Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Table of Contents
File Downloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
File Downloads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Advertisements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Author:koogar runawaybrainz
Rupert Hirst "If I can't beg,buy,borrow or find something then I guess I will just have to make it!"
This headphone amplifier circuit is different to conventional modern construction techniques in that it is air Wired,P2P (peer to peer) or free form wiring just like in the
good old Valve days before the intervention of PCB's and the transistor.
Rather than a traditional enclosure, the hole circuit is encapsulated in polyester resin to enhance the internals.
If your reading this and thinking why do you need an amplifier for headphones then click here
Although allot of cMoy headphone amplifiers are designed to be portable this one is designed for the desktop although a battery pack could be made also.
This is a pretty long instructable so "make a brew" as we say in Yorkshire and get comfy .
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 1: The Schematic
Here is the EaglePCB schematic of headphone amplifier it follows the cMoy design
1x DC Power Jack
1x 5mm LED
R1LED : 1x 1k to 10k 0.6 watt metal film resistor (For the Power LED, Anywhere from 1k to 10k will be good it all depends on the input voltage and how bright you like
your LED.)
CP1/2 : 2x 470uf 35 or 50v Power Capacitors
RP1/2 : 2x 4.7k 0.6 watt metal film resistors (For the power supply Voltage divider)
Amplifier section
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
File Downloads
Everything has to be visually spot on because everything will be on show for all time when its cast in resin.
To create the power bus I used solid core 1.10mm wire taken from mains twin and earth cable used for the internal house wiring.
Soldering Iron
Solder (preferably thin gauge)
Flux Pen (optional)
Long nose pliers for bending
Snips
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 3: External Power Supply
For the main external power supply you will need a switch mode type, I used one from an old router anything in the voltage range of 9-18VDC and current rating 300ma
upward will do.
You will also need a power supply with a positive center pin this is denoted by the symbol with in the red circle on the picture.
If you detected any hum in you headphones when you test the circuit before the resin pour check all the circuit then try using a different model of power supply.
If the power supply you selected is a cheap wall-wart that contains a transformer (linear power supply) it will no doubt hum though the headphones
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 6: Making the Skeleton 2
Here we can see the basic layout of the power supply section
It is a double-ended power supply that takes a single-ended input (12VDC) and splits it with a voltage divider.
The hoops on the right are for the op-amp circuit this requires +/GND/- instead of just +/GND.
What this basically means is the power input for the Burr Brown OPA2107 Operational amplifier or Op-Amp needs -Volts and +Volts the T shaped wire which runs down
the middle is the ground or in this case a "virtual ground" produced by the voltage divider it never comes into direct contact with the main power ground incoming from the
power jack.
The two 4.7k resistors near the back are the voltage dividers,the supply to the power jack in this case is 12VDC is then halved by the voltage divider producing -6v and
+6v on both of the outer copper wires or you could call then buses.
The +V for the LED is fed straight out of the back of the power jack and uses the -6v copper wire for Ground through a 1k Resistor ,as this all comes before the voltage
divider as far as the LED is concerned -6v is normal ground.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 7: Making the Skeleton 3
The two large silver 470uf 50v capacitors are for the power supply rails followed by the two red bi-pass capacitors for Op-Amp stability just in case of any oscillation which
strictly speaking should be attach as close to the Op-Amp legs as possible .Having said that i haven't had any stability issues with this IC in other Cmoys i have made.
In the 3rd picture the bottom 4 Leads can now be connected to the virtual ground (middle copper wire)
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 9: Making the Skeleton 4
Time to add the Input caps these stop any DC voltage (Direct Current) entering the amplifier from the source (iPod ETC) through the input jack socket as this would also
be amplified by a factor of the gain. Audio signals work on AC (Alternating Current).The gain is set quite lower as the input source in this case the PC has high output and
there will be no volume potentiometer to physically adjust volume.
In the second picture the legs from the turquoise resistors are bent to form the output connection which will be hooked up to the headphone jack socket.
The 3rd & 4th picture shows hooking up the audio Input and headphone jacks.
I used enamelled wire from an old transformer to give a consistent look but it also has a good amount of insulation against shorts.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 10: Making the Skeleton Reference Pictures
Here are a few additional photos for reference.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 11: Testing
At this stage DO NOT test the amplifier with your best headphones use some cheap old headphones
Both of the audio Jack Socket sides were removed during the sealing process, the sides were then replaced after applying resin all around the edges.
Resin was also placed around all the connections pins around the bottom to ensure an airtight seal.
More resin was used around the bottom of the DC jack.I am hoping the extra resin will not show much in the finished casting.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 13: Pre Casting Sealing 2
Using Blue Tack and clear tape the three sockets were plugged, fingers crossed ;)
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 15: Label the Audio Sockets
I thought it might be nice to make a couple of Input Labels ,partially to improve the appearance of the sockets.
After measuring the sockets they were made to and printed to scale in Adobe PhotoShop then printed on thin photo paper then using double sided tape stuck to the
socket sides.
I realise that there are better ways to create a mould like using silicone but the aim is to get the sides as square and true as possible as this is a one off project card
seemed ideal.
Next I designed the mould templates in EaglePCB then using double sided tape stuck the print out on to the card to be cut.
When it came time for assembly of the mould each corner was tacked in place with super glue till all parts of the mould were together as one at which point I ran more
super glue around the entire length of each side.After this had completely dried a second run of glue was applied to ensure the joints were completely sealed.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
File Downloads
I could have measured the mould with a ruler but this was quicker and gave me an indication of approximate weight of resin needed to fill the volume of the mould, you
also have to factor in the displacement of the item being encapsulated.
I estimated water would roughly be a similar density and weight to the resin.
Now you know the volume you need to follow the instructions for the resin you have purchased to find the correct ratio of resin to hardener.
I used Polycraft DSM Synolite Water Clear Casting Resin + MEKP Catalyst (1 to 2%), I believe it is a polyester resin the ratio of Catalyst to Resin was around 1%.
It was pretty hard to measure out the catalyst in such small amounts.
There are many varieties, which all require different ratios of resin to hardener.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 18: Mixing the Resin
With the resin mixed I had to ensure I poured it slowly and close to the mould so not to encourage air bubbles.
You can see in the below picture that's there is a dome of resin rising above the mould, this is to allow for shrinkage as the resin cures.
Once the resin is mixed you will not have long to work with it before the curing starts so have everything you need to hand.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 19: Curing the Chemical Reaction
The mould was then covered to stop any debris or dust entering the cast.
A chemical reaction will start and the cast will generate allot of heat this is the curing process at work
At this point the surface starts to gel, it shows as dimpling of the surface.
I left the cast for 24hours to fully harden before starting the next stage.
I used Belt sander was squarely clamped well in a vice (please be careful when doing this!)
After some wet sanding with P600 then P1200 Grit paper I was left with the basic shape.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 21: Knocking the Edges off
Using the Vice again I clamped my router with a makeshift platform on top.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 22: Final Polish
To polish the surface again I used P600 then P1200 grit wet and dry paper dipped in water.
I found that T-CUT or Brasso made an excellent buffing polish it literally shined the surface up from a dull finish.
The precautions when sealing the sockets worked rather well and no resin entered the Jack socket cavities,there are a couple of tiny air bubbles but nothing that can
really be seen.
The only way to totally eliminate air bubbles would have been to use a vacuum chamber or dome since .Having thought about this I think it may well have forced resin
into the air cavities.
One tip if you had a vacuum chamber or dome would be to just vacuum the resin after mixing before the pour as the mixing process introduces some small air bubbles.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 23: Precautions
There maybe some concerns regarding the capacitors in the event of polarity reversal.
If your using a manufactured power supply such as a wall wart or power brick and the jack has a positive centre this is not really an issue.
In the event of catastrophic failure capacitors are built with a fail safe to release pressure. On the end of the capacitor the cap is scored thus weakening it. This in turn
stops the capacitor building too much pressure .
As a safety precaution pilot holes could be drilled as near to the capacitor ends (not into!) as possible.This would act as a weak link or escape valve for any build up of
pressure
Although the circuit will no longer be serviceable once cast it will give me an incite in to what may have gone wrong by checking the the virtual ground (the
wire stands) against the negative and positive power jack connections.
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Step 25: Running Temperature
HOT OR NOT !
Here are the results at 12vdc (-6/+6) playing music at above normal levels for 60 minutes
I already knew the circuit would not produce any significant heat before I began .If this was a concern I would have embedded a small heat sink on the top of the IC
revealing itself on the top surface of the casting.
Although there is no metal shielding as you would have in a conventional chassis/PCB the amplifier exhibits no unwanted noise or RF interference as you may associate
with an open chassis design such as this it is dead silent even though it is next to my mobile phone and WiFi router.
Electronic engineers have been encapsulating or potting electronics in resin's for decades usually for vibration dampening or moisture control its just I decided to make it
look presentable :)
Rupert
runawaybrainz.blogspot
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/
Related Instructables
Advertisements
http://www.instructables.com/id/Crystal-cMoy-Free-Form-Headphone-Amplifier/