Documentos de Académico
Documentos de Profesional
Documentos de Cultura
1
Structural Catalogues
www.aveva.com
Australia/New Zealand
Canada
Chile
China
Europe
India
Japan
Russia
South Africa
UK
USA
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Gtypes
The following table shows the Gtypes:
Gtype
Description
PFI
Parallel Flange I
PFC
PFT
TFI
Tapered Flange I
TFC
TFT
TWT
TFWT
ANGL
RTUB
CTUB
Circular Tube
ZED
Z Profile
CEE
Flanged C Profile
BFLA
Bulb Flat
PLTG
Plate Girder
BOXG
Box Girder
FBAR
Flat Bar
RBAR
Round Bar
HBAR
Hex Bar
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Parameters
The following table shows the parameters:
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
`15
16
17
18
19
20
21
22
23
Parameter Description
Depth
Width A
Width B
Width C
Web Thickness
Flange Thickness A
Flange Thickness B
Radius A
Radius B
Radius C
CofG X Axis Offset
CofG Y Axis Offset
Flange Thickness Centre Offset
Flange Slope (degrees)
Web Slope (degrees)
Gage Line A
Gage Line B
Gage Line C
Maximum Bolt Diameter A
Maximum Bolt Diameter B
Mass per Unit Length
Surface Area per metre
Cross Sectional Area
Dkey
DPTH
WIDA
WIDB
WIDC
WTHK
FTKA
FTKB
RADA
RAD B
RAD C
CGXO
CGYO
FTCO
FSLO
WSLO
GLNA
GLNB
GLNC
MBDA
MBDB
MAUL
SAPM
XSAR
Data Type
Geometry
Geometry
Geometry
Geometry
Geometry
Geometry
Geometry
Geometry
Geometry
Geometry
Geometry
Geometry
Geometry
Geometry
Geometry
Data
Data
Data
Data
Data
Data
Data
Data
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Gtype PFI
Gtype PFC
Gtype ANGL
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Plines (1)
All Gtypes will have common set of 14 standard
Plines.
9 Plines will be at corners, mid-points and centre of
a bounding box around the profile
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Plines (2)
1 Pline is at the Neutral Axis (NA) and 4 Plines are
positioned where lines drawn through the NA in the
X and Y directions cross the bounding box.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Plines (3)
Symmetrical profiles will have some coincident
Plines. Asymmetrical profiles will have no coincident Plines.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Plines (4)
Gtype specific Plines are added, as highlighted in
red, where required to facilitate trimming of
attached members in all cases.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Plines (5)
The Cconnect attribute of Standard Plines and
Gtype Specific Plines, as highlighted in red, are set
to ANY, as required.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Display Levels
0-3
4-8
9 - 10
Obstruction Value
0
2
1
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Description
DPFI
DPFC
DPFT
DANG
DRTU
DCTU
DZED
DCEE
DPLG
DBXG
DFBA
DRBA
DHBA
DCON
DTWI
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
Baseplate fittings
Stiffener fittings
Lifting Lug fittings
Padeye fittings
Shear Stud fittings
Scaffold Clip fittings
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.
www.aveva.com
Copyright 2015 AVEVA Solutions Limited and its subsidiaries. All rights reserved.