Documentos de Académico
Documentos de Profesional
Documentos de Cultura
EQUIPMENT
SELECTION . . . . . . . . . . Ordering No.
TABLE OF
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . Page
PFI1 . . . . . . . . . . . . . . . . . . . . . . . 4311002
Balancer . . . . . . . . . . . . . . . . . . . . 1350147
JARVIS
6223015::
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 064574926
UNITED STATES OF AMERICA
TEL. 8603477271 FAX. 8603476978
2
3
4
5
5
5
6
notice to employer
and safety director
Model PFI1
page 2 of 8
1. Remove and repair any tool that malfunctions. All personnel must be instructed to remove any malfunctioning equipment.
2. Ensure that all employees who use this tool are trained in the proper use of this tool and are aware of
the dangers that may arise if they do not follow procedures outlined in this brochure.
3. Enclosed are four (4) copies of NOTICE TO OPERATORS, MAINTENANCE AND CLEANUP PERSONNEL. Post one copy on the employees bulletin board; give one copy to the operator(s); give one
copy to the maintenance foreman; and give one copy to the subcontract cleanup / internal cleanup foreman. Additional copies will be provided upon request.
4. The tool is designed and intended to be powerful. This fact should be obvious to your employees, but
you must emphasize it to them.
5. Never make modifications or alterations to the tool. Replace any missing or illegible labels.
6. Ensure that proper procedures are established (in accordance with OSHAs lockout/tagout procedures
29 CFR 1910.147) to prevent accidental startup or release of stored energy.
7. Follow our installation and maintenance instructions for proper installation and care of the tool.
8. Avoid injury. Do not permit the tool to be misused.
9. If you resell or distribute a Jarvis product, you must provide the purchaser with the appropriate safety
sheets and tool brochure. Additional copies of safety sheets and tool brochures will be provided upon
request.
JARVIS
6223015::
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 064574926
UNITED STATES OF AMERICA
TEL. 8603477271 FAX. 8603476978
page 3 of 8
1. Disconnect the air hose in accordance with OSHAs lockout/tagout procedures (29 CFR 1910.147) before performing any repair or maintenance.
2. Disconnect the air hose or have the air hose disconnected in accordance with OSHAs lockout/tagout procedures (29 CFR 1910.147) before performing any cleanup.
3. Disconnect the air hose when the tool is not being used.
4. Never put fingers, hands or other parts of the body in the path of the moving claws when tool is activated.
5. Test the tool prior to use or daily. Depress trigger and the claws should move into the frame. Release
the trigger and the claws should move out of the frame. If the tool malfunctions, remove it from service
and report or repair it immediately.
6. Never depress the trigger unless you want to use the tool.
7. Never make modifications or alterations to the tool. Replace any missing or illegible labels.
JARVIS
6223015::
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 064574926
UNITED STATES OF AMERICA
TEL. 8603477271 FAX. 8603476978
page 4 of 8
Figure A
Picking Finger
Insertion Tool
Assembly
*
* If any part of trigger valve assembly kit needs replacing,
the whole assembly kit must be replaced. A Special
tool, Jarvis part number 8330024, is required for valve
bushing removal and installation.
ITEM
1
2
3
4
5
6
7
8
9
10
PART NO.
1323011**
1324078**
1324117
1347020
1301135
1301134
1301133
1336029
1343072
3345001*
11
12
13
14
15
16
17
18
19
20
21
22
23
1302027
1303104
1304121
1301138
1316068
1311035
1343058
1343060
1327128
1349002
1338030
1312060
1317028
PART NAME
Hose Assy (incls. item 2)
Quick Connect Socket
Quick Connect Plug
Handle
Fillister Head Screw
Set Screw
Set Screw
Compression Spring
Oring (package of 5)
Trigger Valve Assy Kit
(includes item 9 )
Hex Lock Nut
Plain Washer
Guard Plate
Pan Head Screw
Spacer
Cam Roller
Ucup Seal
Oring
Pivot Pin
Double Claw (left side)
Bushing
Piston Rod and Yoke
Retaining Ring
JARVIS
6223015::
QTY
1
1
1
1
4
1
1
1
1
1
1
2
2
2
8
4
2
1
1
2
1
4
1
2
**
**
ITEM
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
PART NAME
Single Claw (right side)
Extension Spring
Socket Head Screw
Danger Label
Eye Bolt
Frame and Cyl. Housing.
Bushing
Piston
Hex Jam Nut
Ucup Seal
Oring
End Cap
Retaining Ring
Hex Screw
Oring
Special Tool (not shown)
QTY
1
1
2
1
1
1
1
1
1
2
1
1
1
1
2
1
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 064574926
UNITED STATES OF AMERICA
TEL. 8603477271 FAX. 8603476978
specifications, installation
and operation instructions
Model PFI1
page 5 of 8
SPECIFICATIONS
Model PFI1
Operating Pressure
90 psi
Air Consumption
Per Cycle at 90 psi
Per Cycle at 6.1 bar
6.1 bar
0.091 ft3
2.58 L
Overall Length
12.3 in
312 mm
Overall Width
4.0 in
102 mm
5.9 lbs
2.7 kg
INSTALLATION INSTRUCTIONS
1 Install the PFI1 above the work area from a balancer, if applicable. Jarvis part number 4042022 is
available.
OPERATION INSTRUCTIONS
IMPORTANT: ALWAYS DISCONNECT THE AIR HOSE IN ACCORDANCE WITH OSHAS LOCKOUT/TAGOUT PROCEDURES (29 CFR 1910.147) BEFORE PERFORMING ANY
MAINTENANCE OR REPAIRS.
JARVIS
6223015::
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 064574926
UNITED STATES OF AMERICA
TEL. 8603477271 FAX. 8603476978
maintenance instructions
Model PFI1
Groove
page 6 of 8
1 DAILY: Each day, before you begin operation, go
through the following checklist:
Figure 1
Finger Insertion
Fingers
Single Claw
1.1 Make sure the control trigger is working correctly. Depress the trigger and the claws should
move into the frame. Release the trigger and the
claws should move out of the frame. If the tool
malfunctions, repair or remove it from service
immediately.
Note: Connect the air hose to perform this operation only.
1.2 Inspect all screws, nuts and fasteners and tighten
or replace as necessary.
Barrel Drum
1.3 Inspect air hose and fittings for leaks and tighten
or replace as necessary.
Double Claw
2 AS NECESSARY:
Activate PFI1 to
grasp and pull finger outward away
from barrel drum or
plate.
Place PFI1
against barrel
drum or plate.
Figure above depicts PFI1 with barrel drum containing round fingers. The PFI1 can also be used
for plates and rectangular fingers. Note: Rectangular fingers can only be installed one way. Check
holes for proper orientation.
MAINTENANCE INSTRUCTIONS
IMPORTANT: ALWAYS DISCONNECT THE AIR HOSE IN ACCORDANCE WITH OSHAS LOCKOUT/TAGOUT PROCEDURES (29 CFR 1910.147) BEFORE PERFORMING ANY
MAINTENANCE OR REPAIRS.
IMPORTANT: DISSIPATE STORED ENERGY BEFORE PERFORMING ANY MAINTENANCE OR REPAIRS.
JARVIS
6223015::
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 064574926
UNITED STATES OF AMERICA
TEL. 8603477271 FAX. 8603476978
maintenance instructions
Model PFI1
page 7 of 8
5.4 Remove retaining rings (item 23) and pivot pins
(item 19). Use a pin punch to drive pivot pins out
through holes in cylinder housing (item 29).
Figure 2
Single and Double Claw
Installation
Retaining Ring
Double
Claw
Piston Rod
and Yoke
Pivot Pin
Pivot Pin
Drive Pin
JARVIS
6223015::
7.7 Clean and inspect all parts for wear and replace
them if necessary.
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 064574926
UNITED STATES OF AMERICA
TEL. 8603477271 FAX. 8603476978
maintenance instructions
Model PFI1
page 8 of 8
JARVIS
6223015::
PRODUCTS CORPORATION
33 ANDERSON ROAD, MIDDLETOWN, CONNECTICUT 064574926
UNITED STATES OF AMERICA
TEL. 8603477271 FAX. 8603476978