5, Heat Treatment
51 lleaings shall weve «heat treatment proper to tir
design and cheial companion.
52 Castings shall be fumished in the normalized and
tempered cadtons; Gras WC}, WC#, WES, WCB, and
CATS shal tempest HOO" [595°C] min: Gras C9,
(65, C12, and WCT shal be tempered at 1250 [678°C min
Grade C120 shall be tempered at [380° [73°C] min
5.3 Heat teatment sll be perfirmed aller casings have
teen allowed to coo below the transformation range.”
6 Chemical Composition
6:1 The sect sll conform to the requirements a6 0
chemical eampostion peseied in Table T Note 8)
Non 47 of ain lone deveoet 0 Gade
Haan cxenely mest. Van Chet ee
Mechs crhoaiin te ft ah. V anps
sin stall re of adhering wind, le, rach, a ote,
‘Other sucface discorinuties shall meet the vial aceplance
Sands specilied i the exer. Practice A SODA 802M oF
‘ther sisal standards may he wo define aeeplalesrlace
scontinitis and inh. Craccepable visual ssface discon
lines stall be removed and thee removal vee by sou
‘cuaninaion ofthe estan eaviics, When methods involving.
high temperature are sed inthe removal of acomtniien,
casings salle pcbeated tat asthe enna tempers
tures in Table 3
1S Whon ational ingpection is dese, Supplementary
Reguinemenis $3, $5, and SIO may be oer
183 The casings shll not be peened, puget or impr
rated w sop leaks
9. Repair by Welding
9.1 Repairs shall be mde using procedures and welders
‘qualified tinder Practice A S884 488M
‘TABLE 1 Choma! Requrements
onset.
a
TRETET ver nce were ce eth ce cm SER
Were “Sasowe Geboio GWEN Germ Geom omen Gaon dies Lusow tap
Sr’ Ske ikke Bhs Ele als Soe Seas Sa
Sionin Gleam Saest Sens Gabaes OIG omae Seam aI Siete See
Sooper Sse
“Sara Rauaa EameoTABLE? Tense Requiemente
oe cegh Sewn ee
my Ten
ver eigen ee
=
veggies ies mem mm
vn alge mpm ee
‘
rr
crayon alana mw
‘a,
ows aingieys sen ew
re
en ht re me ed eae ang ped Sesion
AMAR Tush aj gh seston dirs ah a
9.2 Weld repairs shll be inspected to the same quality
sundae sed inspect the etstings, When castings
te produced wit Supplementary Raguirement $4 specified,
‘rol repairs shall be tapeted by magnetic parce examina
Sion wo the sume anda thi are used wo inspect the castings.
‘When eastings are prosuced ith Supplementary Reiremen
SS specified, weld sepa on casings that have leaked o#
Inydiostatie es or on casings in which the depth any eaviy
ropa frrepair welding exceeds 20 of the wall thickness
{rie [25 nm, whichever sama, o meanings in which
any cavity prepued for welding is greater han appronimately
oes ocean PEE
re
wor Tae Sim
et 2030
wee 2 Seo a]
wee a patted
Wes a Soa
vet a 0 (1
oe. a Soil
Beeumem Si
ee a sf
10 in [65 cr shal he eatiograpd to the same stands
that ate use to laspee he easing.
‘9.3, Wel puis sll be considered mjor in de ewe of &
ating hi hs leaked on hydrostatic tes when the depth of
the cavity prepared for welling exceeds 20% of the wall
thickness of Tin. [25 mm whichever is smaller. gr when the
extent ofthe cavity exceeds approximately 10 in [68 em
All castings with major repair welds shal be thermally tess
relicved or completely reheat-ueated, This mandatory sts
rele? or reel teatment shall be in aocordunce wilh he
(qualified peeceire used. Major reais shall be inspected 1
the sabe quality standard that are used inspec the castings.
10, Keywords
HO alloy see; high-empentur;
Meck: pressure-coniining: ste castings