Documentos de Académico
Documentos de Profesional
Documentos de Cultura
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
1
1/13/2016
Specifier's comments:
1 Input data
Anchor type and diameter:
Material:
8.8
ETA-13/1036
Issued I Valid:
12/15/2014 | 12/15/2019
Proof:
Stand-off installation:
eb = 0 mm (no stand-off); t = 4 mm
Anchor plate:
Profile:
no profile
Base material:
Brick layout: Double Stretcher; Brick: Solid Vbn, 2DF, f=6 (solid brick), Normal weight concrete, L x W x H:
240 mm x 115 mm x 113 mm;
fb,v = 6.00 N/mm2; Ewall = 1577.31 N/mm2
Mortar: M2,5 - M9; Vertical joints filled: YES; vertical: 5 mm; horizontal: 5 mm
Plaster
Installation/Use:
Geometry [mm]
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
1/13/2016
Shear force x
0.070
Shear force y
-0.690
Tension
x1
Capacity [kN]
19.333
Utilization bN [%]
1
Status
OK
Pullout Strength*
0.190
0.750
26
OK
Brick breakout**
0.190
0.750
26
OK
0.190
55.428
OK
Steel Strength*
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
gM,s
1.500
NRd,s [kN]
19.333
NSd [kN]
0.190
aj
0.750
gM,m
2.500
NRd,p [kN]
0.750
NSd [kN]
0.190
s|| [mm]
0
s^ [mm]
0
scr,|| [mm]
240
scr,^ [mm]
113
c [mm]
400
ccr [mm]
115
NRk,b [kN]
2.500
aj
0.750
ag,N
1.000
gM,m
2.500
NRd,b [kN]
0.750
NSd [kN]
0.190
AHact [mm2]
55200
AVact [mm2]
25990
fvko [N/mm2]
0.15
2
sd [N/mm ]
6.00
NRk,pb [kN]
138.569
gM,m
2.500
NRd,pb [kN]
55.428
NSd [kN]
0.190
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
1/13/2016
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
1/13/2016
Capacity [kN]
N/A
Utilization bV [%]
N/A
Status
N/A
0.694
1.132
62
OK
0.694
1.200
58
OK
0.694
17.300
OK
0.070
109.296
OK
aM
1.00
NSd / NRd,s
0.010
1 - NSd / NRd,s
0.990
M0Rk [kNm]
0.030
VM
Rk,s = aM * MRk,s / l [kN]
1.415
gMs,b,V
1.250
VM
Rd,s [kN]
1.132
VSd [kN]
0.694
s^ [mm]
0
scr,|| [mm]
240
scr,^ [mm]
113
c [mm]
400
ccr [mm]
115
ag,V
1.000
aj
0.750
VRk,b [kN]
4.000
gM,m
2.500
VRd,b [kN]
1.200
VSd [kN]
0.694
dnom [mm]
8
hef [mm]
145
fb,v [N/mm2]
6.00
c1 [mm]
400
VRk,c [kN]
43.249
ag,V
1.000
gM,m
2.500
VRd,c [kN]
17.300
VSd [kN]
0.694
fvko [N/mm2]
0.15
2
sd [N/mm ]
6.00
VRk,pb [kN]
273.240
gM,m
2.500
VRd,pb [kN]
109.296
VSd [kN]
0.070
5 Combined tension and shear loads (ETAG 029 Annex C, Section C.5.2.3)
bN
0.253
bV
0.613
a
1.000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Status
OK
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
5
1/13/2016
6 Warnings
Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the loading!
Input data and results must be checked for agreement with the
existing conditions and for plausibility!
Only the local load transfer from the anchor(s) to the wall is considered, a further load transfer in the wall is not covered by PROFIS!
Wall is assumed as being perfectly aligned vertically checking required(!): Noncompliance can lead to significantly different distribution of
forces and higher tension loads than those calculated by PROFIS. Masonry wall must not have any damages (neither visible nor not visible)!
While installation, the positioning of the anchors needs to be maintained as in the design phase i.e. either relative to the brick or relative to the
mortar joints.
The effect of the joints on the compressive stress distribution on the plate / bricks was not taken into consideration.
If no significant resistance is felt over the entire depth of the hole when drilling (e.g. in unfilled butt joints), the anchor should not be set at this
position or the area should be assessed and reinforced. Hilti recommends the anchoring in masonry always with sieve sleeve. Anchors can only
be installed without sieve sleeves in solid bricks when it is guaranteed that it has not any hole or void.
The accessories and installation remarks listed on this report are for the information of the user only. In any case, the instructions for use
provided with the product have to be followed to ensure a proper installation.
The compliance with current standards (e.g. ETAG 029) is the responsibility of the user.
The Youngs modulus of the wall Ewall (not plastered!) is determined in accordance to EN 1996-1-1:2012
Drilling method (hammer, rotary) to be in accordance with the approval!
Masonry needs to be built in a regular way in accordance with state-of the art guidelines!
Please note that, for ETA approved masonry units, the resistance and parameters are only valid for that particular brick (hollow/solid) or for bricks
of the same base material with larger size and larger compressive strength (solid), according to ETAG 029.
A default value of Eplaster = 1000.00 was assumed.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
6
1/13/2016
7 Installation data
Anchor plate, steel: Profile: no profile; 0 x 0 x 0 mm
Hole diameter in the fixture: df = 17 mm
Plate thickness (input): 4 mm
Recommended plate thickness: not calculated
Cleaning: compressed air
20
20
20
20
20
20
Coordinates Anchor mm
Anchor
1
x
0
y
0
c-x
500
c+x
400
c-y
1000
c+y
1000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
20
20
www.hilti.co.uk
Company:
Specifier:
Address:
Phone I Fax:
E-Mail:
Page:
Project:
Sub-Project I Pos. No.:
Date:
7
1/13/2016
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan