Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Whereas the Parliament of India has set out to provide a practical regime of right to
information for citizens to secure access to information under the control of public authorities,
in order to promote transparency and accountability in the working of every public authority,
and whereas the attached publication of the Bureau of Indian Standards is of particular interest
to the public, particularly disadvantaged communities and those engaged in the pursuit of
education and knowledge, the attached public safety standard is made available to promote the
timely dissemination of this information in an accurate manner to the public.
1 +, 1 + 01 ' 5
Mazdoor Kisan Shakti Sangathan Jawaharlal Nehru
The Right to Information, The Right to Live Step Out From the Old to the New
! $ ' +-
Satyanarayan Gangaram Pitroda
Invent a New India Using Knowledge
! > 0 B
BharthariNtiatakam
Knowledge is such a treasure which cannot be stolen
IS : 11668 - 1985
UDC 74443 : 621 - 229335 : 003.62 IS0 6411 - 1982
( Reaffirmed 2005 )
Indian Standard
Is1
1
._C.. ..p_
I
I
TECHNICAL DRAWINGS - SIMPLIFIED
REPRESENTATION OF CENTRE HOLES
National Foreword
This Indian Standard is identical with IS0 641 I-1982 Technical drawings - Srmplified
epresentation of centre holes issued by the International Organization for Standardization ( IS0 I, was
adopted by the Indian Standards Institution on the recommendation of the Drawings Sectional
Committee and approvafof the Mechanical Engineering Division Council.
In the adopted standard certain terminology and conventions are not identical with those used
II? Indian Standard; attention is especially drawn to the following:
Wherever the words International Standard appear, referring to this standard, they should be
read as Indian Standard .
The reference of ISO 6,411 indicated in designation should be read as IS : 11668 - IS0 6411.
Cross References
1 Scope and field of application IS0 309811, Technical drawings - Lettering - Part 1 :
Current& used characters.
This International Standard specifies the simplified represen-
tation of centre holes and their designation. Simplified IS0 6428, Technical drawings - Requirements for micro-
representation of centre holes may be used particularly when it copying. 1)
is not necessary to show the exact form and size and where the
designation of standardized centre holes is sufficient for infor-
mation.
3 Indication on drawings
2 References
3.1 Requirements
IS0 128, Technical drawings - ~General principles of presen-
tation. Generally, three different requirements may be defined on
technical drawings for the form and size of centre holes,
IS0 866, Centre drills for centre holes without protecting namely :
chamfers - Type A.
a) centre hole is required on the finished part;
IS0 2540, Centre drills for centre holes with protecting
chamfers - Type 6. b) centre hole can be accepted on the finished part, but is
not a fundamental requirement;
IS0 2541, Centre drik for centre holes with radius form -
Type R. c) centre hole shall not exist on the finished part.
a
IS :11668-1985
IS0 6411 -1982
The symbols representing centre holes and their application to The two values are separated by a solidus.
the end face of a shaft are shown in column 2 of table 1.
Example : a centre holet), type B with d = 2.5 mm and
D3 = 8 mm may be indicated on the drawing as :
3.3 Designation of centre holes
IS0 8411-B 2,5/8
The designation of centre~holes is dependent on the drill and
may be indicated with refarence either to an International Stan-
dard or to any other standard dealing with this subject. 4 Interpretation of vindication
The desrgnation of the centre hole itself consists of The relationship between the various designations used to
specify the centre holes, the dimensions represented by the
- a reference to this International Standard; given designations, and dimensions depending on the centre
drill used are shown in table 2.
- the letter for the type (I% A or 6);
Further details specifying the dimensions of the centre hole, to
- the prlot arameter d; be indicated preferably on the drawings, are given in annex A
II For the machining of such a centre hole, a drill with d = 2,5 and d, = 10 according to IS0 2540 is used.
3
IS :I1668 -1985
IS0 6411 - 1982
I
Type of
D_esignation (examples) Interpretation of the designation
centre hole
R
with radius form
i _
without
A
chamfer
protecting
_~. 6411-A 418.5
t*
L-4
centre drill according
IS0 866)
tl
d=4
L I**
D2= 8.5
with protecting
6
chamft
_~. 6411- 82,5/8
c/=2,5
4=8
l
For dimension I, see annex A
l * Dimension I depends on the length of the centre drill. It should not he less than i
4
IS : 11668 - 1985
IS0 6411 - 1982
Annex A
The dimensions which are necessary to specify a centre hole are shown in table 3
Tvw
R - A B
d according to IS0 2641 according to IS0 866 accordtnq to IS0 2540
nom. DI 4 I r* i
nom. nom. ref 0) ref
I
10,5) 1.06 0.5
(0,631 1.32 06
(0.8) 1.70 t 0.7
1.0 2.12 2.12 0.9 3 15 0.9
(1.25) 2.65 2~65 l,l 4 1.1
1.6 3.35 3.35 1.4 5 14
2,o 4.25 4,25 1.8 6.3 1.8
2.5 5.3 5.30 2.2 8 2.2
3.15 6.7 6,70 2.8 10 2.8
4.0 8.5 8.50 3.5 12.5 35
(5 0) 10.6 10.60 4.4 16
6.3 13.2 13.20 55 18
(8.01 17.0 17,00 7.0 224
28
10.0 21.2 21.20
1 a.7
Annex B
In order to harmonize the sizes of the symbols specified in thiq B.2 Proportions
International Standard with those of the other inscriptions on
the drawing (dimensions, tolerances, etc.) the following rules The symhol and its complements shown in area a (see 8.3)
shall he ohserved. shall he drawn in accordance with the figure.
B.l.1 The symbols shown in the table shall he inscribed with The range of sizes to he used for the symbols and additional
a line thickness (d ) equal to 1 /lO of the height (h) of the letter- indications is given in tahle 4.
ing used for the dimensions in the relevant drawing.
Table 4 - Dimensions, in millimetres
B.1.2 The numerals and capital letters used for the additional
Line thickness for
specifications of centre holes shall be inscribed with the same outlines of an item Ih) 0.5 0.7 1 1.4 2 2.8
line thickness (~1, height (h) and type of lettering as us&d for
the dimensions in the relevant drawing, and in accordance with Height of_numerals
and capital letters (h) 3.5 5 7 10 14 20
IS0 309811. -
Line thickness for
symbols (d ) 0.35 0.5 0.7 1 1.4 2
B.1.3 The minimum spacing hetween adjacent lines shall be ______~_
Line thickness for
in accordance with IS0 128 or IS0 6428. see 8.1.2
lettering (d)
Height H1 5 7 10 14 20 28
It is recommended that this spacing he not less than 0.7 mm.
Figure