Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Resumen
La práctica llevada a cabo se basa en la utilización del método de Kynch para la determinación
del área unitaria de sedimentación en un mineral. Se partió de una muestra de unos 200 g que fue
previamente molida y clasificada mediante un ensayo de tamizado, para después realizar una prueba
donde con el mineral mezclado con la pulpa con y sin floculante se le toman mediciones de volumen
cada cierto intervalos de tiempo. Después de realizada la prueba se procede a analizar aspectos como
las zonas del esquema de Kynch, valores de área obtenidos y la zona de clarificación con y sin
floculante. La prueba de determinación del área de sedimentación por el método de Kynch fue
realizada en la escuela de Ciencia e Ingeniería de Materiales del Instituto Tecnológico de Costa Rica.
Palabras clave
Abstract
The practice carried out is based on the use of Kynch method for determining the sedimentation unit
area in a mineral. It began with a sample of about 200 g which was previously ground and classified
by a sieve test, then a test where the mineral mixed with the pulp was made without and with
flocculent and some volume measurements are taken at some time intervals. After performing the test
the analysis of aspects in the scheme areas Kynch values are obtained and the clarification zone with
and without is .determined . The test for determining the area of sedimentation by the method of
Kynch was performed in the School of Materials Science and Engineering of Costa Rica Institute of
Technology.
Key word
Página 1
INSTITUTO TECNOLÓGICO DE COSTA RICA
ESCUELA DE INGENIERIA EN MATERIALES
Carrera: Ingeniería en Materiales
1. OBJETIVOS
Página 2
INSTITUTO TECNOLÓGICO DE COSTA RICA
ESCUELA DE INGENIERIA EN MATERIALES
Carrera: Ingeniería en Materiales
𝑡𝑢 3. MATERIALES Y MÉTODOS
𝐴𝑟𝑒𝑎 𝑢𝑛𝑖𝑡𝑎𝑟𝑖𝑎 =
𝐶𝑜 𝐻𝑜
En la práctica realizada de sedimentación los
materiales utilizados son los siguientes:
Página 3
INSTITUTO TECNOLÓGICO DE COSTA RICA
ESCUELA DE INGENIERIA EN MATERIALES
Carrera: Ingeniería en Materiales
Página 5
INSTITUTO TECNOLÓGICO DE COSTA RICA
ESCUELA DE INGENIERIA EN MATERIALES
Carrera: Ingeniería en Materiales
7. ANEXOS
Resultados:
Sin Floculante 104 g.
Volumen Inical = 1000 mL pulpa.
Concentración = 36 cm / L
Altura Inicial = 30 cm
Página 6
INSTITUTO TECNOLÓGICO DE COSTA RICA
ESCUELA DE INGENIERIA EN MATERIALES
Carrera: Ingeniería en Materiales
20
15
10
5
0
0 100 200 300 400 500
Tiempo (s)
(7⁄1440)
𝐴𝑢 = = 4.50𝑥10−6 𝑐𝑚2
(30)(36)
Página 7
INSTITUTO TECNOLÓGICO DE COSTA RICA
ESCUELA DE INGENIERIA EN MATERIALES
Carrera: Ingeniería en Materiales
Tabla 2. Volúmenes Registrados a Diferentes Tiempos durante el Proceso de Sedimentación con Floculante.
Tiempo Altura
(s) (cm)
0 36 30
2 33.5 27.92
4 31.4 26.17
6 29.5 24.59
8 27.3 22.75
10 26 21.67
12 25 20.83
14 24.3 20.25
16 23.3 19.42
18 22.4 18.67
20 22 18.33
22 20.9 17.42
24 19.5 16.25
26 15.2 12.67
28 13.6 11.33
30 12 10.00
32 10 8.33
34 8 6.67
36 6.5 5.42
38 5.2 4.33
40 4.2 3.50
42 3.2 2.67
300 2.9 2.42
Página 8
INSTITUTO TECNOLÓGICO DE COSTA RICA
ESCUELA DE INGENIERIA EN MATERIALES
Carrera: Ingeniería en Materiales
20
15
Series1
10
5
0
0 100 200 300 400
Tiempo (s)
Tangente𝑡𝑐𝑟í𝑡𝑖𝑐𝑜 = 3.8 𝑠
(5⁄1440)
𝐴𝑢 = = 3.22𝑥10−6 𝑐𝑚2
(30)(36)
Página 9
INSTITUTO TECNOLÓGICO DE COSTA RICA
ESCUELA DE INGENIERIA EN MATERIALES
Carrera: Ingeniería en Materiales
Página 10