Documentos de Académico
Documentos de Profesional
Documentos de Cultura
K ELECTRICAL
B
SECTION
LIGHTING SYSTEM C
E
CONTENTS
PRECAUTION ............................................................ 3 Wiring DiagramR/FOG .................................... 16 F
Precautions for Supplemental Restraint System Bulb Replacement .................................................. 17
(SRS) AIR BAG and SEAT BELT PRE-TEN- Removal and Installation ........................................ 17
SIONER .................................................................. 3 REMOVAL ........................................................... 17 G
Precaution ................................................................ 3 INSTALLATION ................................................... 17
Wiring Diagrams and Trouble Diagnosis .................. 3 TURN SIGNAL AND HAZARD WARNING LAMPS... 18
HEADLAMP ................................................................ 4 System Description ................................................. 18
H
System Description .................................................. 4 TURN SINGAL OPERATION .............................. 18
DESCRIPTION ...................................................... 4 HAZARD LAMP OPERATION ............................. 18
LOW BEAM OPERATION ..................................... 4 Wiring Diagram TURN ................................... 20
HIGH BEAM OPERATION/FLASH-TO-PASS Trouble Diagnoses ................................................. 22 I
OPERATION ......................................................... 4 Electrical Components Inspection .......................... 22
Wiring Diagram H/LAMP ................................. 5 COMBINATION FLASHER UNIT CHECK ........... 22
Trouble Diagnoses ................................................... 6 Bulb Replacement .................................................. 22 J
Aiming Adjustment ................................................... 6 RemovalandInstallation for Front Turn SignalLamp... 23
LOW BEAM ........................................................... 7 REMOVAL ........................................................... 23
Bulb Replacement .................................................... 7 INSTALLATION ................................................... 23
LT
HEAD LAMP ......................................................... 7 Removal and Installation for Rear Turn Signal Lamp... 23
CLEARANCE LAMP ............................................. 8 LIGHTING AND TURN SIGNAL SWITCH ................ 24
Removal and Installation .......................................... 8 Removal and Installation ........................................ 24
REMOVAL ............................................................. 8 Switch Circuit Inspection ........................................ 24 L
INSTALLATION ..................................................... 8 HAZARD SWITCH .................................................... 25
HEADLAMP AIMING CONTROL ............................... 9 Removal and Installation ........................................ 25
Wiring Diagram-H/AIM- ............................................ 9 REMOVAL ........................................................... 25 M
FRONT FOG LAMP .................................................. 10 INSTALLATION ................................................... 25
System Description ................................................ 10 PARKING, LICENSE AND TAIL LAMPS .................. 26
DESCRIPTION .................................................... 10 Wiring Diagram TAIL/L .................................. 26
FOG LAMP OPERATION .................................... 10 Bulb Replacement .................................................. 28
Wiring Diagram F/FOG (LHD) ........................11 PARKING AND TAIL LAMPS .............................. 28
Wiring DiagramF/FOG(RHD) ............................. 12 LICENSE PLATE LAMP ...................................... 28
Aiming Adjustment ................................................. 13 Removal and Installation ........................................ 28
Bulb Replacement .................................................. 13 PARKING AND TAIL LAMPS .............................. 28
Removal and Installation ........................................ 14 LICENSE PLATE LAMP ...................................... 28
REMOVAL ........................................................... 14 BACK-UP LAMP ....................................................... 29
INSTALLATION ................................................... 14 Wiring Diagram BACK/L ................................ 29
REAR FOG LAMP .................................................... 15 Bulb Replacement .................................................. 30
System Description ................................................ 15 Removal and Installation ........................................ 30
DESCRIPTION .................................................... 15 REAR COMBINATION LAMP ................................... 31
FOG LAMP OPERATION .................................... 15 Wiring Diagram STOP/L .................................. 31
LT-1
Bulb Replacement .................................................. 32 LUGGAGE ROOM LAMP .........................................42
Removal and Installation ........................................ 32 Wiring DiagramINT/L .......................................42
REMOVAL ........................................................... 32 Bulb Replacement ...................................................43
INSTALLATION .................................................... 32 Removal and Installation .........................................43
INTERIOR ROOM LAMP .......................................... 33 ILLUMINATION ..........................................................44
Wiring Diagram ROOM/L /Standard Size Inte- System Description .................................................44
rior Lamp (Standard Roof) ...................................... 33 Wiring Diagram ILL ........................................45
Wiring Diagram ROOM/L/Big Size Interior Lamp ASHTRAY ILLUMINATION .......................................47
(Standard Roof) ...................................................... 36 Wiring Diagram .......................................................47
Wiring Diagram ROOM/L/With Interior Room Bulb Replacement Removal and Installation ..........47
Lamp Switch(Hi Roof) ............................................. 38 BULB SPECIFICATIONS ..........................................48
Bulb Replacement .................................................. 40 Headlamp ................................................................48
INTERIOR ROOM LAMP .................................... 40 Exterior Lamp ..........................................................48
SPOT LAMP ........................................................ 40 Interior Lamp/Illumination ........................................48
Removal and Installation ........................................ 40
INTERIOR ROOM LAMP .................................... 40
SPOT LAMP ........................................................ 41
LT-2
PRECAUTION
PRECAUTION PFP:00011
A
Precautions for Supplemental Restraint System (SRS) AIR BAG and SEAT
BELT PRE-TENSIONER EKS002YC
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along B
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SRS and SB section of
this Service Manual. C
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer. D
Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section. E
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow harness connectors.
F
Precaution EKS002QG
Do not touch the glass of bulb directly by hand. Keep grease and other oily matters away from it. Do not
touch bulb by hand while it is lit or right after being turned off. Burning may result. G
Do not leave bulb out of headlamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of the headlamp. When replacing the bulb, be sure to replace it with a new one.
Adjust aiming by tightening aiming screw. (To adjust it toward loosening side, first loosen adjusting screw, H
and then make adjustment by tightening.)
To remove soil or sealant of bulbs, do not use organic solvent (thinner, gasoline, etc.)
When replacing bulb, be sure to hold bulb socket and pull it out straight. If wiring harness of the bulb is I
pulled at an angle, the bulb may be caught in the lamp, making it difficult to take out.
Wiring Diagrams and Trouble Diagnosis EKS002YD
J
When you read wiring diagrams, refer to the followings:
Refer to GI-13, "How to Read Wiring Diagrams" in GI section
Refer to PG-2, "POWER SUPPLY ROUTING" for power distribution circuit in PG section LT
When you perform trouble diagnosis, refer to the followings:
Refer to GI-10, "HOW TO FOLLOW TEST GROUPS IN TROUBLE DIAGNOSES" in GI section
Refer to GI-23, "How to Perform Efficient Diagnosis for an Electrical Incident" in GI section L
LT-3
HEADLAMP
HEADLAMP PFP:26010
DESCRIPTION
The headlamps are controlled by the lighting switch which is built into the combination switch.
Power is supplied at all times
to lighting switch terminal 8
through 15A fuse (No. 44, located in the fuse and fusible link box), and
to lighting switch terminal 5
through 15A fuse (No. 41, located in the fuse and fusible link box).
LOW BEAM OPERATION
When the lighting switch is turned to the 2ND position and placed in LOW (B) position, power is supplied
from lighting switch terminal 10
to terminal 1 of the headlamp LH, and
from lighting switch terminal 7
to terminal 1 of the headlamp RH.
Terminal 3 of each headlamp supplies ground through body grounds H7 and H18.
With power and ground supplied, the low beams will illuminate.
HIGH BEAM OPERATION/FLASH-TO-PASS OPERATION
When the lighting switch is turned to the 2ND position and placed in HIGH (A) position or PASS (C) posi-
tion, power is supplied
from lighting switch terminal 6
to terminal 2 of headlamp RH, and
from lighting switch terminal 9
to terminal 2 of headlamp LH, and
to combination meter terminal 48(with tachometer) or 42(without tachometer) for the HIGH BEAM indica-
tor.
Ground is supplied to terminal 49(with tachometer) or 41(without tachometer) or of the combination meter
through body grounds M2 and M27(RHD Models), M2 and M49 and M121(LHD Models), M2 and M49 and
M121 and D2(LHD Models with power window).
Ground is supplide to terminal 3 of each headlamp through body grounds H7 and H18.
With power and ground supplied, the high beams and the HIGH BEAM indicator illuminate.
LT-4
HEADLAMP
LT
TKWH0101E
LT-5
HEADLAMP
When performing headlamp aiming adjustment, use an aiming machine, aiming wall screen or headlamp
tester. Aimers should be in good repair, calibrated and operated in accordance with respective operation man-
uals.
If any aimer is not available, aiming adjustment can be done as follows:
For details, refer to the regulations in your own country.
Keep all tires inflated to correct pressures.
Place vehicle and tester on one and same flat surface.
See that there is no-load in vehicle (coolant, engine oil filled up to correct level and full fuel tank) other
than the driver (or equivalent weight placed in driver's position).
LT-6
HEADLAMP
CAUTION:
Be sure aiming switch is set to "0" when performing aiming adjustment. A
LOW BEAM
1. Turn headlamp low beam on.
B
SKIA0798E
E
M
SEL254L
HEAD LAMP
1. Remove the headlamps. Refer to LT-8, "Removal and Installation"
2. Disconnect connector of headlamp.
3. Remove rubber cap.
4. Unlock retaining spring, then remove bulb.
Headlamp (High/Low) : 12V 60/55 W(H4)
SKIA0408E
LT-7
HEADLAMP
CLEARANCE LAMP
1. Remove the headlamps. Refer to LT-23, "Removal and Installation for Front Turn Signal Lamp"
2. Turn the RH bulbsocket clockwise and unlock it.
Turn the LH bulbsocket counterclockwise and unlock it.
3. Remove the bulb from its socket.
Clearance (Parking) lamp : 12V 5W
CAUTION:
Do not touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Do not touch bulb by hand while it is lit or right after being turned off. Burning may result.
Do not leave bulb out of headlamp reflector for a long time because dust, moisture smoke, etc.
may affect the performance of headlamp. When replacing bulb, be sure to replace it with new one.
When bulb is installed, be sure to lock rubber cap to ensure watertightness.
Removal and Installation EKS002QN
REMOVAL
1. Remove the sidecombination lamps. Refer to LT-23, "Removal
and Installation for Front Turn Signal Lamp"
2. Remove the front grille. Refer to EI-12, "FRONT GRILLE" in
"EXTERIOR & INTERIOR (EI)" section.
3. Remove the headlamp mounting bolts.
4. Pull the headlamp toward the front of the vehicle.
SKIA0409E
INSTALLATION
Install in the reverse order of removal, taking care of the following points.
Headlamp mounting screws and nut
Tightening torque : 4.5 - 6.4 N-m (0.45 - 0.65 kg-m, 39 - 56 in-lb)
LT-8
HEADLAMP AIMING CONTROL
LT
TKWH0141E
LT-9
FRONT FOG LAMP
DESCRIPTION
Power is supplied at all times to fog lamp relay terminal 5
through 15A fuse (No. 46, located in the fuse and fusible link box).
With the lighting switch in the 2ND position and LOW (B) position, power is supplied
through 10A fuse (No. 43, located in the fuse and fusible link box).
to lighting switch terminal 11
through terminal 12 of the lighting switch
to fog lamp relay terminal 1.
FOG LAMP OPERATION
The fog lamp switch is built into the combination switch. The lighting switch must be in the 1st or 2nd position
and LOW (B) position for fog lamp operation.
With the fog lamp switch in the ON position, ground is supplied
to fog lamp relay terminal 2
through the fog lamp switch and body grounds M2 and M27(RHD Models), M2 and M49 and M121(LHD
Models),M2 and M49 and M121 and D2.
The fog lamp relay is energized and power is supplied
from fog lamp relay terminal 3
to terminal 1 of each fog lamp.
Ground is supplied to terminal 2 of each fog lamp through body grounds M49, M121 and D2.
With power and ground supplied, the fog lamps illuminate.
LT-10
FRONT FOG LAMP
LT
TKWH0104E
LT-11
FRONT FOG LAMP
TKWH0146E
LT-12
FRONT FOG LAMP
A
1. Set the distance between the screen and the center of the fog
lamp lens as shown at left.
2. Remove front fog lamp rim. For detail, refer to BODY END in
BT section. B
3. Turn front fog lamps ON.
D
MEL327G
4. Adjust front fog lamps so that the top edge of the high intensity
E
zone is 100 mm (4 in) below the height of the fog lamp centers
as shown at left.
When performing adjustment, if necessary, cover the head-
lamps and opposite fog lamp. F
LT
MEL328G
LT-13
FRONT FOG LAMP
SKIA0626E
REMOVAL
1. Remove fog lamp mounting screw (2).
2. Pull out fog lamp from vehicle and disconnect connector.
SKIA0413E
INSTALLATION
Install fog lamp in the reverse order of removal, observing the tightening torque shown below.
Fog lamp mounting screw
Tightening torque :4.5 - 6.4 N-m (0.45 - 0.65 kg-m, 39 - 56 in-lb)
LT-14
REAR FOG LAMP
DESCRIPTION
Power is supplied at all times to fog lamp relay terminal 5 B
though 10A fuse (No.1, located in the fuse and fusible link box).
With the lighting switch in the 2ND position and LOW("B")position, power is supplied
though 10A fuse (No.43, located in the fuse and fusible link box). C
to lighting switch terminal 11
trough terminal 12 of the lighting switch
to fog lamp relay terminal 1. D
LT
LT-15
REAR FOG LAMP
TKWH0142E
LT-16
REAR FOG LAMP
A
1. Remove the lens mounting screws.
2. Remove the bulb.
Rear fog lamp 12V 21W B
REMOVAL
C
1. Remove the rear bumper. refer to EI-10, "REAR BUMPER"
2. Remove the lamp mounting bolts.
3. Disconnect connector and remove the lamp. D
F
SKIA1294E
INSTALLATION
Install fog lamp in the reverse order of removal. G
LT
LT-17
TURN SIGNAL AND HAZARD WARNING LAMPS
LT-18
TURN SIGNAL AND HAZARD WARNING LAMPS
LT
LT-19
TURN SIGNAL AND HAZARD WARNING LAMPS
TKWH0105E
LT-20
TURN SIGNAL AND HAZARD WARNING LAMPS
LT
TKWH0106E
LT-21
TURN SIGNAL AND HAZARD WARNING LAMPS
SEL122E
1. Remove the side combination lamp. Refer to LT-23, "Removal and Installation for Front Turn Signal Lamp"
LT-22
TURN SIGNAL AND HAZARD WARNING LAMPS
SKIA0426E
D
Removal and Installation for Front Turn Signal Lamp EKS002QY
REMOVAL
1. Loosen screws (1), then pull the front turn signal lamp toward
the front of the vehicle. E
SKIA0414E
H
INSTALLATION
Install front turn signal lamp in the reverse order of removal.
I
Removal and Installation for Rear Turn Signal Lamp EKS002QZ
LT
LT-23
LIGHTING AND TURN SIGNAL SWITCH
SKIA0059E
Using circuit tester, check continuity between the lighting and turn signal switch connector terminals in each
operation status of the switch.
Lighting switch is refer toLT-5, "Wiring Diagram H/LAMP "
Turn signal lamp switch is refer toLT-20, "Wiring Diagram TURN "
Front fog lamp switch is refer toLT-11, "Wiring Diagram F/FOG (LHD)"
Rear fog lamp switch is refer to
LT-24
HAZARD SWITCH
REMOVAL
1. Remove cluster lid C. Refer to IP-3, "INSTRUMENT PANEL
B
ASSEMBLY" .in INSTRUMENT PANEL (IP) section.
2. Using a flat-bladed screwdriver or other suitable tool, press pawl
to remove hazard switch from cluster lid C.
C
SKIA0418E
E
INSTALLATION
Installation is in the reverse order of removal.
F
LT
LT-25
PARKING, LICENSE AND TAIL LAMPS
TKWH0102E
LT-26
PARKING, LICENSE AND TAIL LAMPS
LT
TKWH0010E
LT-27
PARKING, LICENSE AND TAIL LAMPS
Installation
Install license plate lamp in the reverse order of removal, observing the tightening torque shown below.
License plate lamp mounting screws
Tightening torque :1.0 - 1.8 N-m (0.10 - 0.19 kg-m, 9-16 in-lb)
LT-28
BACK-UP LAMP
LT
TKWH0012E
LT-29
BACK-UP LAMP
LT-30
REAR COMBINATION LAMP
LT
TKWH0011E
LT-31
REAR COMBINATION LAMP
SKIA0801E
SKIA0416E
REMOVAL
1. Remove the body side trim. Refer to EI-22, "BODY SIDE TRIM"
in EXTERIOR & INTERIOR (EI) section.
2. Disconnect the rear combination lamp connector.
3. Remove the rear combination lamp mounting bolts.
4. Pull the rear combination lamp toward rear of the vehicle and
remove from the vehicle.
5. Remove the harness from the vehicle.
SKIA0801E
INSTALLATION
Install in the reverse order of removal, taking care of the following points.
Rear combination lamp mounting bolt
: 4.5 - 6.4N-m (0.45 - 0.65kg-m, 39 - 59 in-lb)
LT-32
INTERIOR ROOM LAMP
LT
TKWH0020E
LT-33
INTERIOR ROOM LAMP
TKWH0109E
LT-34
INTERIOR ROOM LAMP
LT
TKWH0026E
LT-35
INTERIOR ROOM LAMP
TKWH0110E
LT-36
INTERIOR ROOM LAMP
LT
TKWH0111E
LT-37
INTERIOR ROOM LAMP
TKWH0112E
LT-38
INTERIOR ROOM LAMP
LT
TKWH0113E
LT-39
INTERIOR ROOM LAMP
SKIA0419E
SKIA0064E
SKIA0419E
2. Remove the interior room lamp mounting bolts and remove the interior room lamp.
3. Disconnect the interior room lamp connector.
LT-40
INTERIOR ROOM LAMP
SPOT LAMP
1. Using a clips driver or a suitable tool, press and remove the A
metal clip of the spot lamp.
2. Disconnect the spot lamp connector.
B
SKIA0064E D
LT
LT-41
LUGGAGE ROOM LAMP
TKWH0114E
LT-42
LUGGAGE ROOM LAMP
A
1. Insert a thin screw driver push the pawl and remove the lens.
2. Remove the bulb.
Luggage room lamp :12V 5W B
D
SKIA0428E
1. Insert a thin screw driver push the pawl and remove the lens. E
2. Remove the luggage room lamp mounting screw and remove the luggage room lamp.
3. Disconnect the luggage room lamp connector.
F
LT
LT-43
ILLUMINATION
ILLUMINATION PFP:00011
LT-44
ILLUMINATION
LT
TKWH0107E
LT-45
ILLUMINATION
TKWH0108E
LT-46
ASHTRAY ILLUMINATION
SKIA0492E
LT
LT-47
BULB SPECIFICATIONS
Headlamp EKS003QR
LT-48