Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Siemens AG
Power Transmission and
Distribution Group
Power Systems and
Energy Management Division
Power
Hofmannstrasse 51
D-81359 Munich
www.ev.siemens.de to the 7 VR 56
Siemens Aktiengesellschaft Subject to change without prior notice Order No.: E50001-U336-A18-X-7600
Printed in Germany
Dispo-Stelle 06401
61U1279 W 336502 PA 06972.5
FWT 2000i
a modular, flexible system for telecontrol
and data transmission
2 3
FWT 2000i
a modular, flexible system for telecontrol
and data transmission
2 3
System characteristics:
4 5
System characteristics:
4 5
ZWU, line V
switchover KS
I
S
ZWU/LU
II
KU1
E
I
II
Alternative path switching KU1 Data transmission in the voice band Compatibility
E with SEU 2000i
For the transmission of important data, The FWT 2000i System is fully com-
transmission paths are frequently dupli- P I The SEU 2000i module comprises a patible with the predecessor system
S I K1
cated. On the send side, the signal is transmitter and receiver for transmitting FWT 2000 and can be operated with
applied to two paths. On the receive P II a data channel via a 2-wire or 4-wire line other VFT systems.
side, switchover from the main path to S II K2 in the voice band from 300 to 3400 Hz. The FWT 2000i modules also operate
the standby path takes place in the Due to the fact that signal processing in the module frames of the
event of a fault. This function is per- is less complex, this module offers an FWT 2000 System.
UM KU2
formed by the alternative path switching economical alternative in cases where
module (ZWU). SP flexibility is limited. The modules of the old FWT 2000
W II KU2 System also operate in the module
The systems internal switchover criteria The SEU 2000i module is identical to frames of the new FWT 2000i
are the: the KS 2000i Channel Unit. System.
Receive level; Since the pin assignment is the same,
the SEU 2000i can be installed The KS 2000i Channel Unit can be
Signal-to-noise ratio. wherever a KS 2000i can be installed installed in any module adapter in
Either of these criteria alone or the two (e.g. adapter module in telecontrol which the KS 2000 can be installed.
together can result in switchover. ZWU, channel switchover KS units). The SEU 2000i can be installed in any
Users can determine the switchover In contrast to the KS 2000i, only 4 fre- module adapter in which the KS 2000i
threshold within a wide range. S I quencies can be set on the SEU 2000i. or KS 2000 can be installed.
In addition to the systems internal The first two frequencies are identical Due to its flexible setting options, the
ZWU/ LU
switchover criteria, switchover can also to those of the earlier SEU A,B/ST KS 2000i Channel Unit operates in
be controlled externally, e.g. by the modules. The second frequency pair conjunction with all VFT systems.
telecontrol unit. KU1 E I makes it possible to transmit a
The alternative path switching module 1200 baud duplex channel via a two-
permits the selection of line (LU) or wire cable connection.
channel (KU) switchover. Transmission The SEU 2000i was designed with a
path priority is determined by means of view to possible advantages for users,
KU1
a front connector. KS including economical system manage-
ment, transmission security and
Control frequency transmission for S reliability and short process cycle
II
multi-station control systems times, as well as easy handling.
The audio-frequency multi-station
control system is a special type of tele-
control system. It is used, for example, P I E II
for changing meter rates and for con- K1
S I
trolling street and traffic lights. P II
The audio-frequency multi-station K2 S II
control converter (TRU) converts the
control frequency signals for transmit- KU2 UM
ting the multi-station control frequency. SP
The signal is output on a VFT transmitter W II
via a V.28 interface. In this way, the KU2
control frequency is routed to the cor-
responding station using a minimum of
frequency space. A VFT receiver routes
the control frequency signal to the TRU
receiver unit, which contains a control
frequency filter. This filter greatly Schematic scheme of control frequency transmission
reduces the jittering that interferes Integrated control
with multi-station control. Thus, a frequency filter
control frequency of the best possible
quality is supplied to the multi-station ( ) TRU S E TRU
( )
control command unit in the substation. Control
frequency
S S
Data
E E
Data
6 7
ZWU, line V
switchover KS
I
S
ZWU/LU
II
KU1
E
I
II
Alternative path switching KU1 Data transmission in the voice band Compatibility
E with SEU 2000i
For the transmission of important data, The FWT 2000i System is fully com-
transmission paths are frequently dupli- P I The SEU 2000i module comprises a patible with the predecessor system
S I K1
cated. On the send side, the signal is transmitter and receiver for transmitting FWT 2000 and can be operated with
applied to two paths. On the receive P II a data channel via a 2-wire or 4-wire line other VFT systems.
side, switchover from the main path to S II K2 in the voice band from 300 to 3400 Hz. The FWT 2000i modules also operate
the standby path takes place in the Due to the fact that signal processing in the module frames of the
event of a fault. This function is per- is less complex, this module offers an FWT 2000 System.
UM KU2
formed by the alternative path switching economical alternative in cases where
module (ZWU). SP flexibility is limited. The modules of the old FWT 2000
W II KU2 System also operate in the module
The systems internal switchover criteria The SEU 2000i module is identical to frames of the new FWT 2000i
are the: the KS 2000i Channel Unit. System.
Receive level; Since the pin assignment is the same,
the SEU 2000i can be installed The KS 2000i Channel Unit can be
Signal-to-noise ratio. wherever a KS 2000i can be installed installed in any module adapter in
Either of these criteria alone or the two (e.g. adapter module in telecontrol which the KS 2000 can be installed.
together can result in switchover. ZWU, channel switchover KS units). The SEU 2000i can be installed in any
Users can determine the switchover In contrast to the KS 2000i, only 4 fre- module adapter in which the KS 2000i
threshold within a wide range. S I quencies can be set on the SEU 2000i. or KS 2000 can be installed.
In addition to the systems internal The first two frequencies are identical Due to its flexible setting options, the
ZWU/ LU
switchover criteria, switchover can also to those of the earlier SEU A,B/ST KS 2000i Channel Unit operates in
be controlled externally, e.g. by the modules. The second frequency pair conjunction with all VFT systems.
telecontrol unit. KU1 E I makes it possible to transmit a
The alternative path switching module 1200 baud duplex channel via a two-
permits the selection of line (LU) or wire cable connection.
channel (KU) switchover. Transmission The SEU 2000i was designed with a
path priority is determined by means of view to possible advantages for users,
KU1
a front connector. KS including economical system manage-
ment, transmission security and
Control frequency transmission for S reliability and short process cycle
II
multi-station control systems times, as well as easy handling.
The audio-frequency multi-station
control system is a special type of tele-
control system. It is used, for example, P I E II
for changing meter rates and for con- K1
S I
trolling street and traffic lights. P II
The audio-frequency multi-station K2 S II
control converter (TRU) converts the
control frequency signals for transmit- KU2 UM
ting the multi-station control frequency. SP
The signal is output on a VFT transmitter W II
via a V.28 interface. In this way, the KU2
control frequency is routed to the cor-
responding station using a minimum of
frequency space. A VFT receiver routes
the control frequency signal to the TRU
receiver unit, which contains a control
frequency filter. This filter greatly Schematic scheme of control frequency transmission
reduces the jittering that interferes Integrated control
with multi-station control. Thus, a frequency filter
control frequency of the best possible
quality is supplied to the multi-station ( ) TRU S E TRU
( )
control command unit in the substation. Control
frequency
S S
Data
E E
Data
6 7
Technical data
Optimal security and reliability Power supply for the entire input 50 Bd 50 Bd 100 Bd 100 Bd 200 Bd 200 Bd 600 Bd 1200Bd 2400Bd
Users demands for operational voltage range SB FM 120 SB FM 240 SB FM 480
security and reliability are met by the Only two power supply modules are Nominal signaling speed Bd 50 50 100 100 200 200 600 1200 2400
following special features of the required for the entire input voltage
FWT 2000i System: range of 2460 V DC or 110220 V DC Maximum signaling speed Bd 50 75 100 150 200 300 600 1200 2400
The effects of temperature and aging and 110230 V AC. Frequency shift Hz 22.5 30 45 60 90 120 200 400 800
are practically eliminated by the use of One power supply module is required Send/receive level, nominal,
digital signal processors. for the following input voltage range: value per channel dBm 24.5 22.5 21.5 19.5 18.5 16.5 13.5 10.5 7.5
The power supply concept permits 24/48/60 V DC.
Minimum frequency band width Hz 90 120 180 240 360 480 1100 1700 3100
secondary voltages of 12 V from two The second power supply module is
power supply units to be connected used for the following input voltage Inherent distortion (text)
in parallel. range: 110220 DC and 110230 V AC. for nominal % <4 <3 <4 <3 <4 <3 <3 <4 < 12
signaling speed
The power supply units can also be fed
with different primary voltages. KS 2000i Channel Unit for battery Approx. signal transfer delay **) ms 48 35 26 20 15 10 4,5 3,5 2,5
The receiver unit monitors the level connection Approx. operate delays of level monitor (P)**)ms 30 23 15 12 7.5 6.5 2.5 2.0 1.5
and the signal-to-noise ratio. On request, the KS 2000i Channel Unit Number of
When transmission ratios worsen, can be equipped with a voltage regula- channels in a frequency
a prealarm is activated. tor for connection to a 2460 V battery. band of 0.3 bis 7.2 76 57 38 28 19 14 8 4 2
When there is no guarantee of data In order to prevent interference with
adjacent system components, the Maximum deviation of VFT
security, the output is applied to frequencies Hz 0.1
continuous potential, thus preventing voltage regulator is radio-interference-
the system from outputting incorrect suppressed to Class B. Frequency range kHz 0.3...7.2
data. In addition to the system features Raster of adjustable channel
The local circuit to the VFT transmitter described above, the FWT 2000i mid-frequencies Hz 30
is monitored for interruptions. In the System provides all users with the
cost-effective and technical benefits Maximum deviation of
event of an interruption, the receiver is
expected and required when this send level dB 0.5
set to continuous polarity in order to referred to set value
prevent the output of incorrect data. system is used.
An economical stocking of spare parts Operating range of receiver,
Voltage-carrying modules can be referred to nominal channel level dBr 20...+ 10
inserted and removed, thus permitting is possible since only one module is
all the other modules to remain needed for all rates and frequencies. Send level adjustment
in operation. The system can be placed in service in 2 dB steps referred dBr 22...+ 18
quickly and easily thanks to automatic to nominal level
The secondary voltage can be supplied
to the alternative path switching level adjustment and automatic com- Display of receive level referred,
module from two power supply units. pensation of distortion. to nominal channel level 8 V at RL socket, in accordance with 0 dBr
The use of the latest digital processors Threshold value of receiver
and components ensures that the level monitor dBr adjustable from 2510 in steps of 1 dB
system will have a long service life referred to nominal level
and a high rate of availability.
Threshold value of signal
monitor (S), adjustable in steps,
in accordance with
telegraphic distortion of % ca. 20, 30
KS 2000i
Neutral setting automatically
sets 1:1 signaling, initialized
via pushbutton in range % 25
S The relevant ITU-T recommendations
apply to FM 120, FM 240,
and FM 480 systems
*) Please observe level control for multi-channel operation
E **) Receive filter without increased suppression loss
+/ 12 V
24 V DC
48 / 60 V DC
Optimal security and reliability Power supply for the entire input 50 Bd 50 Bd 100 Bd 100 Bd 200 Bd 200 Bd 600 Bd 1200Bd 2400Bd
Users demands for operational voltage range SB FM 120 SB FM 240 SB FM 480
security and reliability are met by the Only two power supply modules are Nominal signaling speed Bd 50 50 100 100 200 200 600 1200 2400
following special features of the required for the entire input voltage
FWT 2000i System: range of 2460 V DC or 110220 V DC Maximum signaling speed Bd 50 75 100 150 200 300 600 1200 2400
The effects of temperature and aging and 110230 V AC. Frequency shift Hz 22.5 30 45 60 90 120 200 400 800
are practically eliminated by the use of One power supply module is required Send/receive level, nominal,
digital signal processors. for the following input voltage range: value per channel dBm 24.5 22.5 21.5 19.5 18.5 16.5 13.5 10.5 7.5
The power supply concept permits 24/48/60 V DC.
Minimum frequency band width Hz 90 120 180 240 360 480 1100 1700 3100
secondary voltages of 12 V from two The second power supply module is
power supply units to be connected used for the following input voltage Inherent distortion (text)
in parallel. range: 110220 DC and 110230 V AC. for nominal % <4 <3 <4 <3 <4 <3 <3 <4 < 12
signaling speed
The power supply units can also be fed
with different primary voltages. KS 2000i Channel Unit for battery Approx. signal transfer delay **) ms 48 35 26 20 15 10 4,5 3,5 2,5
The receiver unit monitors the level connection Approx. operate delays of level monitor (P)**)ms 30 23 15 12 7.5 6.5 2.5 2.0 1.5
and the signal-to-noise ratio. On request, the KS 2000i Channel Unit Number of
When transmission ratios worsen, can be equipped with a voltage regula- channels in a frequency
a prealarm is activated. tor for connection to a 2460 V battery. band of 0.3 bis 7.2 76 57 38 28 19 14 8 4 2
When there is no guarantee of data In order to prevent interference with
adjacent system components, the Maximum deviation of VFT
security, the output is applied to frequencies Hz 0.1
continuous potential, thus preventing voltage regulator is radio-interference-
the system from outputting incorrect suppressed to Class B. Frequency range kHz 0.3...7.2
data. In addition to the system features Raster of adjustable channel
The local circuit to the VFT transmitter described above, the FWT 2000i mid-frequencies Hz 30
is monitored for interruptions. In the System provides all users with the
cost-effective and technical benefits Maximum deviation of
event of an interruption, the receiver is
expected and required when this send level dB 0.5
set to continuous polarity in order to referred to set value
prevent the output of incorrect data. system is used.
An economical stocking of spare parts Operating range of receiver,
Voltage-carrying modules can be referred to nominal channel level dBr 20...+ 10
inserted and removed, thus permitting is possible since only one module is
all the other modules to remain needed for all rates and frequencies. Send level adjustment
in operation. The system can be placed in service in 2 dB steps referred dBr 22...+ 18
quickly and easily thanks to automatic to nominal level
The secondary voltage can be supplied
to the alternative path switching level adjustment and automatic com- Display of receive level referred,
module from two power supply units. pensation of distortion. to nominal channel level 8 V at RL socket, in accordance with 0 dBr
The use of the latest digital processors Threshold value of receiver
and components ensures that the level monitor dBr adjustable from 2510 in steps of 1 dB
system will have a long service life referred to nominal level
and a high rate of availability.
Threshold value of signal
monitor (S), adjustable in steps,
in accordance with
telegraphic distortion of % ca. 20, 30
KS 2000i
Neutral setting automatically
sets 1:1 signaling, initialized
via pushbutton in range % 25
S The relevant ITU-T recommendations
apply to FM 120, FM 240,
and FM 480 systems
*) Please observe level control for multi-channel operation
E **) Receive filter without increased suppression loss
+/ 12 V
24 V DC
48 / 60 V DC
1 2xE C
3xE D
4xE E
57.15
132
132
5xE F
6xE G
7xE H
8xE J
9xE K
10xE L
84TE=426.72 Without TRU 0 X
465.1
1xTRU 1
2xTRU 2
3xTRU 3
10 11
Order data 6 7 8 9 10 11 12 13 14 15 16 17
Order specifications for FWT 2000i to MLFB Order number: 7VR60 X
All sections of the order specification
form must be filled out to order
an assembled FWT 2000i System
1 2xE C
3xE D
4xE E
57.15
132
132
5xE F
6xE G
7xE H
8xE J
9xE K
10xE L
84TE=426.72 Without TRU 0 X
465.1
1xTRU 1
2xTRU 2
3xTRU 3
10 11
Power Network Telecommunication
FWT 2000i System for Telecontrol
and Data Transmission
Siemens AG
Power Transmission and
Distribution Group
Power Systems and
Energy Management Division
Power
Hofmannstrasse 51
D-81359 Munich
www.ev.siemens.de to the 7 VR 56
Siemens Aktiengesellschaft Subject to change without prior notice Order No.: E50001-U336-A18-X-7600
Printed in Germany
Dispo-Stelle 06401
61U1279 W 336502 PA 06972.5