Documentos de Académico
Documentos de Profesional
Documentos de Cultura
As Required by the Provisions of the ASME Code Rules, Section VIII, Division 1
1. Manufactured and certified by
(Name and address of Manufacturer)
2. Manufactured for
(Name and address of Purchaser)
3. Location of installation
(Name and address)
4. Type:
(Horiz., vert., or sphere)
(CRN)
(Drawing No.)
(Year built)
Items 611 incl. to be completed for single wall vessels, jackets of jacketed vessels, shell of heat exchangers, or chamber of multichamber vessels.
6. Shell (a) No. of course(s):
(b) Overall length (ft & in.):
Course(s)
No.
Diameter, in.
Material
Thickness
Spec./Grade or Type
Nom.
Corr.
Type
7. Heads: (a)
Eff.
Heat Treatment
Type
Temp.
Eff.
Time
(b)
(Matl Spec. No., Grade or Type) (H.T. Time & Temp.)
Location (Top,
Bottom, Ends)
Thickness
Min.
Corr.
Radius
Crown
Knuckle
Elliptical
Ratio
Conical
Apex Angle
Hemispherical
Radius
Flat
Diameter
Side to Pressure
Convex
Concave
Category A
Type
Eff.
(a)
(b)
8. Type of jacket
Jacket closure
(Describe as ogee & weld, bar, etc.)
9. MAWP
(external)
(internal)
F at
psi.
(external)
at test temperature of
F.
Proof test
(Dia., in.)
(Attachment)
13. Tubes:
(Matl Spec. No., Grade or Type)
(O.D., in.)
(Number)
Items 1418 incl. to be completed for inner chambers of jacketed vessels or channels of heat exchangers.
14. Shell (a) No. of course(s)
(b) Overall length (ft & in.):
Course(s)
No.
Diameter, in.
Material
Thickness
Spec./Grade or Type
Nom.
Corr.
Heat Treatment
Type
Temp.
Eff.
Thickness
Min.
Corr.
Radius
Crown
Knuckle
Elliptical
Ratio
Conical
Apex Angle
Hemispherical
Radius
Flat
Diameter
Side to Pressure
Convex
Concave
Category A
Type
(a)
(b)
(7/00)
Time
(b)
(Matl Spec. No., Grade or Type) (H.T. Time & Temp.)
Location (Top,
Bottom, Ends)
Eff.
This form (E00108) may be obtained from the Order Dept., ASME, 22 Law Drive, Box 2300, Fairfield, NJ 07007-2300.
E00108
Eff.
(external)
F at
psi.
(external)
at test temperature of
F.
Proof test
Diameter
or Size
No.
Lugs
(Yes or no)
Material
Flange
Type
Nozzle
Legs
(No.)
Flange
Nozzle Thickness
Nom.
Corr.
Others
(No.)
Reinforcement
Material
How Attached
Nozzle
Flange
Location
(Insp. Open.)
Attached
(Describe)
21. Manufacturers Partial Data Reports properly identified and signed by Commissioned Inspectors have been furnished for the following items of
the report: (List the name of part, item number, mfgs. name and identifying number)
22. Remarks:
Name
Signed
(Manufacturer)
(Representative)
Signed
Commissions
(Authorized Inspector)
Name
Expires
Signed
(Assembler)
(Representative)
and employed by
of
, have compared the statements in this Manufacturers Data Report with the described pressure vessel
and state that parts referred to as data items
, not included in the certificate of shop inspection, have been
inspected by me and to the best of my knowledge and belief, the Manufacturer has constructed and assembled this pressure vessel in accordance
with the ASME Code, Section VIII, Division 1. The described vessel was inspected and subjected to a hydrostatic test of
psi.
By signing this certificate neither the Inspector nor his employer makes any warranty, expressed or implied, concerning the pressure vessel
described in this Manufacturers Data Report. Furthermore, neither the Inspector nor his employer shall be liable in any manner for any personal
injury or property damage or a loss of any kind arising from or connected with this inspection.
Date
Signed
Commissions
(Authorized Inspector)