12-TUNE MUSICAL DOOR-BELL
T: suid lee tli pues st =
ent musical tine every time some- :
oncyriige up thedaci “ball What x. Ya
warm welcome! The unit works on just two pe
pencil (AA) size celle and yet gives ample | aoa
sound output. The circuit diagram of the
12-tune door-bell is shown in Fig. 1
Apart from being a door-bell, it is also | SS,
useful as.a telephone interlude music player,
toy or attention call-bell as mentioned
earlier
feurno
‘This simple-to-ussemble, really low-cose
and versatile 12-tune doorbell can be as~
sembled within 15 minutes and would cost
Jess—much cheaper than readymade ones
available in the market =
The heart of the circuit is an IC, fig s:Cieultdiagramara ample 1tune nical door bell
popularly known as Musical Door-bell IC’,
Such ICsare available with several diffrent
type numbers as UM3481/82/83 or CIC481/82/83
and CIC 4822/33 etc, but they can easily replace each
other,as all are 16-pin DIP ICs and equivalents. Use
any one. Please note, UM3481 contains eight Christ
mas carols while 3482 contains 12 tunes—most suit~
Somiconcectore
Ich + UM3481/82/853 pre pmgeammed ROM.
in Paithees eee
pi + IN4OOH, Tramp ctf diede
Resigars (ll neat, +5% carbon):
RI * 100-Kilehm
m2 = 15-kilobes
able for a door-bell or other applications.
Each of these ICs contains a ROM with $12 mu-
sical notes, tone generator, rhythm generator, timbre
genentor, moduktor, ‘run-of? control, oscillators,
frequency divider and preamplifiers. So a very few
number of components have to be connected exter
nally to set up the timing of built-in oscillator and to
build up an extemal AF amplifier/driver circuit.
‘Transistor T1 (SL100) is used as an amplifier
driver connected to on-chip preamplifier output (pin
11) to driveany 8-ohm or 4-ohm loudspeaker directly
Resistor R1 controls tempo, ic. the speed at
which the tune is played. Tempo can be varied as per
choice by changing the value of R1 within 82 to 150 kilohms.
lc ~ 33pF ceramic disc
lc + 0.048 ceramic disc
Ls Bee eee
st + Pask-to-on switch
+ I6pin IC socket, PCR, hnttery holder, enclose,
Bebe wite ot.
Testing procedure
‘After completing the wiring of the circuit, check the placement of IC on the PCB. Connect milliammeter
capable of reading up to 10 mA in series with positive supply line and switch on the circuit, ensuring that the
current consumption is 5 mA to & mA. If itis more than 8 mA, it indicates that something is wrong either inSanta Claus Is Comming to Town
Silent Might, Holy Night
Joy to the Woeld
[Sard rn in |
ee ee |
ee |
Hacks Hemi Angle Smgh ed |
Ameen 1 2
itn
Ob My Daring Clementine wee ru.
See
Lae page Fleg Dove ie
peers
et "en sta door em tad
Happy Birtatay | oN sare
feaee 10 arin Wi randiate. So Fret gt
(Hoos Bastion Ce ier Pckereta ion T
Wiegeniied of transistor T1 (SL100) and
Mele on Purple Basnboo then of the IC Fig 3:-Components layoutfor the PCB
Leaves a) ‘After eoufieniing that tie
es emma eee pee tt cee
Comin? Tae the ye! (pitch) of the playing music, [Fit is too fast then slow it down to
Wedding March
Happy Birtstay
ees
laces decreasing the value of C1 (33pF) to 10pF or 22pF.
(cnet menees Eseeae
ers oes eee ,
Warmer! Chie Fencion | Construction
an acceptable limit by increasing the value of capacitor C1 to 47pF
0 68 pF by trial and erzor. [fit is too slow, increase the speed by
‘The entire circuit can be assembled on the suggested PCB layout
(Fig 2) and enclosed in a pocket transistor cabinet, with speaker and battery holder. Switch $1 is to be fitted
outside the main door as 2 bell push. IC should be soldered directly on to the PCB using a 10-watt soldering
ion. Do not heat the pins for more than 10 seconds while soldering. as the IC may get damaged. Alternatively,
you can use an IC socket
‘The type of speaker used is not critical. But for a loud sound output, use a speaker with at least Sem diameter.
IF required,a 3V or 4V DC mains adaptor can also- be used to power the bell
Note: UM3481 is available with EFY's associate concem,M/s Kits ‘a’ Spares, D85/5, Okhla Industrial Area,
Phase-1,New Delhi-110020,