Documentos de Académico
Documentos de Profesional
Documentos de Cultura
SERVICEMANUAL US Model
Chassis No. SCC-E54H-A
Canadian Model
Chassis No. SCC-E65E-A
SPECIFICATIONS
TRINlTRONdOLOR TV
Impedance: 5 kilohms
SONX
996479501
SECTION 3
SET-UP ADJUSTMENTS
l The following adjustments should be made when a Perform the adjustments in order as follows :
complete realignment is required or a new picture 1. Beam Landing
tube is installed. 2. Convergence
l These adjustments should be performed with rated 3. Focus
power supply voltage unless otherwise noted. 4. White Balance
Note : Test Equipment Required.
Controls and switch should be set as follows unless 1. Color-bar/Pattern Generator
otherwise noted : 2. Degausser
PICTURE control . . . . . . . . . . . . RESET 3. Oscilloscope
BRIGHTNESS control . . . . . . . . . . center
. . . ... . . . . . . . . . .... . . . . .
Preparations :
0 In order to reduce the influence of geomagnetism
on the set’s picture tube face it east or west.
* Switch on the set’s power and degauss with the
degausser. Purity control
-24-
1 3-2. CONVERGENCE 1 0 Tilt the V.STAT magnet and adjust the static
Preparation : convergence by opening or closing the V.STAT
l Before starting this adjustment, adjust the focus, magnet.
horizontal size, and vertical size.
l Minimize the brightness setting.
l Provide dot pattern.
V. STAT Magnet
14 A
H. STAT
I
R G B
RV 701 H. STAT
RV 708 (G 2) SCREEN
-25-
KV-27TS35
RM-YlO2 I
@ Operation of BMC (Hexapole) Magnet 0 The respective dot positions resulting from
moving each magnet interact, so be sure to
RG 8 RG8 R GB
-e-o- perform adjustment while tracking.
Use the HSTAT VR to adjust the red, green, and
blue dots so they coincide at the center of screen
(by moving the dots in the horizontal direction).
Purity
Purity
II V.STAT m a g n e t
BMC I Hexa~ole~ mannet 1 I
-
R GB B G R
-26-
KV-27TS35
RM-Y102
-27-
-D Board - - D Board -
0 0 0 IC D115
D116
A.2
B-2
IClOl B-3 D117 A-8
IC102 c-3 D118 B-5
IC103 C-l D119 c-5
.lLJuL nn IC104 C-6 D120 A-4
IC.105 C-B D413 A-8
4.7VP-P (V 1 5 V P - P (H 1 5 V P - P (4MHz 1 IC352 B-1 2 D432 84
lC354 B-1 2 D433 G8
lC355 B-10 D434 C8
IC431 c7 D504 G-9
O4-u4 0, \ \ IC501 E.7 D505 F-9
IC601 E-2 D506 G-9
-L-c-- IC602 F-2 D507 E-11
IC605 E-2 D508 E-11
IC606 F.2 D509 E-11
3.5VP-P (V 1 3.8Vp-P (VI 28 VP-P ( V 1 IC607 F-5 D510 F-10
D511 F-10
D512 E-8
YRANSISTOR D515 E-9
D516 B-5
QlOl E-5
0517 c.5
0103 A-2
D601 G-2
Q104 A-3
Y!Yu-L”--Lk ?--r-m Q105 A-4 D602 G-2
D603 G-4
7 V P - P (H 1 2 8 0 V P - P (H 1 18Vp-P (H 1 Q106 A-3
D604 G-5
4107 A-9
D605 66
QlO8 A-8
D606 G-6
QlO9 G5
@ 0 8 D607 E-4
4122 C-7
D608 E-4
Q344 A-9
Q345 B-10 D609 E-3
D610 E-3
fis%J%- Q346 B-10
0611
Q434 B-9 E-6
900 V P - P (H 1 1 . 9 V P - P (H 1 1.9Vp-p (H 1 Q435 B-10 D612 E-4
D613 D-4
Q436 B-9
4437 B.9 D614 E-5
D615 E-5
@ 8 @ Q438 B-9
D616 E-5
Q439 B9
D617 E-5
Q501 G7
D618 E-5
Q502 G-10
lr-d=-L lJwd=L lP-lJ=l Q503 D619 E-6
F-6
D620 F-2
Q504 D-5
0 . 9 V P - P (H 1 1.9Vp-p (H 1 0.95 V P - P (H 1 4505 D5 D621 F-5
D622 G-4
4601 G-4
Q602 G-6
@ 0 @ 4603 F-3 VARIABLE
Q604 E-6 RESISTOR
4605 D-6 RVlOl B-3
lmh?-l lm-@h lF@%=-L Q606 D-6
4610 D-4
Q613 F-6
I .95 V P - P ( H 1 1.9Vp-p (H 1 1 . 2 V P - P (H 1 4614 F.6
DIODE
DlOl D-10
D103 A-2
0104 G3
D106 D3
0107 Dl
D108 C-l
D109 A-4
DllO A.5
Dlll A-5
D112 c-5
D113 c-3
D114 C-3
NOTE:
I
The circuit indicated as left contains high voltage of over
600 Vp-p. Care must be paid to prevent an electric shock in
inspection or repairing.
m
r - r - -
- 4 9 -