Está en la página 1de 16

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

Package Contents
Autogaurd device is factory shipped along with the following accessories:
AUTOGUARD unit with ABS Plastic enclosure (1 no)
12V 100ma / 110dB - Hooter (Siren sound) (1 no)
Adhesive tape to install device (2 no)
Automotive Grade 6 Pin connector with insulated wire harness (2 feet)
Automotive Grade 2 Pin connector with insulation wire harness (2 feet)
Quick User Guide (1 no)
Warrantee Card (1 no)
Customer Declaration form (1 no)
Installation guide (1 no)
SIM Card Covering Sticker (1 no)

1
2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler guidelines of usage

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

Guidelines for Usage of AUTOGUARD


The below mentioned instructions are intended for your safety and optimal performance of AUTOGUARD. Please read the information
carefully before using AUTOGUARD
General
Warning! AUTOGUARD device may explode if device is exposed or dumped off in fire
Do not open the Plastic housing of AUTOGUARD, as this may affect the performance and warrantee of the product
Do not subject the AUTOGUARD device to extremely high or low temperature more than +70 degree or less than -20 degree
Do not expose your AUTOGUARD to open flames or other flammable gases
Do not drop, throw or try to bend AUTOGUARD device
Do not attempt to disassemble or modify AUTOGUARD device
Do not Disconnect / Move AUTOGUARD device from the place where it is fixed in your vehicle
Do not remove or Replace the SIM card inside AUTOGUARD as this may stop the unit from functioning
Do not solder or change electronic complaints of AUTOGUARD and its accessories
Check you vehicle Battery periodically as AUTOGUARD is fully dependent on vehicle battery for its Operations
Installation
Do not connect AUTOGUARD to external AC or DC power source other than your 12V vehicle battery
Always use standard accessories provided with AUTOGUARD including wire harness, relay and hooter
Do not use your AUTOGUARD device in an area where potentially explosive environment exists
Only authorized personnel Nominated by VAZHIKATTI Systems Limited shall carry out Installation & service on AUTOGUARD
Ensure that all wires are connected in reference with the diagram provided in the manual and ensure minimum stress on wires

2
2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler guidelines of usage

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

Installation Procedure -Attention


Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or
the isolation is damaged, before unplugging the power supply, do not touch the device.
This device must be firmly fastened in a predefined location

This device is susceptible to Water & Humidity if immersed completely

This device should be connected only by Authorized personnel.

This device must be powered from 12V Automotive Battery Supply only
Any installation and/or handling during a lightning storm is prohibited.
Do not replace or remove the SIM card inside the Device.

3
2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler guidelines of usage

VAZHIKAT T I
SECURE

TRACK

CONTROL

Important

Detailed User Guide of AUTOGUARD

The factory shipped device will not have any number stored, the owner needs to assign the primary number for the first time, this can be assigned from any number, once the primary number is assigned and confirmation received the secondary number can then be assigned from the
newly configured primary number. If the primary number is wrongly assigned for the first time then AUTOGUARD can not be used and
needs to be reseated remotely with the support of our call center.
In case GPS fix is not available (this could happen if the vehicle in which AUTOGUARD is fitted is in Basement or under thick vegetation)
AUTOGUARD will try to get the location of the GSM tower that its SIM card is associated to, such location retrieval are called as CELL-ID
location. During query of location via FIND command our server will clearly state weather the locations available is GPS based or CELLID based. GPS location are very accurate however CELL-ID location accuracy will depend on the closeness of the associated cellular tower
which could very from few meters up to few kilometers.
If Auto lock function is enabled then manual lock function via SMS will be disabled, similarly if Auto unlock function is enabled then manual
unlock via SMS will be disabled. During auto unlock function being enabled door opening* will act as unlock function instead of trigger or
alert function.
Dont send SMS commands continuously , It is strongly advisable to wait for confirmation SMS for the previously send command before
sending the next command as there are high possibility that AUTOGUARD will not process continuous commands and may delete such commands without action of confirmation.
During festival seasons or other peak time, there are possibility that the GSM service providers SMS gateways could be chokedand SMS
command sent to AUTOGUARD or send from AUTOGUARD may get delayed or not delivered. It is very important to understand that
AUTOGUARD functionally are fully based on SMS reception and transmission.
The location query command via FIND will normally take between 60 to 120 seconds to be delivered to the vehicle owner. Other commands
may take between 10 to 20 seconds, however the actual time may depend on the GSM operator and network availability.
Siren and Air condition control uses the same hardware circuit, hence only one function can work at any given point of time. If siren if disabled then A/C ON /OFF will work (using additional hardware), if SIREN is enabled then A/C ON/OFF will not work. The additional hardware required which includes a relay and wire harness needs to be purchased separately for authorized dealers.

4
2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

Operating and Command Guide for AUTOGUARD


Autogaurd can be Configured by Sending SMS with specific command mentioned below
Configuration Command to configure AUTOGUARD
1.P=<Primary number of owner>
2.S=<Secondary number of owner>
3.T=<from 10 -60>
4.V=<from 1 to 99>
5.AL=<Yes (Y) or NO (N), (from 1 to 60 minutes)>
6. AU=<Yes (Y) or No (N)>
7.GET
8. SI=<Yes (Y) or No (N)>
9. SMS=<Yes(Y) or No (N)>
10. Reboot
11. Reset

ex: P=+919991122211
ex: S=+919991133311
ex: T=30
ex: V=10
ex: AL=Y,2
ex: AU=Y
ex: GET
ex: SI=Y
ex: SMS=N
ex: REBOOT
ex: RESET

(To Assign Primary or owners number)


(To Assign secondary of co-owners number)
(To set the Trigger & siren time in seconds)
(To set vibration level 1 is highest& 99 is the lowest sensitivity)
(To automatically lock or secure your vehicle)
(To automatically unlock or unsecure your vehicle)
(To provide you with stored information of your configuration)
(To Enable and Disable hooting of siren during Trigger mode)
(To control sending of SMS during lock and unlock command)
(To reboot AUTOGUARD in case of malfunctioning)
(To reset AUTOGUARD to default configuration)

Functional Command to operate AUTOGUARD


1.LOCK
2.UNLOCK
3.OFF
4.ON
5.FIND
6. HOOT
7. AC=OFF
8. AC=ON

ex: LOCK
ex: UNLOCK
ex: OFF
ex: ON
ex: FIND
ex: HOOT
ex: AC=OFF
ex: AC=ON

(To secure or lock the vehicle)


(To unsecure or unlock the vehicle)
(To switch off the ignition of vehicle)
(To switch on the ignition of Vehicle)
(To get the current locations of vehicle)
(To hoot the siren for a specific time default 10 seconds)
(To switch off the Air condition system)*
(To switch on the Air condition system)*

5
2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Important:
Function such as Lock and Unlock are only virtual in nature, they have no relevance to actual Locking or Unlocking of vehicledoors etc.
If Reset command is issued, the entire stored configuration will be lost
AC On/Off will only function if siren is disabled (SI=N) as they share the common wire / Circuit*
Reboot AUTOGUARD only if necessary or during device malfunctioning
During Trigger or Alarm mode the vehicle will be automatically immobilized to prevent vehicle movement
ALL incoming call to AUTOGUARD from authorized and unauthorized numbers will be disconnected without any response or action
Commands send via SMS are not case sensitive, hence upper or lower or both the cases can be used to form a SMS
Grammatical error while typing the SMS command or sending a wrong command will be ignored and an SMS Invalid Command will
be send by AUTOGUARD to Authorized number
For every valid command sent; a reply confirmation will always be send by AUTOGUARD; however the reply time may vary based on
network availability and congestion
Command send to AUTOGUARD by numbers other than Primary and Secondary will be ignored and discarded
There are non space between text which form a command, all the text runs continuously
In case the owner loses or does not have access to both the primary and secondary number, call can be made to our Support Helpline to
reset the unit remotely
During locations query (FIND) if our server does not has correct address or GPS data received from AUTOGUARD is invalid, following
SMS will be send Locations not Available, Kindly retry later in such cases the owner can query AUTOGUARD for location after
few minutes
The Accuracy of Location are based on multiple factors such as Location of Vehicle (indoor or outdoor), Visible GPS satellites and other
environmental factors
In the location SMS, to view the location on a satellite or vector Map, Internet connection via GPRS or Wi-Fi is required
For any given command if there is no response from AUTOGUARD then there could be possibility that the AUTOGUARD is out of
network range or coverage area
If the device is not responding to command for a long time and its LED is in off state then it would be best to contact our support center
or your local dealer to get AUTOGUARD checked or repaired
If the device is removed from its wire harness the vehicle will be automatically immobilized
Every time the device is restarted or rebooted an SMS Powered Onwill be Sent to Primary number

6
2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

To configure Primary number


P=9999911111

AUTOGUARD can Store up to 2 phone numbers from which


it can be controlled (Authorized Numbers). These are called
as Primary and Secondary numbers. Both these numbers have
equal control with respect to AUTOGUARDs functionality.
Once configured AUTOGUARD will only accept SMS or
Call for these two numbers.

SMS Send

P= 9999911111

Confirmation Received

To configure Secondary number


S=9999922222

Both the Primary and Secondary numbers will work parallelly. Owners can also change these numbers in case they
switch operator or opt for a new number by sending similar
SMS. SMS made to AUTOGUARD by other numbers will be
ignored.

SMS Send

S=9999922222

Confirmation Received
7

2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

To configure Trigger timing in seconds

T=10

Trigger time will determine how long AUTOGUARD should


stay in Alert! or active mode during theft. This timing will
also apply to siren hooting interval(10 seconds min to 60 seconds max)

SMS Send

Trigger
Time=10

Confirmation Received

To configure Vibration level of Sensor


V=10

AUTOGUARD has an embedded vibration / movement sensor. In case of vehicle movement this sensor will trigger
which in turn will send alert to user. This SMS can be used to
set the sensitivity of vibration sensor where 01being highest
sensitivity and 99 being the lowest. Users can choose to
change this values based on their needs and requirement

SMS Send

Vibration
Level =10

Confirmation Received
8

2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

Auto Lock
AL=Y,02

Auto Lock as the name suggest can be used to automatically


Lock (Secure) the vehicle. This command can be configured
to be activated within specific time frame (01 minutes being
minimum and 60 being maximum) provided the ignition of
the vehicle is in off state, Door as closed and no moment is
detected. During Auto lock mode manual lock via SMS will
disabled. To disable Auto lock simple send (AL=N)

SMS Send

Auto lock enabled

Confirmation Received

Auto Unlock
AU=Y

Auto Unlock function can be enabled to automatically unlock


the vehicle when doors are opened, Auto unlock can only be
enabled if Auto lock is enabled. During Auto unlock mode
manual unlock via SMS will be disabled. If Auto lock is disabled then Auto unlock will automatically get disabled

SMS Send

Auto unlock enabled

Confirmation Received
9

2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

To view configured parameters


GET

In case owner wants to check the current configuration of


AUTOGUARD including Primary number, Secondary number, Vibration sensor level, Trigger timing, Siren state, Auto
lock status, Auto unlock status, Total SMS sent count and
SMS status, the following SMS can be send to retrieve such
information

SMS Send

P=9999911111,
S=9999922222,
V=10, T=10,SI=Y,
AL=N,02,AU=N,
Total SMS=00050,
SMS=Y

Confirmation Received

Enable and Disable Siren


SI=N

If the owner wants to disable the hooting of siren during trigger mode, the same can be done using this command, N to
disable and Y to enable. This command also has additional
function to activate Air conditioning enabling or disabling
which is optional and requires additional hardware.

SMS Send

SIREN OFF

Confirmation Received
10

2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

SMS
SMS=N

SMS=N
If the user does not wishes to receive confirmation SMS for
Lock and Unlock function the following command may be
send to Deactivate or Activate SMS transmission (SMS=N to
deactivate and SMS=Y to Activate)

SMS Send

Confirmation Received

To Restart AUTOGUARD
RESTART

This command can be issued to restart AUTOGUARD. There


might be remote possibilities that the device could malfunction or may not fully respond to your commands, the following command can be used during such cases. Using this command will not affect or erase your stored configuration.

SMS Send

POWERED ON

Confirmation Received
11

2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

RESET
RESET
RESET command will erase all existing information that has
been stored, which may include primary number, secondary
number etc.. AUTOGUARD will get reseated to factory default setting. No confirmation reply will be send for this command

SMS Send

12
2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

To Secure/Lock the Vehicle


Users can Secure/Lock their vehicle Sending SMS to
AUTOGUARD. In case of movement, door Opening* and
ignition is detected during lock mode AUTOGUARD will
alert its owner by sending an alert SMS. Further the Siren
will make Hoot to scare the thief or alert the neighbors about
possible theft. If Auto lock is enabled then manual lock using
SMS will be disabled.

LOCK

SMS Send

Vehicle Locked

Confirmation Received

To Unsecure/Unlock the Vehicle


UNLOCK

Once unlocked AUTOGUARD will go into passive mode


and will not monitor for Theft of Vehicle, The following
SMS can be send to unsecure/unlock the vehicle. If Auto
unlock is enabled then manual unlock will be disabled

SMS Send

Vehicle Unlocked

Confirmation Received
13

2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

To Switch OFF the vehicle Ignition

OFF
In case the owner wants to switch OFF the ignition of an
moving vehicle the following SMS can be send, once send
the vehicle ignition will stop and can not be started again

SMS Send

Vehicle Switched
OFF

Confirmation Received

To Switch ON the vehicle Ignition


Vehicle switched
ON

ON
This SMS can be send to Switch ON the vehicle which is
Switched OFF, This SMS will switch the vehicle to ON mode
and thus ignition can be started

SMS Send

Confirmation Received
14

2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

To Hoot the Siren

HOOT

In case the you wish to Enable the Siren of the


AUTOGUARD, the following SMS can be send. The siren
will automatically hoot for 10 seconds and stop. No confirmation SMS will be send for this command by
AUTOGUARD

SMS Send

To find the Current location of vehicle

FIND

To find the current location of vehicle the following SMS can


be send to AUTOGUARD. GPRS/3G equipped phone can
also view the vehicle location on MAP by clicking the map
link provided in the return SMS. AUTOGUARD can provide
two kinds of location query (GPS Based) & (CELL-ID
Based), depending on availability of GPS fix.

SMS Send

Vehicle located near


(GPS) Gandhi Puram,
Coimbatore, Tamilnadu on 04/04/2011,
10.30 AM
www.autoguard.in/
location

Confirmation Received
15

2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

Detailed User Guide of AUTOGUARD

VAZHIKAT T I
SECURE

TRACK

CONTROL

Air condition OFF

AC=OFF

By using this command vehicle owner will be able to switch


off the A/C, once A/C is switched the same cannot be switch
ON using A/C button present inside the vehicle. For A/C
OFF command to work the Siren needs to be disabled suing
SI=N command, Additional hardware is required to enable
and disable which is not part of standard AUTOGUARD

SMS Send

A/C Switched
OFF

Confirmation Received

Air condition ON

AC=ON

To switch ON the A/C which has been switched OFF via


SMS command, the following command can be issued. For
A/C ON command to work the siren needs to be disabled using SI=N command. Additional hardware is required to
enable and disable which is not part of standard
AUTOGUARD

SMS Send

A/C Switched
ON

Confirmation Received
16

2012 Vazhikatti Systems Limited. All rights reserved.

Autoguard four wheeler Detailed User Guide

También podría gustarte