Documentos de Académico
Documentos de Profesional
Documentos de Cultura
2)When cutting face of tool is 90 to the line of action of tool then it is known as.
a)Oblique cutting
b)Orthogonal cutting
3)If cutting face of the tool is at less than 90 to the line of action of tool then it is known
as.
a)Orthogonal cutting
b)Oblique cutting
4)Which tool has longer life?
a)Orthogonal tool
b)Oblique tool
5)In Orthogonal cutting chips are in form of..
a)Discontinuous
b)Coils in tight, flat spiral
c)Long curl
6)Metal removal rate of is more
a)Orthogonal tool
b)Oblique tool
7)In oblique cutting chips are in form of..
a)Long curl
b)Flat spiral
c)Discontinuous
d)Short & thick
8)The outward flow of metal causes chips to be when removed from parent
material.
a)Thinner
b)Thicker
9)Torque in milling is determined by formula
a)T=Pz.d2
b)T=pz.d4
c)T=Pz.d
a)Correct
b)Incorrect
37)Tool signature consists of.elements
a)2
b)4
c)5
d)7
38)The factor which affects the tool life is
a)Tool geometry
b)Cutting speed
c)Feed rate
d)All of these
39)Larger end cutting edge angle . Tool life.
a)Increases
b)Decreases
c)No effect
40)The tool lifeas the cutting speed increases.
a)Increases
b)Decreases
41)If the grain size is..tool life is better.
a)Smaller
b)Larger
42)Tool life is affected by..
a)Depth of cut
b)Cutting speed
c)Feed
d)All of these
43)The tool life in case of continuous cutting is much better than intermittent cutting
a)Correct
b)Incorrect
44)The tool life is cutting speed.
a)Independent of
b)Dependent upon
45)Size of lathe is specified by the .
a)Length between centers
b)Swing diameter over the bed
c)Swing diameter over the carriage
d)All of these
46)The swing diameter over carriage is always less than swing diameter over bed.
a)Correct
b)Incorrect
47)Hard and tough materials like cast iron should be turned at.
a)Slow speed
b)High speed
c)Any speed
d)Certain specific speed.
48)The lathe centers are provided with standard taper known as ..
a)Morse taper
b)Seller's taper
c)Capman taper
d)Brown & sharp taper
49)The cutting speed is maximum while machining..with a high speed steel tool.
a)Cast iron
b)Mild steel
c)Brass
d)Aluminium
50)The width of cutting edge of parting tool varies from
a)3-12mm
b)5-20mm
c)8-30mm
d)15-40mm
51)Spot facing is an operation of smoothing and squaring the surface around the hole
a)Correct
b)Incorrect
52)In order to achieve a specific surface finish in single point turning the most important
factor to be controlled is.
a)Depth of cut
b)Cutting speed
c)Feed
d)Tool rake angle
ANSWERS:
1.a 2.b 3.b 4.b 5.b 6.b 7.a 8.b 9.a 10.a
11.a 12.a 13. a 14.a 15. a 16.a 17. a 18.c 19.c 20.a
21.b 22.b 23.d 24.a 25.a 26.d 27.b 28.a 29.a 30.c
31.b 32.d 33.b 34.a 35.d 36.a 37.d 38.d 39.a 40.b
41.b 42.d 43.a 44.b 45.d 46.a 47.a 48.a 49.d 50.a
51.a 52.b