to 10° swing either side of
the vertical. The hemispherical washer (HW) can be used without the cup.
Loads are subject to applications, please contact Lindapter.
Dimensions
Product Code Hemispherical Washer Hemispherical Cup Hemispherical Washer & Cup
Hemispherical Washer Hemispherical Cup X W1 Y W2 R L
mm mm mm mm mm mm
HW06 - 19 9 - - - -
HW08 - 22 10 - - - -
HW10 HC10 25 12 32 12 13 14
HW12 HC12 29 12 35 12 14 16
HW16 HC16 34 16 41 16 17 19
HW20 HC20 44 19 54 19 22 24
HW24 HC24 57 25 67 25 29 32
Type SC / Type LP
Corrosion Protection as required
Bespoke units for multiple applications with vertical load, loads at an angle and rotation of up to 360°. Shown are typical applications, other loads and
designs available. All loads subject to suitability of supporting section.
Type SC
Type SC
Shackle Clamp with 4 Bolts
Loading: up to 60.0kN
Directions: vertical lift
Angle: ± 10º
Type LP4
Type LP4
Lifting Point with 4 Bolts
Loading: up to 7t (68kN)
Directions: 360º rotation
Angle: 0 - 90º
Type LP6
Type LP6
Lifting Point with 6 Bolts
Loading: up to 10t (98kN)
Directions: 360º rotation
Angle: 0 - 90º
Type FC
Forged steel, bright zinc plated plus JS500
min V max V
max T
min T
Special Bolt B
Top Beam
Flange 76.2 101.6 127.0 152.4 177.8 Angle
Width mm mm mm mm mm
76.2 mm 45° 50° 55° 65° 75°
Bottom Beam
Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Full Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Department . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
...............................................................................................................
1. Is your case comparable with an application in this catalogue? If yes, please state page and number . . . . . . . . . . . . . . . . . . . . . . .
Tensile . . . . . . . . . . . . . . . kN
Frictional . . . . . . . . . . . . . kN
Static Load ❍
Dynamic Load ❍ Load Cycles . . . . . . . . . . . . . . .
Top Beam
Bottom Beam
1 2 3
4 5 6
7 8 9
10 11 12
13 14 15
5
16 17 18
19 20 21
22 23 24
25 26 27
28 29 30
31 32 33
34 35 36
Cavity Fixings
In the late 1940’s Lindapter revolutionised the
concept of ‘blind’ fixing, or where limited access is
available, with the development of the Lindibolt.
Some time later, following the introduction and
wide acceptance of hollow section steelwork, the
range was expanded to include the Hollo-Bolt®.
40
Type HB - Hollo-Bolt® Cavity Fixings 2
Type HB - Hollo-Bolt®
Steel, bright zinc plated plus JS 500
Steel, hot dip galvanised
Stainless Steel Grade 316
Collar
Rubber Washer
Sleeve
Cone
Suitable for hollow sections, tubes and where access is available from
one side only. For high corrosion protection the Hollo-Bolt® comes with
additional JS500 protection as standard or hot dip galvanised.
Sizes M16 and M20 have a patented collapse mechanism for
optimised clamping force. Speedy installation with standard tools and
for the Type Hollo-Bolt® Flush Fit with installation nut. (One free per box)
Awarded the Design Council’s Millennium Product status for
innovation in the year 2000.
D D d
d
Rubber Washer
W
W
Rubber Washer compressed /
increased clamping force
*8
Head Variations
Flush Fit Countersunk Hexagonal Head Socket Head Button Head Security
(Head) Cap Screw
M8-M12 M8-M16 M8-M20 Supplied to order Supplied to order
1) The thickness of the outer ply needs to be at least 8mm. If necessary spacer washers should be used beneath the collar to
increase the thickness to 8mm.
2) The Hollo-Bolt® can be used on a wide variety of SHS sections; those shown above are only representative to give an
indication of variations in Hollo-Bolt® capacity.
The safe working loads, in both tension and shear, are applicable to the Hollo-Bolt® only, failure of the section, particularly
on those with thin walls and a wide chord face, could occur at a lower figure and its strength should be checked using the
‘Green Book’ design guide.
Setscrew
Cone
Locknut
Nut
D C W
F B A
d Z
P
Y
W
Self heading bolt suitable for fixing to hollow-sections, tubes and where
access is available from one side only. The Lindibolt® uses a standard
clearance hole.
1 2
3 4
5 6
Advantages include:
• Speed of installation
• No special tools required
• No weakening of the decking profiles
• No damage of the surfaces of the decking
• No possibility of delamination
• Adjustable and easily removable
Type AW - Alphawedge
Locking Plate: Pre-galvanised strip
Wedge: Malleable iron, bright zinc plated
Wedge
Locking Plate
Installation
1. 2. 3. 4.
1. Pre-assemble the Alphawedge and Locking Plate onto the threaded rod (flat surface uppermost).
2. Insert wedge into the re-entrant channel of the decking, rotate 90°.
3. Slide plate up the threaded rod, over the wedge, to lock it in position into the channel.
4. Tighten the locknut beneath the plate to hold the assembly in position.
Bracket
The Multiwedge 2 is designed for MD60 and MD80 profiles Safe Working Load
manufactured by Kingspan Structural Products (see page 52). Product Rod (3:1 Factor of Safety)
Code 4.6 Tensile / 1 Rod Torque
kN Nm
MW06 M6 1.47 10
MW08 M8 1.47 10
MW10 M10 1.47 10
Installation
1. 2. 3. 4.
1. Position Multi-nut and bracket on threaded rod (flat surface uppermost) and insert one leg of bracket into re-entrant channel of decking.
Snap other leg of bracket into channel.
2. Slide assembly to desired position along length of re-entrant channel.
3. Push and turn the multi-nut clockwise until it locks into the channel walls.
4. Tighten the hexagon nut beneath the assembly.
Type TR60
Locking Plate: Pre-galvanised strip
Wedge: Malleable iron, bright zinc plated
Wedge
Locking Plate
Type VN - V-Nut
Malleable iron, mild steel, bright zinc plated Installation
12.5mm
1. 2. 3.
25mm
13mm
Cam
The Slimdek 2 is designed for the CF225 profile manufactured by Safe Working Load
Corus Panels and Profiles. It gives a fully flexible suspension position Product Rod (3:1 Factor of Safety)
(see page 52).
Code 4.6 Tensile / 1 Rod Torque
kN Nm
SD206 M6 1.0 12
SD208 M8 1.0 12
SD210 M10 1.0 12
Installation
1. 2. 3.
4. 5. 6.
1. With Slimdek 2 in it’s retracted position (as supplied) locate the fixing in the re-entrant channel.
2. Hold Slimdek 2 in position with one hand, then rotate cam into the direction shown above with a spanner.
3. Rotate the nut until the inner body of the fixing locates against the re-entrant channel, and the nut feels tight.
4. Offer the V-Nut on a threaded rod up to the main body.
5. Rotate V-Nut through 90° to allow it to sit at the bottom of the Slimdek 2 body.
6. Secure the assembly with a nut.
Nut
Toggle
Installation
LIN
DA
PT
ER
LINDAPTER
LINDAPT
ER LINDAPTER
LINDAPTER
1. 2. 3. 4. 5. 6.
1. Drill hole. If toggle is to be used to support from pre-cast hollow core slab, ensure hole is central to hollow core.
2. Insert threaded rod through toggle, ensuring nut is flush with end of rod.
3. Align toggle parallel with rod, so that nut engages into the retaining cavity.
4. Offer up the assembly, inserting the toggle body completely through the hole.
5. Shake rod so that toggle body locates horizontally across hole.
Allow rod to drop down so that the nut locates in the seat in the toggle body.
6. Wind up rod to top of section as shown as high as possible. Secure the assembly with a nut and washer.
• Ribdeck AL
• Ribdeck E60
• Ribdeck 80
• MD60
• MD80
• TR60
• TR80
• CF225
Installation
Type AW - Alphawedge
1. Pre-assemble the Alphawedge and locking plate onto the threaded
rod (flat surface uppermost).
2. Insert wedge into the re-entrant channel of the decking, rotate 90°.
3. Slide plate up the threaded rod, over the wedge, to lock it in position
into the channel.
4. Tighten the locknut beneath the plate to hold the assembly
in position.
1. 2. 3. 4.
Type TR60
1. Pre-assemble the wedge and locking plate onto the threaded rod
(flat surface uppermost).
2. Insert wedge into the re-entrant channel of the decking and rotate
until the chamfered cams engage on the sides of the channel.
3. Slide the plate up the threaded rod and over the wedge to lock it
into position in the channel.
4. Tighten the locknut beneath the plate to hold the assembly in
1. 2. 3. 4.
position.
Type VN - V-Nut
1. 2. 3. 1. Screw VN onto threaded rod.
2. Insert VN and rod into re-entrant channel of decking.
3. Rotate both rod and VN through 90° so that tapered sides
engage the sides of the channel.
Support Fixings
Lindapter’s support fixing range offers a series of ideal solutions for all
building services. This includes the suspension of HVAC equipment,
pipe work, fire protection/sprinkler systems, suspended ceilings and all
manner of electrical equipment such as cable tray and ladder. These
products have all been designed to give speed and ease of installation
to reduce time and keep costs under control.
Type FLS
High Grade Alloy Steel, bright zinc plated
Setscrew Z
Locknut
Swivel Unit
Nut Basket
T
U
W X
R
360º
Beam flange clamp with swivel unit. For parallel and sloping flanges.
Supplied with grade 8.8 setscrew for secure grip.
Z
N
M
S
1. 2. 3. 4.
) 25° ) 25° ) 25°
General Applications
1. Locate FLS onto flange. Parallel Flanges only
2. Ensuring lug on locknut locates into main body, tighten down
setscrew (Z), and then tighten upper locknut (N).
3. Install threaded rod by screwing into nut located in nut basket (S).
90°
Ensure full thread capture.
4. Secure assembly in nut basket (S) from beneath using a locknut
(not supplied).
Ensure that the cup point setscrew always grips on the ) 45° ) 45°
tapered side of the flange.
Type FL
Malleable iron,
bright zinc plated
Hexagon Setscrew
Square Head Setscrew
Locknut
Rear Hole
(Tapped / Clear)
Main Body
Z
N
T
V W U
X Y
Beam Clamp suitable for use with parallel or tapered flange beams, supplied
with the back hole drilled or tapped. The type FL uses a grade 8.8 cup point
setscrew for secure grip. Supplied with square or alternatively hexagon head
setscrews.
Can be used with type SW – Swivel Unit (see page 57) when connecting to
inclined sections.
Installation
1. Slide FL onto beam flange and tighten setscrew to
recommended torque. Guideline: tighten the setscrew finger
tight and then apply a further quarter turn (90°) with spanner.
2. Tighten the locknut (N) to the recommended torque.
On tapered flanges the cup point setscrew has to grip on the
inside of the flange.
Type LC
Malleable iron, bright zinc plated
Setscrew
Locknut
Main Body
N
T
V
W X U
Beam clamp with tapped holes in position X and Y to accept threaded rod or cable clips.
For parallel or tapered flanges. Supplied with grade 8.8 cup point setscrew.
Y
Installation see page 56 – type FL
Type Z10
R
V
Swivel unit for applications on inclined beams. Can be used with type FL or type Z10.
Supplied complete with grade 8.8 M10 x 90 setscrew and nut.
Single Leg
Double Leg
Z
T
V
R S W X
V
A two part flange clamp with large clamping range.The bolt can be
substituted with either drop rod or J bolts.
For parallel flanges only.
Type F3-BICC
Malleable iron, hot dip galvanised
Z
T
V1
Y
W X
S
V2
Y
A two part flange clamp which fixes claw type cable cleats directly
beneath the flange.
Supplied with grade 4.6 bolt.
Type SH
Pre-galvanised strip
Hanger Nut
Y
With special nut
A
C
B
Type HW/HC
Malleable iron, bright zinc plated / X
hot dip galvanised Z
Hemispherical Washer
R
W1 L
W2
10°
Hemispherical Cup
For vertical suspension on angled surface of up to 10° swing either side of
the vertical. The hemispherical washer (HW) can be used without the cup.
Loads are subject to applications, please contact Lindapter.
Dimensions
Product Code Hemispherical Washer Hemispherical Cup Hemispherical Washer & Cup
Hemispherical Washer Hemispherical Cup X W1 Y W2 R L
mm mm mm mm mm mm
HW06 - 19 9 - - - -
HW08 - 22 10 - - - -
HW10 HC10 25 12 32 12 13 14
HW12 HC12 29 12 35 12 14 16
HW16 HC16 34 16 41 16 17 19
HW20 HC20 44 19 54 19 22 24
HW24 HC24 57 25 67 25 29 32
Type Z10
Mild steel - bright zinc plated
A purlin clip to suit a large range of purlin sections. Can be used with
type SW – Swivel Unit (see page 57) for use on inclined purlins.
Type HCW30
Pre-galvanised strip
The purlin clip HCW30 is suitable for horizontal purlins. Can be used
with type SW-Swivel Unit (see page 57) for use on inclined purlins.
Installation
Type HCW31
Pre-galvanised strip
Type WF
Mild Steel, bright zinc plated
The Webfix – WF for a quick installation directly from the web of Zed purlins.
Installation
Squeeze legs of WF
together and push
through hole until it Assemble with nut and ensure
snaps into place. full thread capture.
1. 2.
Type HCW34
Pre-galvanised strip
Purlin
Kingspan Multibeam 3 Safe Working Load (3:1 Factor of Safety)
Product Code Purlin Height Total Height H Rod Tensile
mm mm kN
HCW34/145 145 210 M10 0.75
HCW34/175 175 240 M10 0.75
HCW34/205 205 270 M10 0.75
HCW34/235 235 300 M10 0.75
HCW34/265 265 330 M10 0.75
Purlin Profiles
1 2 3
Type HCW31
Type HCW30
Type Z10
Type SH
Type SH
Floor Fixings
When designing the floor fixing range of products for chequer plate
and both square and rectangular open bar grating Lindapter combined
speed with ease of installation. None of the products require any site
drilling and/or welding to be done and can easily be installed from
above the flooring; this means no requirement for scaffold towers,
access platforms or MEWP hire giving easier compliance with the
onerous work at height regulations.
Both the Floorfast® & Grate-Fast® are covered by Lloyds Register Type
Approval in respect of their clamping force and resistance to loosening
in areas subject to shock and vibration. Without a need for the issuing
of hot work permits, they are particularly suited to applications where
safety is of paramount importance such as in offshore and onshore
petrochemical and processing industries although they are equally
ideal for applications in all other industrial environments.
Type FF - Floorfast®
Malleable iron, Stainless Steel Grade 316,
bright zinc plated / hot dip galvanised
Unique stepped
clamping face
Socket
setscrew
90º
20 D
2 t1
t
d
Z
60 A - Nominal Clearance
Countersunk
Product Floorplate Flange Countersunk Ø for Bolt Countersunk Depth for Bolt Hexagon
Code Bolt1) Thickness Thickness Hole Ø BZP HDG BZP HDG Torque Key
Z t d D t1
mm mm mm mm mm Nm mm
FF08 M8 4.5 - 12 3 - 15 9 17 - 4 - 11 5
FF10 M10 5 - 12 3 - 15 11 21 19 5 4 22 6
FF12 M12 6 - 12 3 - 15 13.5 25 23 5.8 4.8 22 8
1) In hot dip galvanised (M10 and M12) a slotted countersunk screw is supplied.
Installation
1.
2.
3.
1. Pre-assemble Floorfast® on underside of floorplate 4.
with stepped surface facing inwards. 5.
2. Align castings with straight edge parallel
to the edge of the plate and hand tighten.
3. Lay floorplate into position
4. Using a hexagon key release the countersunk screw
one full turn.
5. Tighten down the countersunk socket screw.
Removal
Using a hexagon key, give the Type FF one full anticlockwise turn to release connection from the flange.
Type GF - Grate-Fast®
Body: Malleable iron, mechanical galvanised
Top Hat: Mild Steel, mechanical galvanised
Socket Head
Cap Screw
Cast Body
min X X
max X
Installation
1. Position pre-assembled Grate-Fast® with body
between grating bars and nose pointing towards the
steelwork. The arrows on the top hat bracket should
also be pointing towards supporting steelwork and
bracket itself resting on the bearing bars.
Type GF3030
Spring Steel, Sheraplex
Installation
1. 2. 3.
1. Position the fixing with the grating bar located between the two tabs on the upper profile, facing towards the supporting steelwork.
2. Apply a downward force to the fixing, so that the lower leg passes through the grating.
3. Apply a downward force to the top of the fixing. The fixing then snaps in to place. If the lower profile contacts the steelwork web,
the GF3030 will automatically relocate itself.
Removal
Using a screwdriver or lever, raise the back of the GF3030 into position shown in diagram 2.
Place the lever between the steelwork and lower leg of the fixing and prise GF3030 away from steelwork.
Advance® UKB
Dimensions: BS4-1:2005
Advance® UKPFC
Dimensions: BS4-1:2005
Designation Mass D B T
Serial Size kg/m mm mm mm B
430 x 100 x 64 64.4 430.0 100.0 19.0
380 x 100 x 54 54.0 380.0 100.0 17.5
300 x 100 x 46 45.5 300.0 100.0 16.5
300 x 90 x 41 41.4 300.0 90.0 15.5
260 x 90 x 35 34.8 260.0 90.0 14.0
D
260 x 75 x 28 27.6 260.0 75.0 12.0
230 x 90 x 32 32.2 230.0 90.0 14.0
230 x 75 x 26 25.7 230.0 75.0 12.5
200 x 90 x 30 29.7 200.0 90.0 14.0
200 x 75 x 23 23.4 200.0 75.0 12.5 T
180 x 90 x 26 26.1 180.0 90.0 12.5
180 x 75 x 20 20.3 180.0 75.0 10.5
150 x 90 x 24 23.9 150.0 90.0 12.0
150 x 75 x 18 17.9 150.0 75.0 10.0
125 x 65 x 15 14.8 125.0 65.0 9.5
100 x 50 x 10 10.2 100.0 50.0 8.5
Advance® UKC
Dimensions: BS4-1:2005
Designation Mass D B T
Serial Size kg/m mm mm mm B
356 x 406 x 634 633.9 474.6 424.0 77.0
551 551.0 455.6 418.5 67.5
467 467.0 436.6 412.2 58.0
393 393.0 419.0 407.0 49.2
340 339.9 406.4 403.0 42.9
D
287 287.1 393.6 399.0 36.5
235 235.1 381.0 394.8 30.2
356 x 368 x 202 201.9 374.6 374.7 27.0
177 177.0 368.2 372.6 23.8
153 152.9 362.0 370.5 20.7 T
129 129.0 355.6 368.6 17.5
305 x 305 x 283 282.9 365.3 322.2 44.1
240 240.0 352.5 318.4 37.7
198 198.1 339.9 314.5 31.4
158 158.1 327.1 311.2 25.0
137 136.9 320.5 309.2 21.7
118 117.9 314.5 307.4 18.7
97 96.9 307.9 305.3 15.4
254 x 254 x 167 167.1 289.1 265.2 31.7
132 132.0 276.3 261.3 25.3
107 107.1 266.7 258.8 20.5
89 88.9 260.3 256.3 17.3
73 73.1 254.1 254.6 14.2
203 x 203 x 127 127.5 241.4 213.9 30.1
113 133.5 235.0 212.1 26.9
100 99.6 228.6 210.3 23.7
86 86.1 222.2 209.1 20.5
71 71.0 215.8 206.4 17.3
60 60.0 209.6 205.8 14.2
52 52.0 206.2 204.3 12.5
46 46.1 203.2 203.6 11.0
Use of the Advance® name and range of sections
152x 152 x 51 51.2 170.2 157.4 15.7 by kind permission of Corus.
44 44.0 166.0 155.9 13.6
37 37.0 161.8 154.4 11.5
30 30.0 157.6 152.9 9.4
23 23.0 152.4 152.2 6.8
General Enquiries
Date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Company . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Full Name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Department . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Town . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Postcode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
...............................................................................................................
...............................................................................................................
...............................................................................................................
Lindapter would like to keep you informed about the latest developments which could be valuable for you.
...............................................................................................................
...............................................................................................................
...............................................................................................................
...............................................................................................................
...............................................................................................................
www.lindapter.com