Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Martina Soderlund
University of Washington
2007
University of Washington
Abstract
Sustainable Roadway Design
A Model For An Environmental Rating System
Martina Soderlund
Chair of the Supervisory Committee:
Assistant Professor Stephen T. Muench
Civil and Environmental Engineering
The building construction industry in the U.S. has in the last 5-10 years gone through a market
transformation towards construction and design of more sustainable buildings. One reason to this
transformation is the implementation of the LEEDTM (Leadership for Energy and Environmental
Design) green building environmental rating system.
The construction of roads is one of the most material demanding industries in the world with
great economic as well as environmental impacts. Significant efforts are seen in terms of
recycling and reuse of pavement materials. These efforts are strong and are beginning to be part
of industry processes and practice, however, this is not sufficient to create sustainable products
over entire life cycles.
If a similar rating system such as LEEDTM could gain popularity for projects in the roadway
construction industry as it has in the building industry, significant benefits in environmental
awareness and sustainability in design can be achieved. Today no such rating system exists for
roads.
This study has developed a model for such a system for use in Washington State. Elements and
impacts of sustainable attributes in roadway design has been identified and researched. Categories
of environmental significance have been developed and suggestions of requirements for the
design team are being proposed together with comments of implementation strategy. This model
can serve as a base for further research and development of an environmental rating system for
roadway design.
TABLE OF CONTENTS
List of Figures .................................................................................................................................. v
List of Tables ..................................................................................................................................vi
1. Introduction ............................................................................................................................... 1
2. Research Objective.................................................................................................................... 2
2.1
3. Methodology ............................................................................................................................. 3
3.1
3.2
3.3
Literature review.................................................................................................... 3
Classification of design categories......................................................................... 3
Development of a rating system ............................................................................ 3
4. Background ............................................................................................................................... 4
4.1
8.4
8.5
8.6
8.7
8.8
Overview.............................................................................................................. 11
8.1.1 Terminology ........................................................................................12
Waste, Recycling & Road Construction .............................................................. 13
8.2.1 Construction Waste and Recycling......................................................14
8.2.2 Construction Debris in Washington State ...........................................16
Design Options .................................................................................................... 17
8.3.1 Reclaimed Asphalt Pavements ............................................................19
8.3.2 Recycled Concrete Pavements.............................................................20
8.3.3 Steel .....................................................................................................21
8.3.4 Blast Furnace slag, Slag cement ..........................................................21
8.3.5 Fly-Ash ................................................................................................22
8.3.6 Glass ....................................................................................................24
8.3.7 Scrap Tires...........................................................................................24
8.3.8 Shingles ...............................................................................................25
8.3.9 Foundry sand .......................................................................................26
Pollution Prevention Opportunities ..................................................................... 26
Cost ...................................................................................................................... 28
Life Cycle Analysis Environmental Focus ....................................................... 29
8.6.1 LCA Tools for Pavement Design ........................................................30
Transportation Activities ..................................................................................... 30
Regulations in Washington State ......................................................................... 31
i
8.9
9.4
9.5
9.6
Overview.............................................................................................................. 43
Stormwater and Roadways .................................................................................. 45
9.2.1 Best Management Practices, BMPs ...................................................46
BMP Options ....................................................................................................... 47
9.3.1 BMPs for Stormwater Source Control.................................................47
9.3.2 BMPs for Stormwater Runoff Treatment ............................................47
9.3.3 BMPs for Stormwater Flow Control ...................................................48
9.3.4 Emerging Techniques..........................................................................49
9.3.5 Low Impact Development Design (LID).............................................50
9.3.6 Manufactured Devices Subsurface Treatments ................................52
9.3.7 Partial Exfiltration Trench (PET) ........................................................54
9.3.8 Permeable Pavements ..........................................................................54
9.3.9 Alternative Road Layout for Residential Areas...................................58
Pollution Prevention Opportunities ..................................................................... 59
Regulations in Washington State ......................................................................... 63
Criteria Definitions .............................................................................................. 65
9.6.1 SM-1. Storm Water Management........................................................66
9.6.2 SM-2. Storm Water Design 1 - Runoff Treatment ..............................68
9.6.3 SM-3. Storm Water Design 2 Permeable Area.................................69
9.6.4 SM-4. Storm Water Design 3 Permeable Pavement.........................71
9.6.5 SM-5. Innovative Stormwater Technology .........................................72
iv
LIST OF FIGURES
Figure Number
Page
LIST OF TABLES
Table Number
Page
vi
ACKNOWLEDGEMENTS
I would like to give special thanks to Professor Stephen T. Muench for outstanding support and
enthusiastic guidance throughout my work as well as to fellow committee members Joe P.
Mahoney and G. Scott Rutherford for their commitment and support. I deeply appreciate the
corporate professionals that took time to meet with me for interviews and helpful discussions.
Finally I also want to thank the Valle Scholarship and Scandinavian Exchange Program for
generous funding throughout my graduate work at the University of Washington.
vii
1. INTRODUCTION
As the outcome of the last 150 years of industry development and its impact on our environment
starts to become more evident, the awareness of environmental impacts due to design become
more and more important. The construction industry has one of the highest impacts on the
environment in regards to energy use, material use and waste products. Within the construction
industry, infrastructure construction or roadway design is one of the largest economic and also
material consuming industries in the U.S. Extensive programs for recycling and reuse of materials
have been developed to take care of waste and end-of-life products. While these efforts are strong
and have become part of industry practice, this is not sufficient to create sustainable products over
entire life cycles. All engineers, designers, decision makers and others involved in any design and
construction process make decisions which have impact on the environment. These decisions
need to be taken with a higher environmental awareness already in the design process.
A number of different tools used to help facilitate these decisions towards more sustainable
alternatives are available today. One tool that has rapidly gained popularity in the U.S. is the
LEEDTM (Leadership in Energy and Environmental Design) green building environmental rating
system developed by the U.S. Green Building Council (USGBC). What the system provides is a
common language in the building industry for the incorporation of more sustainable elements in a
project, and it is shown to provide an overall awareness of environmental impacts.
If a similar rating system could gain popularity for projects in the roadway industry as it has in
the building industry, this would provide a means for performance based improvements in terms
of environmental impacts. This would increase the awareness of environmental matters in part of
an industry with the highest impact on our environment and it would, as LEED has in the building
industry, cause a strong movement effect with new markets emerging providing more
environmentally sound solutions.
The use of an environmental rating system for roads would help designers, engineers and
planners to identify different environmental aspects of a project and hence clarify where options
and improvements could occur in the design process. At the moment no such environmental
rating tool exists for the construction of roads.
2. RESEARCH OBJECTIVE
This Masters thesis will look into the possibility of how an environmental rating system for
roads could be structured to impact and improve sustainability measures in roadway design. The
intent is to develop a framework for such a system for Washington State and research how the
categories and credits could be put together. This include:
Define, classify and characterize elements in a roadway construction project and
3. METHODOLOGY
3.1 LITERATURE REVIEW
The literature review worked as a base in the research to find information to identify the
categories suggested for the environmental rating system.
The literature review provided data and information for classification and characterization of the
categories to be defined. This review looked into current trends in the road construction industry
in terms of new and older technologies promoting sustainability and environmental design. This
review also studied current regulations and legislatures for environmental design that needs to be
addressed in a project. There are Federal requirements, State requirements, Local ordinances and
other agency requirements and regulations to be considered. No rating system can be developed
without taking these regulations into consideration.
3.2 CLASSIFICATION OF DESIGN CATEGORIES
This effort defined broad processes involved in a roadway project. Design options and
technologies were identified and compared. The LEED program was studied carefully in order to
assist in determining credits applicable in roadway design and construction. Interviews were held
with professionals in the construction industry and other state or federal organizations to learn
about the impacts and implementation of LEED. Interviews with contractors/designers working
with LEED today helped identify advantages and disadvantages with the current LEED system.
3.3 DEVELOPMENT OF A RATING SYSTEM
The last part of the project was to develop a framework for an environmental rating system for
roadway design and construction using the characterization and classification information as a
base. Pollution prevention opportunities were identified for each category and discussed.
Categories were given different amounts of credits based on these pollution prevention
opportunities, and these credits were analyzed for requirements and feasible limits to be reached.
4. BACKGROUND
When using the LEED system as a model for this thesis, it is important to remember that the
difference between a roadway and a building is significant. A building is a point source impact
with complicated mechanical systems within the boundaries of the building, such as the walls.
The environment of concern is to a large extent the indoor environment and the closest
surroundings outside the building.
A roadway is a point source impact in the cross-section of the road, but in addition to this also a
linear impact where the impact runs through the landscape; urban areas, rural areas, different
geographic regions with a variety of bio-regions with different sensitivities and properties. This
makes the impacts from a road more complex and far-reaching compared to a building.
Median strip
Shoulder
Surface Course
Base Course
Subbase
Subgrade
5
be used in roadway construction (Carpenter et al, 2006). In addition to this large quantities of
steel, water, cement and bituminous products are being used as well. The manufacture and
extraction of these materials is not only depleting natural resources; all activities related to
managing the material such as extraction processes, production of new construction materials and
all activities needed for transport are also significant.
Most road construction taking place today is rehabilitation or repairs of existing roads. A majority
of the public paved roads in the U.S. are paved asphalt roads (about 93 %). In Washington State
about 87 % of paved roads are surfaced with asphalt materials and about 13 % with Portland
Cement Concrete (PGI, 2003). Rehabilitation and maintenance of these roads has to take place
regularly depending on pavement type. As one example most of the PCC sections of the interstate
highways in Washington State are reaching or have already reached the end of its design life.
This means large quantities of waste products will be generated (such as PCC and steel) and large
quantities of virgin materials will be required to replace them.
Approximately 4.1 billion metric tons of non-hazardous solid waste materials are generated
annually in the U.S. (AASHTO; 2005). When recycling of material and reuse of some of these
quantities have several potential uses in the roadway environment (Eighmy; 2001) there are also
other measures to define if a road could be called green or not. Some of these measures will be
described in this report.
5.1.1
LEED is a systematically organized system where design teams can aim for a level of
certification. The standards are divided into categories by significant environmental importance
and each category is divided into a certain number of credits for the design team to incorporate in
their design. The LEED standards are developed to cover environmental actions in the following
categories:
Sustainable Sites
Water Efficiency
Each category has prerequisite credits that need to be fulfilled and a number of optional credits
for the project to apply for. In LEED for New construction (LEED-NC, v. 2.2) a total of 69 points
are available within four categories of certification (USBGC 1, 2006):
LEED CertifiedTM for buildings that earn between 26 and 32 of the available points
LEED SilverTM for buildings that earn between 33 and 38 of the available points
LEED GoldTM for buildings that earn between 39 and 51 of the available points
LEED PlatinumTM for buildings that earn 52 or more of the available points
The project team decides which and how many credits to apply for and provide all the
documentation required by the USGBC. The design team makes sure the features of the credits
are incorporated in the design, and the construction team makes sure the features of the credits are
being met in construction.
5.1.2
Today there are more then 5000 certified LEED buildings (all levels of certification) in the U.S.
and to some extent internationally, compared to only 100 in 1998 (USGBC, 2007). One of the
major advantages with such a system is the provision of a checklist of environmental features
for a project outside the basic requirements, and the creation of a common standard of
measurements for sustainable design.
Meanwhile LEED NC version 3.0 is under development, some opponents claim a rating system
like this does not always provide the most sustainable product. LEED is criticized for not giving
performance based credits where the weighting of the credits give an accurate estimation of
environmental impacts and importance. This is true; LEED is not an absolute measure of
sustainability. The important result is however how the implementation of the LEEDTM rating
system has changed the building construction industry (in some parts of the U.S.), the last 5-10
8
years in regards to the use of more sustainable and environmentally sound construction solutions.
For impacts of LEED in the building industry, see Chapter 14; Implementation Strategy and
Impacts.
The rating system developed in this thesis and the definition of elements in a roadway project is a
step in the same direction.
Category Intent
The intent with this category is to reduce impacts in the
environment due to the alignment of the road such as:
preservation of wetlands, forests, farmlands, and other
ecological sensitive areas.
Construction Activities
(CA)
10
11
Reduce emissions
12
Divert material from Landfills:
Landfills require large amounts of land and produce large amounts of emissions. In the United
States, landfills are the largest source of methane (CH4) emissions caused by humans (EPA,
2002). (Methane has a higher Global Warming Potential (GWP) than carbon dioxide (CO2) and is
a huge contributor to climate change, larger then carbon dioxide.) Over 2,100 operational landfills
exist in the United States (EPA, 2002), but many of the landfills in the U.S. are estimated to shut
down in the next 10 years (Amirkhanian, 2001). In Washington State in 2005 there were 18
municipal solid waste (MSW) landfills, 29 inert landfills and 10 limited purpose landfills located
around the state (Washington State Department of Ecology, 2005). Solid waste landfills reported
in 2005 a statewide permitted landfill capacity of 219 million tons, or approximately 40 years at
the current rate of disposal. The reduction of materials disposed in landfills is needed.
Economic Benefits:
The economical benefits of recycling or reuse of materials can be direct as well as indirect.
Avoided direct costs can be tipping fees for material disposal and reduced transportation as well
as production cost due to material recovery. If transportation distances are reduced this can also
have an indirect cost benefit in less wear on the existing roadway system (FHWA, 2004, Horvath,
1999).
8.1.1
Terminology
13
generated in a process and capable of being reclaimed within the same process that generated it
(ISO 14021, 1999). Examples in this category include, sawdust, chips, and trimmed materials.
Post Industrial, is a term currently being phased out (according to ISO 14021, 2004), and
replaced by the definition for pre-consumer materials.
Recycled content is defined as the proportion, by mass, of recycled material in a product or
packaging. Only pre-consumer and post-consumer materials shall be considered as recycled
content (ISO 14021, 1999).
Diverted materials are materials that were previously disposed in landfills or incinerators but are
taken from the waste stream as new markets have emerged. This can be construction and
demolition debris that is being reused or recycled.
Inert materials, or wastes, are chemically and physically stable materials that do not undergo
decomposition, such as sand, bricks, concrete or gravel.
8.2 WASTE, RECYCLING & ROAD CONSTRUCTION
The 4 million miles of existing roadways in the U.S. (as mentioned in Chapter 4.1) need regularly
rehabilitation or replacement work. Portland Cement Concrete (PCC), hot mix asphalt (HMA)
pavements and base materials in existing roads, bridges and other infrastructure elements provide
a huge resource of materials for possible future use. Figure 2 present an overview of major
materials to be used in a highway environment. Whereas guardrails, signs and other objects along
the road require materials as well, the major quantities of materials required is in the pavement
structures itself. The Materials & Resources category will focus on these major materials.
14
8.2.1
Consistent numbers of building construction and demolition debris can be found (EPA, 1998),
whereas quantities used in road applications are often not studied to the same extent. However,
Figure 3 presents production and consumption of some road construction material in the U.S. that
can be used to get a general idea of quantities by source and market sector (1996 figures) for
roads.
15
A large part of the crushed concrete debris was in 1996 sent to landfills, and a large part was used
as new road base material. This is the most common way of using recycled concrete in roadway
applications, as described in Design Options. Even if a large part of the crushed PCC still goes to
landfills, the use of recycled PCC is however increasing in construction applications due to new
emerging markets and recycling programs. See Figure 4 for Washington State as an example of
increase in PCC recycling.
The HMA industry in the U.S. produces over 90 million metric tons of HMA waste annually,
with over 73 million tons being recycled (Decker, 2007, Wilburn, 1998). This makes this product
one of the most recycled products in the United States. Most of the recycled HMA is used as part
16
of producing new HMA, see also Design Options, but still some of the recycled asphalt ends up
in landfills or in stockpiles.
One important construction material that is not included in these graphs is steel. Steel is also one
of the most recycled materials in the U.S with around 76 million tons of steel recycled (or
exported for recycling) in 2005 (SRI, 2006), where around 7 millions were used to produce new
reinforcement bars in 2002 (CRSI, 2002). Continuously Reinforced Concrete Pavement (CRCP)
became popular with the construction of the U.S. Interstate Highway system in the 1960s and
1970s and hence contains large amounts of steel. Also dowel bars contain steel. It is estimated
that about 65% of all reinforcement bars and nearly 100% of structural steel beams and plates
used in construction are recycled into new products (SRI, 2006). This includes building as well as
road construction steel. There are no separate data available for dowel bars specifically.
8.2.2
The recycling rate of construction and demolition debris has shown to increase dramatically as
the trend of new market areas has developed. In Washington State the Department of Ecology
started to keep track of the diverted materials in 1999 as they noted this very large increase of
material recovery outside the traditional solid waste stream. In 2005 construction and demolition
related materials represented about 95% by weight of the diverted materials reported in
Washington State. Asphalt and concrete alone account for 67% of these total diverted materials
(Washington State Department of
Ecology, 2005). Figure 4 presents as
an example the increased rate of
asphalt and concrete recycling from
the end of the 90s until today. (Note
that the use of recycled asphalt
pavement (RAP) in new pavement
started much earlier than 1999 but this
is the year the Department of Ecology
started to keep track of this material.)
Figure 4. Asphalt and Concrete Recycled in Washington State
(Washington State Department of Ecology, 2005)
17
There are five major types of final uses for diverted materials defined by Washington State
Department of Ecology. They are 1) transforming or recycling into the same or other products, 2)
burning for energy, 3) reuse, 4) use as aggregate material for other products, 5) composting. This
credit will be an incentive to use 1, 3 and 4 of these types of final uses for roadway construction.
8.3 DESIGN OPTIONS
The construction applications presented in Figure 2 that require large volumes of materials can be
defined in major categories (Simon et al, 2006; FHWA, 1997). They are:
(1) Asphalt paving applications
(2) Portland cement concrete applications
(3) Flowable fill applications
(4) Stabilized base applications
(5) Unbound aggregate and fill applications
These applications all have the opportunity to use reused or recycled materials, which for the
most part consists of recycled aggregates. The variability in the products in terms of technical
characteristics can limit their use however the opportunities for innovation and design alternatives
exist. Some material types have one unique final function but there is often more than one final
use for a material depending on the market prices and demand and the amount of research
performed for the specific use. This can provide very important information of feasibility. On
next page, Table 2 presents an overview of the waste or by-product that could be used as a
replacement material to a virgin material in any of the applications listed previously. The table is
extracted from User Guidelines for Waste and By-products Materials in Pavement Construction
(FHWA,1997).
18
Table 2. Waste or by-products to be used by application
(FHWA,1997)
APPLICATION USE
Asphalt Concrete Aggregate
(Hot Mix Asphalt)
Embankment or Fill
MATERIAL
Blast Furnace Slag
Coal Bottom Ash
Coal Boiler Slag
Foundry Sand
Mineral Processing Wastes
Municipal Solid Waste Combustor Ash
Nonferrous Slags
Reclaimed Asphalt Pavement
Roofing Shingle Scrap
Scrap Tires
Steel Slag
Waste Glass
Coal Bottom Ash
Reclaimed Asphalt Pavement
Blast Furnace Slag
Coal Boiler Slag
Steel Slag
Baghouse Dust
Sludge Ash
Cement Kiln Dust
Lime Kiln Dust
Coal Fly Ash
Roofing Shingle Scrap
Scrap Tires
Reclaimed Concrete
Coal Fly Ash
Blast Furnace Slag
Blast Furnace Slag
Coal Boiler Slag
Mineral Processing Wastes
Municipal Solid Waste Combustor Ash
Nonferrous Slags
Reclaimed Asphalt Pavement
Reclaimed Concrete
Steel Slag
Waste Glass
Coal Fly Ash
Mineral Processing Wastes
Nonferrous Slags
Reclaimed Asphalt Pavement
Reclaimed Concrete
Scrap Tires
Coal Bottom Ash
Coal Boiler Slag
Coal Fly Ash
Cement Kiln Dust
Lime Kiln Dust
Sulfate Wastes
Coal Fly Ash
Foundry Sand
Quarry Fines
Coal Fly Ash
Cement Kiln Dust
Lime Kiln Dust
19
A short description of the most commonly used applications follows with information regarding
origin, technical properties and influences in the pavement as well as commonly used ranges of
the material in pavement applications in DOTs around the United States.
8.3.1
Reclaimed asphalt pavement (RAP) is defined as salvaged, milled, pulverized, broken, or crushed
asphalt pavement (AASHTO, 2005). RAP consists of graded aggregates coated by asphalt cement.
These aggregates can be reused as aggregate in new hot mix or cold mix asphalt, or if graded in
larger pieces as aggregate in fill or base material. If used as aggregates in new mix, the coating of
the RAP also contributes to the binding agent in the mix. This contribution can result in a slight
reduce in binding agent.
State DOT specification requirements for the use of RAP in HMA paving varies from 15 up to
70% by total weight of the mixture (Horvath, 2003). The most commonly used rate is between 20
to 50%. WSDOT allows a maximum of 20% RAP that can be included in HMA, see also WA
Requirements.
RAP can be used to a larger extend as a base or fill material, however one discussed limitation of
using RAP as fill material is the unknown risk of leaching of pollutants from the aggregate to the
environment. Rainwater may leach chemicals from this material either during stockpiling before
recycling or due to infiltration through the pavement surface containing RAP.
A field study in Florida
indicates that this is not a
problem (Townsend, 1998),
where chemicals investigated
were
volatile
compounds
(VOCs),
polycyclic
aromatic
hydrocarbons
heavy metals.
Figure 5. Stockpiled RAP
(SRA, 2005)
organic
(PAHs),
and
20
The Swedish Road Administration (SRA, 2004) state leakage from stockpiles is not a significant
problem for organic and inorganic substances, however another study (Norrman, 2005) has
shown larger amounts of chloride and lead is indicated in the groundwater due to stockpiling of
RAP.
A study by Legret et al. (2005) comparing new asphalt containing 10% respectively 20% of RAP
shows no obvious difference in leaching rates of heavy metals, even though comparing this RAP
to regular HMA indicate that concentrations of total hydrocarbons and some PAHs were higher
in leakage from RAP.
One way to avoid leakage during stockpiling is to cover the piles, however, the importance is also
to find how the RAP perform as part of the pavement structure. More research in various
locations, climates and situations needs to be evaluated to find the true impacts of this material.
Current research performed indicate mixed results.
8.3.2
Recycled Concrete Pavement (RCP), also known as crushed or rubblized concrete, is reclaimed
PCC pavement material. Primary sources of RCP are demolition of existing concrete pavement,
bridge structures, curb and gutter, and from recyclers who obtain old PCC from
commercial/private facilities (AASHTO, 2005). RCP is also called Recycled Concrete Material
(RCM) or Recycled Concrete Aggregate (RCA). In this report crushed concrete pavement will be
referred to as Recycled Concrete Material as the origin of the PCC can be elsewhere than from
pavements.
The main use of RCM in new pavement structure is as a new base or fill material. In Washingon
State as well as in most States in the U.S. RCM is allowed to be used in road base, as drainage
aggregates and as backfill material (WSDOT, 2004; FHWA, 2004 ). Up to 100% of the base
material could consist of RCM.
RCM can also be used as coarse and/or fine aggregate in PCC pavements as part of the mix, but
there are some limitations to this (RMCR, 2006). Incorporating more than about 10 to 20 % of
fine RCM aggregates can cause a reduction in quality (FHWA, 2006). RCM as fine aggregate in
new PCC is limited, if even allowed, to 20% by many agencies, this partly due to some problem
21
found with workability, decreased compressive strength and higher water demand (FHWA, 2003).
In Washington State RCM as fine aggregate in new PCC is not allowed, see also WA
Requirements.
As for RAP, there are concerns of leakage impacts using RCM as new aggregates. The reclaimed
concrete has a high alkaline content and a relatively high degree of solubility of these alkaline
materials (AASHTO, 2005). The result is a potential increase in pH that can occur in waters
seeping through the RCM aggregate base or the new PCC.
8.3.3
Steel
Steel is a highly recycled material used as dowel bars or reinforcement in concrete pavements and
bridges. As concrete is demolished and crushed, any reinforcement bars in the structure is
separated as ferrous scrap. The reinforcing bars are then melted down to create new steel products.
There are mainly two processes used to create new steel products; the Basic Oxygen Furnace
(BOF), used primarily for flatrolled steel such as automobile bodies or appliance shells, and the
Electric Arc Furnace (EAF), typically used to create long shapes, which includes reinforcement
bars (SRI, 2006).
In steel recycling the material does not loose its properties and strength. In the process of making
new steel products, old scrap is always used and the demand for steel scrap is even higher than
the availability. This makes steel a strongly recycled material with many opportunities for
recycling over its entire life time.
The recycled content in the production of new reinforcement bars (the EAF method) is as high as
95% (CRSI, 2002). As mentioned previously The Steel Recycling Institute estimates that in 2006
around 65 percent of reinforcing bars were recycled (SRI, 2006). This indicates a possibility to
increase the rate of reinforcement recycling.
8.3.4
Slag cement, or ground granulated blast furnace slag (GGBFS), is a material that results from the
processing of molten slag from an iron blast furnace (SCA, 2005). This is a cementing material
that can be used to partially replace portland cement in concrete. The use of blast furnace slag has
increased considerably in recent years and this trend is expected to continue (Malhorta, 1999).
22
Suggested replacement of portland cement with slag cement is 25-50 % by the Slag Cement
Association (SCA, 2005). This depends on the application and the particluar cicumstaces. It is
substituted for portland cement on a one-to-one basis by mass. The proportions are dictaded by
different requirements for strength, durability, time of set, heat generation, or resistance to alkali
silica reaction (ASR) and sulfate attack. (This is a form of concrete deterioration occurring when
concrete comes in contact with water containing sulfates (SO4)).
Apart from the possibility of replacing some of the portland cement it has other attributes
impacting the concrete. Better workability, higher
strength, lower permeability and improved resistance
to aggressive chemicals (SCA, 2005) are some of the
qualities found by using part slag cement in concrete.
It also has lighter color contributing to higher albedo
conforming to Credit EEC-1 (Chapter 10; Energy &
Environmental Control).
Figure 6. Slag cement
(SCA, 2005)
If used more than 25% in the cement material in PCC it is found that the slag increases the time
of set. When substituted for portland cement in quantities between 25- 65%, slag cement
significantly reduces the permeability (SCA, 2005).
The availability of Slag Cement is in the U.S. is high. However, currently in Washington State
most of the slag used is imported from Japan (Correspondence with Rob Shogren, Technical
Service Engineer, Lafarge North America, February 2007). This does add some cost to the
material however it is still cheaper than conventional cement. The important question is what this
transportation activity does to the environmental impacts embodied in the material. Incentives for
locally made materials should be given.
8.3.5
Fly-Ash
Coal fly ash, usually referred to as fly ash, is a combustion material remaining in the combustion
of coal consumed to generate electricity. Coal is not all carbon, and fly ash is the mineral remains
23
from combustion in the form of a fine powdery ash (ACC, ACCA, 2006). This material can be
used as replacement for some of the portland cement in concrete pavement as well as fine
aggregate in asphalt pavements. It can also be used in stabilized base course, flowable fills and
embankments (FHWA, 2003).
Fly ash is classified as either Class C or Class F, depending on the materials chemical
composition. Class C ash is also referred to as high calcium fly ash because it typically contains
more than 20 percent CaO. Class F, or low calcium fly ash has less than 10 percent CaO (FHWA,
2003).
Some of the benefits of using fly ash in concrete include increased strength, increased workability,
decreased permeability, reduced heat of hydration, higher resistance to sulfate and other chemical
attack (ACA&ACAA,2006; SCA, 2005; EPRI, 2002). Fly ash is typically used to replace 20-40%
of the Portland cement in a concrete mix (ACAA, 2006, FHWA, 2003).
In asphalt mixtures fly-ash can be used as substitute for some of the fines aggregates, as well as
part of asphalt concrete base courses. Most asphalt mixtures contain 3-7% fine aggregate to
ensure cohesiveness, and base courses usually 12-24%. Fly ash in asphalt pavements is found to
increase the stiffness of the asphalt, improve the rutting resistance of pavements, and the
durability of the mix (FHWA, 2003).
Considerations to take into account in using fly-ash as a replacement in PCC is it can increase air
entraining properties and also has lower early age compressive strength (ERIS, 2002, FHWA,
2003). It is agreed that not all the available fly-ash is suitable for use in concrete. (Malhotra,1999).
The two most important parameters of a fly-ash for concrete use is the fineness and carbon
content.
Availability of fly-ash Class F is limited in Washington. Most of the fly-ash is imported from
Alberta (Canada) and Montana, however some of this fly ash is of type C (correspondence with
Rob Shogren, Lafarge, North America, February 2007; and Jeff Uhlmeyer, WSDOT, February
2007). As with the use of slag cement, considerations should be taken to the embodied impacts
the transportation activities bring to the materials.
24
In addition to fly-ash, other coal combustion products can be used as well, such as Bottom Ash
witch is a heavier ash particle that basically falls to the bottom of the power plant boiler.
Bottom Ash is usually used in structural fill applications and as aggregates in manufacturing of
concrete bricks (ACA&ACAA, 2006).
8.3.6
Glass
Crushed glass or glass cullet, is made of recycled glass products. The quality of the glass varies
and it is important to process it properly to separate the glass from dirt, paper and plastics before
appropriate gradations. If the glass is properly processed it can have characteristics similar to that
of a gravel or sand. It is usually used as a substitution for aggregates in base courses or fills, but it
has also been used as an aggregate substitute in asphalt pavements. Asphalt containing glass
cullet as an aggregate is also called glassphalt (NAPA, 2006).
U.S. DOTs usually allow between 10-20% of crushed glass in base course, and in some cases as
much as 30% in the subbase (RMRC, 2000).
Long term performance of using recycled glass in pavements is at an early stage in research.
Glass aggregate has showed problems in both asphalt concrete and PCC pavements (IDOT, 2002).
In concrete pavements, this material is problematic due to the harmful alkali-silica reaction with
the cement paste. In bituminous pavements, this material bonds poorly to the asphalt, which
results in stripping and raveling problems.
8.3.7
Scrap Tires
In the U.S. approximately 280 million waste tires are produced each year (FHWA, 1997,
Amirkhanian, 2001). In Washington State, approximately 4 million tires were reported as waste
in 2004 (Washington State Department of Ecology, 2005). Of these tires about 55% were
recycled (or diverted), about 23% went to tire-derived fuel, and about 22 % went to landfill
disposal. Over the United States, approximately 800 million scrap tires are currently stockpiled
(Amirkhanian, 2001). This is a huge source of material.
Ground or crumb rubber can be included in asphalt pavement in two principal ways. In the wet
process the crumb rubber is blended with the asphalt binder as a modifier (it increases its
viscosity) (FHWA, 1997). Typically the content is 15-20% of rubber by weight of asphalt. The
25
product resulting from the wet process is called asphalt-rubber cement. In the dry process the
rubber is blended directly into the HMA (Iowa DOT, 2002). The product resulting from the dry
process is called rubberized asphalt. The crumb rubber content blended in the mix is usually 1225% rubber by weight of mix (FHWA, 1997).
Most laboratory and field experiments indicate that the rubberized asphalt mixtures, in general, show
an improvement in durability, crack reflection, fatigue resistance, skidding resistance, and resistance
to rutting (Hicks et al. 1995; Xiao et al, 2005, Amirkhanian, 2001). Another important finding is the
fact that asphalt containing rubber can reduce tire-pavement noise (Munden, 2006).
The most common objections to using asphalt rubber is high initial costs, issues with recyclability
of the rubberized pavements, hazardous emissions and expensive equipment modifications (to
produce the new asphalt).
8.3.8
Shingles
Shingles contain about 20 % asphalt binder by weight (Mallick et al, 2002) and in many ways
asphalt shingles closely resemble RAP (Amirkhanian et al, 2001). Sources of recycled asphalt
shingle are either the by-product or scrap from the manufacturing of roofing shingle, or, the
construction debris generated when shingle roofs on buildings are removed. Shingles can be used
to modify the asphalt binder, but can also work as an aggregate substitute (FHWA, 1997). Use in
HMA can reduce the need for new asphalt binder significantly, hence cost as well as the need for
new materials.
The results from a study performed in Massachusetts show that the use of manufactured waste
shingles in HMA does not cause a significant difference in the quality of the HMA. The rutting
resistance is even shown to be improved by using manufactured waste shingles. (Mallick et al,
2000). Other benefits using shingle in HMA can be increased stability, decrease in temperature
susceptibility, improved compaction, and improved smoothness (CIWMB, 2006).
Many state DOTs in the US allows 5% of asphalt roofing shingles in asphalt pavements
(CIWMB, 2006). The quality of the recycled shingle depends weather it origins as a by-product
from manufacturing of new shingle or as a waste from old roofs. Many state DOTs only permits
recycled shingles sourcing from the manufacturing process and not the scrap shingle from old
roofs (RMRC, 2003).
26
8.3.9
Foundry sand
Recycled foundry sand (RFS) or Waste Foundry Sand (WFS) is silica sand with many of the
same properties as natural sands. It is a byproduct of the ferrous and nonferrous metal casting
industry, where sand has been used as a molding material (AASHTO (NCHRP), 2006)
It can be used in many of the same ways as natural or manufactured sands. This includes many
roadway construction applications such as embankments, flowable fill, HMA and PCC (FHWA,
2004). It can also be blended with either coarse or fine aggregates and used as a road base or
subbase material.
Studies have shown that foundry sand can be used to replace between 8 and 25% of the fine
aggregate content in HMA (FHWA, 2004, AASHTO, 2006) and as much as 45% of the fine
aggregate in concrete (AASHTO, 2006).
DOTs in the U.S allows the use of recycled foundry sand in HMA between 5-20%.
It is important that the foundry sand is cleaned of clay, dust, and other toxic materials.
Additionally, metals present in the sands need to be removed either manually or magnetically.
Foundry sand properties vary in samples taken from one foundry, and there is increased variation
from foundry to foundry. This makes it difficult as a reliable source of material for road
construction.
Foundry sand is gray to black. In some concretes, this may cause the finished concrete to be
darker which may not be desirable.
The leakage rate of chemicals to stormwater runoff from the use of foundry sand is found to not
be worse than that from natural soil (FHWA, 2004).
8.4
When reusing materials as well as recycle materials, consideration has to be taken to the actual
processes involved. Sometimes a pre-consumer or post-consumer material has to go through
additional industrial processes before being feasible as a construction material.
27
The opportunity to use pre-consumer materials (previously post-industrial) as part of a roadway
structure is like described in previous sections big. Fly-ash and slag cement, both materials
produced in other industrial processes, are good examples of this. No additional energy is
required, no additional emissions are released as the main process is taking place anyways. Figure
7, 8 and 9 shows comparisons in terms of embodied environmental impacts of fly-ash, slag
cement and conventional portland cement production.
The reduction in embodied green house gas emissions in concrete production is measured by CO2.
By using a 50 percent slag cement substitution as an example, a 42 to 46 percent reduction in
greenhouse gas emissions can be achieved (SCA, 2005).
28
One ton of Portland cement requires about 1.6 tons of raw material, because of mass lost due to
emissions and other factors (Malhotra,1999) Substituting 50 percent slag cement can save
between 6 and 15 percent of embodied virgin material extraction (SCA, 2006).
The opportunity to use post-consumer materials is large too, especially the reuse of demolished
PCC (RCP), reclaimed asphalt pavement (RAP) and base material as discussed earlier.
From a pavement design perspective, recovered materials should be used in such a manner that
the expected performance of the pavement will not be compromised. Increasing the use of
recycled materials can lead to decreased durability of the pavement, as one example. Careful
design and research has to be carried out to find appropriate limitations.
8.5 COST
Cost is an important factor in terms of recyclability and reuse of material and can be an incentive
to use such material. The construction industry is already recognizing the economic benefits of
using recycled materials, such as crushed PCC and aggregates for roadbase, and steel as an
example of very high recycling rate which originally derive from the economical benefits of using
used steel. The cost-effectiveness of substituting conventional aggregate with recycled materials
is highly dependent on the location, the quality and cost of local aggregates. Comparable figures
are very difficult to find in the literature depending on these local conditions and equipment cost.
Recycling versus tipping fees and distances to landfills are other important aspects for the
feasibility of recycling.
In some urban areas recycling can be more profitable than in rural areas. In rural areas recycling
can be expensive and impractical due to high transportation cost and the lack of nearby materials.
29
On the other hand, if materials are available, reuse of materials that otherwise have to be
transported can be very cost effective. Whatever is the closest and cheapest alternative can be
considered to be the most attractive.
8.6 LIFE CYCLE ANALYSIS ENVIRONMENTAL FOCUS
Discussing materials and resources and their environmental impacts is not only about
recyclability and the reuse of materials. One of the most important approaches to every design
that should be made is to look at the total life cycle impacts of the material. Life cycle analysis
(LCA) focusing on cost is usually carried out for projects. Life cycle analysis focusing on
environmental impacts is related to these costs and has to be considered as well.
The life cycle consists of many different processes and activities and for a pavement construction
the main activities can be categorized in: the extraction of the material, the production of the
material, all the transportation activities related to these activities, the construction activities
related to the placement of the material, the maintenance activities related to the structure and the
end of life of the pavement.
All these stages uses materials, require energy and release emissions contributing to the overall
environmental impacts from the pavement over its entire life. All these stages also relate to many
other activities and processes that use materials, consume energy and release emissions as well.
The cradle to grave of many processes that interrelate is included in a LCA. Chemical leakage,
the embodied energy content and the embodied greenhouse gas emissions are some measures that
can give a sense of how the materials really perform. Using virgin materials may not be superior
to using recycled materials (Carpenter et al, 2006).
Using recyclable materials may decrease the life of the pavement, and if this is the case, the
overall embodied energy content and embodied emissions content might be higher than if using
conventional materials (due to the increase in construction and maintenance activities this shorter
life of the stucture brings).
There are a wide variety of LCA approaches and design tools available in the market. It is a
complex process to carry out detailed LCAs with environmental focus, and its a matter of
setting up boundaries for when the cycle starts and where it ends, what processes to include and
30
what material flows to study. Once performed however, it can provide the very useful information
needed to decide weather one approach is superior to another.
8.6.1
The Pavement Life-cycle Assessment Tool for Environmental and Economic Effects (PaLATE)
is a design tool developed at the University of California at Berkeley for the Recycled Materials
Resource Center (RMRC) and the FHWA (Horvath, 2003). It provides a life-cycle assessment
(LCA) framework and computer-based tool including environmental and economic parameters
for evaluation of pavement construction. The purpose of this tool is to assists decision-makers in
evaluating the use of recycled materials in highway construction and maintenance activities
(Horvath, 2003).
This tool evaluates the environmental performance of emissions and energy use associated to
construction, transportation and maintenance of asphalt and Portland cement concrete pavement,
subbase, embankment and shoulder material. It provides an assessment of the use of recycled
material from demolished pavements as well as an assessment of industrious by products that
may be used in road construction and pavement structures. It also performs an analysis of life
cycle costs. The results between different design alternatives can be compared to each other in
regards to these environmental as well as economical performances.
The results are provided in graphs describing each phase, effects from processes, material
transportation and materials production. This tool can be very helpful in deciding between design
options and the feasibility of actual environmental and economical impacts. Credit will be given
for analysis performed in PaLATE.
8.7 TRANSPORTATION ACTIVITIES
The effects of transportation on fossil fuel consumption and the resulting pollution is well
established and it is significant (EPA, 2002). The construction of roads certainly include large
masses of materials that needs to be transported over great distances. This impact not only release
air pollution and consumes fossil fuel, but also has impact on infrastructure maintenance in terms
of road usage.
In regards to the use of material and resources, the effect of transportation of these materials has a
considerable effect on the actual impact over the entire life cycle of the material. The use of fly-
31
ash and slag cement as replacement in PCC is increasing in Washington state, but the availability
of theses materials from this region is low. Large quantities of slag cement is imported and
transported from Japan. Fly-ash is available in Washington State and in Oregon, but large
quantities are also imported from Alberta, Canada. This needs to be addressed and could be
considered in an LCA. Additionally, to use regional or local products can support regional
economies by promoting growth for local businesses. See Appendix A for evaluation of
recyclable materials and their availability, and see Appendix E for available virgin quarries and
pits in Washington State used by WSDOT for HMA and PCC pavements.
LEED-NC (v. 2.2) credit MR 5 award building materials or products that have been extracted,
harvested or recovered, as well as manufactured, within 500 miles of the project site for a
minimum of 10% (based on cost) of the total materials value. This measure can provide an
incentive for the above mentioned aspects and this credit will be adapted to this system as well.
8.8 REGULATIONS IN WASHINGTON STATE
WSDOT Standard Specifications (WSDOT, 2006) state requirements and limitations for the use
of recycled content in materials in pavement applications. Before setting criteria limits, these
regulations needs to be considered. General Requirements for Recycled Materials are stated in 903.21.
Fly-Ash
Fly ash may be used in cement concrete pavements and shall not exceed 35 % by weight
of the total cementitious material (5-05.3(4)). It shall conform to (9-23.9) and shall be
limited to Class F with a maximum CaO content of 15 % by weight.
32
Slag Cement (Ground Granulated Furnace Slag)
Ground granulated blast furnace slag may be used and shall not exceed 25 % by weight
of the total cementitious material (5-05.3(4)) and shall conform to (9-23.10).
When both ground granulated blast furnace slag and fly ash are included in the concrete
mix, the total weight of both these materials is limited to 35 % by weight of the total
cementitious material.
Glass
Recycled glass may be used as ballast, shoulder ballast, crushed surfacing and gravel
aggregate up to 15% by weight as noted in 9-03.21(4). As foundation material and gravel
backfill in certain situations 100% glass may be used as stated in 9-03.21(4).
These are the mentioned recyclable materials in WSDOT specifications. As mentioned previously,
there are other materials to be used as replacement of virgin materials and these could be
considered as well. Following information in addition to the specifications was retrieved by
correspondence with Linda Pierce, State Pavement Engineer, WSDOT, February 2007:
Scrap Tires are not prohibited to use but need to get special approval.
Shingles are currently not being used by WSDOT.
Glass is being allowed as stated above but is not being used, mainly due to cost.
33
8.9 CRITERIA DEFINITIONS
A total of 8 credits can be achieved in this category; Materials & Resources (MR).
Table 3. Credits available in category Materials & Resources
Materials & Resources (MR)
Credits
Reuse of Pavement 1
Reuse of Pavement 2
Recycled Content 1
Recycled Content 2
Environmental credit is given to reuse and recycling of asphalt, PCC and other pavement
materials to substitute for virgin material production and minimize impacts related to this activity.
The life of recycled pavement materials starts at breaking up existing old pavement, followed by
transportation to deposit or asphalt/concrete plant, followed by crushing, mixing of new pavement
material and transportation to the location of the new pavement.
The life of pre-consumer materials starts at the end of the manufacturing process, such as the
product of fly-ash in the combustion process, or slag cement in the furnace.
A description of the credits with their intent and requirement follow.
34
8.9.1
The intent of this credit is to reduce the amount of waste going to landfills or incineration and
provide an incentive to include waste management practices in the project.
1 Credit
A plan for handling construction waste in the project should be submitted including calculation of
percentage of construction demolition waste (CDW) according to the recycling rate calculation
(modified from LEED v. 2.2):
CDW Re cyclingRate[%] =
Re cycledWaste[volume]
Re cycledWaste[volume] + LanfilledWaste[volume]
Comments:
A possibility of earning a greater beneficial impact from the Construction Waste Management
credit could be to weight specific wastes depending on their impacts in regards to availability and
to promote recycling of specific materials depending on regional priorities or waste prevention
strategies. This should be developed in between agencies and their decisions.
35
The 70% limit comes from the fact that about 67% of total diverted materials related to
construction in Washington State account for asphalt or concrete debris as described in Chapter
8.2.2., Construction Debris in Washington State. (Diverted material means materials taken from
the solid waste stream that previously ended up in landfills but now are being used in new
products). These numbers are approximate but can give an indication of quantities that are being
reused or recycled.
36
8.9.2
The intent of this credit is to salvage construction materials in the project to reduce the extraction
of virgin materials and/or production of new materials including all processes involved in theses
activities.
Reuse of Materials 1
1 Credit
Example:
Reuse PCC pavements, asphalt pavements or reuse native soil, sand, gravel and rocks for new use
in top courses, base courses, embankments and fills.
Re usedRate[%] =
Re usedmaterial [tons ]
Basematerial [tons ]
Or
Re usedRate[%] =
Re usedmaterial [tons ]
TotalMaterial [tons ]
A description of the material to be reused and its new application should be submitted together
with the estimates.
37
8.9.3
1 Credit
38
8.9.4
The intent of this credit is to promote the use of recycled material to minimize the extraction of
virgin materials and impacts from production processes as well as reduce waste.
Recycled Content 1
1 Credit
Example:
Binding mediums material would be one assembly group, aggregates used another, steel another,
etc. Use the Application Table 2 in Design Options for assembly groups. See Appendix B for
examples.
Assembly Re cycledContent[%] =
HMAandPCC Re cycledContent[%] =
Example technologies:
Fly-ash, Slag cement, glass, scrap tires, foundry sand or shingles are possible recycled materials
that can replace part of the virgin materials. The use of RCP and RAP can contribute to this credit
as well.
39
8.9.5
1 Credit
Use recycled content additionally 10% (total 35%) in the HMA/PCC and
50% of the total material in the structure if base courses are included.
Comments:
Analysis of different pavement types, rehabilitation of commonly used pavements in Washington
State and the reuse of variations of the materials has been performed to set the criteria limits. See
Appendix B for example sheets.
The idea of credit MR-4 and MR-5 is derived from LEED-NC v. 2.2 credit MR 4.1 and 4.2,
Recycled Content in Materials and Resources.
40
8.9.6
The intent of this credit is to minimize the extraction of virgin materials, impacts from production
and construction processes, transportation as well as reduce waste and costs.
2 Credits
Perform a life cycle analysis in PaLATE and document the results for the
project alternatives for environmental impacts as well as costs.
Present the results with comparisons and describe the selected option for the project in which
categories it was beneficial in terms of energy, emissions, recycled materials quantities, leakage
releases, life cycle costs, etc.
Comments:
PaLATE is available from FHWA and the Recycled Materials Resource Center (RMRC). The
idea of this credit is to encourage the design team to think in life cycle terms of material and
construction alternatives and their environmental as well as economical impacts.
41
8.9.7
The intent of this credit is to reduce environmental impacts from transportation activities as well
as support regional/local economy.
1 Credit
In order to calculate the Local Regional Product Rate (LRPR) following equation can be used
(modified from LEED v.2.2).
The total material costs (excluding labor and equipment) of individual products that are
manufactured within 150 miles each contribute to the local regional product cost. If only a
fraction of a product or material is extracted/harvested/recovered and manufactured locally, then
only that percentage (by weight) shall contribute to the regional value (LEED NC v.2.2,
USGBC).
Comments:
This credit is benchmarked from USGBC LEED-NC v. 2.2, however a larger quantity is set as
limit compared to LEED-NC v. 2.2 due to the type of materials used in roadway construction, and
a lower radius limit is set as well (the radius limit is 500 miles in LEED). See Appendix E for
available virgin quarries and pits in Washington State used by WSDOT.
The radius can be discussed. An idea is to develop the credit and base the thresholds on ton-mile
values rather than only miles, which would include weight as well as distance, since weight also
an important factor in emissions rate and fuel needs. This should be further analyzed.
42
8.10 DISCUSSION
Quality of the products containing recycled material is often source dependent and careless use
can lead to bad performance. Specifications and requirements should of course be met in the first
hand, the intent of this category is to force additional innovative ideas in the design and give an
opportunity to design and get credit for this.
LCAs can determine the different parts of a materials cycle and their actual impacts on the
environment. Collection, transportation and processing of reclaimed material for recycling can
require significant amounts of energy depending on situation and methods. It can be the case that
different environmental goals collide, and trade offs will be the result.
In 2005, the Solid Waste and Financial Assistance Program (SW&FAP) at The Department of
Ecology in WA started a Green Building Partnership with Cascadia Green Building Council (The
North West Chapter of USGBC developing the LEED standard). This partnership is intended to
educate research and promote green building initiatives as a way to reduce waste and promote
recyclability. A similar partnership should definitely exist for the green road research and
construction of road industry as well.
For this category Materials & Resources, consider including credits for pavement markings,
railings and other smaller objects as well.
43
44
Reduction in infiltration:
A big percentage of the precipitation falling on a surface is supposed to infiltrate into the ground
contributing to groundwater recharge. Impervious areas create a reduction in this infiltration. This
can result in a decreased groundwater recharge (Brattebo & Booth, 2003) and therefore impact
the water table by allowing less water to be held in the ground. The reduction in infiltration can
dry up small streams and wetlands in the summer (WSDOT, 2006; LID, 1999) and cause aquatic
habitats to be uninhabitable during these times.
45
Water pollution:
As water runs off any impervious surface it picks up and mixes with materials on the ground,
some of which are known pollutants. Examples of these polluntants are oil, grease and coolants
from vehicles, fertilizers and pesticides from farming or gardening, soil from construction sites,
trash and animal waste. The dirty runoff then flows directly into streams, wetlands, rivers, lakes
and other waters without being treated and cleaned of pollutants. This polluted water impacts fish
and other habitat significantly (Department of Ecology, 2003), as well as groundwater quality and
swimming waters (for public health). In addition to surface pollutants, rain can also contain
airborne pollutants due to atmospheric deposition (WSDOT, 2006).
In Washington State, The Department of Ecology estimates that 30 percent of all the polluted
water in the state is polluted by stormwater runoff (Department of Ecology, 2003). Less than half
of all salmon and steelhead stocks in Puget Sound are considered healthy due to this pollution and
65 percent of estuaries in the state have temperatures exceeding state water quality standards
(Department of Ecology, 2003). Overall, the Puget Sound Area is highly concerned with impacts
from stormwater runoff (LID, 1999) because of its rapid urban development.
Managing storm water runoff is important to help to reduce these pollution problems that make
all water, hence all related activities, unhealthy in the ecological, hydrological, geological cycles
as well as for all wildlife habitats as well as for public health.
9.2 STORMWATER AND ROADWAYS
Typically, roadways are impervious surfaces covering large areas of land, especially when
considering paved parking lots (see also Chapter 10; Energy & Environmental Control, The
Urban Heat Island Effect).
Runoff from roadways usually contains pollutants due to traffic activities, road construction and
road maintenance. Hydrocarbons (Hc), volatile matters (VM), suspended solids (SS) and heavy
metals are all constituents of pavement runoff (Legret et al, 1996; Sansalone et al, 1996; WSDOT,
2006). Leakage from the materials used in the structure can have impact on the runoff pollution,
however, it is important to remember that most of the pollution from a roadway is not from the
pavement itself, but rather from the activities taking place during usage of the roadway.
46
Leakage of oil and grease are examples of hydrocarbons, and also contributes to phosphorus
pollution and heavy metals. Tire wear is a source of zinc and cadmium (Sansalone et al, 1996;
WSDOT, 2006; Legret & Pagotto, 1999) Break wear is a source of copper, lead, chromium and
manganese (Sansalone et al, 1996; Legret & Pagotto, 1999). Engine wear and fluid leakage is a
source of aluminum, copper, nickel and chromium. Lead comes mainly from the gasoline in the
car, and studies in France has shown the use of unleaded gasoline resulted in a significant
decrease in lead released in the runoff (Legret & Pagotto, 1999). Unlike other organic compounds,
metal elements are not degraded in the environment and are usually washed off the pavement
during the first rain, referred to as the first-flush. (Sansalone et al, 1996).
The impacts of stormwater runoff from state owned rights-of-way vary widely (WSDOT, 2006),
depending on surrounding land use, climate patterns, soil characteristics, receiving water
characteristics, and other local factors. While the runoff discharged from highways and other
transportation infrastructure represents only a portion of the runoff affecting nearby water bodies,
it contributes to the increasing degradation of those waters (WSDOT, 2006). No data is found of
how much of the polluted water in the state is estimated to come from paved roads.
9.2.1
To address storm water management practices, Best Management Practices (BMPs) have been
developed to mitigate the effects of stormwater runoff.
Temporary
BMPs
are
Temporary BMPs are discussed more in Chapter 11; Construction Activities, Temporary Storm
Water Control.
There is a wide variety of design options available as permanent BMPs. Depending on the project
size, the site characteristics, surrounding geological and hydrogeological circumstances,
47
surrounding habitats and nearness to wetlands and water bodies, etc, individual evaluation is
needed to decide on the most feasible option for each project.
In regards to the three key issues described in the overview (reduced infiltration, increased
surface run-off and water pollution) BMPs are often categorized into three major target areas:
Flow control: Balances and lessens the increased rate of discharge caused by
impervious surfaces.
Runoff treatment: Captures and reduces the physical, chemical, and biological
pollutant loads generated primarily from roadway usage.
WSDOTs Highway Runoff Manual (WSDOT, 2006) describes conventional and evaluated
BMPs feasible for control of these functions and provide guidelines of design choice and
considerations.
9.3 BMP OPTIONS
The following overview provides information on the most commonly used runoff treatment
BMPs available for roadway applications as well as present some new emerging techniques.
9.3.1
Source control is mainly related to the activities taking place on the actual roadway such as
choice of deicing technique, dust control, maintenance activities, spills of oil and other toxic
compounds, landscaping management etc. These source control activities are important to address
since removal of the source would reduce the need for pollution treatment. However, these
activities will not be treated in more detail here as this Thesis focuses on the impacts from the
actual permanent structure and not the activities taking place by using it. Temporary source
control for construction activities is dealt with in Chapter 11; Construction Activities.
9.3.2
Runoff treatment BMPs are designed to remove pollutants picked up by the stormwater and
transported with this water. These treatments can be a variety of techniques including
sedimentation, filtration, plant uptake, ion exchange, adsorption, precipitation, and bacterial
48
decomposition (WSDOT, 2006). Some of the techniques to use can provide both runoff treatment
and flow control functions. Table 4 present a summary of BMPs described in the HRM for runoff
treatment.
Table 4. Stormwater runoff treatment BMPs
BMP Type
Infiltration
Dispersion
Biofiltration
Wet Pools
Technique
Bioinfiltration pond
Infiltration Pond
Infiltration Trench
Infiltration Vault
Natural Dispersion
Engineered Dispersion
Vegetated Filter Strip
Biofiltration Swale
Wet Biofiltration Swale
Continuous Inflow
Biofiltration Swale
Ecology Embankment
Wet Pond
Combined Wet/Detention
Pond
Constructed Stormwater
Treatment Wetland
Combined Stormwater
Treatment
Wetland/Detention Pond
WSDOT Reference
HRM Section 5-4.2.1
Features
Treatment and
flow control.
(Can be LID
design)
Treatment and
flow control.
Treatment.
(Can be LID
design)
Treatment
(possible flow
control).
Infiltration BMPs are structures that recharge groundwater by seeping the water through material
such as sand and slowly releasing it back into the environment. Pollution treatment is very
efficient (WSDOT, 2006; UNH, 2005) and achieved by filtering the water and settling of the
sediments and the particles. Conventional infiltration facilities usually need a settling basin and
therefore require larger spaces.
9.3.3
Flow control BMPs are intended to prevent higher stormwater runoff volumes and rapid flow
rates beyond those of natural conditions. The BMPs can be infiltration, dispersion and detention
ponds. Infiltration is the preferred method of flow control according to the HRM. Some of the
techniques to use can provide both runoff treatment and flow control functions. Table 5 presents a
summary of BMPs described in the HRM for flow control.
49
Table 5, Stormwater flow control BMPs
BMP Type
Infiltration
Dispersion
Detention
Technique
Bioinfiltration pond
Infiltration Pond
Infiltration Trench
Infiltration Vault
Drywell
Permeable Pavement
Natural Dispersion
Engineered Dispersion
Detention Ponds
WSDOT Reference
HRM Section 5-4.2.1
Features
Treatment and flow
control
Detention ponds are a frequently used conventional strategy for flow control (WSDOT, 2006).
They are efficient in stormwater treatment (UNH, 2005) but they may be considered inefficient
use of developable land. According to the EPA detention ponds are prone to early siltation and
clogging, create long-term aesthetic problems and can cause insect breeding and weed growth as
well as odor. (EPA, 2006)
9.3.4
Emerging Techniques
There are newer technologies that have been developed to meet urban stormwater control needs.
According to the HRM, Emerging BMPs are Technologies that have not been evaluated using
approved protocols, but for which preliminary data indicate that they may provide a desirable
level of stormwater pollutant removal.
Because no standardized statewide procedure for evaluating these technologies has been available,
local jurisdictions and commercial establishments have had to individually decide on their use.
This has resulted in differences in the standard for accepting new and unproven technologies. As
a result, the Washington State Department of Ecology developed a program for evaluating
unproven technologies. They also approve information and decisions on their use (Department of
Ecology, 2006).
The Stormwater Center at the University of New Hampshire has performed research in
stormwater design methods. During one year, they evaluated 12 stormwater treatments (both
emerging technologies and conventional techniques) for water quality, pollutant removal, flow
reduction, maintenance and materials. Interesting results showed that several Low Impact
Development designs (LID) as well as new manufactured devices were very efficient in pollution
removal and peak flow recharge, whereas traditional approaches did relatively worse (UNH,
50
2005). Note, this result reflect the circumstances under which they were conducted and does not
mean emerging techniques in general are better than conventional.
9.3.5
Low Impact Development design, sometimes called just Low Impact Design, is a category of
stormwater management that focuses on using natural soil, plants and landscaping design to
mimic natural conditions to as large extent as possible.
Research results (UNH, 2005) comparing a variety of BMPs under identical conditions indicate
that LID approaches generally remove the highest levels of contaminants and at the same time
provide flow control. Examples of LID and their hydrolic functions and treatment efficiencies are
listed in Table 5 and Table 6. Some but not all of these techniques are listed as BMPs in the
Highway Runoff Manual and the Stormwater Management Manual for Eastern and Western
Washington (WSDOT, 2006; Department of Ecology, 2005; LID, 1999)
Table 6. LID preferred management practices (PMP) and their hydrologic functions
(LID, 1999)
The ratings High, Moderate, Low, and None stands for the degree of impact in respective
hydrologic function by the named preferred management practice (PMP).
51
Table 7. LID practices and their pollutant removal efficiencies
(LID, 1999)
Compared to conventional BMPs, LID can decrease the use of storm drain piping, inlet structures,
and eliminate or decrease the size of large stormwater ponds. As an example one of the most
common LID designs used (UNH, 2005; LID, 1999) is the bioretention system. This system
removes pollutants, reduce peak flow and peak volumes through infiltration but also by
evapotranspiration. The bioretention system is an example of a practice with many functions.
Figure 11 present an illustration of the functions and Figure 12 present an image of how the
surface landscaping could look like over a bioretention system.
52
The tree and vegetated layer captures the water and provides ecological, hydrologic, and habitat
functions. The storage area provides runoff detention. The organic ground cover provides
pollutant removal and water storage. The planting bed soil provides runoff infiltration, pollutant
removal through groundwater recharge and evapotranspiration through the plant material.
9.3.6
One other alternative to the conventional systems mentioned in Table 4 and Table 5 is to use
manufactured underground detention and infiltration systems. Typically these are used under a
constructed facility such as a parking lot or roadway and do not require additional land. A couple
of commonly used examples (out of many) will be introduced here. One example is the
Underground Detention Unit, see example in Figure 13.
53
It can consist of two units in a series, a water quality unit and a larger detention unit. The water
quality unit is usually made of HDPE (High Density Polyethylene). Stormwater is treated for
sediments and floatables in the HDPE pipes and then flows into the adjacent storage infiltration
unit where a sandy subbase filtrate and treat the water from pollutants. The pollution treatment
rate (over 90%) and the average peak flow reduction rate (over 80%) are found to be very
efficient (UNH, 2005).
There
are
many
proprietary
compact
(EPA, 2007)
flow reduction. These systems are usually made of High Density Polyethylene (HDPE) which
prevents corrosion, are recyclable and makes them lightweight and durable (EPA, 2006).
Currently the Department of Ecology issues this technique as approved for pilot use designation,
which means it is a promising technique but need more verification testing. Field studies are
currently underway for performance and use in Washington State (Department of Ecology, 2006).
Other manufacturered hydrodynamic separators are also available for design to avoid larger
stormwater treatment facilities. Most are only water quality treatment facilities and provide no
flow control. The primary contaminant treated is sediments and oil. One major disadvantage of
these manufactured devices are that they generally require frequent inspections and cleaning
(UNH, 2005), hence higher maintenance costs and efforts.
54
9.3.7
A partial exfiltration trench (PET) is an engineered trench. As shown by the cross-sectional view
in Figure 15, the PET is a hybrid design consisting of a porous pavement surface, a column of
sand working as a filter, and an underdrain (Li et al, 1999; Sansalone et al, 1996). During a
runoff event, surface flow infiltrates the porous pavement and percolates down through the sand
column. Some of the flow exfiltrates to the surrounding soil, and some discharge into the
underdrain. Suspended solids and dissolved metals are treated in the sand column. Also
temporary storage of infiltrated water in the pore space of the sand reduces the peak flow rate.
Hence, the PET serves a dual function: treatment of run-off as well as flow control.
The PET is suited for installation along paved surfaces, such as roads and parking lots, where it
can capture and treat surface runoff. Disadvantages can be the clogging of the porous top
capturing the water, due to dust, particles or possibly even trash along the roadside.
9.3.8
Permeable Pavements
55
may be permeable concrete or permeable asphalt, or manufactured systems such as interlocking
brick for parking spaces and sidewalks.
Permeable Pavements have shown dramatic reductions in surface runoff volumes and peak flow
rates and research indicates that permeable pavements are more efficient than conventional
materials at improving the quality of runoff while maintaining infiltration (Collins et al, 2006;
Brattebo & Booth, 2003; McNally et al, 2007; EPA, 1999; NAPA, 2003).
Permeable pavement may be used on parking areas, roads with light traffic and shoulders
provided that the grades, subsoils, drainage characteristics, and groundwater conditions are
suitable (EPA, 1999).
9.3.8.1 Porous Asphalt Pavements
Porous asphalt pavement is growing in popularity in usage for parking lots and low volume roads
(NAPA, 2003). Porous asphalt pavement consists of an open-graded surface course, a top filter
course, a reservoir course, filter fabric and existing soil or subgrade material. (NAPA, 2003; EPA,
1999). Figure 16 present an overview of a typical pourous asphalt pavement structure.
The following description is based on the National Asphalt Pavement Association (NAPA)
publication Porous Asphalt Pavements, (NAPA, 2003). The porous asphalt course is usually 24 inches thick and has a void space of 16% or more. The open pores in the permeable surface
56
allow water to penetrate through the surface into the filter course and to the reservoir course were
water can be stored like a detention basin. The filter course provides some filtration of particles,
but also serves as protection for the reservoir course during placement of the asphalt mix. The
reservoir course is minimum 8-9 inches thick and consists of uniformly graded crushed stone.
The void space is about 40% which provide stormwater storage as well as passage. Water then
slowly penetrates further through the structure into the soil. This reduces the rate and volume of
discharge while treating the stormwater of pollutants.
9.3.8.2 Advantages and Disadvantages
Water quality in a study (Brattebo & Booth, 2003) performed for long term performance of
permeable pavements (porous asphalt) of a large parking area South of Seattle in WA has found
that water quality was significant better than surface runoff from the conventional asphalt parking
areas. Durability was inspected after 6 years of heavy use of the parking area, and no significant
signs of wear were shown (Brattebo & Booth, 2003). Other studies have given similar results
(Collins et al, 2006; NAPA, 2003; EPA, 1999). The peak flow rate is also found to be reduced
significantly when compared to conventional asphalt pavement runoff. Substantial volume
reductions have been observed in the total amount of water leaving the permeable pavement
sections as runoff and also as exfiltrate in the soil (Collins et al, 2006).
Other advantages are lower pavement noise (Munden, 2006), increased skid resistance (NAPA,
2003; EPA, 1999) and possible cooling of the pavements due to evapotranspiration (See also
Chapter Energy & Environmental Control: Cool Pavements & The Heat Island Effect).
Figure 17 show how rainwater remains
on the surface on a conventional HMA
pavement (right side) compared to a
porous asphalt pavement (left side).
Figure 18 show how water easily
penetrates through the open graded top
course.
57
However, the use of porous pavements is constrained (EPA, 1999; WSDOT, 2006). Generally,
they require deep permeable soils, restricted traffic, and there is also a risk of groundwater
contamination if the system is not used properly. Pollutants that are not easily trapped, adsorbed,
or reduced, may continue to move through the soil profile and into the groundwater (EPA, 1999).
Another disadvantage is that porous pavements need to be maintained to obtain design efficiency
and design life.
One other issue is the clogging of pavement pores by sediments, dust (NAPA, 2003; EPA, 1999)
and ice (in wintertime). University of New Hampshire (UNH, 2005) is currently doing research to
see if less salt can be used in de-icing in a porous parking lot. It appears that much less salt is
needed to treat the porous material, since salt crystals tend to remain on the porous asphalt. On
regular asphalt, salt washes away with the run-off.
The WSDOT HRM currently does not consider porous asphalt pavements as stand-alone runoff
treatment or flow control BMP. However, when used as part of a project surface, it can reduce the
total runoff, thereby providing an overall reduction to the size and placement of other acceptable
runoff treatment and flow control BMPs.
The HRM suggest the use of permeable pavement surfaces to be used at nonpollution-generating
surfaces such as pedestrian/bike paths, raised traffic islands, and sidewalks. Permeable surfaces
58
with a media filtration sublayer (such as sand or an amended soil) could be applied to pollutiongenerating surfaces such as parking lots and low volume roads.
9.3.9
Traffic or road layout can have a very significant influence on the total imperviousness hence
hydrology of a site plan. Data from the National LID Manual (LID, 1999) suggest that the total
impervious surface associated with roads for a particular development can vary from 20,800
linear ft for a typical gridiron layout to 15,300 linear ft for a loops and lollipops layout (Figure
19). According to this data, selection of an alternative road layout can result in a total site
impervious surface reduction of 26 percent. This type of approach is outside the scope of this
thesis as this relates more to Sustainable Alignment (see Chapter 13; Sustainable Alignment), but
should be considered in a future analysis.
59
9.4 POLLUTION PREVENTION OPPORTUNITIES
The variety of BMP available is big and depends on the specific project and its site specific
conditions. In addition to the BMPs described in the HRM and the procedure to choose the most
feasible option, these are some other aspects which could be considered in making decision or
choosing between optimal BMPs. These can be defined in terms of pollution prevention
opportunities such as:
Effective Life
Footprint
Material Usage
Maintenance Needs
Emerging Techniques
Effective life. Design life is important when it comes to sustainability (and also cost). The longer
life of the stormwater structure, the less overall environmental impacts due to less construction
maintenance and operations as well as less material extraction. Table 8 from the HRM present an
overview of effective life of different BMP options. This is not an absolute measure and
evaluation for each specific site should be carried out.
60
Table 8. Overview of effective life for BMPs
(WSDOT Highway Runoff Manual, Table 5.3.1)
Footprint. The less footprint required for a structure, the less impact in habitats and surrounding
natural land.
Conventional stormwater management has focused on large systems and possibly overlooked the
consideration of smaller solutions or facilities placed under the actual pavement structure.
Smaller footprints provide an opportunity to preserve hydrologic, geologic and ecologic functions
of a landscape.
Table 9 presents examples of structures and their design area in relation to catchment area. The
area of a designed device will of course depend on the specific situation, but the intention is to
give and idea of the different footprints needed in comparison to each other. In some cases the
facility is below the pavement surface, in some cases additional footprint is required outside the
limits of the pavement.
61
Table 9. Summary of stormwater strategies and related footprints
(UNH, 2005)
Stormwater Design
Underground
Detention Unit
(Water Quality Unit)
Underground
Infiltration Unit
BMP Type
Manufactured
device
Low Impact
Development
Design
Conventional
Structural
Retention Pond
Bioretention System
Aqua-Swirl and Aqua
Filter
Hydrodynamic
Separator
(sediment removal)
Gravel Wetland
(infiltration and
filtration)
Stone Swale
(Infiltration, limited
filtration)
Manufactured
device
Low Impact
Development
Design
Manufactured
device
Manufactured
device
Low Impact
Development
Design
Conventional
Structural
Catchment Area
1 acre
Peak flow 1 cfs
Treatment Volume 3,264 cf
1 acre
Peak flow 1 cfs
Treatment Volume 3,264 cf
1 acre
Peak flow 1 cfs
Treatment Volume 3,264 cf
1 acre
Peak flow 1 cfs
Treatment Volume 3,264 cf
1 acre
Peak flow 1 cfs
Treatment Volume 3,264 cf
1 acre
Peak flow 1 cfs
1/3 acre
Peak flow 1/3 cfs
Treatment Volume 327 cf
1 acre
Peak flow 1 cfs
Treatment Volume 3,264 cf
2 acre
Peak flow 2 cfs
Area Impacted
5 ft x 20 ft
22 ft x 40 ft
Filter bed 8 ft x 20 ft
Top Width: 31 ft x 41 ft
Overall: 46 ft x 70 ft
(varies)
Total Area: 4,100 sf
Swirl: 4.5 ft Diameter, 8 ft tall
Filter: 6.75 ft Diameter, 12 ft
long
Diameter: 4 ft
Depth: 6.5 ft
Total Area:
5,450 sf
Length: 280 ft
Width: ~10 ft
Material Usage. The less engineered material usage the less extraction of virgin materials and
impacts from production processes. The use of typical engineering materials such as concrete,
steel and plastic require production processes that need materials, energy and release emissions.
By using materials such as native plants, soil and gravel these systems can be more easily
integrated into the landscape and appear to be much more natural. Some considerations:
1. If engineered, the material should consist of recycled content and be recyclable,
see also Chapter: Material & Resources.
2. The embodied energy content of the materials to be used should be evaluated and
compared to conventional systems.
3. The embodied green house gas content should be evaluated and compared.
Embodied energy content and embodied green house gas content are focused life cycle analysis
of all processes that goes into the life of a material, such as all energy or emissions related to
material extraction, material production, transportation and end of life product.
62
Maintenance Needs. The construction with lower maintenance needs that requires less
mechanical equipment should be considered favorable. Maintentance needs vary greatly between
the different design options and can over the life of the system significantly impact the
sustainability measure (as well as cost). Look at the options over the life cycle of the system, the
activities related to these options and define the maintenance needs.
Pollution treatment effectiveness. The construction with the most effective pollution treatment.
As mentioned pollution treatment efficiency varies greatly and the need for treatment at different
sites as well. Treatment could be enhanced treatment a described in Table 3-1, HRM, which
provide additional treatment compared to the basic treatment as described in the HRM (WSDOT,
2006).
Flow control effectiveness. The construction with the most effective flow control function.
As mentioned flow control efficiency varies greatly and the need for flow control at different sites
as well. Perform further research to define this measure.
Emerging Technology. Motivate innovation and design. Use LID techniques that are approved
by the Department of Ecology and the WSDOT, or other emerging techniques. EPA lists
emerging techniques.
63
9.5 REGULATIONS IN WASHINGTON STATE
Stormwater runoff management practices are regulated on the Federal, State as well as on the
Local level.
Federal:
On a Federal level there are several regulations that have to be taken into consideration. The
Clean Water Act
(NPDES) permit or water quality discharge permit for all construction projects. The U.S.
Environmental Protection Agency (EPA) has given the Department of Ecology the authority to
implement these permits in Washington State.
State:
The Department of Ecology has developed Stormwater Manuals for Eastern and Western
Washington and in accordance with this WSDOTs Highway Runoff Manual provides the
regional requirements with listed BMPs.
In the Highway Runoff Manual, Chapter 3, minimum requirements are listed and should always
be met for the specific projects in Washington State. The chapter describes nine minimum
requirements that apply to the planning and design of stormwater management facilities and best
management practices (BMPs) for existing and new Washington State highways, rest areas, parkand-ride lots, ferry terminals, and highway maintenance facilities.
There are different treatment targets listed in the minimum requirements for Runoff Treatment
Control; 1) Basic Treatment, 2) Enhanced Treatment, 3) Oil Control and 4) Phosphorus Control.
Table 10 is taken from the HRM as example.
Local:
Additional more stringent guidelines may apply in local ordinances.
64
Table 10. Runoff treatment targets and applications for roadway projects
(WSDOT,HRM Table 3-1)
65
9.6 CRITERIA DEFINITIONS
The intent with this category is not to compete or modify current stormwater regulations, but
rather to serve as an incentive to choose more sustainable option when given this choice
depending on regulation. The intention is to make decision maker think beyond basic
requirements.
A total of 7 credits can be achieved in this category; Stormwater Management (SM).
Table 11. Credits available in category Stormwater Management
Stormwater Management
Credits
Generally, to get credit in this category, proof must be shown for additional effort in regards to
environmental impacts than the basic requirements.
Minimum requirements in HRM Chapter 3 should be met, and approved BMPs in the HRM are
assumed to meet the basic treatment criteria. If local ordinance is more stringent, it should be
applied.
The process to approve an emerging technology through permitting is complex and requires much
work. Innovation in design is assigned additional credits to provide an incentive for efforts in
development of innovation and new technologies.
A description of the credits with their intent follow.
66
9.6.1
The intent of this credit is to provide an incentive to reduce the impact on natural land and
resources by reducing footprint and material usage and including more sustainable design
practices for storm water management. The objective is to influence projects to consider other
measures beyond basic requirements and cost.
Stormwater Management
2 Credits
Footprint
Material usage
Maintenance needs
In situations where more than one stormwater treatment BMP or combination of BMPs is allowed
to be considered, document a comparison of alternate BMP plans to include this information as a
minimum. The conclusion of the comparison shall include a recommended stormwater treatment
plan based on a review of the comparison and the data presented.
Comments:
Additional research in this credit will be required to decide exactly what kind of documentation to
be submitted. Analysis has to be performed using case studies to decide measurable targets and
possible calculation methodologies. Material usage documentation should submit quantities and
type of materials to be used, as well as data on embodied energy content and embodied green
house gas emissions. This will give an idea of Life Cycle Impacts from the structure.
67
Pollution and Flow Control Efficiencies is to a certain extent handled in Credits SM-2 and SM-4
of this category and can be considered to be taken care of if those credits are also applied for.
68
9.6.2
The intent of this credit is to provide an incentive to increase the runoff treatment rate for higher
water quality in all wetlands, streams, rivers, lakes and for improved habitats and for public
health.
Runoff Treatment
1 Credit
Meet the criteria for enhanced treatment, oil control and phosphorus
control in addition to the minimum requirements as described in the HRM
Chapter 3.
The basic criteria should always be met. Regardless of project site additional treatment effort
should be taken into consideration in the project.
Comments:
The idea and limits in this credit comes from the regulations stated in the WSDOTs HRM.. Note
that these enhanced treatments may not always be practical or useful; if there is no evidence of
phosphorus or oil, obviously the enhanced phosphor or oil control is not necessary. This credit
should be object for future consideration.
LEED-NC v. 2.2, uses corresponding Basic Treatment as stated in the HRM (and the Washington
State Department of Ecologys Stormwater Manuals) as a goal for Credit 6.2: Stormwater
Design: Quality Control. This means BMPs used to treat runoff must be capable of removing
80% of the average annual post development total suspended solids (TSS) load.
80% removal is considered the basic treatment, see WSDOT Highway Runoff Manual Table 3-1,
taking place in all projects with stormwater control and will not be awarded credit in this system.
69
9.6.3
The intent of this credit is to provide an incentive to reduce impervious surface area in order to
decrease stormwater runoff, which can reduce erosion, sedimentation, water pollution and
flooding.
Permeable Area
1 Credit
Example Techniques
Use pervious pavements, vegetated filter strips and other high infiltration techniques. Use porous
pavement for shoulders, bike-lanes, pedestrian walkways and parking lots.
Pervious pavement is defined as:
A permeable surface that readily transmits fluids into the underlying base material. The
pavement may be permeable concrete, permeable asphalt, or manufactured systems such as
interlocking brick or a combination of sand and brick lattice. (WSDOT, HRM, 2006)
Impervious pavement is defined as:
A hard surface area that either prevents or retards the entry of water into the soil mantle as
occurs under natural conditions (prior to development), and from which water runs off at an
increased rate of flow or in increased volumes. Common impervious surfaces include but are not
limited to rooftops, walkways, patios, driveways, parking lots, storage areas, concrete or asphalt
paving, gravel roads, packed earthen materials, and oiled or macadam surfaces. (WSDOT,
HRM, 2006)
70
Comments:
The HRM allows only pervious areas to a certain extent. This is why the % is so low. (20 %
accounts for 6 feet shoulders of a 4 lane 12 ft wide road, as one example). Additional credits
could be given for a higher amount pervious area.
Note that impervious surfaces that need to contain pollutants, such as manufacturing facilities and
specific industries, should not be replaced by a pervious surface at any time.
71
9.6.4
The intent of this credit is to mitigate storm water pollution, peak flow rates and at the same time
minimize the impact and development of natural land, soil and waters.
Permeable Pavement
1 Credit
If the impacted project area has 2,000 ft2 or more of new, replaced, or
new plus replaced impervious surfaces
OR
if the project have land-disturbing activities of 7,000 ft2 or more,
credit is given for the use of permeable pavements for more than 80% of
the new impervious area.
Example technologies:
Use permeable pavements such as porous asphalt pavement, pervious concrete, or other
impervious surface materials.
Comments:
The area requirements for credit application are the minimum requirements as stated in the HRM
for storm water management implementation.
The difference between this credit and credit 4 in this category is the intent of focusing more on
the whole pavement structure rather than just obstacles such as roundabouts, traffic islands,
sidewalks etc. This credit can be assumed to be applicable for parking lots to a large extent.
72
9.6.5
The intent of this credit is to give an incentive to use emerging technologies with higher
sustainable attributes to promote innovation and design in this important category.
2 Credits
If the impacted project area has 2,000 ft2 or more of new, replaced, or
new plus replaced impervious surfaces
OR
if the project have land-disturbing activities of 7,000 ft2 or more, credit is
given for the use of new emerging stormwater technology (as approved
by the Department of Ecology).
Submit reasoning and sufficient proof of reliability of the system, its environmental impacts as
well as reasoning why this is an innovative stormwater technique as well as its sustainable
attributes. Approval for use must be given by the Department of Ecology in Washington State.
Comments:
2 credits are available in this category. This to provide an incentive to the importance of
innovation and design in emerging techniques.
This can require a fair amount of judgment by the owner. The approval function by the
Department of Ecology will reduce the complexity of this judgment and simply enough; if
approved by the Department of Ecology as an emerging BMP, this credit is given.
73
74
Another aspect is to reduce the use of electric energy that is not from a renewable energy source.
One idea for credit requirement is to make sure the lighting system (or a certain part of this) uses
high efficiency luminaries and lamp types (as performance allows) and maximized space between
fixtures as well as uses electricity that comes from renewable energy resource such as hydro,
wind, solar or biomass energy.
2 credits are suggested to be available in this sub-category.
1. Light Pollution Visibility and Night Sky
2. Light Pollution Energy Optimization
10.2 ECO-VIADUCTS
The intent by this credit is to provide access for wildlife and fauna to their otherwise undisturbed
environment that might be separated by the roadway alignment.
Eco-viaducts provides an
ecological corridor beneath
or
over
the
ecological
road.
An
corridor
is
of
local
be
important
in
especially
areas
of
75
This could be applied to highway construction and possible major arterials but are not suitable for
residential roads. Analysis of wildlife and specific species and the impact of the road alignment in
habitats in the area around the roadway have to take place. Analysis have to show that there is a
separation in habitats and that such construction is necessary for the wildlife and fauna considered.
10.3 VISUAL QUALITY (LANDSCAPE & ARCHITECTURE)
The intent with this credit is to improve visual appearance as well as provide more greenery to
reduce impervious areas and promote habitat growth.
Landscaping and architecture is important as sustainable feature as it defines the character of a
space (a region). This has social and economical impacts as it can create appeal for a region and
attractive areas. It can also provide vegetation along the side of the road which will help erosion
and sedimentation control as well as provide opportunities for habitat growth.
1 credit is should be available in sub-category for visual quality in terms of architecture and
landscaping design. This can be for rest-areas, parking lots, medians, and shoulders. Landscaping
should not impair with safety.
This credit might not be easily measured or quantified as it is subjective and highly relates to
traffic behavior and safety. Further analysis and ideas should determine feasibility.
10.4 PEDESTRIAN/BICYCLE ACCESS
From a pavement design perspective bike paths and walkways are important structural
components that have to be available to provide a more pleasant and alive urban environment as
well as provide an option to transportation mode other than car.
Credit could be given if bicycle lanes are included in the design in both directions, and if
pedestrian walkways are available. These design components of course depend on the type of
road, the project size, and the surrounding environment (rural or urban).
1 credit is assumed to be given for Pedestrian and Bicyclist access.
This credit might not be easily measured or quantified and this speaks against having this credit in
the system. Further analysis and ideas should determine feasibility.
76
10.5 COOL PAVEMENTS & THE HEAT ISLAND EFFECT
This category is research in detail as it relates to the pavement structure.
10.5.1 Overview
Temperatures in urban areas can be several degrees higher than surrounding rural areas, a
phenomenon referred to as the urban heat island (UHI) effect. This occurrence is due to the
reduction of natural vegetation, increased human activity and the absorption and radiation of solar
energy in all built surfaces. Roofs, parks, water bodies and pavements all have different
properties deciding how much of the suns heat is absorbed and released, and they all interact
together with other systems in an urban area impacting the total Heat Island Effect. The definition
should not be mixed with global warming when the urban heat island effect is a local temperature
increase, generally the difference between urban and surrounding rural areas. Studies and
simulations performed for 10 large cities in the U.S. indicate an average UHI effect of 2C,
compared to surrounding rural areas (Pomerantz, 2003) and some cities have as much as 10F
(5.6C) warmer than surrounding natural land cover (EPA; 2003). The main impacts of this
temperature increase are:
1. Create additional need of energy use (air conditioning) in dense urban areas.
2. Increase air pollution in urban areas.
3. Contribute to adverse impact of human health and comfort measures (EPA; 2005).
(EPA; 2003)
Pavements are found to be a large contributor to this temperature increase as they in urban areas
stand for a large percentage of surface coverage. Analysis has shown that pavement coverage for
77
travel and parking in large cities in the U.S. counts for 29 to 39 percent of the total land coverage
in the urban area (Akbari et al; 2003), see Table 12. A large portion of this is pavement for
parking. In Houston, Texas, close to 60 % of the transportation land use is used for parking,
where as in Sacramento pavement for parking stand for 29%. Roads still stand for the majority of
pavement coverage ranging from 33% in Houston to 59% in Sacramento (EPA report), see Table
13.
Table 12. Land cover percentages in four urban areas
(Akbari et al; 2003)
Urban Area
Sacramento
Chicago
Salt Lake City
Houston
Pavement
(%)
45
37
36
29
Vegetation
(%)
20
27
33
37
Roofs
(%)
20
25
22
21
Other
(%)
15
11
9
12
Total
(%)
100
100
100
100
Roads
(%)
59
50
48
33
Parking
(%)
29
42
35
60
Sidewalks
(%)
12
8
16
7
Total
(%)
100
100
100
100
10.5.2 Impacts
The air pollution related impacts found at this point are mainly the effect on the production of
photochemical smog, or Ozon (O3 ). Smog is the chemical reaction of sunlight, nitrogen oxides
(NOx) and volatile organic compounds (VOC's) in the atmosphere, which leaves particulate
matter (PM) and ground-level ozone. It is a temperature sensitive reaction, and the production is
increased by increased temperature. The impacts of humans are significant and include breathing
difficulties, headaches, fatigue and can worsen respiratory problems.
For every 1F (0.6C) increase in summertime temperature, peak utility loads in medium and
large cities increase by an estimated 1.5-2.0 % (EPA; 2003).A reduction of 1-2C region average
temperatures can result in a 10% decrease of the peak energy demand, hence lessen annual energy
cost and all impacts related to energy extraction. Field experiments and numerical estimations
suggest that an energy reduction by 30% and an ozone production reduction by 20% can be
78
achieved in large urban areas in the U.S. if all surfaces absorption of the suns heat is decreased.
(Taha et al; Pomerantz, et al; 1999, Rosenberg et al; 1996).
Cool Pavement strategies is one important method to mitigate the effect of heat islands in urban
areas.
79
pavement, and the pavement can use the effect of evaporative cooling.
(EPA; 2005)
80
Most studies mention the effect of heat island mitigations taking place in the top-layer due to
variations in albedo and porosity. However, other studies have shown that a change in albedo
alone may not be the only important factor in determining the pavement surface temperature
through a whole year. Factors such as pavement thickness, heat storage capacity, the materials
thermal conductivity and density are also important considerations (Golden, Kaloush; 2006, EPA,
2005) More research is required in this area to be able to define theses impacts.
Albedos correlate to pavement age (Pomerantz et al; 1999), see Table 14. Cement concrete is
darkened by the presence of iron oxide and dirt. The pavement albedo is approximately 70% of
the aggregate it is made of (Pomerantz et al; 2000). To achieve a pavement albedo of 0.35, an
aggregate albedo of 0.5 should be used. Asphalt concrete tends to get lighter as it ages. As the
asphalt wears off, the aggregate shows, and the albedo of the pavement approaches the albedo of
the aggregates. Also, the asphalt itself becomes lighter due to oxidation.
Table 14. Comparisons of albedo for new and weathered pavement top-layers
(Pomerantz et al, 1999)
Pavement Type
Composition
Asphalt Concrete
7% asphalt + 93%
aggregate by weight
Portland cement/sand/stone
(about 1/3/5 by weight)
White aggregate+cement
which is low in Fe oxides
Thickness
(in)
4
4
4
Albedo
New: 0.05-0.1
Weathered: 0.15-0.2
New: 0.35-0.40
Weathered: 0.25-0.30
New: 0.70-0.80
Weathered: 0.40-0.60
Another factor to take into account is that reflectivity of a paved surface changes over time, due
to shadowing trees, buildings, and also vehicles casting shadows over the pavement. Some of the
reflected light might be reabsorbed by surrounding infrastructure.
Figure 23, presents an overview for different pavements and their corresponding albedo in
Phoenix, Arizona (Golden, Kaloush; 2006). Some of the pavements were tested and compared
when painted with white paint. Computations of surface temperatures of concrete pavement in
Seattle in the summer has been found to have an average temperature of 95F, (35C), whereas in
Tucson Arizona the same type of pavement can be 115F (46C) (Bentz, 2000). Temperatures
presented in Figure 23 represent different meteorological conditions impacting the pavement
temperature compared to various locations in WA, however peak ambient temperatures in the
81
Eastern part of Washington could be assumed to be similar for summer conditions. Discussion of
the different construction techniques to achieve higher albedo or reflectivity is discussed in the
next section.
Figure 23. Surface temperature and albedo for selected types of pavements in Phoenix, Arizona, 2004
(EPA, 2005)
Wind and sea breeze has an effect likely to lessen the effect of increased albedo. Increasing wind
speed lower the surface temperature of the pavement due to convection. In Washington State,
cities in eastern Washington might be more suitable to the use of high albedo pavements than
cities on the coast. Permeability might be less effective cooling mechanism in dry climates than in
wetter climates.
The benefits of cool pavements are not limited to the heat island effect reduction. There are other
properties of a pavement material featuring beneficial attributes in regards to environmental
impacts. These attributes are:
Permeable pavement:
82
The use of permeable pavements reduce the percent of covered land with
impervious pavements, beneficial for stormwater mitigation.
Noise:
o
The open pores of a permeable pavement is shown to reduce tire noise (Sandberg,
2002)
Safety:
o
Illumination:
o
83
10.5.5.2 Concrete Additives
Concrete additives can be used to create lighter pavements.
Slag-cement can be used in place of and in combination with portland cement. The slag cement
will make the concrete lighter and increase reflectivity of the finished surface. The slag cement
also provides other benefits to the pavement in terms of workability and performance. When
substituted for portland cement in quantities between 25% and 65%, slag cement plays a critical
role in reducing permeability in concrete (SCA; 2006). This reduces the ability of evaporative
cooling. In the production of concrete, the use of slag-cement reduced the release of greenhouse
gas emissions and embodied energy content compared to the production of portland cement
concrete, see Figure 4 and 5 (EPA; 2005, SCA; 2006).
Light fly-ash is another option for the use of light aggregate. It reduces the greenhouse gas
emissions and embodied energy compared to the use of portland cement concrete (EPA, 2003,
SCA; 2006), see figure 4 and 5. The drawback is the wide range of colors of fly ash produced
when burning the coal. Fly ash can be tan to dark grey depending on its chemical and mineral
content. Tan and light colors are associated with high lime content. A brownish color is
associated with iron content (FHWA; 2003). Fly ash color is usually very consistent for each
power plant and coal source. Fly-ash in concrete provide benefits such as higher strength,
increased workability, durability and reduced shrinkage. Permeability is however decreased.
Figure 7, 8 an 9 in Chapter Material & Resources describe pollution prevention opportunities for
the reduction of embodied greenhouse gas and embodied energy content in concrete versus slagcement and fly-ash.
10.5.5.3 White Topping and Ultra-Thin White Topping
Thin white topping, TWT, or Ultra-thin white topping, UTW, is a technique to achieve higher
albedo surfaces in rehabilitation of old asphalt pavement (reference EPA, PCA; 2006). UTW
provide the light color and the reflectivity of concrete and is often placed as a 2 to 4 inch thick
layer. The concrete mix is usually fiber reinforced to increase strength. Construction method is
the same as for conventional PCC pavement (NCHRP; 2004), however UTW requires
significantly less time to construct and repairs last much longer (Churilla; 1998). TWT and UTW
are viable alternative for roads of light to moderate traffic, and in some cases applicable for
84
highways and high-traffic city-streets and intersections (NCHRP; 2004, PCA; 2006, Churilla;
1998). Permeability is less than for PCC due to the dense mix with reinforcement, but still in
moderate range (Amos, D; 2001). The pavement has no seasonal weakening. (Rodden, Lange;
2006)
Cost are found to be similar to other pavement strategies (NCHP; 2004), the material is more
expensive, but the strength allows for reduction of dowel bars, hence lessen the total cost. The
construction cost could be expected to be less due to shorter construction time. Over the life of
the pavement, due to the durability and strength, the life cycle cost could be expected to be less
than other overlay techniques.
10.5.5.4 Roller Compacted Concrete Pavement
Roller Compacted Concrete Pavement, RCC, may be used where a strong and durable pavement
is the primary need, and speed and smoothness are not critical. It's placed with conventional or
high-density asphalt paving equipment and then compacted with rollers. RCC is usually used for
larger heavy used pavement areas such as highway weight stations, docks, ports, parking,
intersections and military facilities (PCA; 2006).
RCC provide a hard, durable, and light-colored surface. It has performed well in cold as well as
hot climates. RCC is best used in applications with low speeds and heavy loads, but if it is
smooth enough, it can be used for high speed traffic as well. It is sometimes used as a base layer
topped with HMA, however, this would eliminate the albedo effect. Compared to conventional
concrete RCC it is said to have higher permeability and to be less costly (EPA, PCA; 2006,
Delatte et al, 2003).
10.5.5.5 Light Aggregate in Asphalt Concrete Pavement
The use of light aggregate in Asphalt Concrete Pavements (ACP) is another strategy to acheive
higher reflectance of an asphalt concrete pavement. By volume, aggregate generally accounts for
92 to 96 percent of HMA (WSDOT PGI; 2006), and as mentioned previously, the top course
albedo is 70% of the reflectance of the aggregate it is made of. Limestone is one option for
lighter aggregates, if the material is available locally. In Washington State the use of limestone is
limited. Lighter Granit or Dolomite could be alternatives (USGS; 1998).
85
10.5.5.6 Chip Seals with Light Aggregates
Asphalt chip sealing is an overlay strategy in which a thin layer of asphalt emulsion binder is
applied and immediately covered with a layer of light-colored aggregate. Afterwards, the
aggregate is pressed into the binder using a heavy roller. The result is an exposed aggregate
surface with increased reflectance which is intact as the surface wears. Research has shown that
this technique provide a higher albedo than conventional asphalt concrete overlays, but lower
than conventional PCC pavements (Pomerantz et al; 2003). Another benefit is the exposure of
aggregates improving skid resistance. The technique is usually used on lower volume roads
(AASHTO; 2006), and is found to work well in cold climates as well. If light colored material is
available locally, as discussed, this is a good option for rehabilitation technique.
10.5.5.7 Porous Pavement
The use of porous, or permeable, pavements is possible for both asphalt and concrete structures.
The air void content (AVC) in the structure provide an opportunity for evaporative cooling. This
is feasible in wet climates, however this might not be feasible for winter conditions. Freezing of
the water in the voids might cause the pavement to crack.
The air void content can have a significant effect of the pavement if it is too high or too low.
Findings in Oregon and Washington for example suggest that for every 1-percent drop in AVC
there is a corresponding 10-percent loss of pavement life (NCHRP; 2002). A target range for
HMA to minimize future development of fatigue cracking and rutting was suggested to be 5-6 %
(NCHRP; 2002), at the same time as HMA with high permeability (Open Graded Friction Course)
can have an AVC of 18-22% (ADOT).
Porous pavements are good for other mechanisms such as noise reduction and storm-water
drainage (skid resistance). Durability on high speed, high volume roads depend on climatic
conditions. See also Chapter 9; Stormwater Management and Chapter 10; Energy and
Environmental Control (Quieter pavements).
10.5.5.8 Rubberized Asphalt
Rubberized Asphalt is a broad term describing Hot Mix Asphalt, HMA, containing ground rubber
made from recycling of tires. Pavements in Arizona used for reduction of tirepavement noise
indicate a reduction in surface temperature compared to adjacent PCC (Golden), as opposed to
what is presented in Figure 23. The pavement might have lower albedo, though, the permeability
86
of this kind of pavement can result in evaporative cooling. Ongoing research is investigating this
further.
Research in California and Arizona has shown this to be a durable pavement. However, it has
been found that due to climate as well as the use of studded tires during the winter months has
lead to early failures of this kind of pavement surfaces in Washington State. (Munden, 2006).
87
10.6 QUIETER PAVEMENTS
This category has been research in more detail as it relates to the pavement structure.
10.6.1 Overview
While noise has many different sources, transportation noise is one that has great effects in both
urban and rural areas. Noise is defined as unwanted sound (EPA, 1973). One of the most
significant causes of noise for humans is the annoyance and how this impacts the quality of life.
(This annoyance is related to well known adverse health effects such as increased stress,
disrupted sleep, fatigue, and impact in speech communication.) In addition to the physiological
and emotional responses of transportation noise, it also impacts real estate values hence
contribute to a greater impact of a community; its social and economical status and urban and
rural development.
Sound is part of the science of acoustics, which is a broad and complex field about the generation,
the propagation and the reception of sound. This chapter will not go into details in explaining the
background or the physics behind noise propagation. Terms and definitions will be used with the
assumption that the reader either is familiar with these terms or will find them in references.
It is important to point out however the complexity in analyzing sound and the difference of
sound perception in humans. The response to any sound is a subjective experience and can
depend on age, health, familiarity, time of day, etc, this in addition to the characteristic of the
sound itself. This complexity makes it difficult to easily express and compare sound level
reductions in dB(A)s, which is the unit used to describe transportation noise.
88
Traffic noise generated from vehicles can be further categorized in four major sub-sources
(Bernhard et al, 2005): 1) engine/drivetrain noise, 2) exhaust noise, 3) aerodynamic noise and 4)
tire/pavement interaction noise.
Figure 24. Sound levels related to vehicle speed for noise generated from vehicles
(FHWA, 2005)
Figure 24 present the relation ship between these noise sources and their relation to vehicle speed.
As demonstrated tire noise has a big impact in the overall noise generated. This noise include the
interaction of the tire and the pavement, hence, this is where the relation of pavement surface and
noise generation becomes important.
89
The interaction between the tire and the pavement is causing several mechanisms that create
energy that eventually radiates as sound, or noise. (Sandberg, 2002). These mechanisms depend
to a large extent of the tire, but also on the pavement type and the characteristics of the pavement.
Some of the characteristics of a road surface that can greatly influence noise generation are
(Munden, 2006; Sandberg, 2002): texture of the surface, skewing (orientation of pavement
texture), thickness of the pavement, porosity, tire/road adhesions and elasticity of the pavement
surface. It is also found that age has a significant effect on pavement, both for durability and
noise reduction properties (Munden ,2006).
Quieter pavement is a term that is used to describe pavement types that reduce the tire/pavement
noise generated at tire interaction compared to traditional pavements.
Porous Pavements
o
Porous Concrete
SMA
PCC (limited)
For detailed descriptions of these design options for quieter pavements the reader is referred to
Quieter pavement strategies for Washington State (Munden, 2006). (The cool pavement section
in this Chapter and Chapter Materials & Resources describe general characteristics of some of
these technologies.)
Other advantages found by using porous pavements (other than reducing noise) is less splash and
spray in rainy weather, improved skid resistance, and smoother surface (which can lead to
reduced fuel consumption).
90
Disadvantages are as described the life of the pavement, and the durability of the quieter
properties which is found to be short. Figure 25 present the noise reduction over 6 years for
double layered porous asphalt pavements in Denmark. This is just one example of many that
shows reduced tire/pavement noise reduction over time. A relationship can be seen that
pavements three years and older have higher noise levels than pavements that are two years and
younger (Munden, 2006). This is important to take into account designing for the pavement and
weighting different sustainable features.
Figure 25. Noise reduction of double-layered porous asphalt in Copenhagen over 5 years.
(VTI, 2005).
10.6.4.1 Design Options for Washington State
Several States around the U.S has found successful results to use some of the quieter pavements
techniques. However, early experiments with rubberized asphalt concretes (RAC) and open
graded friction courses (OGFC) to achieve lower noise pavements in Washington State did not
lead to the same results that other states had seen (Munden, 2006). It was found that the States
climate as well as the use of studded tires during the winter months was leading to early failures
of the lower noise pavement surfaces (WSDOT, 2005).
A summary of quieter pavement strategies for Washington State suggest following pavement
types to be used (Munden, 2006):
91
SMAs and double layer porous asphalts have the ability to achieve lower noise levels and
maintain a rut resistant surface.The ability of these pavements to stand up to rutting due
to studded tire wear and prior research on their noise reduction abilities indicate that
SMAs may be well suited for Washington.
Double layer porous asphalts should be considered as an option. While these are still not
as common in the U.S. hopefully information could be gained from Europe and a good
product developement could take place that would be low noise and rut resistant.
Further investigations and analysis are currently taking place in the State for the use of some of
these technologies.
92
known to require large quantities of virgin materials, require large quantities of
energy, see also Chapter: Materials & Resources.
2) usually are large structures that need to be of a specific height and specific
length to reduce the noise significantly, and this only reduces the noise at a
certain distance from the road and the noise wall.
3) are permanent structures that disrupts the environment and significantly reduce
visual quality.
The prevention of noise pollution by impacting the pavement surface characteristics hence is
considered to be the most sustainable way to reduce noise by design.
10.7 REGULATIONS IN WASHINGTON STATE
93
Type II (retrofit)
The implementation of Type II projects are not mandatory from 23 CFR 722, however WSDOT
prioritize retrofit projects (as funding allows) by traffic noise levels, number of benefiting
residences or residential equivalences, cost, and the achievable noise reductions. WSDOTs
requirement is a refinement and extension of the federal highway traffic noise standard 23 CFR
772.
Local more stringent ordinances might apply.
94
10.8 CRITERIA DEFINITIONS
A total of 7 credits can be achieved in this category; Energy & Environmental Control (ECC)
Table 15. Credits available in category Energy & Environmental Control
Energy & Environmental Control (EEC)
Credits
Quieter Pavement
Eco-Viaducts
Pedestrian/bicyclist access
Cool Pavements and Quieter pavements are the credits being studied in more detail. The others
are left for future research and assigned 1 assumed credit each here (however are nonetheless just
as important in the final system).
95
1 Credit
Example Technologies:
Use a light pavement such as PCC, chip-seal with light aggregate, ultra thin white topping or
porous concrete or asphalt pavement.
Comments:
No additional credits are given if higher albedo/higher permeability is used due to the comparison
if credit weighting. This credit is not assumed to be the credit with the highest environmental
impact (weighting) in Washington State. An overview of design option impacts and feasibility is
presented in Appendix C.
The albedo of pavements are measured following ASTM Standard E1918-06. Solar reflectance is
most commonly measured using a solar reflectometer (ASTM C1549) or a pyranometer (ASTM
E1918).
96
Quieter Pavements
1 Credit
Example Technologies:
Use porous asphalt pavements, poro-elastic pavements, rubberized pavements or Open Graded
Friction Course (OGFC).
Comments:
A well known quieter pavement technique can be pavements that are shown to reduce pavement
noise and that has been used and tested to a large extend. Techniques in other parts of the world
should be considered as well.
As some studies have shown that durability of the pavement is shorter with some of these
techniques, this should of course be considered as well since durability is a very important
measure in relation to sustainability. Again, there is a trade of between achieved properties due to
97
design choices and the specific project circumstances need to determine which is the most
desirable effect to pursue.
10.9 DISCUSSION
The criteria for cool- and quieter pavement strategies suggested here are based on current
research performed in the area.
Research in cool pavement area is in an early stage and most research performed in the US is at
this point performed in California and Arizona. Research specific for Washington State needs to
be carried out to define the impacts more precise. At this stage summer months from May to
October is the time when hot surface temperatures in pavements is assumed to cause problems in
Washington urban areas. Future changes in urban growth, population increase and climate change
are drivers to actually give credit for the use of cool pavements at this stage.
The relationship between air temperatures and surface temperature depends on the local climate
and conditions. This should be taken into consideration in evaluating if cool pavements are
feasible alternative. Climate, geography, latitude, peak temperatures and urban form are all
important. Subjectivity is an important factor when it comes to the public reaction and their
perception of lighter pavements as well as quieter pavement. Too light pavement can possibly
give problem of glare, or just the fact of being used to other surfaces. Quieter pavements can be
considered quieter also from the user perspective as reduced roughness and vibrations in the car.
This can add to the overall perception of such pavement. The term lower noise or quieter
pavements needs to be defined.
Other factors affecting performance, cost, and environmental benefits must also be considered
when selecting paving materials. In fact, the best solutions may occur where multiple benefits are
obtained from a paving approach (e.g., porous pavements may help with stormwater runoff, tirepavement noise as well as provide a cooler surface and a smoother surface). Appendix A and C is
intended to give some overview over these preferences. Local materials should always be used if
possible.
98
Site Disturbance
Health of workers
The site disturbance can be further divided into noise, light, water and air emissions pollution. All
equipment and many of the activities such as crushing and grinding of existing pavement generate
noise, release particle emissions and require energy. Working at night or in mornings and evening
causes light pollution in nearby neighborhoods. Stormwater runoff or water used on the site can
pick up construction-related dust and particles and become contaminated if not properly treated.
Construction generates large amounts of waste while simple movement and use of materials can
generate dust and particulate matter. Construction can also impact worker health in regards to
both safety and exposure to emissions and noise.
For this chapter, construction activities is defined as all activities taking place on the actual
construction site. The boundaries of construction activities is set to not include activities such
as extraction, processing, and manufacturing of construction materials (including plant
operations) or end of life activities (such as recycling, landfill or incineration activities).
11.2 PAVEMENT CONSTRUCTION IMPACTS
99
11.2.1.1 Fugitive Dust
Emissions from fugitive dust can be associated with land clearing, demolishing and crushing of
existing pavement, ground excavation, earth moving, and materials loading and unloading. A
large portion of the dust and dirt emissions also results from the equipment traffic over temporary
roads at the construction site. (EPA, 1995).
Dust emissions often vary substantially from day to day, depending on the level of activity, the
specific operations and the weather conditions (Muleski et al, 2005). Construction dust is
classified as Particulate Matter (PM), PM10 and PM2.5, which means particles less than 10 m and
2.5 m in diameter. Research has shown that PM penetrate deeply into the lungs and cause a wide
range of health problems including respiratory illness, asthma, bronchitis and even cancer (EPA,
2004). PM can stay in the air for a long time and it can travel far distances from the actual
construction site.
100
Diesel engines emit a complex mixture of gaseous pollutants and fine particles and are a major
source of air pollution. Particular emissions are nitrogen oxides (NOx), particulate matter (PM),
sulfur oxide gases (SOx), and other toxic air pollutants which contribute to serious adverse health
and environmental effects (EPA, 1995; ICF, 2005).
The emissions from diesel engines are found to include over forty cancer causing substances, and
EPA has concluded that diesel exhaust is likely to be carcinogenic to humans by inhalation at
occupational and environmental levels of exposure (EPA, 2002).
According to EPAs National Emission Inventory (2005 year data) (NEI, 2005), non-road diesel
engines (this including construction equipment only and not other non-road vehicles) are
responsible for 4 percent of NOx emissions nationally (764,000 tons per year), and for one
percent of fine particulate emissions (PM-2.5) (66,000 tons per year) nationally. These
percentages can be considerably higher in some urban areas.
The Washington State Department of Ecology has identified diesel exhaust as the air pollutant
most harmful to public health in Washington State. Seventy percent of the cancer risk from
airborne pollutants is from diesel exhaust, mainly due to the PM
2.5
Until the mid-1990s, emissions from these engines were largely uncontrolled. According to the
Department of Ecology in Washington, construction activities alone are responsible for 18% of
the States PM2.5 emissions (2002 data), see Figure 28.
101
In order to combat the health effects of diesel emissions, the EPA has initiated a program to
reduce diesel engine emissions taking effect in 2007 (EPA, 2004). The plan is estimated to reduce
emissions by more then 90% by 2030. For Washington State the Department of Ecology has a
strategic plan related to this program, see WA Regulations.
11.2.1.3 Fumes From Hot Asphalt
One issue related to the health of workers is the emissions from the asphalt mix or the material
used on site. Asphalt is a complex mixture consisting of paraffinic and aromatic hydrocarbons
and compounds containing sulfur, nitrogen, and oxygen (NIOSH, 1997). Emissions from heated
asphalt are also complex mixtures that include both vapors and fumes (fumes are small particles).
Asphalt fumes have known severe adverse health effects and there are work place recommended
exposure limits of airborne fumes set by the National Institute of Occupational Safety and Health
(NIOSH). The limit is 5mg/m3 which should not be exceeded at any time, and the exposure
should be reduced as much as possible.
102
103
Construction projects involving slopes, exposed and unstabilized soils or other loose materials
can be significant sources of sediment and soil pollution. This can adversely affect drainage
systems on a site as well as receiving waters. Figure 30 shows sediment pollution at a
construction site.
104
noise levels also disturb the natural cycles of animals and impact their habitat adversely (EPA,
1973).
(Note: as defined by this paper, construction activities does not include extraction, processing,
and manufacturing of construction materials)
The consumption of fossil fuels depletes a finite natural resource as well as leads to the
production of greenhouse gases, mainly carbon dioxide (CO2), which contributes to global
warming (Intergovernmental Panel on Climate Change, 2007).
During 2005, approximately 83 percent of total U.S. greenhouse gas emissions consisted of
carbon dioxide (EIA, 2006). Most of this carbon dioxide (98 percent) is emitted as a result of the
combustion of fossil fuels; consequently, carbon dioxide emissions and energy use are highly
correlated. Carbon dioxide emissions in the U.S. have grown by an average of 1.2 percent
annually since 1990 (EIA, 2006).
Energy required for transportation and construction activities can vary tremendously depending
on a wide range of variables including travel distance, equipment type, and the condition of travel
surfaces. Also, more details in the specific equipment being used such as engine type, the load of
material and the average hours of engine usage impact the actual fuel consumption.
105
Not many studies have been performed to quantify the actual use of fossil fuels in construction
related activities, especially for the sub-category of roadway construction. Reasons for this could
be (1) construction vehicles (non-road) have previously not been recognized as important mobile
sources of air pollution, and more focus has been paid to on-road vehicles (cars, trucks and buses)
(Kean et al, 2000), (2) fossil fuel use between construction projects can vary widely depending
upon the actual activity, the equipment fleet, and the location and size of project, and (3)
availability of consistent data is limited.
One award winning study from Europe (IERD, 2002) including 5 countries performed an
assessment of flexible and rigid pavements and the total energy usage for both types of
pavements from initial extraction and manufacture of materials through placement on the
construction site. This study showed that on average 16% of the cost of constructing a road was
energy cost and 12% of this energy was used in the actual construction activities of the pavements
(this only included pavement construction and not material extraction and manufacture).
106
The transport of materials for road construction and maintenance is another major energy issue.
The transportation sector accounted for 33 % of total U.S. energy-related carbon dioxide
emissions in 2005 and out of these (33%) diesel fuel accounted for 22 % (EIA, 2006). This is for
the whole transportation sector, taking all diesel freight trucks into account (Note that this does
not account for construction activities energy and emissions such as paving, demolition, etc., it is
only for transportation).
The cost of transportation both environmentally and economically makes it advisable to use local
materials. LEED, as mentioned previously, encourage local material use as this will reduce the
number and length of vehicle journeys required in construction and maintenance activities as well
as promote local economy. This is included and discussed in Chapter 8; Material & Recourses,
credit Regionally Provided Material, MR-7.
11.3 PAVEMENT CONSTRUCTION ACTIVITIES
The activities in pavement construction differ somewhat depending on the choice of pavement
design. The main activities involved are presented by category and their respective sub-activities.
107
108
Table 16. Rigid pavement construction activities
Construction
Stage
Surface Prep.
Related Activities
Demolition
Excavation
Stabilization
Compaction
Grinding/Milling
Rubblization
HMA Overlay
Equipment &
Material
Excavators
Trucks
Rollers
Grinders
Pavers
Aggregates
HMA
Environmental
Impacts
Fuel Use
Emissions
Dust and
Particles
Waste Material
Noise Pollution
Light Pollution
(Plant
Operation)
Mobile mixer
Transportation
Hauling
aggregates
Hauling PCC
Truck washing
Concrete
mixing truck
End dump
truck,
Bottom dump
truck
Water
Chemicals
Trucks
Cranes
Slipform
paver
Trucks
Slipform
paver
Spreader
Powered
screeds
Fuel Use
Noise
Water Pollution
Water collection
and treatment
Fuel use
Emissions
Noise
Water pollution
(high PH)
Water collection
and treatment
Steel
Placement
Manual
Mechanical
PCC
Placement
Placement of mix
Screeding
Fuel use
Emissions
Noise Pollution
Fuel Use
Emissions
Waste Materials
Water Pollution
Noise Pollution
Fuel use
Emissions
Noise
Fuel use
Emissions
Noise pollution
Waste Material
Consolidation
Vibration
Vibrator
Finishing
Curing
Floating
Texturing
Water Curing
Sealed Curing
Manually
Mechanically
Curing
compound
Water
Plastic
Burlap
Mechanically
Jointing
Saw Cutting
Sealing
Pollution
Prevention
Use low
emitting and
fuel efficient
vehicles.
Reuse
materials
Dust and
erosion control
Noise mitigation
Emissions
filtering
Use low
emitting and
fuel efficient
vehicles.
Manage waste
materials
Dust control
Noise mitigation
Use low
emitting and
fuel efficient
vehicles
Use low
emitting and
fuel efficient
vehicles
Emissions
filtering
Dust control
109
Transportation
Related
Activities
Demolition
Excavation
Stabilization
Compaction
Grinding/Milling
Overlay
Moving
materials
Loading and
dumping
Release agent
use
Equipment
& Material
Excavators
Trucks
Rollers
Grinders
Pavers
Aggregates
HMA
Dump
trucks
Tack trucks
Environmental
Impacts
Fuel Use
Emissions
Dust and
Particles
Waste Material
Noise Pollution
Fuel Use
Emissions
(fugitive)
Waste Materials
Noise Pollution
Water Pollution
Mix Placement
Placement and
Paving activities
Hauling mix
Pavers
Material
Transfer
Vehicles
Trucks
Manual
labor
Fuel use
Emissions
Noise pollution
Compaction
Compaction
Rollers
Manual
compactors
Fuel use
Emissions
Noise pollution
Pollution
Prevention
Use low emitting
and fuel efficient
vehicles
Dust and particle
control
Exhaust filtering
Noise mitigation
Use low emitting
and fuel efficient
vehicles
Exhaust filtering
Dust and particle
control
Noise mitigation
Water collection
and treatment
Use warm mix
asphalt
Low emitting and
fuel efficient
vehicles
Dust and particle
control
Rated pavers
(NIOSH)
Use low emitting
and fuel efficient
vehicles
Dust and particle
control
Noise mitigation
110
11.4 POLLUTION PREVENTION OPPORTUNITIES
There are several pollution prevention opportunities to apply in a construction project, and they
should always be well integrated into the design process. While some of these practices are taking
place as part of construction regulation requirements the suggestions for credits in this category
are intended to provide incentives for additional environmental applications other than what is
already required, and give ideas for extended environmental efforts. In some cases such as
Temporary Stormwater Control and Dust and Particle control the stipulated regulations are
considered being the pollution prevention to aim for due to their complexity and already existing
policy requirements.
Minimize land disturbance and leave maximum vegetation cover, or replant vegetation as
soon as possible.
Apply fine water sprays to control dust from on-site unpaved areas.
Screen the whole site to stop dust spreading, or alternatively, place fine mesh screening
close to the dust source.
Cover piles of building materials like cement, sand and other powders, regularly inspect
for spillages, and locate them where they will not be washed into waterways or drainage
areas.
Wash off all wheel covered with dust and dirt before leaving the construction site.
The use of water to control dust need to be controlled however not to let the polluted water back
into natural waterways without treatment (Temporary Stormwater Control).
111
Table 18. Available options for emission control and related reduced air emissions
(Reference: Diesel Technology Forum 2006, referencing EPA)
112
11.4.2.1 Fuel Trends
The current trend in fuel use is towards cleaner burning fuel and renewable fuel such as ultra low
sulfur diesel (ULSD) and biofuel. ULSD is a diesel product that has eliminated more than 99
percent of the sulfur content. (Diesel Technology Forum, 2006). In a study of fuel sulfur effects,
the Department of Energy (DOE) found that fuel sulfur had significant effects on particulate filter
PM emissions because sulfur actually damages emission-control devices and reduces their
effectiveness (Ecology, 2005). ULSDs primary benefit, then, is the improved effectiveness of
catalysts and emissions filters. (Ecology, 2005). ULSD adoption will then make it possible for
engine manufacturers to use more advanced emission control systems that can achieve higher
reductions in both PM and NOx emissions.
Biodiesel is a renewable fuel that can be manufactured from new and used vegetable oils and
animal fats. Biodiesel in its pure form is known as B100, but it can also be blended with
conventional diesel, most commonly as B5 (5 percent biodiesel and 95 percent diesel) and B20
(20 percent biodiesel and 80 percent diesel) (EPA, 2006). Biodiesel provides significant
greenhouse gas (GHG) emission reductions. B100 reduces lifecycle greenhouse gas emissions by
more than 50 percent, while B20 reduces GHG emissions by at least 10 percent (EPA, 2006). It
also reduces emissions of carbon monoxide (CO), particulate matter (PM), and sulfates, as well as
hydrocarbon and air toxics emissions. However, some studies have demonstrated small NOx
emissions increases up to 10 percent using B100 (ICF, 2005).
As of early 2007, both ULSD and biodiesel are available in Washington State.
113
duty vehicles it is estimated that about 15,000 comes from Construction and Mining (Ecology,
2006). Not all of these 15,000 heavy duty non-road engines are suitable candidates for exhaust
retrofits. According to the Washington Department of Ecology, non-road engines newer than
1996 and 175 hp are potentially suitable candidates for exhaust retrofits. Older engines (1995
and older) are more suitable for replacement (either engine or entire vehicle) rather than exhaust
retrofits (Ecology, 2006).
11.4.2.2 Pace of Change
Although major efforts to reduce diesel emissions are underway, significant impacts may be years
away. Off-road diesel equipment can last 20 to 30 years and typical new emissions standards are
not meant to be met by existing equipment. Therefore, the impacts of such changes are likely to
be felt as a majority of equipment fleets age and are replaced by equipment meeting newer, more
stringent regulations. Furthermore, change and its pace will likely be controlled by the private
sector as they own nearly 90 percent of diesel vehicles and diesel engines (Ecology, 2006).
Efforts to incent the private sector to change ahead of natural equipment turnover rates may help
make diesel emission reductions happen sooner.
11.4.2.3 Cost Considerations
A majority of construction companies are small firms. To retrofit or change their equipment
requires large capital investments, which they may not be able to bear. For many private smaller
construction companies, this cost is significant and is naturally interfering with the environmental
benefits this would achieve. Also the cost of using alternative fuel or low-sulfur fuel is an issue.
EPA estimates the cost of producing 500 ppm fuel to be on average 2.5 cents per gallon, and 15
ppm around 5 cents per gallon. (This takes into account all the necessary changes in both refining
and distribution practices, however this estimated costs vary widely for equipment of different
sizes and for different applications.)
For the vast majority of equipment, the cost of meeting emission standards will be roughly 1-2%
compared with the typical retail price. As an example, EPA estimates that for a 175-hp bulldozer,
it will cost an additional $2,600 to add the advanced emission control systems to the engine and
to design the bulldozer to accommodate the modified engine. A new 175-hp bulldozer costs
approximately $230,000 (EPA information), so the increased costs are about one % of the total
purchase price. In addition, engines running on low-sulfur fuel will have reduced maintenance
114
expenses. (EPA Document 4). Costs could range higher for some types of equipment. As
incentive, there are several grant programs available at local and federal level for companies to
retrofit or change part of their equipment fleet (Ecology, 2006; Diesel Forum, 2006; EPA,
http://www.epa.gov/cleandiesel/).
The benefits to society of reduced health costs are substantial. The California Air Resources
Board has found that every dollar invested in reducing diesel emissions results in three to eight
dollars in savings in improved health, avoided health problems, or lower operating and
maintenance costs for diesel fleets (Ecology, 2006).
Use construction materials that are produced or stockpiled locally to avoid energy use
and pollution generated from transportation activities.
Replace fossil fuel by alternative fuel such as biodiesel (see previous section).
Improve operations (improved logistics to reduce truck queuing and other delays)
While some of the strategies are related to the specific equipment being used, some of the
reduction can be made by controlling the activities in construction productivity and logistic
analysis.
1.
Source Control
Controlling a noise at the source is the most effective method of eliminating construction
noise nuisances and is the easiest to oversee at a construction site.
2. Path Control
115
A physical barrier can destroy some of the sound energy by absorbing the sound and (or)
redirecting the sound away from the receptor. The three strategies for path mitigation are
distance, absorption, and reflection.
3. Receiver Control
This tends to be the most difficult and costly mitigation technique, as the critical receptor
may be humans or precision equipment that is sensitive to low levels of ambient noise
and vibration.
The need of mitigating construction noise depends on the specific project attribute such as
location, size of project, actual activity and working hours. The sensitivity of the environment
varies. Urban environment can be assumed to need more mitigation than a rural environment. A
construction noise analysis in the design phase can find sensitive elements (such as schools,
hospitals, residential buildings, etc) and provide important information of most feasible
mitigation strategy.
116
Use non-toxic paint (pavement markings), solvents and other hazardous materials
wherever possible
Separate, cover and watch toxic substances to prevent spills and possible site
contamination.
Collect any wastewater generated from site activities in settlement tanks, screen,
discharge the clean water, and dispose of remaining sludge according to environmental
regulations (HRM).
Lower plant emissions during production, which benefits the environment and personal
health.
Reduced energy consumption, which lowers fuel use and production costs.
Reduced mixture viscosity, which can improve workability and compaction efficiency
and effectiveness.
Figure 33-36 show some visual comparisons of fumes emitted from HMA versus WMA paving
close to residential buildings (Figure 33 and 34) and at a HMA plant (Figures 35 and 36).
117
Table 19 present a summary of energy and emissions reduction achieved by using different
technologies compared to standard HMA. Note, these numbers represent plant operations and not
construction site operations.
Table 19. Warm mix asphalt technology summary
Recommended
addition rate
Advertised mixing
temperature
reductiona
Plant modifications
WAM Foam
Shell & KoloVeidekke,
Norway
2-part process:
soft asphalt
added first then
hard, foamed
asphalt
78 - 113F (43 63C)
Yes, for foam
Aspha-Min
Eurovia Services
GmbH Germany
Sasobit
Sasol Wax GmbH
Germany
Evotherm
MeadWestvaco,
U.S.
Zeolite (21%
water)
Fischer-Tropsch
(FT) paraffin wax
Emulsion (70%
asphalt) with
additives
0.3% by mix
weight
54F
(30C)
0.8 to 3% by weight
of asphalt binder
32-97F (18-54C)
Yes, to add
material
75 90%
Reduced
30-98%
No information
40 60%
emissionsb
Reduced energy
30 40%
30%
20%
50 75%
consumptionc
a. As compared to a standard of 325F (160C) for HMA. Some references of
documentation/claims are (1,2,3,4,5).
b. Some references of documentation/claims are (6,7,8).
c. Some references of documentation/claims are (7,8,9,10,11,12).
d. Modifications are necessary if Sasobit is to be added to the mixture, modifications are
not necessary if Sasobit is to be added to the asphalt binder beforehand.
118
At present the cost of WMA per ton of mix is greater than the anticipated fuel savings
(Kristjnsdttir et al, 2006). However, as emission standards get more stringent and the cost of
energy change, this ratio is likely to change. The technology is still fairly new and more studies
such as full life cycle impacts should be carried out (Kristjnsdttir et al, 2006), yet the
environmental benefits of using this technique are at this point found to be very good.
One incentive for contractors to use this technology other than cost savings and stringent
emissions regulations can be to give credit for usage in the environmental rating system.
11.5 REGULATIONS IN WASHINGTON STATE
11.5.1 Emissions
EPA regulates emissions from new non-road diesel engines. EPA also sets standards for fuel
composition (ICF, 2005). In June 2004, EPA finalized the Clean Air Non-Road Diesel Rule (EPA,
2006). The rules mandate the use of lower sulfur fuels (ULSD) in diesel engines beginning in
2007, and sets a 500 ppm limit for sulfur in diesel fuel produced for non-road diesel
engines(diesel fuel for non-road engines currently contains about 3,000 ppm sulfur (ICF, 2005)).
Aftertreatment technologies will start phasing into the diesel sector beginning in 2011 for nonroad vehicles with a limit of 15 ppm sulfur (ULSD) for non-road fuel.
These regulations are phased in with emission standards for PM and NOx emissions as well.
These emissions standards are based on engine hp and equipment model year. Table 20 shows
these emissions standards for engines between 25 - 750 hp and the year of standard application.
Table 20. EPA non-road diesel standard
(Reference: Diesel Technology Forum, 2006)
Rated Power
hp< 25
25 hp < 75
75 hp < 175
175 hp < 750
hp 750
PM
(g/hp-hr)*
0.30
0.02
0.01
0.01
0.075
NOx
(g/hp-hr)*
3.5
0.30
0.30
2.6/0.50
Note, however, that most EPA standards apply only to new engines and equipment at the time of
manufacture, and do not affect existing equipment.
119
11.5.1.1 Washington State Department of Ecology Strategy
There is a Diesel Particulate Emission Reduction Strategy for Washington State. The goals
expected under this approach are (Ecology, 2006):
1. Install emission reduction exhaust retrofits on fifty percent of the public legacy diesel
fleet in four years.
2. Install emission reduction exhaust retrofits and add-on fuel efficiency technologies on
fifty percent of the private legacy diesel fleet in eight years.
3. Evaluate, develop and implement an idle reduction program that addresses and
remedies unnecessary idling through on-board retrofits, on-the-ground infrastructure and
anti-idling regulations.
4. Replace twenty-five percent of older (pre-1996 for non-road) legacy vehicles in the
private fleet in eight years.
11.5.2 Stormwater
Construction site stormwater runoff is regulated on the local, State and Federal level.
Most construction projects require a National Pollutant Discharge Elimination System (NPDES)
permit. Some project requires permits under The Endangered Species Act (ESA) (Department of
Ecology, 2005). According to WSDOT, all nonexempt projects must address Construction
Stormwater Pollution Prevention per Standard Specification 1.07.15(1). WSDOTs construction
stormwater pollution prevention planning components consist of Spill Prevention, Control, and
Countermeasures (SPCC) plans and Temporary Erosion and Sediment Control (TESC) plans. All
projects that disturb 7,000 ft2 or more of land, or add 2,000 ft2 or more of new, replaced, or new
plus replaced impervious surface, must prepare a Construction Stormwater Pollution Prevention
Plan (SWPPP). This plan include a TESC plan in addition to an SPCC plan (HRM Chapter 6;
WSDOT, 2006). More stringent local policies may apply.
11.5.3 Noise
WSDOT Environmental Procedure Manual (EPM) Chapter 446 state the Noise policy, however,
this is not specifically related to construction noise, rather noise generated by traffic activities.
120
In most cases, daytime noise from construction activities are exempt from state and local laws
(Email correspondence; Mia Waters, WSDOT). For all other cases, coordination with or permits
from local agencies may be needed.
11.5.4 Energy
WSDOT Environmental Procedure Manual (EPM) Chapter 440 state the Energy policy (partly
with focus on construction activities), in addition to fossil fuel being addressed in Chapter 480
(Irreversible and Irretrievable Commitment of Resources).
The Energy policy reference NEPA/SEPA requirements and FHWA technical guidance. For most
projects, only general construction and operational energy requirements and conservation
potential impacts need to be discussed. WSDOT has no other specific requirements for addressing
energy issues at this time. (WSDOT, 2006).
121
11.6 CREDIT DEFINITIONS
A total of 6 credits can be achieved in this category; Construction Activities (CA).
Table 21. Credits available in category Construction Activities
Construction Activities (CA)
Credits
The construction activities credits are intended to complement and not replace policies and
regulations related to this category. The credits should be used as incentives to think beyond these
policies with the result of additional environmental awareness in construction projects and less
adverse environmental impacts from these activities.
A description of the credits with their intent follow.
122
1 Credit
Fifty percent of the non-road diesel engine fleet should have installed
emission reduction exhaust retrofits and add-on fuel efficiency
technologies complying with the EPA Tier 4 emission standard.
Example Techniques:
Exhaust retrofitting, replace engines, switch to use B-50 or B-100, switch to use ULSD.
Comments:
The credit limitation is based on the Diesel Particulate Emission Reduction Strategy for
Washington State (Department of Ecology, 2006), as described in WA Regulations.
The percentages should, as the implementation of EPAs new regulations as well as technology
manufacturing development in the industry of construction equipment, be increased over time.
123
1 Credit
25 percent of the construction vehicle fleet for the project should use
biodiesel B-50 or B-100.
Example Technologies:
Use biodiesel as a renewable alternative fuel made from vegetable oil such as soybeans,
rapeseeds, sunflower seeds. Use biodiesel that meets ASTM D6751 and is legally registered with
the EPA.
Comments:
Biodiesel is now available in Washington State. The percentage of the vehicle fleet required to
use biodiesel for this credit should, as the implementation of EPAs new regulations take effect,
be increased over time.
124
1 Credit
The two components included in the construction stormwater pollution prevention plan (SWPPP)
are:
1. Temporary Erosion and Sediment Control (TESC) plan.
2. Spill Prevention, Control, and Countermeasures (SPCC) plan.
Example Technologies:
Guidelines for the design of temporary BMPs used during construction are given in WSDOTs
Highway Runoff Manual Appendix 6A, and in Washington Department of Ecologys Stormwater
Management Manual for Eastern and Western Washington.
Comments:
Due to the complexity of impacts from stormwater pollution control and the already existing
stringent regulations, permits approved by WSDOT and the Department of Ecology, or local
ordinance if more stringent, should be equal to the requirements for this credit.
Further research should evaluate this more.
125
1 Credit
This credit accounts for all projects conforming to above description, even if it is exempt such as
day time construction.
The NMP should include:
a description of actions to be used for noise mitigation including source, path or receiver
position mitigation.
if permit is required by State or Local policy, include the permit in the documentation.
Comments:
If construction activities are taking place in rural areas and state or local permits make sure there
is no sensitive or endangered species that can be harmed by the noise activity, this credit will be
given. Nearby neighbourhood needs to be defined as well as how detailed the analysis of
expected sound levels should be. The details of the plan should depend on project size. On idea is
to follow the strategy described in FHWAs Special Report: Highway Construction Noise:
Measurement, Prediction, and Mitigation (Reagan et al).
126
1 Credit
127
1 Credit
Comments:
Environmental benefits of using WMA are found for plant operations. It is assumed that benefits
are of the same nature for on site operations. Further research should be done to better quantify
these benefits.
128
1-3 Credits
Example Technologies
Substantially exceed a rating system credit such as recyclable content or stormwater management.
Apply strategies or measures that demonstrate a comprehensive approach and quantifiable
environment and/or health benefits (LEED-NC v. 2.2).
Comments:
This intent and credit requirement for this credit is benchmarked from LEED-NC v. 2.2, with the
exception of number of credits to earn.
129
The specific requirements for earning of credits need to be outlined in more detail to conform to
consistency in judging. This might be a challenge for this credit.
130
Farmland Preservation
Wetland Conservation
Forest Preservation
These sub-categories are assumed to be given an equal number of credits at this stage to be able
to do a comparison in the final system model..
131
Skanska
Turner
Stantec
King County
This chapter is a summary of personal opinions based on findings from the research interjected
with information from the interviews. The interviews were held in person and presented here is
the writers interpretation of the ideas put forth in the interviews. Appendix D provide a list of
questions being discussed.
14.1 THE IMPACTS OF LEED IN THE BUILDING INDUSTRY
Figure 37 present the intentional and assumed impacts of LEED from the USGBCs perspective.
Is this an accurate picture? The interviews held indicate that this can be the case, but it is too early
to tell. There is a relationship between risk taking, cost and sustainability at this point as some of
the technologies are new and not manifested. But, as the market changes environmental
awareness in sustainability and green design should become common practice.
132
Interview subjects agree that the implementation of LEED has significantly changed the building
industry in the U.S, more so in some parts of the country than others. The awareness of
sustainability and environmental design has increased in the last 5-10 years in construction
projects and LEED has significantly helped to manifest this change on an organizational level,
but also in teams managing construction projects and activities taking place on the actual
construction site (Skanska, Turner, Stantec, 2007). The change can be found in policies as well
(King County, 2007).
133
construction project (Skanska, Turner, 2007); one with significant sustainable understanding and
awareness.
To implement LEED in an organization is working well. As an example King County has
developed its own supplement to LEED to make it work with local policies. In some cases the
local jurisdictions are more stringent, like the energy code and the stormwater regulations. In
other cases, less stringent. How LEED impact the policy development and not the other way
around is not clear at this moment (King County, 2007).
USGBC has an extensive program set up as part of their implementation strategy (USGBC 1,
2006). There is a possibility to take a LEED AP Professional Exam, which includes studies of the
system, its requirements, resources, and processes. As LEED has grown throughout the building
industry, this exam has grown into a marketable benefit for professionals (Turner, Skanska,
Stantec, 2007), a new professional title. USGBC provides lecturers, workshops, and education for
the LEED exam as well as workshops for project managers and companies. At an educational
level, companies or organizations have had to put forth some level of sustainability education
throughout their organization.
The impact of LEED on the actual construction site is also significant. According to interviews
(Turner and Skanska, 2007) LEED requirements are actually making workers interested in
sustainability throughout the construction project hierarchy, and according to (Turner, 2007)
many innovative solutions on the actual construction site is a result from this interest. LEED
requirements have also necessitated additional inspections; many see these inspections going
hand-in-hand with quality and safety control as well since sustainability is really a measure of
quality. Another significant change is the increasing demand for LEED certified buildings by
tenants (the market) as they view LEED buildings can create a healthier and better living and
working environment.
134
While product claims should be reviewed critically (in many cases no specific research in life
cycle impacts has been carried out) the end result is the change this effort creates in building
product marketing. Selling and marketing sustainable products can promote more research in the
field and as the market for such product expands, the prices will likely decrease. This incents
builders to use such products and further vet their claims.
LEED has certainly a marketable value (Turner, Skanska, Stantec, King County, 2007). To
achieve the same market transformation in the roadway industry would be an admirable goal. It
would eventually provide more available options and help make sustainability part of mainstream
design and construction.
135
green design. There is a generation shift were a younger generation of professionals have a
stronger interest in global effects and environmental issues. This could be caused by many factors.
For instance as the effects of global warming are more exposed to everybody through media, the
interest and adaptation/use of such a system is more accepted. The timing for LEED was right.
A rating system for roadway design could at this time ride on the wave of the momentum taking
place for sustainability and green design.
What is not working so well? All interviews mention the documentation as something that has
been time demanding and rather difficult to carry out. This also means higher cost. USGBC
introduced online submittals and support in 2006. This has strongly improved user-friendliness.
14.2 LEED FROM AN ORGANIZATIONAL STANDPOINT
USGBC has a very solid organizational setup with the LEED rating system being their main
product. Focus on its quality, consistency and continuous development is well stated throughout
their overall mission as presented in their foundation documents (Foundation documents; LEED
Policy Manual, LEED Product Development and Maintenance Manual, LEED Committee
Charters).
Figure 38 shows how the LEED committees are organized by product and by technical field. The
Product Committees are divided to address vertical and horizontal markets. Technical Advisory
Groups (TAGs) support both Horizontal and Vertical Market Committees and provide the
consistency of approach and performance that USGBC emphasize in their development of the
LEED systems.
136
The LEED rating systems is the USGBCs main product, but with this follow a selection of other
activities: educational outreach in workshops, the LEED Accredited ProfessionalPM program (the
certification of industry professionals), conferences, research initiatives and case studies.
Partnering with governmental and local jurisdictions and commerce is another marketing effort
and also part of the success. The USGBC has formed effective relationships and priority
programs with key federal agencies, including the U.S. DOE, EPA, NIST, and GSA (USGBC 5,
2002).
137
Certification products are developed and adopted using the following steps (USGBC 2, 2006):
1. Rating Criteria development or review
2. Pilot test of new or revised rating criteria (if necessary)
3. Public comment period on proposed ballot rating criteria
4. Integration of comments into final ballot rating criteria
5. USGBC Membership Ballot
6. Launch of approved product
USGBC policy requires a two-thirds approval of the ballot for a standard to be approved. Many
opportunities for feedback from LEED users are also given in this development process through
meetings, conferences and work shops. (One example is the Future of LEED seminar held in
Seattle in February 2006.)
138
The figure provides a good overview of the importance in working on all these activity levels to
make a market transformation. The same counts for the development of a rating system for
roadway design. Not only technical guidance is important, legislation, education, marketing and
supporting activities needs to be implemented as well.
USGBC has a strong network of 75 regional chapters throughout the U.S. (USGBC 4, 2007). The
chapters provide local green building resources, education and leadership opportunities in green
design, construction and operations for professionals from all sectors of the building industry.
More than 50,000 designers, builders, suppliers and managers have attended USGBC educational
programs (USGBC 4, 2007) to gain practical knowledge and learn about sustainability. This is a
huge educational effort, but promoting significant knowledge and activities in the society on all
levels is a very important part of market transformation and this has shown to be successful.
14.3 DEVELOPMENT AND IMPLEMENTATION OF A RATING SYSTEM FOR ROADWAYS
There are mainly three favorable different scenarios for a rating system for roadway design and
construction to be successfully developed and implemented:
1) Adopted by USGBC and developed as a new LEED system for a new sector of the
construction industry (take a step outside the building sector)
2) Developed individually but incorporated in LEED as part of their LEED for
Neighborhoods (New Reference guide under development, planned to be launched in
2009)
3) Developed and used individually/independently in Washington State and later in other
states.
Benefits of being incorporated in USGBC and their LEED program is the strong marketing value,
the already existing organization, strategic business plan and competence in green building design
and construction. The problem is the vast variety of State and Local requirements and regulations
that need to be met. A nation-wide system applied to roads may have to be too general to provide
much specific guidance. Therefore a State-wide independent system in the regime of USGBC and
their LEED program could be one favorable way to go.
139
To continue the work with this standard strategically there are some important steps that form this
point needs to be taken:
3. Advisory Committee
Form an advisory committee with approval function to make sure regulations are met and updated
references are being used. This should be represented by Federal and State agencies with different
140
environmental and fiscal focus and include local jurisdictions as well. Example of representatives
are: EPA, FHWA, DOE, WSDOT, Department of Ecology, and Counties and Cities. This
committee can serve as over-viewers of the system development. As suggested by USGBC, interagency cooperation will yield a much more integrated policy for a jurisdiction (USGBC, 2002).
A subgroup could include commercial as well as public interests. To include commercial and
public opinions will help in acceptance of such a system once it will be implemented.
4. Perform Case Studies
Verify and test the practice of the system in case studies and do refinement of the categories and
criteria to establish the optimal credit requirement. (This could be an iterative process which will
also continue after the implementation of the system in future system upgrades.)
As suggested by USGBC (USGBC 5, 2002), to build a local momentum and accelerate the
learning curve more quickly, the principles could be included in local and voluntary Pilot Projects.
5. Develop Certification Process
Using the working groups and advisory committee, develop the certification process and define
submittal requirements and process sequence. Define the certification process, parties for
verifications and set up review teams. Make consistency a key-goal.
USGBC and LEED certification has the following simplified certification steps: 1) Project
Registration, 2) Design Submittal, 3) Construction Submittal, 4) Certification reviewing, 5)
Certification Process.
141
At this stage an additional advisory group can be established. Such a group might consist of
private sector construction industry representatives and other stakeholders. Involving these
individuals in the development of a green construction policy, or including them in educational
and outreach programs helps promote future acceptance of these new practices by the local
construction industry (as found by USGBC 5, 2002).
Figure 40 present a simplified overview of how the implementation plan could look like for the
development of an environmental rating system for roadway design and construction.
14.4 DISCUSSION
The roadway construction industry is quite different in the way it works compared to the building
industry. It is a more public industry rather than a more commercial and private one. It is a matter
of where the funding comes from, who pays and what the incentives to use new techniques are.
(Washington funds state transportation spending mostly from the gas tax, and revenues from
licenses, permits, and fees). There is a risk associated with the use of emerging techniques, and
the public sector can be very sensitive taking such a risk when public funds and taxes are used as
funding mechanisms. This can makes it difficult to achieve changes and promote the
implementation of a sustainable roadway rating program.
142
The way the horizontal construction works is that many agencies are involved and the permitting
processes are very complex. How can a rating system work around these complex activities? This
is when advisory groups and technical committees with specialization in respectively field
become very important, and multidisciplinary teams with professionals experienced in these
respective field is vital.
The Green Highway Inititative (www.greenhighways.org) is a new partnership program
developed in 2005 by EPA together with FHWA and other organization such as the American
Concrete Pavement Association (Phone Correspondance, Leif Wathne, Director, ACPA, 2007).
The initial reason for the program was to use EPA as an approval organization and streamline the
process of environmental permitting, allowing and simplifying for the use of emerging BMPs to
mitigate water quality issues related to roadways. The initiative has grown to include other
measures as well. Such an initiative is great and could be very helpful to give some incentives to
use new techniques as well as be part of market transformation. Such a program should be
included in partnering.
There has to be a clear understanding of the standing of the system, that it is a voluntary based
system and that it is not an absolute measure of sustainability. However, included in State and
local policy it can have a greater impacts and become common practice. Changes take time, and
as for all new structures and systems, benefits and most feasible practices might need some time
to show under evaluation. A clear understanding of responsibilities and a strong business and
strategic plan is therefore vital for success in implementation.
143
Sustainable
Alignment
(SA)
Materials &
Resources
(MR)
Stormwater
Management
(SM)
Energy &
Environmental
Control
(EEC)
Construction
Activities
(CA)
Sub-Category3 4
Innovation and
Design Process
(ID)
Total Available Credits
Credit
Available
Total
Available
Credits
1
1
1
1
1
1
1
1
1
1
2
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1-3
3
36
144
LEED-NC has a total of 69 points available within their four categories of certification. Based on
a similar approach for the roadway environmental rating system, Table 23 presents the suggested
levels for certification. Due to the lower number of credits available compared to LEED, three
levels are suggested for the certification of roads.
Table 23. Certification credit requirements
Certification Level
Silver
Gold
Platinum
Range of credits
40-60%
60-80%
80-100%
Number of credits
14-21
22-28
29-36
The work in this thesis provides an overview over suggested areas of environmental concern to be
included in a developed final rating system. The benefits of this kind of rating system for a
roadway construction project can be summarized as:
If an environmental rating system could gain the same success in the roadway construction
industry as it has in the building industry, this would lead to great industry improvement and
market transformation in terms of environmental awareness. It is important to remember that this
system is not an absolute measure of sustainability; there is always trade-offs that needs to be
considered depending on project specifics.
There has to be a clear understanding of the standing of the system, that it is a voluntary based
system rather then a mandatory system. However, if included in State and Local policy it would
reach greater impacts and faster become common practice, which should be the goal.
The development of this system has to be an ongoing process. LEED has proven to be very
successful and it is only a matter of time before such a system will be incorporated for design and
construction of roads. The need for incorporation of sustainable features in roadway design and
construction is large and this is the time to put strong movement into development of this kind of
system.
145
15.2 RECOMMENDATIONS
The next step is to continue the work with development of this system. Following bullet points
summarize the most important recommendations with some comments:
Research and development should be continued for the credits left for future research in
this thesis as well as development of the ones suggested here. Each credit is a great
opportunity for further studies in different areas of specialization. Use university research
competence and industry knowledge by forming working groups as suggested in Chapter
14; Implementation Strategy & Impacts.
Case studies should evaluate the credit limitations and optimize the requirements for all
credits. The case studies should evaluate different type of construction projects with
various sizes and budgets.
Perform weighting of the credits. The threshold levels in LEED are criticized for not
being industry appropriate and the threshold levels suggested may not sufficiently be
above the norm to be called green. Future research would benefit from doing Life
Cycle Analysis for each credit. This would be the best way to weight the credits based on
their environmental performance.
146
LIST OF REFERENCES
AASHTO American Association of State Highway and Transportation Officials, NCHRP 2525(04) Final Report Environmental Stewardship Practices, Procedures , and Policies for
Highway Construction and Maintenance v1.0, Accessed November 2006
AASHTO, Center for Environmental Excellence, Designing for Environmental Stewardship in
Construction & Maintenance, Chapter 3.15, 2006,
http://environment.transportation.org/environmental_issues/
ACA & ACAA, American Coal Council & American Coal Ash Association, Coal Ash Fact
Sheet, Available from www.acaa-usa.org, Accessed in November 2006
Amirkhanian, S.N., Vaughan, K.M., Field Evaluation of use of waste shingles in asphalt
mixtures, Clemson University, South Carolina Department of Transportation, Federal Highway
Administration, Report Number: FHWA-SC-01-04, 2001
Amirkhanian, S.N., Utilization of Crumb Rubber in Asphalt Concrete Mixtures South Carolinas
Experience, Clemson University, South Carolina Department of Transportation, Federal
Highway Administration, July 2001
Amos, D., Evaluation of Ultra Thin White Topping, Missouri Department of Transportation,
Research Investigation RI99-012, 2001
Arika, C.,Canelon, D.J., Nieber, J.L., Impact of Alternative Storm Water Management
Approaches on Highway Infrastructure: Guide for Selection of Best Management Practices
Volume 1, Minnesota Department of Transportation, February 2006
Bentz, D.P., A Computer Model to Predict the Surface Temperature and Time-of-Wetness of
Concrete Pavements and Bridge Decks, U.S Department of Commerce, National Institute of
Standards and Technology, NISTIR 6551, August 2000
Bernhard, R.J., Wayson, R.,L., An introduction to tire/pavement noise, Department of Civil &
Environmental Engineering, University of Central Florida, SQDH 2005-1, January 2005
Brattebo, B. O., Booth, D. B., Long term stormwater quantity and quality performance of
permeable pavement systems, Water Research. Vol. 37, no. 18, pp. 4369-4376. November 2003
147
Carpenter, A.C., Garnder, K.H., Fopiano, J., Benson, C.H., Edil, T.B., "Life Cycle Based Risk
Assessment of Recycled Maerials in Roadway Construction", WASCON 2006, Sixth
International Conference on the Environmental and Technical Implications of Construction with
Alternative Materials Science and Engineering of Recycling for Environmental Protection,
Belgrade, Serbia & Montenegro, May 30- June 2, 2006, edited by M. Ilic, J. Goumans, S. Miletic,
J Heynen & J. Senden and the Techonology Transfer Promotion ISCOWA (TTPI) Foundation (pp
229-240), 2006
CIWMB, California Integrated Waste Management Board, Asphalt roofing shingles in asphalt
pavements, Accessed online in December 2006,
http://www.ciwmb.ca.gov/ConDemo/Shingles/Pavement.htm
Churilla, J.C., Ultra-Thin white Topping, FHWA, Public Roads: Vol. 62, No.2,
September/October 1998
http://www.tfhrc.gov/pubrds/septoct98/ultra.htm
Collins, K.A., Hunt, W.F., Hathaway, J.M., Evaluation of various types of permeable pavements
with respect to water quality improvement and flood control, 8th International Conference on
Concrete Block Paving, November 6-8, San Francisco, California USA, 2006
CRSI, Concrete Reinforcing Steel Institute, Special Report Steel Reinforcing bars: Recycled
and Recyclable, Available from CRSI, 2002
Decker, D., Evaluating uses of recycled material in HMA, The National Asphalt Pavement
Association, Hot Mix Asphalt Technology, Vol. 12, No. 1., 2007
Delatte, N., Amer, N., Storey, C., Improved Management of RCC Pavement Technologies,
Department of Civil & Environmental Engineering, University Transportation Center for
Alabama, The University of Alabama at Birmingham, Alabama, UTCA Report 01231, January
2003
Diesel Technology Forum, Retrofitting Americas Diesel Engines A Guide to Cleaner Air
Through Cleaner Diesel, Diesel Technology Forum, Brochure, 2006
Ecology, Diesel Particulate Emission Reduction Strategy for Washington State, Washington
State Department of Ecology Air Quality Program, December 2006
Ecology, Assessment of Potential Strategies to Reduce Emissions from Diesel Engines in
Washington State, Washington State Department of Ecology , December, 2003
148
EIA, Emissions of Greenhouse Gases in the United States 2005, Report #: DOE/EIA0573(2005), Energy Information Administration, November 2006, Available online at
http://www.eia.doe.gov/oiaf/1605/ggrpt/index.html
Eighmy, T.T., Magee, J. B., The road to reuse, Civil Engineering; Sep 2001; 71, 9;
ABI/INFORM Global pg 66.
AASHTO, Standard Specification for Reclaimed Concrete Aggregate for Unbound SoilAggregate Base Course, AASHTO M 319-02, 2006
EPA, Storm Water Technology Fact Sheet Porous Pavement, United States
Environmental Protection Agency, Office of Water, Washington, D.C., EPA 832-F-99-023,
September 1999
EPA, Storm Water Virtual Trade Show Technologies, Stormwater, Accessed Online in
February 2007 at http://www.epa.gov/NE/assistance/ceitts/stormwater/techs.html
EPA, U.S. Inventory of Greenhouse Gas Emissions and Sinks 1990-2000, Environmental
Protection Agency: Washington D.C., EPA 430-R-02-003, 2002
EPA, Characterization of building related construction and demolition debris in the United
States, The U.S. Environmental Protection Agency Municipal and Industrial Solid Waste
Division, Report No. EPA530-R-98-010, June 1998
EPA, Cooling Summertime Temperatures- Strategies to Reduce Urban Heat Islands,
Environmental Protection Agency, September 2003
EPA, Cool Pavement Report EPA Cool Pavements Study- Task 5, Prepared for Heat Island
Reduction Initiative, U.S Environmental Protection Agency, June 2005
EPA, Compilation of Air Pollutant Emission Factors, Volume 1: Stationary Point and Area
Sources, Chapter 13.2.3-Heavy Construction Operations, AP 42, Fifth Edition, 1995
EPA, Clean Air Nonroad Diesel Rule, Regulatory Announcement, Office of Transportation and
Air quality, EPA420-F-04-032, May 2004
EPA, Latest Findings on National Air Quality 2002 Status and Trends, EPA 454/ K-03-001,
August 2003 , Accessed in February 2007 at
http://www.epa.gov/air/airtrends/aqtrnd02/2002_airtrends_final.pdf
149
EPA, Reducing Air Pollution from Nonroad Engines, Program Update, Office of
Transportation and Air quality , EPA420-F-03-011, April 2003
EPA ,Health Assessment Document for Diesel Engine Exhaust, National Center for
Environmental Assessment, Office of Research and Development, U.S. Environmental Protection
Agency, Washington, D.C, 2002
EPA, Alternative Fuels: biodiesel, Office of Transportation and Air quality, EPA420-F-06-044,
October 2006
EPA, Direct Final Rule and Notice of Proposed Rulemaking for Amendments to the Nonroad
and Highway Diesel Fuel Regulations, Regulatory Announcement, EPA420-F-06-033, April
2006
EPA, Public Health and Welfare Criteria for Noise, Prepared by The Office of Noise Abatement
and Control, July, 1973. Accessed online in February at
http://nonoise.org/epa/roll1/roll1doc3blp4.pdf.
EPRI, Electric Power Research Institute, Concrete Applications of Coal Ash Highway
Structures and Pavements, Resource Paper No. 1004696, September 2002
Ewell, M.,. Mining and Quarrying Trends, USGS Minerals Yearbook 2004, U.S. Geological
Survey, Retrieved February 2007 from
http://minerals.usgs.gov/minerals/pubs/commodity/m&q/index.html.
FHWA, Highway Statistics 2005, The Federal Highway Administration, retrieved online in
February 2007 at
http://www.fhwa.dot.gov/policy/ohpi/hss/index.htm
FHWA, Federal Highway Administration, Transportation applications of Recycled Concrete
Aggregates, FHWA State of the Practice National Review, September 2004
FHWA, Federal Highway Administration, User Guidelines for Waste and By-product Materials
in Pavement Construction, FHWA-RD-97-148, 1997, Accessed Online November 2006
http://www.fhwa.dot.gov/Pavement/pub_details.cfm?id=384
150
FHWA, Federal Highway Administration, Fly Ash Facts for Highway Engineers, Report No.
FHWA-IF-03-019, June 2003
FHWA, Federal Highway Administration, Foundry Sand Fact for Civil Engineers, Report No.
FHWA-IF-04-004, May 2004
FHWA, Federal Highway Administration, The Roadmap to Quiet Highways, Results of the
FHWA Workshop September 14-16 2004, Retreived in workshop (Tire-Pavement Noise 101),
November 2005.
FHWA, Tire-Pavement Noise Home Page, U.S Department of Transportation Federal Highway
Administration, Accessed online in February 2007 at
http://www.fhwa.dot.gov/environment/noise/tp_noise.htm
Gilchrist, A., Allouche, E.N., Cowan, D., Prediction and mitigation of construction noise in an
urban environment , Canadian Journal of Civil Engineering, Vol. 30, no. 4, pp. 659-672, 2003
Golden, J.S., Kaloush, K.E., Mesoscale and microscale evaluation of surface pavement impacts
on the urban heat island effects, The International Journal of Pavement Engineering, Vol. 7, NO.
1, March 2006
Golden, J.S., A Sustainable Systems Approach To The Hysteresis Lag Effect Of Surface
Materials & Urban Heat Islands, Arizona State University, Tempe, Arizona
Hicks, R.G., Lundy, J.R., Leahy, R.B., Hanson, D., and Epps, J., (1995). Crumb Rubber
Modifier in Asphalt Pavement Summary of Practice in Arizona, California and Florida. Report
Nr. FHWA-SA-95-056-Federal Highway Administration, 1995
Horvath, A., Life-Cycle Environmental and Economic Assessment of Using Recycled Materials
for Asphalt Pavements, University of California, Berklely, 2003
ICF Consulting, Emission Reduction Incentives for Off-Road Diesel Equipment Used in the Port
and Construction Sectors, Prepared for EPA, May 2005, available at
http://www.epa.gov/sectors/pdf/emission_20050519.pdf
IDOT, Illinois Department of Transportation, Utilization of Recycled
Materials in Illinois Highway Construction, Carolyn T. Griffiths, James M. Krstulovich, Jr.,
Physical Research Report No. 142, May 2002
151
IERD, Integration of the Measurement of Energy Usage into Road Design, Final Report of the
EU SAVE Programme, Commission of the European Communities Directorate-General For
Energy and Transport, Final Report, No: 4.1031/Z/02-091/2002, 2002
Intergovernmental Panel on Climate Change, ICCP, Climate change 2007: The Physical Science
Basis, Summary for Policymakers, Contribution of Working Group I to the Fourth Assessment
Report of the Intergovernmental Panel on Climate Change, Paris, February 2007, Retrieved
Online in February 2007 at http://www.ipcc.ch/SPM2feb07.pdf
ISO 14021, International Standards Organization, Environmental labels and declarations Selfdeclared environmental claims, (type II environmental labeling), ISO, 1999
Kean, A.J., Sawyer, R.F., Harley, R.A., A Fuel-Based Assessment of Off-Road Diesel Engine
Emissions, Journal of the Air & Waste Management Association, Vol. 50, November 2000
King County, Ordinance #15118 Adopted by King County Council February 7, 2005
Accessed Online in February 2007,
http://www.metrokc.gov/dnrp/swd/about/green-building-team/documents/Ordinance_15118.pdf
King County, Interview: King County, Katie Spataro, Project Manager, Personal Interview,
Seattle, February 2007
Kristjnsdttir, Muench, Michael, Burke, Assessing the Potential for Warm Mix Asphalt
Technology Adoption , Paper, July 2006
Legret, M., Colandini, V., Le Marc, C., Effects of porous pavement with reservoir structure on
the quality of runoff water and soil, The Science of the Total Environment, Vol. 189/190, pp.
335-340, 1996
Legret, M., Pagotto, C., Evaluation of pollutant loadings in the runoff waters from a major rural
highway, Science of the Total Environment. Vol. 235, no. 1-3, pp. 143-150. September 1999
Legret, M., Odieb, L., Demarea, D., Julliena, A., Leaching of heavy metals and polycyclic
aromatic hydrocarbons from reclaimed asphalt pavement, Water Research. Vol. 39, no. 15, pp.
3675-3685. Sept. 2005
Li, Y., Buchberger, S.G., Sanasalone, J.J., Variably saturated flow in storm-water partial
exfiltration trench, Journal of Environmental Engineering, Vol. 125, no. 6, pp. 556-565. June
1999
152
LID, Prince Georges County, Low-Impact Development Design StrategiesAn Integrated Design Approach, Prince Georges County, Department of Environmental
Resources Programs and Planning Division, Maryland, June 1999
Malhotra, V.M., Making Concrete Greener With Fly-Ash, Concrete International, May 1999
McNally, C., DeProspo Philo, L., Boving, T., Porous Pavement and Groundwater Quality
Technical Bulletin, The University of Rhode Island Cooperative Extension in partnership with
the Rhode Island Department of Health Source Water Protection Program, Accessed Online in
January 2007 at http://www.uri.edu/ce/wq/NEMO/Publications/PDFs/PP.GWQuality.pdf
Munden, H.,Lower Noise Pavement Options For Washington State, Master Thesis, Department
of Civil & Environmental Engineering, University of Washington, 2006
Muleski, G.E., Cowherd, C.,Jr., Kinsey, J.S., Particulate Emissions from Construction
Activities, Journal of the Air & Waste Management Association. Vol. 55, no. 6, June 2005
NAPA, National Asphalt Paving Association, Reclaimed Asphalt Pavement (RAP): Stockpile
Emissions and Leachate, Special Report SR-190, Version 3.23.06, 2006, Accessed online at
www.hotmix.org, December 2006
NAPA, Porous Asphalt Pavements, Information Series 131, National Asphalt Pavement
Association, 2003
NCHRP-Synthesis 338, Thin and Ultra Thin White Topping, A Synthesis of Highway Practice,
NCHRP-Synthesis 338 and Transportation Research Board, Washington DC, 2004
NCHRP, Significance of As-constructed HMA Air Voids to Pavement Performance from an
Analysis of LTPP Data, Research Result Digest , No. 269, September 2002
NEI, National Emissions Inventory, Air Pollutant Trends Data, Average annual emissions 19782002, all criteria pollutants,
http://www.epa.gov/ttn/chief/trends/index.html#tables
NIOSH, Engineering Control Guidelines for Hot Mix Asphalt Pavers-Part 1 New Highway
Class Pavers, National Institute for Occupational Safety and Health, Publication No. 97105
1997
153
Norrman, J., Rosn, L., Norin, M., Decision Analysis for Storage for Reclaimed Asphalt,
Environmental Engineering Science, Vol. 22, No. 6, 2005
OSHA, Suter, A.H., Comments on Occupational Noise to the OSHA Standards Planning
Committee, Docket No. C-04, November 28, 1994 available online at
http://nonoise.org/library/osha/osha.htm
PCA, Portland Cement Association, Pavements-City Streets, Web-page
http://www.cement.org/pavements/pv_cp_citystreets.asp
PCA, Portland Cement Association, Roller Compacted Concrete, Web-page
http://www.cement.org/pavements/pv_rcc.asp
PGI, 2003, Muench, S., Mahoney, J., Pierce, L. WSDOT Pavement Guide Interactive . June 19,
2006. https://guides.ce.washington.edu/uw/wsdot/ . Washington State Department of
Transportation. 2006.
Pomerantz, M., Akbari, H., Chen, A., Taha, H., Rosenfeld, A.H., Paving Materials for Heat
Island Mitigation, Lawrence Berkely National Laboratory, LBNL-38074,1997
Pomerantz, M., B. Pon, H. Akbari, S.C. Chang, The Effect of Pavements Temperatures on Air
Temperatures in Large Cities, Lawrence Berkeley National Laboratory, LBL-43442, April 2000
Pomerantz, M., Akbari, H., Chang, S.-C., Levinson, R., Pon, B., Examples of cooler reflective
streets for urban Heat-Island Mitigation: Portland Cement Concrete and Chip-Seals, Lawrence
Berkely National Laboratory, LBNL-49283, 2003
Reagan, J.A., Grant, C.A., Special Report: Highway Construction Noise: Measurement,
Prediction and Mitigation, Prepared by: US. Department of Transportation, Federal Highway
Administration,
Office
of
Environmental
Policy,
Retrieved
at
http://www.fhwa.dot.gov/environment/noise/highway/index.htm, February 2007
RMRC, Recycled Materials Resource Center, Standard Specifications for Reclaimed Concrete
Aggregate for Use as Coarse Aggregate in Portland Cement Concrete, University of Hampshire,
Retrieved online in November 2006
http://www.rmrc.unh.edu/resources/specifications/rmrcspecs.asp
154
RMRC, Recycled Materials Resource Center, Apul, S.D., Gardner, K., Eighmy, T., Benoit, J.,
Brannaka, L., A Review of Water Movement in the Highway Environment, Implications for
Recycled Materials Use, University of New Hampshire, February 2002
RMRC, Recycled Materials Resource Center, White Paper and Specification for Glass Cullet
Use for Soil Aggregate Base Course, University of New Hampshire , June 2000, Accessed
online November 2006
http://www.rmrc.unh.edu/Research/Rprojects/Project13/Specs/docs/glassculletspec.PDF
RMRC, Recycled Materials Resource Center, Draft White Paper for Recycled Asphalt Shingles
as an additive in Hot Mix Asphalt, University of New Hampshire , April 2003, Accessed online
January 2007
http://www.rmrc.unh.edu/Research/Rprojects/Project13/Specs/RASAC/drftwhite41503.pdf
Rosenfeld, A.H., Romm, J.J., Akbari, H., Pomerantz, M., Taha, H., Policies to Reduce Heat
Islands: Magnitutes of Benefits and Incentives to Achieve Them, Lawrence Berkely National
Laboratory, LBL-38679,1996
Rodden, R.A., Lange, D.A., An overview of Ultra-Thin Whitetopping Technology,
TECHNICAL NOTE No.21, University of Illinois, Dept of Civil & Environmental Engineering,
2006
Sacket, J, LEED Version 3.0: Foundation for the Future, USBGC News, September 2006,
Accessed online in February at
http://www.usgbc.org/News/USGBCNewsDetails.aspx?ID=2607
Sandberg, U., Ejsmont, J. A., Tyre/Road Noise Reference Book, Informex, Poland, 2002.
Sansalone, J.J, Buchberger, S.G., Al-Abed, S.R., Fractionation of heavy metals in pavement
runoff, The Science of the Total Environment, Vol. 189-190, pp. 371-378, 1996
SCA, Slag Cement Association, Tools for Exploring Slag Cement in Concrete, CD Version
2.01, 2005, Available from Slag Cement Association, 2005
SCA, Slag Cement Association, Reducing Permeability, Slag Cement in Concrete, No. 6, Website document, 2006
http://www.slagcement.org
155
Simon, M.J., Chesner W.H., Eighmy, T.T., Jongedyk, H., National Research Projects on
Recycling in Highway Construction, article sponsored by the Federal Highway Administration
(FHWA) and the National Cooperative Highway Research Program (NCHRP), Accessed online
in November 2006 at http://www.p2pays.org/ref/12/11105/
Skanska, Interview:, Skanska USA Building Inc., Tony Stewart, Vice President, Personal
Interview, Seattle, February 2007
SRA, The Swedish Road Administration (Vgverket) Handbok fr tervinning av asfalt
(Reference Guide for Reclaimed Asphalt Pavement), ISSN 1401 9612, Publication 2004:91,
2004
SRI, Steel Recycling Institute, Steel Takes LEED with Recycled Content & Steel Recycling
Rate at a Glance, Available from the Steel Recycling Institute, June 2006
SRI, Steel Recycling Institute, 2005 The Inherent Recycled Content of Todays Steel,
Available from the Steel Recycling Institute, April 2006
Stantec, Interview:, Stantec Consulting Inc., Tom Marseille, Principal, Personal Interview,
Seattle, February 2007
The Department of Ecology, Stormwater Management Manual for Western Washington, Volume
II, Construction Stormwater Pollution Prevention, 2005
Townsend, T. G., Brantley, A., Leaching Characteristics of
Asphalt Road Waste, University of Florida, Report #98-2, June 1998
Turner, Interview: Turner Construction, Craig Vierling, Project Manager, Personal Interview,
Seattle, February 2007
UNH, 2005 Data Report, University of New Hampshire Stormwater Center, Accessed in
January 2007, Available Online at
http://ciceet.unh.edu/news/releases/stormwater_report_05/Stormwater_05-03-06.pdf
USDOT/FHWA, Crumb Rubber Modifiers in Asphalt Pavements, FP 25, December 31 1995,
Accessed Online in December 2006, http://www.asphaltrubber.org/library/fp25_ch3.asp
156
USGBC, LEED For New Construction Version 2.2, LEED-NC, Green Building Rating System
for New Construction and Major Renovations, October 2005
Accessed Online November 2006,
https://www.usgbc.org/FileHandling/show_general_file.asp?DocumentID=1095
USGBC, LEED Registered Projects, U.S, Green Building Council, Retrieved online in
February 2007, at https://www.usgbc.org/ShowFile.aspx?DocumentID=2314, 2007
USGBC 1, LEED Policy Manual, Part of the Foundation Documents of the Leadership in
Energy and Environmental Design Environmental Rating System, A Tool for Market
Transformation, LEED Steering Committee, August 2006, Available online at
http://www.usgbc.org/
USGBC 2, LEED Product Development and Maintenance Manual, Part of the Foundation
Documents of the Leadership in Energy and Environmental Design Environmental Rating
System, A Tool for Market Transformation, LEED Steering Committee, August 2006, Available
online at http://www.usgbc.org/
USGBC 3, LEED Committee Charters, Part of the Foundation Documents of the Leadership in
Energy and Environmental Design Environmental Rating System, A Tool for Market
Transformation, LEED Steering Committee, August 2006, Available online at
http://www.usgbc.org/
USGBC 4, What we do, Information accessed online in February 2007,
http://www.usgbc.org/DisplayPage.aspx?CMSPageID=1498&
USGBC 5, State and Local Tool Kit, U.S. Green Building Council, Washington DC, November
2002, Available from the USGBC.
USGC, Material in Use in U.S. Interstate Highways, U.S Department of Interior, U.S.
Geological Survey, Fact Sheet 2206-3127, October 2006
USGS, U.S. Geological Survey, The Mineral Industry of Washington, Memorandum of
Understanding between USGS, Washington State Department of Natural Resources, Division of
Geology and Earth Resources, Washington, 1998
VTI, Low-Noise Road Surfaces- State-of-the-Art, By Adj Prof Ulf Sandberg
Swedish Road and Transport Research Institute (VTI), EU project SILVIA International Seminar,
23 August 2005 Brussels, Belgium, Retreived online in February 2007
157
VTI, Vgytans inverkan p trafikbulleremissionen korrektionstabell fr
effektsambandsmodeller, U. Sandberg, Vg och Transportforskningsinstitutet, VTI 30-2000,
Vgverket, Sweden, 2000
Washington State Department of Ecology, Lets protect our streams and salmon today or they
could be history tomorrow, Fact Sheet, July 2003, Available from the Department of Ecology,
Washington
Washington State Department of Ecology, General use level designation for pretreatment (TSS)
For AquaShieldTM, Inc.s Aqua-Swirl Concentrator, December, 2003 (Updated December
2006)
Washington State Department of Ecology, 2005 Stormwater Management Manual for Western
Washington, Vol. I-V, April 2005, Available online at
http://www.ecy.wa.gov/biblio/0510029.html
Washington State Department of Ecology, How is Stormwater Regulated, Accessed online in
January 2007 at http://www.ecy.wa.gov/programs/wq/stormwater/municipal/how_regulated.html
Washington State Department of Ecology, Solid Waste In Washington State - Fourteenth
Annual Status Report, Solid Waste and Financial Assistance Program,
Publication No. 05-07-046, December 2005
Wilburn, D.R., Goonan, T.G., Aggregates from Natural and Recycled Sources Economic
Assessments for Construction ApplicationsA Materials Flow Study, U.S. Geological Survey
Circular 1176, 1998, only available online at
http://greenwood.cr.usgs.gov/pub/circulars/c1176/c1176.html
WSDOT, Highway Runoff Manual, Publication Number M 31-16, Washington State
Department of Transportation, May 2006
WSDOT, SS, Standard Specifications M 41-10, 2002,
Washington State Department of Transportation, WA, 2002
WSDOT, Pavement Guide Interactive, Module 3- Aggregate, Authors: Stephen Muench, Joe
Mahoney, Linda Pierce, CD-ROM, Washington Department of Transportation
158
WSDOT, Quieter Pavements: Options and Challenges for Washington State, Prepared by: State
Materials Laboratory, Washington State Department of Transportation
And Acoustics Section Washington State Department of Transportation, May 2005
WSDOT, Traffic Noise Analysis and Abatement Policy and Procedures, Washington State
Department of Transportation, March 2006
WSDOT, Environmental Procedures Manual, Publication Number 31-11, Washington State
Department of Transportation, March 2006
Xiao, F., Amirkhanian, S., Juang, H.C., Rutting Resistance of Rubberized Asphalt Concrete
Pavements Containing Reclaimed Asphalt Pavement Mixtures, ASCE Journal of Materials in
Civil Engineering, MT/2005/023143
159
APPENDIX A:
DESIGN OPTION EVALUATION FOR RECYCLED MATERIALS
Pavement Application
PCC
Asphalt
Fly Ash
Slag-cement
Base
Layer
Workability
Permeability
Water
Reduction
Air
entrainment
Time of set
unstable
++
depend on class
++
--
stable
mitigates
high
albedo
Low
usually bad
Increase
reflectivity
High
noise
reduction
High
++
Scrip Tire
limited
Reclaimed
Asphalt
Recycled
Concrete Material
X
+
++
--
limited
Availability
in WA state
Durability
Glass
Foundry Sand
Other
sustainable
features
(Noise,
stormwater,
albedo)
Strenght
depends
Low
Low
High
High
NOTE: Some of these properties varies with mix design and specific circumstances. This table is only to present common properties generally found
for each recyclable option of material as replacement for virgin material in a pavement application.
160
161
APPENDIX B:
ANALYSIS OF REUSE AND RECYCLED CONTENT
These sheets are examples of the analysis performed for the credit limitations in Material &
Resources, specifically for Reuse of material MR-2 and MR-3, and Recycled Content MR-4 and
MR-5.
162
163
164
165
166
167
168
169
APPENDIX C:
DESIGN OPTION EVALUATION FOR COOL PAVEMENT
APPLICATIONS
Albedo/
Reflectance*
Evaporative
cooling*
(porousity)
Pavement
Application
Low Speed
Low Volume
Road
High Speed
High Volume
Road
Cold Climate
Hot Climate
Wet
Dry
Wet
Other sustainable
features (Noise,
stormwater,
recycled content)
Durability
Dry
Feasability/
Availability in
WA state
Life
Cycle
Cost
Concrete additives
Fly-ash
Yes
Yes
Recycled content
Long
Low
Depends
Slag-cement
Yes
Yes
Recycled content
Long
Low
Depends
Conventional PCC
New,
Resurfacing
Yes
Yes
Recyclability
Long
High
Moderate
Resurfacing
Yes
Yes
Long
High
Moderate
Roller Compacted
Concrete
New
Yes
No
Long
High
Moderate
Light Aggregate in AC
pavement
New,
Resurfacing
Yes
Yes
Moderate
Low
Resurfacing
Yes
No
Skid Resistant
Moderate
Low
Rubberized Asphalt
New,
Resurfacing
Yes
No
Noise, stormwater,
skid resistant,
recycled content
Short
Moderate
High
Porous pavements
Depends
New,
Resurfacing
Yes
No?
Short
Low
High
* Rated 1 to 5 where:
Stormwater
Noise, stormwater,
skid resistant
1= Low
3 = Moderate
5 = High
170
171
APPENDIX D:
INTERVIEW QUESTIONS
Presented here are questions being discussed in interviews.
172
Interview Questions for Contractors (Turner & Skanska).
Personal Interviews were conducted in February 2007.
For a large consulting company as Stantec, how has LEED impacted the way you work with
sustainability and environmental design?
Would you say Stantec has increased its general awareness of sustainability in the last years?
Would you say it is thanks to the implementation of LEED, or is there other regulations or
incentives that force that development?
What has the City of Seattle requirement of LEED silver for commercial buildings really meat
for Stantec in terms of education, implementation and construction activities?
How much education have you put forth through your company to educate the employees of
LEED? Difficulties? Advantages?
How has the implementation of LEED impacted the way you work on an organizational level?
How has the implementation of LEED impacted the way you work in a construction/consultant
activity level? How?
Economical or business level?
In your opinion, how has LEED changed the building construction industry in the U.S.?
Do you think it is successful? Why or why not?
What is working well/not so well?
What would you like to be different or what do you see is missing in regards to LEED?
What is really the level of interest on the construction site for sustainability and environmental
questions? What governs those activities? Money alone?
Is there a marketing benefit in the term sustainability or LEED in your opinion?
How does business and economics work with LEED in your opinion?
How do you see the future of sustainability and construction in the U:S?
What is your reaction of having a similar environmental rating system as LEED but for roadway
design?
173
Interview Questions for Consultant (Stantec Consulting Inc.)
Personal Interview were conducted in February 2007.
Being an office focusing on sustainability, has LEED changed the way you work with
sustainability and environmental design? Why and Why not? How?
Would you say Stantec (not only this office) has increased its general awareness of sustainability
in the last years?
Would you say it is thanks to the implementation of LEED, or is there other regulations or
incentives that force that development?
What are the major limitations in using LEED in a project in your opinion?
Have you seen a change in general awareness among owners, designers and other consultants
in construction projects in regards to sustainability? If so, why is this, LEED or other reasons?
What has the City of Seattle requirement of LEED silver for commercial buildings really meat
for Stantec in terms of education, implementation and consulting activities?
How much education have you put forth through your company to educate the employees of
LEED? Difficulties? Advantages?
How has the implementation of LEED impacted the way you work on an organizational level?
How has the implementation of LEED impacted the way you work in a construction/consultant
activity level? How?
Economical or business level?
In your opinion, how has LEED changed the building construction industry in the U.S.?
Do you think it is successful? Why or why not?
In your opinion, What is working well/not so well?
What would you like to be different or what do you see is missing in regards to LEED?
What is really the level of interest on the construction site for sustainability and environmental
questions? What governs those activities? Money alone?
Is there a marketing benefit in the term sustainability or LEED in your opinion?
How do you see the future of sustainability and construction?
What is your reaction of having a similar environmental rating system as LEED but for roadway
design?
174
Interview Questions for Governmental Organization (King County)
Personal Interview were conducted in February 2007.
Would you say King County has increased its general awareness of sustainability and green
design in the last 5-10 years?
Would you say it is thanks to the implementation of LEED, or is there other regulations or
incentives that have forced that development?
Why did King County decide to require the LEED methodology/tool to be used for all new
buildings, remodels and renovations of your facilities?
In your opinion, how does/did LEED fit in with King Countys already existing regulations and
requirements? The State regulations and requirements? What is not working, what is working?
LEED too stringent or not?
How has LEED impacted the way you work with sustainability?
What is important in your opinion to achieve a successful implementation of LEED in an
governmental organization? Difficulties?
How much education have you put forth through your organization to educate the employees of
LEED? Difficulties? Advantages?
How has the implementation of LEED impacted the way you work on an organizational level?
How has the implementation of LEED impacted the way you work with a policy and regulations?
From King Countys point of view, how has the implementation of LEED impact on an economical
or business level?
In your opinion, has LEED changed the building construction industry in the U.S.? If so, how?
Do you think it is successful? Why or why not?
What is working well/not so well?
What would you like to be different or what do you see is missing in regards to LEED?
Is there a marketing benefit in the term sustainability or LEED in your opinion?
Yes!
How do you see the future of sustainability and construction?
What is your reaction of having a similar environmental rating system as LEED but for roadway
design?
175
APPENDIX E:
LOCATION OVERVIEW OF AGGREGATE SOURCES IN WA (WSDOT)
These illustrations present approved pits and quarries for PCCP and HMA (wearing course and
other courses). The graphs are provided by WSDOT.
176
177
178