Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Orderingnumber
number: :ENA2107A
ENA2101A
ENA2107
STK433-330N-E
Thick-Film Hybrid IC
http://onsemi.com
Overview
The STK433-330N-E is a hybrid IC designed to be used in 150W 3ch class AB audio power amplifiers.
Application
Audio Power amplifiers
Features
Pin-to-pin compatible outputs ranging from 40W to 150W.
Miniature package.
Output load impedance: RL = 6 recommended.
Allowable load shorted time: 0.3 second
Allows the use of predesigned applications for standby and mute circuit.
Series model
STK433-040N-E
STK433-060N-E
STK433-130N-E
Output1 (10%/1kHz)
40W 2ch
50W 2ch
150W 2ch
25W 2ch
35W 2ch
100W 2ch
38V
46V
71.5V
36V
40V
63V
24V
27V
47.0mm25.6mm9.0mm
44V
67.0mm25.6mm9.0mm
STK433-330N-E
STK433-840N-E
STK433-890N-E
Output1 (10%/1kHz)
150W 3ch
40W 4ch
80W 4ch
100W 3ch
25W 4ch
50W 4ch
71.5V
38V
54V
63V
36V
47V
44V
25V
34V
64.0mm36.6mm9.0mm
64.0mm31.1mm9.0mm
78.0mm44.1mm9.0mm
Specifications
Absolute Maximum Ratings at Ta = 25C, Tc = 25C unless otherwise specified
Parameter
Symbol
Conditions
Non- signal
Signal, RL 6
VCC min
*5
Ratings
Unit
71.5
63
10
-0.3 to +5.5
Thermal resistance
j-c
1.6
C/W
Junction temperature
Tj max
150
Tc max
125
-30 to +125
Storage temperature
Tstg
ts
*4
0.3
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating
Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability.
ORDERING INFORMATION
See detailed ordering and shipping information on page 11 of this data sheet.
Semiconductor Components Industries, LLC, 2013
April, 2013
STK433-330N-E
Operating Characteristics at Tc = 25C, RL = 6 (Non-inductive Load), Rg = 600, VG = 30dB
Conditions *2
Parameter
Output power
Frequency characteristics
Symbol
*1
*1
*1
Input impedance
Output noise voltage
PO 1
44
20 to 20k
0.4
PO 2
44
1k
10
THD 1
44
20 to 20k
THD 2
44
1k
fL, fH
44
44
1k
PO
[W]
THD
min
[%]
96
5.0
VG=30dB
1.0
+0 -3dB
100
53
Rg=2.2k
53
No load
VN
53
VST ON
44
Stand-by
VST OFF
44
Operation
Unit
W
0.4
20 to 50k
%
Hz
55
ICCO
max
0.01
1.0
VNO
*5
typ
150
Quiescent current
*3
[Hz]
ri
Ratings
VCC
[V]
k
1.0
mVrms
60
120
160
mA
-70
+70
mV
0.6
3.0
5.5
2.5
Note
*1. 1channel operation.
*2. All tests are measured using a constant-voltage supply unless otherwise specified
*3. The output noise voltage is peak value of an average-reading meter with a rms value scale (VTVM).
A regulated AC supply (50Hz) should be used to eliminate the effects of AC primary line flicker noise
*4. Allowable time for load short-circuit and output noise voltage are measured using the specified transformer power
supply.
*5. The impression voltage of #13 (Stand-By) pin must not exceed the maximum rating.
Power amplifier operate by impressing voltage +2.5 to +5.5V to #13 (Stand-By) pin.
* Please connect - PreVCC pin (#1 pin) with the stable minimum voltage.
and connect so that current does not flow in by reverse bias.
* In case of heat sink design, we request customer to design in the condition to have assumed market.
* The case of this Hybrid-IC is using thermosetting silicon adhesive (TSE322SX).
* Weight of HIC : (typ) 24.5g
Outer carton dimensions (WLH) : 452mm325mm192mm
DBA40C
10000F
+
+
10000F
+VCC
500
500
-VCC
No.A2107-2/11
STK433-330N-E
Package Dimensions
unit : mm (typ)
64.0
(R1.8)
9.0
25.8
18.7
5.0
36.6
55.6
19
2.9
4.0
3.6
2.0
(9.8)
0.4
0.5
18 2.0=36.0
5.5
Equivalent Circuit
3
8
Pre
Driver
Pre
Driver
Pre
Driver
11
12
Stand-by Circuit
1
2
SUB
5 4 6 7
10
13
14 15 16 17
19 18
No.A2107-3/11
STK433-330N-E
Application Circuit
STK433-330N-E
SUB IC
Ch1
Ch1 Ch1 Ch2 Ch2
-PRE -VCC +VCC OUT OUT OUT OUT +PRE GND GND IN
5
R20
10
11
Ch1
Ch2
NF ST-BY NF
Ch2 Ch3
IN
IN
Ch3
NF
Ch3 Ch3
OUT OUT
12
15
17
18
13
14
16
19
R22
R21
C19
R08
C20
R30
C21
Stand-by Control
R10
R09
C10
C12
C11
C06
R04
+
C05
+
R23
R11
C13
R12
C14
R13
C15
R07
R03
R06
C08
R05
C07
Ch2 IN
GND
C04
Ch1 IN
R02
L03
+VCC
C01
C23
R01
C03
+
R16
L02
R15
C17
R18
-VCC
C18
R19
Ch3 OUT
Ch2 OUT
GND
GND
GND
C02
Ch3 IN
C09
GND
L01
R17
C16
Ch1 OUT
R14
No.A2107-4/11
STK433-330N-E
STK433-040N-E/060N-E/130N-E/330N-E PCB PARTS LIST
PCB Name : STK433 - 000Sr GEVB - A
Location No.
RATING
Component
).
STK433-
040N-E
060N-E
130N-E/
330N-E
R01
100, 1W
1k, 1/6W
56K, 1/6W
1.8K, 1/6W
4.7, 1/4W
4.7, 1W
0.22, 2W
0.22, 5W
100F, 100V
2.2F, 50V
470pF, 50V
3pF, 50V
10F, 16V
0.1F, 50V
***pF, 50V
Jumper
100pF
56pF
3H
Tr1
D1
Di
Stand-By
R30 (*2)
2.7k, 1/6W
(*2)
Control
R31
33k, 1/6W
Circuit
R32
1k, 1/6W
R33
2k, 1/6W
C32
J1, J2, J3, J4, J5, J6, J8, J9
33F, 10V
Jumper
JS8, JS9
JS6, JS10
Jumper
JS1 (R23)
100, 1W
N.C.
Short
No.A2107-5/11
STK433-330N-E
Recommended external components
STK433-040N-E/060N-E/130N-E/330N-E
Parts
Recommended
Location
value
R01, R23
100/1W
Above
Below
Recommended value
Recommended value
Short-through current
Short-through current
may decrease at
high frequency.
frequency.
Circuit purpose
1k
56k
56k
1.8k
It may oscillate.
With especially no
problem
4.7
4.7/1W
0.22/2W
(040N-E,060N-E)
circuit application.
0.22/5W
Note *5
Decrease of
Maximum output
runaway
Power
(130N-E,330N-E)
R30
Select Restriction resistance, for the impression voltage of #17 (Stand-By) pin must not exceed the maximum
rating.
C01, C02
100F/50V
100F/50V
Decoupling capacitor
2.2F/50V
470pF
3pF
10F/10V
It may oscillate.
of low frequency is
of low frequency
extended. However,
decreases.
0.1F
It may oscillate.
100pF (040N-E)
It may oscillate.
56pF (060N-E)
N.C. (130N-E,
330N-E)
L01, L02, L03
3H
With especially
It may oscillate.
no problem
No.A2107-6/11
STK433-330N-E
Pin Layout
[STK433-000N/-100N/-300Nsr Pin Layout]
1
(Size) 47.0mm25.6mm9.0mm
10
11
12
13
14
15
2ch classAB/2.00mm
STK433-040N 40W/JEITA
STK433-060N 50W/JEITA
(Size) 67.0mm25.6mm9.0mm
STK433-130N 150W/JEITA
13
14
15
(Size) 64.0mm36.6mm9.0mm
STK433-330N 150W/JEITA
10
11
12
16
17
18
19
3ch classAB/2.00mm
-
No.A2107-7/11
STK433-330N-E
Characteristic of Evaluation Board
THD-Po
Pd-Po
STK433-330N-E
STK433-330N-E
260
100
Vcc= 44V
RL=6
3ch Drive
VG=30dB
Rg=600
Tc=25C
10
1
f=20kHz
0.1
f=1kHz
0.01
0.001
240
Vcc= 44V
f=1kHz
RL=6
3ch Drive
VG=30dB
Rg=600
220
200
180
160
Tc=25C
140
120
100
80
60
40
20
0
0.1
10
100
1000
0.1
Po-Vcc
100
1000
Po-f
STK433-330N-E
STK433-330N-E
260
200
f =1kHz
RL=6
3ch Drive
VG=30dB
Rg=600
180
Tc=25C
240
220
260
10
THD=10%
160
140
THD=0.4%
120
100
80
60
40
20
0
20
30
40
50
60
240
220
200
180
THD=10%
160
140
THD=0.4%
120
100
Vcc= 44V
RL=6
3ch Drive
VG=30dB
Rg=600
Tc=25C
80
60
40
20
0
10
100
1000
10000
100000
Frequency, f(Hz)
No.A2107-8/11
STK433-330N-E
A Thermal Design Tip For STK433-330N-E Amplifier
[Thermal Design Conditions]
The thermal resistance (c-a) of the heat-sink which manages the heat dissipation inside the Hybrid IC will be
determined as follow:
(Condition 1) The case temperature (Tc) of the Hybrid IC should not exceed 125C
Pd c-a + Ta 125C (1)
Where Ta : the ambient temperature for the system
(Condition 2) The junction temperature of each power transistor should not exceed 150C
Pd c-a + Pd/N j-c + Ta 150C (2)
Where N : the number of transistors (two for 1 channel , ten for channel)
j-c : the thermal resistance of each transistor (see specification)
Note that the power consumption of each power transistor is assumed to be equal to the total power dissipation (Pd)
divided by the number of transistors (N).
From the formula (1) and (2), we will obtain:
c-a (125 Ta)/Pd (1)
c-a (150 Ta)/Pd j-c/N (2)
The value which satisfies above formula (1) and (2) will be the thermal resistance for a desired heat-sink.
Note that all of the component except power transistors employed in the Hybrid IC comply with above conditions.
[Example of Thermal Design]
Generally, the power consumption of actual music signals are being estimated by the continuous signal of
1/8 PO max. (Note that the value of 1/8 PO max may be varied from the country to country.)
(Sample of STK433-330N-E ; 100W3ch)
If VCC is 44V, and RL is 6, then the total power dissipation (Pd) of inside Hybrid IC is as follow;
Pd = 139W (at 12.5W output power,1/8 of PO max)
There are six (6) transistors in Audio Section of this Hybrid IC, and thermal resistance (j-c) of each transistor is
1.6C/W. If the ambient temperature (Ta) is guaranteed for 50C, then the thermal resistance (c-a) of a desired heatsink should be;
From (1) c-a (125 50)/139
0.54
From (2) c-a (150 50)/139 1.6/6
0.45
Therefore, in order to satisfy both (1) and (2), the thermal resistance of a desired Heat-sink will be 0.45C/W.
[Note]
Above are reference only. The samples are operated with a constant power supply. Please verify the conditions when
your system is actually implemented.
No.A2107-9/11
STK433-330N-E
STK433-300 series Stand-by Control & Mute Control & Load-Short Protection
Application
(*1) Please use restriction resistance as there is no Stand-by
terminal voltage (#13pin) beyond maximun rating (VSTmax).
STK433-300N-E series
3
+PRE
SUB
GND
Ch1
IN
Ch1
NF
Ch2
ST-BY NF
Ch2
IN
10
11 12
Ch3
IN
Ch3
NF
13 14
15 16 17 18 19
56k 6.8k
Ch3
OUT
Ch3
OUT
1k
33k
56k 6.8k
33F
/10V
2.7k
(*1)
2k
Stand-by Control(ex)
H:Operation Mode(+5V)
L:Stand-by Mode(0V)
Ch3 IN
56k
56k
0.22
56k 6.8k
Ch2
OUT
0.22
+Vcc
Ch2
OUT
56k
-Vcc
Ch1
OUT
0.22
-PRE
Ch1
OUT
10k
Ch2 IN
10k
GND
10k
22k
56k
Ch1 IN
10k
1k
0.1F
10k
2.2k
V1
Latch Up
Circuit
R1
(*4)
+Vcc
Mute Control
H:Single Mute
L:Normal
Ch3 OUT
Ch2 OUT
Stand-by
Control
GND
GND
GND
GND
-Vcc
+5V
+5V
Mute
Control
MUTE
Ch1 OUT
ST-BY
PLAY
MUTE
ST-BY
(*3)
Stand-by Control
H:Operation Mode(+5V)
L:Stand-by Mode(0V)
33k
2.7K(*1)
VST
VBE
IST
-PRE
-Vcc
+Vcc
Ch1
OUT
Ch1
OUT
Ch2
OUT
Ch2
OUT
STK433-300Nseries
+PRE
SUB
10
11
12 13
GND Ch1
IN
Ch1
NF
ST-BY
14
15
16 17
18
19
Ch2
NF
Ch2
IN
Ch3
IN
Ch3
OUT
Ch3
OUT
VBE
Bias Circuit
in PreDriver IC
4.7k(*2)
Ch3
NF
33F
2k
(*2)
(*3)
Switching transistor
in the bias circuit
No.A2107-10/11
STK433-330N-E
ORDERING INFORMATION
Device
STK433-330N-E
Package
SIP19
(Pb-Free)
ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number
of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLCs product/patent coverage may be accessed at
www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the
application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental
damages. Typical parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customers technical
experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use
as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in
which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for
any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or
death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the
part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PS No.A2107-11/11