Documentos de Académico
Documentos de Profesional
Documentos de Cultura
A
B
C
D
E
Mating Ring
Primary Ring
Retainer
Springs
O-Ring
B
A
E
Optimized
Bi-directional
Pattern
Product Description
The Type 28SC is an extremely compact dry running noncontacting gas seal designed for secondary containment.
Secondary containment seals perform in response to
primary seal leakage or failure and represent a less
complex alternative to dual un-pressurized (tandem) seals
using a Plan 52 lubrication system.
The 28SC is a dry running, non-contacting secondary
containment seal occupying an outboard position in a
cartridge arrangement. Normal leakage from the primary
seal is small and measured in ppm. The use of a
containment seal gland and buffer gas injection moves
vaporous leakage to a flare system. The 28SC is typically
applied with a Plan 72 secondary seal support system.
When called upon to seal gross primary seal leakage,
28SC closes down to run as a contacting seal directing
leakage to flare system or drain.
Performance Capabilities
Pressure:
Up to 44 psi(g)/3 bar(g) (Gas Operation)
Up to 580 psi(g)/40 bar(g) (Liquid Operation)
Design Features
Non-contacting operation
Bi-directional
Compact short axial length
Long life near zero wear
High pressure liquid containment capability
Simplified dual containment using Plan 72
Patented bi-directional groove pattern on mating ring
pumps a small amount of inert buffer gas from the outside
diameter towards the ungrooved portion of the mating ring.
This compressed gas cushion separates the primary seal
face and mating ring and creates a non-contacting seal
Dry-running technology ends need for seal face lubrication
halting frequent maintenance and concern with product
contamination of a lubricating liquid
The unbalanced technology reduces emissions to
minimum
No balance step in shaft, extremely short axial length
Contains process liquid in the event of primary seal failure
and handles up to 580 psi(g)/40 bar(g) in contacting mode
Can operate in a partial vacuum without face and mating
ring contact. Seal can be used in a totally enclosed
containment installation
Large under and over compression allowance for flexible
installation
28SC
TYPE 28SC
28SC
TYPE 28SC
Dry-Running, Secondary Containment Gas Seal
Type 28SC Typical Arrangement/Dimensional Data
L6
0.188
0.157
0.059
0.039
D4
MIN.
BORE
D7
.002
BORE
D3
SEAL
O.D.
D6
.005
D
+ .000
- .002
SHAFT
D44
L3
L8
D
1.000
1.125
1.250
1.375
1.500
1.625
1.750
1.875
2.000
2.125
2.250
2.375
2.500
2.625
2.750
2.875
3.000
3.125
3.250
3.375
3.500
3.625
3.750
3.875
4.000
4.125
4.250
4.375
4.500
D3
2.185
2.307
2.433
2.559
2.685
2.807
2.933
3.059
3.185
3.307
3.433
3.559
3.685
3.807
3.933
4.217
4.343
4.465
4.591
4.717
4.843
4.965
5.091
5.217
5.343
5.465
5.591
5.717
5.843
D4
2.421
2.543
2.669
2.795
2.921
3.043
3.169
3.295
3.421
3.543
3.669
3.795
3.921
4.043
4.169
4.453
4.579
4.701
4.827
4.953
5.079
5.201
5.327
5.453
5.579
5.701
5.827
5.953
6.079
D6
1.785
1.907
2.033
2.159
2.285
2.407
2.533
2.659
2.785
2.907
3.033
3.159
3.285
3.407
3.533
3.816
3.942
4.064
4.190
4.316
4.442
4.564
4.690
4.816
4.942
5.064
5.190
5.316
5.442
D7
2.021
2.143
2.269
2.395
2.521
2.643
2.769
2.895
3.021
3.143
3.269
3.395
3.521
3.643
3.769
4.052
4.178
4.300
4.426
4.552
4.678
4.800
4.926
5.052
5.178
5.300
5.426
5.552
5.678
D13
2.251
2.373
2.499
2.625
2.751
2.873
2.999
3.125
3.251
3.373
3.499
3.625
3.751
3.873
3.999
4.282
4.408
4.530
4.656
4.782
4.908
5.030
5.156
5.282
5.408
5.530
5.656
5.782
5.908
D44
1.246
1.368
1.494
1.620
1.746
1.868
1.994
2.120
2.246
2.368
2.494
2.620
2.746
2.868
2.994
3.120
3.246
3.368
3.494
3.620
3.746
3.868
3.994
4.120
4.246
4.368
4.494
4.620
4.746
L3
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.102
1.181
1.181
1.181
1.181
1.181
1.181
1.181
1.181
1.181
1.181
1.181
1.181
1.181
1.181
L6
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.315
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
L8
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.354
0.394
0.394
0.394
0.394
0.394
0.394
0.394
0.394
0.394
0.394
0.394
0.394
0.394
0.394
D13
.002
GROOVE
TYPE 28SC
Dry-Running, Secondary Containment Gas Seal
Type 28SC Dimensional Data (mm)
Seal Size
(mm)
25.4
28.5
31.7
34.9
38.1
41.2
44.4
47.6
50.8
53.9
57.1
60.3
63.5
66.6
69.8
73.0
76.2
79.3
82.5
85.7
88.9
92.0
95.2
98.4
101.6
104.7
107.9
111.1
114.3
D
25.4
28.5
31.7
34.9
38.1
41.2
44.4
47.6
50.8
53.9
57.1
60.3
63.5
66.6
69.8
73.0
76.2
79.3
82.5
85.7
88.9
92.0
95.2
98.4
101.6
104.7
107.9
111.1
114.3
D3
55.5
58.6
61.8
65.0
68.2
71.3
74.5
77.7
80.9
84.0
87.2
90.4
93.6
96.7
99.9
107.1
110.3
113.4
116.6
119.8
123.0
126.1
129.3
132.5
135.7
138.8
142.0
145.2
148.4
D4
61.5
64.6
67.8
71.0
74.2
77.3
80.5
83.7
86.9
90.0
93.2
96.4
99.6
102.7
105.9
113.1
116.3
119.4
122.6
125.8
129.0
132.1
135.3
138.5
141.7
144.8
148.0
151.2
154.4
D6
45.33
48.43
51.63
54.83
58.03
61.13
64.33
67.53
70.73
73.83
77.03
80.23
83.43
86.53
89.73
96.93
100.13
103.23
106.43
109.63
112.83
115.93
119.13
122.33
125.53
128.63
131.83
135.03
138.23
D7
51.33
54.43
57.63
60.83
64.03
67.13
70.33
73.53
76.73
79.83
83.03
86.23
89.43
92.53
95.73
102.93
106.13
109.23
112.43
115.63
118.83
121.93
125.13
128.33
131.53
134.63
137.83
141.03
144.23
D13
57.17
60.27
63.47
66.67
69.87
72.97
76.17
79.37
82.57
85.67
88.87
92.07
95.27
98.37
101.57
108.77
111.97
115.07
118.27
121.47
124.67
127.77
130.97
134.17
137.37
140.47
143.67
146.87
150.07
D44
31.65
34.75
37.95
41.15
44.35
47.45
50.65
53.85
57.05
60.15
63.35
66.55
69.75
72.85
76.05
79.25
82.45
85.55
88.75
91.95
95.15
98.25
101.45
104.65
107.85
110.95
114.15
117.35
120.55
L3
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
30
30
30
30
30
30
30
30
30
30
30
30
30
30
L6
8
8
8
8
8
8
8
8
8
8
8
8
8
8
8
9
9
9
9
9
9
9
9
9
9
9
9
9
9
L81"
9
9
9
9
9
9
9
9
9
9
9
9
9
9
9
10
10
10
10
10
10
10
10
10
10
10
10
10
10
TYPE 28SC
Dry-Running, Secondary Containment Gas Seal
Materials of Construction
SEAL COMPONENTS
MATERIALS
Description
Standard
Options
Primary Ring
Carbon
Mating Ring
Tungsten Carbide
Silicon Carbide
O-Rings
Fluoroelastomer
Perfluoroelastomer
Nitrile
Ethylene Propylene
Springs
Alloy C-276
Retainer
Set Screws
Thrust Ring
Snap Ring
316 SS
Alloy 20 CB3 SS
Temperature
Fluoroelastomer
Perfluoroelastomer
0F to 500F/-18C to 260C
Nitrile
EPDM
Limits
Surface Finish
0.002"/0.050 mm
+-- 0.063"/1.6 mm
For your nearest John Crane facility, please contact one of the locations below.
North America
Morton Grove, IL, USA
Europe
Slough, UK
Latin America
So Paulo, Brazil
Asia Pacific
Singapore
1-800-SEALING
Tel: 1-847-967-2400
Fax: 1-847-967-3915
Tel: 44-1753-224000
Fax: 44-1753-224224
Tel: 55-11-3371-2500
Fax: 55-11-3371-2599
Tel: 971-481-27800
Fax: 971-488-62830
Tel: 65-6518-1800
Fax: 65-6518-1803
If the products featured will be used in a potentially dangerous and/or hazardous process, your John Crane representative should be consulted prior to
their selection and use. In the interest of continuous development, John Crane Companies reserve the right to alter designs and specifications without
prior notice. It is dangerous to smoke while handling products made from PTFE. Old and new PTFE products must not be incinerated. ISO 9001 and ISO
14001 Certified, details available on request.
2013 John Crane
Revised 09/13
www.johncrane.com
S-28SC