Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Pantalla anterior
Bienvenido: r120lb2
SEHS96150001
Introduction
This manual provides the necessary information on how the DT and HD family of connectors (shown in
Illustration 1) are properly serviced.
Do not perform any procedure, outlined in this manual, or order any parts until you read and understand the
information contained within.
Deutsch HD and DT style connectors are very similar. Differing only in shape and color, the function and
servicing techniques are the same. Both consist of a plug and receptacle.
Illustration 1. Typical DT
(1) And HD
(2) Style Connectors.
Gray colored DT style connectors were changed in mid-1999 to improve the replaceable seal between the plug
and receptacle. For easy recognition, the most current DT style connector plugs and receptacles found in this kit
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 2 de 18
will be colored black. The current green wedge design will also be easily identified from the former orange
color.
The plug half of the DT style connector has a seal at the mating end. This seal has been improved on black
connectors to help prevent slipping and is replaceable. This improvement will help keep moisture and dirt from
entering the connector. The current seal design (2, Illustration 2) is not interchangeable with the former design
(1, Illustration 2). The receptacle has also changed to the new colors.
Illustration 2. Seal Designs. (1) Former Seal On Gray Plug. (2) Current Seal On Black Plug.
The Pin and Socket terminal crimping procedure (shown on page 8) is identical for both HD and DT style
connectors.
Receptacles accept pin terminals. Wedges, assembled at the mating interface, lock the terminals into position.
The original orange wedges are now green and fit into the current black connectors. Plugs accept sockets.
Wedges lock the sockets into position. Green and orange receptacle wedges are interchangeable (refer to the
"DT Style Connector Compatibility" section in this manual for additional information). DT style connectors are
joined by aligning the latching mechanisms and pushing the connectors together.
HD style connectors are easily recognizable, by the round connector bodies. HD style connectors are sealed
with rubber gaskets, which are not replaceable. Wedges are not required with this design. The connectors are
joined using a quarter-turn locking ring.
Serviceable Parts
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 3 de 18
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 4 de 18
Service Kits
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 5 de 18
NOTE: The 175-3700 DT Style Field Service Group and the 190-8900 HD Style Deutsch Connector Group do
not contain the 1U-5804 Crimp Tool. The 1U-5804 Crimp Tool should be ordered separately.
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 6 de 18
The original gray colored DT style Deutsch connectors with orange wedges have been redesigned to improve
the plug and receptacle body sealing. The redesigned connectors are black with green wedges.
NOTE: The seals for the black and gray plugs are NOT interchangeable.
Use the information in the "Acceptable Color Combinations" section of this manual for acceptable
combinations of colors and parts when servicing DT style connectors.
Mating Pairs
Receptacle
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 7 de 18
Plug
Connector Unmating
No tools are required to unmate DT or HD style connectors.
NOTICE
The use of tools could damage the locking latch (DT) or ring (HD) and
prevent securely remating the connector.
1. Unmate the connector by grasping the plug and receptacle housings with each hand. The plug housing
contains the locking latch (DT) or locking ring (HD).
2. On DT style connectors, completely depress the locking latch to separate the connector housings.
NOTE: If there is dirt build-up under the latch (DT), tap the side of the connector, dislodging the dirt particles,
until the latch can be fully depressed.
3. With the latch fully depressed, pull the plug from the receptacle.
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 8 de 18
4. The larger DT style connectors are unmated in the same manner as the smaller ones, except they have two
locking latches.
5. On HD style connectors, grasp the locking ring on the plug body and rotate the ring counterclockwise. This
action will unlock and force the connector bodies apart.
NOTICE
DO NOT pull on the wires to separate the two halves of any connector.
This can cause damage to both the wires and connectors.
Terminal Removal
Plug Housing
The DT style connectors use a wedge to secure the socket and pin terminals. This wedge must first be removed
before terminals are separated from the connector.
1. Remove the wedge by inserting 147-6456 Wedge Removal Tool between the wedge and connector housing.
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 9 de 18
NOTICE
When removing the wedge, insert the removal tool along the side of the
wedge, not the corners, which could cause damage
2. With the wedge removed, place 147-6456 Wedge Removal Tool against the terminal locking finger. Push the
finger away from the terminal while gently pulling the wire out of the connector.
Receptacle Housing
1. Remove the terminals from the connector by first removing receptacle wedge (2), as shown in Illustration 15.
Remove wedge (2) by grasping it with long nose pliers and pulling straight out.
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 10 de 18
2. The receptacle wedge, in other than 3-pin connector configurations, is removed by inserting one end of 147-
6456 Wedge Removal Tool into the center of the wedge and hooking the outside edge.
3. Hold the receptacle in one hand and apply upward pressure on 147-6456 Wedge Removal Tool with the
opposite hand. Pull the wedge straight out.
4. With the wedge removed, place the 147-6456 Wedge Removal Tool against the terminal locking finger. Push
the finger away from the terminal while gently pulling the wire out of the connector.
Illustration 18. Removing Terminals Using The 151-6320 Pin/Socket Removal Tool.
2. Firmly push the removal tool inward until it disengages the terminal locking fingers.
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 11 de 18
3. Remove the terminal, wire, and removal tool together from the connector body.
2. Strip 6.4 to 7.0 mm (.25 to .31 in) of insulation from the wire being careful not to cut or nick the copper wire
strands. A properly stripped wire will bottom out in the terminal with the insulation 1.5 mm (.06 in) from the
end of the terminal. On the socket terminal, the wire is inserted into the end with inspection hole (M).
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 12 de 18
3. Make sure the wire selector gauge (G, Illustration 20) on 1U-5804 Crimp Tool is set to the wire size being
crimped. If the wire selector gauge is properly set, proceed to Step 4. If the selector gauge setting does not
match the wire size being crimped, proceed as follows:
b. Raise selector knob (J) and rotate it until the arrow is aligned with the wire size to be crimped.
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 13 de 18
(K) Locknut.
(L) Adjusting Screw.
4. Loosen locknut (K) and turn adjusting screw (L) in until it stops.
(K) Locknut.
(L) Adjusting Screw.
5. Insert terminal (6) and turn adjusting screw (L) until the wire/crimp end of the terminal is flush with the tool
face. Tighten locknut (K).
6. Insert the wire into the terminal (the terminal must be centered between crimp fingers). Make sure that all
wire strands are in the crimp barrel.
7. Crimp the wire in the terminal by squeezing the handles of the crimp tool together until the handle hits the
stop and automatically releases.
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 14 de 18
9. Inspect the terminal to make sure that all wire strands are in the crimped barrel and that the crimp indent falls
in the center of the terminal crimp barrel.
Illustration 25. Inspect The Terminal. Good Quality Crimp, Correctly Positioned.
Terminal Insertion
1. Grasp the wire approximately 25 mm (1.0 in) from the crimped terminal. Insert the terminal into the
connector, as shown in Illustrations 27 and 29.
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 15 de 18
2. Push the terminal straight into the connector until the terminal locks in place. A slight tug on the wire will
confirm the terminal is properly locked in place.
4. After all the terminals have been assembled into the receptacle/plug housing, insert the wedge (long nose
pliers may be required to insert some receptacle wedges). Make sure the wedge snaps completely into place.
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 16 de 18
Connector Cleaning
Connectors that have been unmated for service purposes must be cleaned before reconnecting.
NOTICE
The interior mating surfaces of the connector (i.e. terminals, seals, and insulators) should be cleaned using a
cotton swab and denatured alcohol.
Use all cleaning solutions with care and in a well ventilated area. Always
wear eye protection when using cleaning solutions. Failure to follow the
precautions provided by the manufacturer on using, storing and
disposing of any cleaning solution can result in bodily injury.
Connector Mating
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 17 de 18
1. DT style connectors are mated by grasping each half of the connector and aligning the locking latch of the
plug housing with the receptacle housing.
NOTE: For the 8 and 12-pin connector, it may be necessary to rotate the plug housing 180 degrees in order to
achieve the correct alignment.
2. Push the two connector halves together until the latch(es) lock into place.
3. Make sure the connector housings are locked together by attempting to pull the housings apart.
4. HD style connectors are mated by aligning the external alignment marks (1), pushing the two connector
bodies together, and then turning the locking ring 1/4 turn clockwise until the ring clicks into the locked
position.
For information on service tools or shop supplies, contact Caterpillar Service Technology Group on:
or
12:42:37 17-12-2014
Sistema de Informacin de Servicio Pgina 18 de 18
Copyright 1993 - 2014 Caterpillar Inc. Wed Dec 17 12:41:00 UTC-0300 2014
Todos los derechos reservados. r120lb2
Red privada para licenciados del SIS.
12:42:37 17-12-2014