Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Table of Contents
About PQSCADA Enterprise Analysis Software ............................................. 7 PQSCADA Enterprise System ............................................................... 8 PQSCADA Management Studio ............................................................. 9 PQSCADA Server ........................................................................... 10 Installation .................................................................................... 12 System Requirements..................................................................... 13 Software Requirements .................................................................. 14 Installing the New PQSCADA Software ................................................. 15 Install the New Report Management System .......................................... 18 Upgrading the PQSCADA Management Studio ......................................... 22 Uninstall Previous PQSCADA Management Studio Versions ....................... 23 Installing the New PQSCADA Software............................................... 24 Installing the New Report Management System .................................... 28 Upgrading the Server .................................................................. 32 Upgrading Components ................................................................ 34 Recalculating the Parameters ........................................................ 35 Introduction .................................................................................. 38 View Console............................................................................... 39 Administration Console ................................................................... 49 Tool Bar..................................................................................... 53 Getting Started............................................................................... 54 Starting PQSCADA Management Studio ................................................. 55 Components Creation Wizard ........................................................... 58 Component Details ........................................................................ 62 Commence Data Recording .............................................................. 64 Downloading Recorded Data ............................................................... 66 Log Viewer ................................................................................. 67 Force Connection Attempt ............................................................... 69 Schedule Operation ....................................................................... 70 IP Setup ..................................................................................... 72 Folders Setup .............................................................................. 74 Open Incoming Folder .................................................................... 76 Rescan Device Folders .................................................................... 78 Enable / Disable Data Downloading .................................................... 80 Data Processing .............................................................................. 81 Log Viewer ................................................................................. 84
Force File Parse Attempt ................................................................ 87 Configure Service ......................................................................... 89 Reset PQZIP Files .......................................................................... 93 Folders Setup .............................................................................. 96 Open Incoming Folder .................................................................... 98 Open Bad Files Folder ................................................................... 100 Open Data Backup Folder ............................................................... 102 Enable/Disable Processing .............................................................. 104 Recalculate Data ......................................................................... 106 Swap Phases .............................................................................. 109 Add Factor to Parameters .............................................................. 111 Database ..................................................................................... 113 Log Viewer ................................................................................ 114 Set New Component Database Connection ........................................... 116 Configuration ............................................................................. 118 Re-Index ................................................................................... 122 Delete Log Entries ....................................................................... 123 Database Summary ....................................................................... 124 About PQZIP Upload Manager ............................................................. 126 Using The PQZIP Upload Manager ...................................................... 127 Importing Data............................................................................ 133 Tasks and Templates ....................................................................... 134 Tasks .......................................................................................... 135 Task Types ................................................................................ 136 Task Triggering ........................................................................... 137 Manually Based Task .................................................................. 138 Schedule Based ........................................................................ 140 Event Based ............................................................................ 142 Add Task ................................................................................... 144 Dynamic Folder Path .................................................................. 146 Add General Export Task ............................................................. 148
PQS Parameter Export Task ................................................................ 155
Rerun Tasks ............................................................................... 221 Modify Tasks .............................................................................. 223 Delete Tasks .............................................................................. 225 Monitoring ................................................................................. 227 Task Log ................................................................................... 229 Terminate Task Execution .............................................................. 231 Templates .................................................................................... 233 Add A Template .......................................................................... 234 Select Events ........................................................................... 236 Select Parameter ...................................................................... 237 Select Event Trigger .................................................................. 238 Define Property Configurations ..................................................... 239 Modify Template ......................................................................... 241 Delete Template ......................................................................... 242 Preferences .................................................................................. 243 General Preferences ..................................................................... 244 Regional Settings Preferences .......................................................... 246 Security Settings ......................................................................... 247 File Upload Settings ..................................................................... 249 Appearance Preferences ................................................................ 250 Maps .......................................................................................... 251 Map Tools.................................................................................. 252 Notifications Viewer ........................................................................ 253 Disable Pop-Up Notifications ........................................................... 255 Components ................................................................................. 257 Server ...................................................................................... 258 Add A Server ........................................................................... 259 Connect to Server ..................................................................... 261 Delete Server .......................................................................... 263 General Server Configuration ........................................................ 264
Automatic Maintenance .................................................................... 265 Logger ......................................................................................... 267 E-Mail ......................................................................................... 268 SMS/Text ..................................................................................... 269 Report Management......................................................................... 270 Copy Link ..................................................................................... 272
Site - Description ......................................................................... 274 Add Site ................................................................................. 275 Delete Site.............................................................................. 277 Site - Configuration ................................................................... 279
Name Allocation .......................................................................... 280 Image Selection ........................................................................... 281
Node - Description ....................................................................... 282 Add Node ............................................................................... 283 Remove Node .......................................................................... 287 Node - Configuration .................................................................. 289
General..................................................................................... 290 Device ...................................................................................... 291 Download Schedule ....................................................................... 292 Parameters ................................................................................ 293 Folders ..................................................................................... 298 Database ................................................................................... 299
Encryption About .......................................................................... 307 Install the SSL Certificate ............................................................... 308 Bind the Certificate ...................................................................... 312 Configure PQSCADA to use SSL ......................................................... 314 Change the Communication Binding ................................................... 316 Security - About the Security Module .................................................... 318 Enable the Security Module Locally ................................................... 321 Define the Primary Security Server .................................................... 323 Set User Login Identification ........................................................... 325 User Accounts - About User Accounts ................................................. 326 Create & Add New Users ............................................................. 332 Change User Accounts ................................................................ 335 Tool Tips ..................................................................................... 338 Component Tool Tips .................................................................... 339
Device Tool Tips .......................................................................... 340 Download Status Tool Tip ............................................................... 341 Data Processing Tool Tips ............................................................... 342 Compliance Tool Tips .................................................................... 343 Database Tool Tips ....................................................................... 344 Video Demonstrations ...................................................................... 345 Troubleshooting ............................................................................. 347 Log Viewer ................................................................................ 355
Note: This drawing depicts the master modules initiating the communication The PQSCADA Enterprise System is installed on a personal computer providing unparalleled data monitoring and analysis functionality for all BLACKBOX devices. (For software installation instructions, please refer to Installing the PQSCADA Software).
PQSCADA Management Studio: The user interface (GUI) that is used to configure the PQSCADA Server as well as check status of the components (See PQSCADA Management Studio). PQSCADA Server: A windows serviced based application that runs in the background even when you are not logged in (See PQSCADA Server). Client Application: Elspec Power Quality Investigator. MS SQL Storage: database engine: An SQL Database engine used by the PQSCADA Server to store and process the data.
SEE ALSO
About PQSCADA Enterprise Analysis Software PQSCADA Management Studio PQSCADA Server
The PQSCADA Installation Procedure allows you to install both the PQSCADA Management Studio and the PQSCADA Server (PQS service). In order to stop and/or start the PQS service, you may use the Graphical User Interface (GUI) as below or by accessing the Services through windows configuration.
PQS Service
SEE ALSO
About PQSCADA Enterprise Analysis Software PQSCADA Enterprise System PQSCADA Server
PQSCADA Server
Note: This drawing depicts the flow of data The PQSCADA server is the heart of the BLACKBOX data management and analysis system. The main functionality of the PQSCADA server is shown in the figure above and further described below with corresponding numbered marks: 1. Download: PQSCADA collects all waveform data that has been continuously recorded in the compressed PQZIP format. 2. Process: The data is processed and organized for quick access and storage. A wide range of electrical parameters are then calculated based on the raw PQZIP data. The reorganized PQZIP data, and the calculated parameters with statistics included, are stored and available on the network for later retrieval.
10
3. Deliver: All the electrical information, including event flagging & notifications are delivered over a number of communication gateways. This feature includes report exports in various compatible formats such as COMTRADE, PQDIF, CSV, RTF, HTML, PDF, etc. 4. Visualize: Detailed data can be easily analyzed by any number of clients at any location. The Investigator Software provides an immediate, comprehensive and understandable picture of everything that happened within the network.
SEE ALSO
About PQSCADA Enterprise Analysis Software PQSCADA Enterprise System PQSCADA Management Studio
11
\\
Installation
The PQSCADA software is quite simple to install. Of course before any installation can be performed, you must verify that Minimum System Requirements and Software Requirements are met. There are two installation options:
New Installation: Installing the PQSCADA Software as a new installation Upgrade: Upgrading. an existing version of PQSCADA
12
System Requirements
Regardless of OS: No. of units
1-3
CPU
Later Model Dual Core Later Model Quad Core
RAM
2GB
Storage
3-5 >5
4GB
20-75GB per unit per year, depending on default Cycle By Cycle parameter selection
Contact Support
13
Software Requirements
In order to successfully install PQSCADA, you must first install the following software prerequisites on your system:
Microsoft .Net Framework 4.0 - A Universal platform developed by Microsoft that provides identical functions for a variety of languages (C#, Visual Basic, Java). It is also designed to facilitate development of web applications. (Enable communication between clients and servers).
FOR WINDOWS VISTA SP2 / SERVER 2008 SP2 / XP SP3 / SERVER 2003 SP2:
All of the above, including: Microsoft .Net Framework 3.5 SP1 - A Universal platform developed by Microsoft that provides identical functions for a variety of languages (C#, Visual Basic, Java). It is also designed to facilitate development of web applications. (Enable communication between clients and servers). Windows PowerShell 2.0 - Microsoft's task automation framework, consisting of a command-line shell and associated scripting language built on top of, and integrated with the .NET Framework. PowerShell provides full access to COM and WMI, enabling administrators to perform administrative tasks on both local and remote Windows systems. Microsoft Windows Installer 4.5 - Application installation and configuration service for Windows.
14
3. Select the
4. Read & accept the license agreement at I Agree & select the button:
15
5. The PQSCADA Components screen will now open. (Elspec recommends selecting both components). Select the button:
6. The wizard will now request the location where you would like to install the application. It is recommended to include it on your Hard Drive under an Elspec folder. Either Browse / Type the Location, select the Availability Option & select the button:
16
followed by the
17
TYPES OF REPORTS:
Fault Location Report FOL Compliance Report Chinese Power Quality Report GOST Report NRS 048:2 2007 Report Event Based Compliance Report Power Quality Report (Prodist)
18
In Step 4 of the Installation Process simply select the report of your choosing that you wish to install:
The installation process will automatically run. The installed reports can be viewed on the Report Management's tab within the Server's Configuration.
19
Select the
Read & accept the license agreement at I Agree & select the
The wizard will now request the location where you would like to install the Report & you can choose either option:
Default - Hard Drive under an Elspec folder Preferred Location - As the Reports is independent installations youll need to configure the Report Path:
Select the
button:
20
The installed reports can be viewed on the Report Management's tab within the
Server's Configuration.
21
22
23
The applications setup wizard will guide you through the installation process: 1. At the download location on your hard drive select the PQSCADA Icon:
24
3. Select the
4. Read & accept the license agreement at I Agree & select the
5. The PQSCADA Components screen will now open. Elspec recommends selecting both components. Select the button:
25
6. The wizard will now request the location where you would like to install the application. It is recommended to include it on your Hard Drive under an Elspec folder. Either Browse / Type the Location, select the Availability option & select the button:
followed by the
26
27
TYPES OF REPORTS:
Fault Location Report FOL Compliance Report Chinese Power Quality Report GOST Report NRS 048:2 2007 Report Event Based Compliance Report Power Quality Report (Prodist)
28
In Step 7 of the Upgrading Process simply select the report of your choosing that you wish to install:
The installation process will automatically run. The installed reports can be viewed on the Report Management's tab within the Server's Configuration.
29
Select the
Read & accept the license agreement at I Agree & select the
The wizard will now request the location where you would like to install the Report & you can choose either option:
Default - Hard Drive under an Elspec folder Preferred Location - As the Reports is independent installations youll need to configure the Report Path:
Select the
button:
30
The installed reports can be viewed on the Report Management's tab within the
Server's Configuration.
PROCEED TO THE NEXT STEP: Upgrading the Server.
31
The Main menu appears with the existing Server offline. (In order to add a new server, please refer to Getting Started) Right click at Server is offline, then select Upgrade / Upgrade All:
PQS Server has been updated and brought online with a Site and Node attached that may require an upgrade:
32
Upgrading Components
33
Upgrading Components
We recommend that you upgrade all sites and nodes together for each server; however you may choose to upgrade them individually as well. As shown below Elspec Site & Elspec Node appears but is not yet upgraded or active.
To upgrade all sites and nodes for a server, right click the server (Test server in our example), then select Upgrade / Upgrade All:
The Site (Elspec Site) and Node (Elspec Node) have been upgraded and now appear under PQS Server:
34
from
Version
to Changed/Added Parameters*
In Inter-Harmonics - Phasors
Improvement in the Cycle-by-cycle Frequency DC Included in all Parameters Power Factor included
IEC 61000-4-30 Class A Parameters Included DC Included in most Parameters Unbalance parameters
None
35
3.1.4.5->3.2.0.40
3.1.1.0->3.1.4.5
* All other parameters will have the same values after recalculation
36
37
Introduction
The PQSCADA user interface screen is comprised of three distinct sections; the Tool Bar, Status Bar, and the Main Viewing Area. The Tool Bar contains certain specific functional icons specific to the active console. Two different viewing Consoles are available; View Console and Administration Console. The main viewing area contains all of the Sites / Nodes, Tasks, Templates, Map & PQZIP Upload Manager for the grid.
SEE ALSO:
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
38
View Console
The View mode is divided into two sections - the Top Section & Status Bar. By selecting the buttons on the Top Section you either access directly the Sites / Nodes, Tasks, Templates, Map & PQZIP Upload Manager:
Refresh: To reset the Sites and Nodes if for some reason connection is lost.
NODES/SITES:
This selection allows you to view and modify only the active Sites & Nodes:
TASKS:
This selection allows you to view and modify active Tasks/Templates associated with the Sites:
39
MAP:
A feature which enables you to visually manage the locations of nodes contained within a site by dragging the nodes within the Site MAP and placing them at relevant locations onto a site illustration or image. For more on Maps:
40
STATUS BAR:
The Status Bar is divided into 5 columns & functions can be performed only for the Components:
By selecting any component Server, Site or Node you can perform various functions within each column by a simple right-click of your mouse:
41
COMPONENTS COLUMN:
In this column you may view all the Components including Tool Tips on moving your mouse over the component. perform the following actions:
For the Server: You can Expand, Collapse, Refresh (resets in the event the connection is lost), Copy a Link, Connect, Disconnect, Change the Communication Binding, Login, Logout, Add a Site, View the Log, access the User Manager (only with Security Enabled), View Notifications, Configure the Server & Delete the Server.
For a Site: You can Expand, Collapse, Refresh your view, Add a Node, Add a Site, View the Log, View Notifications, Configure the Site & Delete the Site.
For a Node: You may Refresh (resets in the event the connection is lost), View the Log, Configure the Node & Delete the Node.
42
DEVICE IP COLUMN:
This column provides access to a specific Nodes Device IP settings. You may perform the following actions:
Open the Device in the Web Browser Open the Device in the FTP Access the Device IP Setup, where you may Configure the Device
DOWNLOADING COLUMN:
This column provides control over the downloading process of PQZIP files from the BLACKBOX unit into the PQSCADA Server. The PQSCADA Server system is responsible for collecting continuous data (PQ Zip files) from a connected device. When the device is connected (wired or wireless), the PQSCADA server checks for any new data availability using an FTP communication Protocol. By default the downloading process is disabled, in order to commence the download select the applicable Node select Enable. You may also perform the following actions:
right click
Refresh: Will update you on the Data Downloading status for the Node(s)
Log Viewer: The Log Viewer enables you to see specific information related to log entries with varying levels of importance
Force Connection Attempt (only relevant after the device is enabled): Force Connection Attempt allows you to manually download files
43
from the device to PQSCADA without waiting for the next automatic download attempt
Schedule Operation: Allows you to configure & set a schedule for downloads
IP Setup: Provides access to configure the device's IP settings Folders Setup: This action provides direct access to set the Nodes incoming, backup & bad folder(s) size limits
Open Incoming Folder: With this action it is possible to view all imported PQZIP files that are waiting to be processed
Rescan Device Folders: This action resets the PQZIP folder cache & generate a full folder scan on this device
Refresh: Will update you on the Data Processing status for the Node(s) Log Viewer: The Log Viewer enables you to see specific information related to log entries with varying levels of importance
Force File Parse Attempt: Force Connection Attempt allows you to manually download files from the device to PQSCADA without waiting for the next automatic download attempt
Configure Service: This option will allow you to directly Configure Parameters for the Node, without having to go through Node Configuration
Reset PQZIP files: This function allows you to select and sort the imported PQZIP files & to re-download the processed files
Folders Setup: This action provides direct access to set the Nodes incoming, backup & bad folder(s) size limits
44
Open Incoming Folder: With this action it is possible to view all imported PQZIP files that are waiting to be processed. You may also choose to manually move files from other folders to this folder in order for the PQSCADA to process the data
Open "Bad Files" Folder: With this action it is possible to view all imported PQZIP files that are contained within the Bad Files Folder
Open Data Backup Folder: With this action it is possible to view all imported PQZIP files that are contained within the Backup Folder
Recalculate Data: This action allows you to recalculate the desired parameters. It is recommended that you perform this procedure only when necessary as it may take a considerable amount of time (approximately two weeks to calculate one years worth of data)
En/Disable Processing: By default all imported or created nodes are disabled to process data & therefore needs to enabled
Swap Phases: This operation allows you to swap data between two different voltage phases and neutral, as well as, current phases
Add Factor Parameters: This option allows you to correct & recalculate all the parameters, in the event of an incorrect & invalid setup (i.e. Clamp Setup / PT Ratio correction / CT Ratio correction / Current Polarity)
45
Indicators:
Compliance Type: EN50160/ User Defined / NVE-PQ Norway etc. Date: Date of last recorded compliance Time: Time of last recorded compliance Status (3 States):
Retrieving: Insufficient data present to indicate the status Failed: Overall compliance failed [OK]: Overall compliance succeeded
46
DATABASE COLUMN:
By right clicking on a Server, Site or Node in the Database Column it is possible to access the following configuration tools directly related to the Database:
Refresh: Will update you on the Database status for the Node(s) Log Viewer: The Log Viewer enables you to see specific information related to log entries with varying levels of importance
Set New Database Connection: Allows you to change the server database and/or individual attributes
Configuration: Will provide you with direct access to configuration settings related to the database for either the Server (Automatic Maintenance) &/or Node (Database)
Re-Index: Periodic maintenance operation in order to keep the PQSCADA application running at an optimal speed. This is especially true as the size of the database increases over time
Delete Log Entries: Allows you delete entries according to Log Type and Start/End Date. This action may be carried out for the Server only
Delete Data: This operation removes all binary data in the requested time range from only for the Nodes database, along with, all relevant summaries
Database Summary: A newly added feature the Database Summary provides a detailed summary on any component be that Server, Site & / Node
SEE ALSO:
47
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
48
Administration Console
The Administration console provides functional icons. From the View Console the layout of the administration console changes according the selected View. The three views are Sites/Nodes, Tasks, & Maps. For your convenience the newly added PQZIP Upload Manager remains in both consoles, in order to monitor the status & manage the data upload management at any time . Views:
NODES/SITES:
This selection allows you to view the administration (Server/Site/Node) functions for the selected Server/Site/Node:
Refresh: To reset the Server/Site/Node if for some reason connection is lost Locked: To allow/disallow moving of Site/Node by dragging and dropping. Connect to Server: Connect to a Server Delete Server Database: To Delete Server including Database Add Node: Add a Node(s) to a Site (Adding a Node) Delete Node: Remove a Node from a Site (Deleting a Node) Add Site: Add a Site (Adding a Site) Delete Site: Remove a Site (Deleting a Site)
49
Wizard: Wizard for creating Components (Component Creation Wizard) PQZIP Upload Manager: Manage & control the upload of PQZIP file uploads (PQZIP Upload Manager) PQS Service: To start and stop the PQS Service (PQSCADA Management Studio) Preferences: Global user defined settings for the software (Preferences) Disable Notifications: Select Pop-up Notifications from a list that you wish to disable (please refer to Disable Pop-Up Notifications)
TASKS/TEMPLATES:
Refresh: To reset the Sites and Nodes if for some reason connection is lost Locked/Unlocked: To allow/disallow moving of Sites/Nodes by dragging and dropping Add Task: Add a Task(s) to a Site (Adding a Task) Delete Task: Remove a Task from a Site (Deleting a Task) Add Template: Adding a Template (Adding a Template) Delete Template: Deleting a Template (Deleting a Template) PQS Service: To start and stop the PQS Service (Please refer to PQSCADA Management Studio) Preferences: Global user defined settings for the software (please refer to Preferences) Disable Notifications: Select Pop-up Notifications from a list that you wish to disable (please refer to Disable Pop-Up Notifications)
50
MAPS:
SEE ALSO:
51
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
52
Tool Bar
The tool bar contains icons that represent the Components, Tasks, Templates, & Maps that are used to build the infrastructure as well as manage the Server, Sites & Nodes. The selection of available icons is dependent on the viewing console selected.
In the View Console, it is possible to view all current Server/Sites/Nodes, Tasks, & Maps. The opening default screen is the Sites/Nodes selection in the View Console.
In the Administration Console, it is possible to select functions associated with any of the aforementioned icons.
SEE ALSO:
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
53
Getting Started
This section introduces you to the most basic critical functions of the PQSCADA Management software. It is assumed this is a new installation with no existing Servers, Sites or Nodes, to be upgraded (for upgrading see Upgrading Components). Getting Started guides you through a step-by-step process that includes the following:
Starting PQSCADA Management Studio Creating Components using the Components Creation Wizard Fill in the Component Details Commencing Data Recording
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
For a Tutorial Video Demonstration on PQSCADA Getting Started that provides a step-by-step tutorial that will guide you through the process of setting up your first Server, Site, and Node.
54
All
55
Select the Administration Console. Either right click Server or select Connect to Server tab:
select Connect to
HTTP - Is the default method of communicating with the server. The software uses HTTP port 80 as the default port to communicate with the Node. HTTPS - Is the combination of the Hypertext Transfer Protocol (outlined above) with the SSL protocol to provide encrypted communication and secure identification of a network web server. See Encryption. net.pipe - Improves the connection in case that the server is a local connection. This option will speed up the http connection. Precise URL address of the Server. In this example the Url address for the HTTP connection is localhost/PQS. button.
Select
Should the test for the connection be successful, the message will appear:
56
Select
&
SEE ALSO:
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
For a Tutorial Video Demonstration on PQSCADA Getting Started that provides a step-by-step tutorial that will guide you through the process of setting up your first Server, Site, and Node.
57
Either select the Connect to Server Button or open the wizard by selecting the Wizard Button:
Select Database Engine: Identifies the database engine as an SQL type server.
58
SQL Express Install Button: Launches an automatic installation of the SQL server where most parameters are pre-configured. We recommend using SQL Express only for evaluation purposes. (See Software Requirements).
Browser button: The browser button allows you to search for an available database servers.
Engine Name: The name assigned to the server database engine. User Name: The name of the user as defined for the database server (For SQL Express installed from the BLACKBOX CD, the user name is sa).
Password: User Defined (For SQL Express installed from the BLACKBOX CD, the password is PQSpqs12345).
Test Button: Will test & validate the connection in order to ensure that the details including the Password for the Database Engine are correct.
Set Default Credentials: Will set Server Name, Username & Password to factory defaults.
Save Settings: If you checked this box in one of the Add Server, Add Site, or Add Node dialog boxes, then all attributes are automatically pre-filled; otherwise they will remain blank.
Ensure that all the prerequisites Software Programs are installed prior to installing SQL Express You need to select the button, in order to run the full validation process. This is especially applicable in the event that you may have entered an incorrect password. As such the validation process will be incomplete & the PQSCADA system will prohibit you from performing certain actions.
59
1. Click the Browser button next to the Server name. The Select Database Server window appears. 2. Select Local Servers tab. (You may access remote databases through the Network Servers tab). 3. Double click the desired database or highlight and click Select. 4. Enter your User name and Password. 5. Click Test to verify the connection. 6. Select Save Settings. (Recommended not mandatory; this will set the selected database engine as default and will eliminate the need to reset the database engine at the next attempt of adding sites and nodes). 7. Click Next to continue. The Components Details Window appears.
SEE ALSO:
60
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
For a Tutorial Video Demonstration on PQSCADA Getting Started that provides a step-by-step tutorial that will guide you through the process of setting up your first Server, Site, and Node.
61
Component Details
The Components Details window allows you to enter information about the site and node. Specifically, this is where the site (Elspec Site 1) and node name (Elspec Node 1) are assigned and the desired node IP (100.100.100.100) is selected from the available devices on the network.
1. Enter a name for the server and site. (user defined) 2. Select a device by clicking the Device IP Browser button. 3. The Select Device window appears. The automatic device discovery is activated now and should find all devices on the local LAN if UDP broadcasting is allowed. You may also select the Reload button in this window in order to rescan the devices should some of the devices be missing from the list. 4. Double click the selected device(s). 5. The Name appears in the window. 6. Set the local time to GMT Offset. 7. Click to complete.
62
10. The Server with the Site and Node can be viewed in the main window. PROCEED TO THE NEXT STEP: COMMENCE DATA RECORDING
SEE ALSO:
Starting PQSCADA Management Studio Components Creation Wizard Commencing Data Recording
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
For a Tutorial Video Demonstration on PQSCADA Getting Started that provides a step-by-step tutorial that will guide you through the process of setting up your first Server, Site, and Node.
63
Double
click
the
node
in
the
Data
Processing
Column.
To commence data recording, right click the Node in the Data Download Column, then select Enable. The node is now downloading data from the device.
SEE ALSO:
64
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
For a Tutorial Video Demonstration on PQSCADA Getting Started that provides a step-by-step tutorial that will guide you through the process of setting up your first Server, Site, and Node.
65
By right clicking anywhere in the Downloading Column for the selected device, you may access the following:.
Refresh: Will update you on the Data Downloading status for the Node(s). Log Viewer Force Connection Attempt (only relevant after the device is enabled) Schedule Operation IP Setup Folders Setup Open Incoming Folder Rescan Device Folders (only relevant after the device is enabled) Enable/Disable Data Downloading
66
Log Viewer
The Log Viewer enables you to see specific information related to log entries & in this specific case entries related to downloading process of PQZIP files.
Debug: By default this option is disabled & it is used only by an Elspec Software Technician. Info: Will include general information on actions taken in PQSCADA. In addition, it will also include Warnings, Error & Critical entries. Warning: Will include any malfunctions that the PQSCADA will resolve by itself. The log will also include any Errors & Critical entries. Error: Includes malfunctions that the PQSCADA was unable to resolve. For example failed Tasks due to an incorrect E-Mail address. See Troubleshooting. The log will also include any Critical entries. Critical: Contact Elspec or your local representative.
67
# of Last Entries: This function will enable you to extract only the desired number of Last Entries from the vast amount of all the recorded data, allowing you to focus on the latest relevant data. Start / End Date & Time: Select Start Date & Time option, should you wish to change your search to include entries from a different date & time. Entries in the Log Viewer from this column are related to downloading process of PQZIP files & will initially automatically display these entries. Should you wish, you may Include any other Keywords into your search:
SEE ALSO:
Force Connection Attempt Schedule Operation IP Setup Folders Setup Open Incoming Folder Rescan Device Folders
68
SEE ALSO:
Log Viewer Schedule Operation IP Setup Folders Setup Open Incoming Folder Rescan Device Folders
69
Schedule Operation
To configure & set a schedule for downloads, select Schedule Operation by right clicking the Node in the Downloading Column:
This will open the Download Schedule tab directly in the Node Configuration:
70
Periodic Time to Get File: This is a user defined setting to determine the interval of time to retrieve the PQZIP file(s) from the device. If multiple files exist, this setting is not relevant and there will be no delay. Download Schedule: The specific days and times to perform the file retrieval. Limit Download Time Range: Specifies which files are downloaded that meets a specific date criteria. Enabling this parameter will exclude files that do not fall in the specified time range. File Download Mode: This is a factory setting that should not be changed. Select to set the Download Schedule.
SEE ALSO:
About Downloading Recorded Data Force Connection Attempt Log Viewer IP Setup Folders Setup Open Incoming Folder Rescan Device Folders Enable/Disable Data Downloading
71
IP Setup
To configure device, select IP Setup by right clicking the Node in the Downloading Column:
This will open the Device tab directly in the Node Configuration window:
Enter:
IP Address: Enter the IP address of the device or use the search window browser.
72
User Name: Each device is shipped with a default user name (ftpuser) as above. This name corresponds to the FTP login name set in the firmware of the device (Access Setup section). If you wish to change the user name here, then it also must be changed in the firmware. Password: The password corresponds to the user name above. It should be changed according to the device password. (The default password as shown above is ftppassword). Device PQZIP Folder Path: The specific path where the PQZIP folders are stored on the device. We do not recommend changing this setting. FTP Protocol: The default setting is Passive. Select to complete the Device Configuration.
SEE ALSO:
About Downloading Recorded Data Force Connection Attempt Log Viewer Schedule Operation Folders Setup Open Incoming Folder Rescan Device Folders Enable/Disable Data Downloading
73
Folders Setup
To configure the Folder(s) size limits, select Folders Setup by right clicking the Node in the Downloading Column:
This will open the Folders tab directly in the Node Configuration window:
Set:
74
Incoming Folder Size Limit: The size of the temporary folder where the PQZIP files are stored while they are waiting to be processed. The default is 2 GB, although this can be changes according to your available system resources. All original PQZIP files are deleted after they are processed unless they are backed up. Backup Folder Size Limit: To enable this feature, check the Backup Folder Size Limit check-box. This sets the size of the backup folder where all good PQZIP files can be archived. When the file folder reaches its limit, the oldest files will be deleted first. Bad File Folder Size Limit: The size of the bad file folder where all bad PQZIP files are kept. A file status (good or bad) is determined when the file is processed.
SEE ALSO:
About Downloading Recorded Data Force Connection Attempt Log Viewer Schedule Operation IP Setup Open Incoming Folder Rescan Device Folders Enable/Disable Data Downloading
75
select Open
The PQZIP files are arranged chronologically according to time. (AFTER THE FILES ARE PROCESSED BY THE PQSCADA, THEY WILL NO LONGER APPEAR IN THE INCOMING FOLDER & WILL BE DELETED. SHOULD YOU WISH TO RECALL THE FILES SEE RESET PQZIP FILES). You may select any file(s) from the list:
76
PQSCADA also allows you to download folders as well as files to the incoming folder.
SEE ALSO:
PQZIP Upload Manager Dynamic Folder Path About Downloading Recorded Data Force Connection Attempt Log Viewer Schedule Operation IP Setup Folders Setup Open Incoming Folder Rescan Device Folders Enable/Disable Data Downloading
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
77
SEE ALSO:
About Downloading Recorded Data Force Connection Attempt Log Viewer Schedule Operation IP Setup Folders Setup Open Incoming Folder Enable/Disable Data Downloading
78
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
79
Right click the Node in the Downloading column, then select Enable or Disable.
SEE ALSO:
About Downloading Recorded Data Force Connection Attempt Log Viewer Schedule Operation IP Setup Folders Setup Open Incoming Folder Rescan Device Folders
80
Data Processing
The Data Processing column displays the processing status of PQZIP data. In order to activate the tools for this column, you will need to Enable the function by right clicking anywhere in the Data Processing Column & selecting Enable:
The data processing takes place in 2 stages - namely: Stage 1 - Data Transferral from the PQZIP to the Database, including: Decompression & collection of waveform data sources Data is recompressed into 1min chunks calle d BINARIES The Binaries & Device Events are stored into the Database RMS (V/I) are computed into 1min Summaries After this stage has been concluded, the minimum resolution period that is available for all the parameters, is 3 Hours.
Stage 2 - Data Processing itself: Computation of all other parameter summaries Computation of Class A aggregated parameters (Version 4) Summaries are stored every 1 Min / 10 Min ( Min/Max/AVG) After this stage has been concluded, all queries may run for a period longer than 3 Hours.
Stage 2 computation Queries that are initiated from Elspec's Investigator Software Program for less than 3hours. Any selected parameter is immediately computed from the stored waveform signal in order to achieve a maximum resolution.
The summaries are used for queries that are run for a longer period than 3 Hours & this consequently shortens the response time for such queries.
81
By right clicking anywhere in the Data Processing Column, it is possible to access the following tools:
Refresh: Will update you on the Data Processing status for the Node(s). Log Viewer Force File Parse Attempt Configure Service Reset PQZIP files Folders Setup Open Incoming Folder Open "Bad Files" Folder Open Data Backup Folder En/Disable Processing Re-Index
82
Double-clicking either the Server or Node within this column, will navigate you directly to the following Configuration options: General Configuration for the server & Parameters for the node. On mouse-over Tooltips will appear for each Component.
83
Log Viewer
The Log Viewer enables you to see specific information related to log entries & in this specific case displays entries related to the processing status of PQZIP data.
Debug: By default this option is disabled & it is used only by an Elspec Software Technician. Info: Will include general information on actions taken in PQSCADA. In addition, it will also include Warnings, Error & Critical entries. Warning: Will include any malfunctions that the PQSCADA will resolve by itself. The log will also include any Errors & Critical entries. Error: Includes malfunctions that the PQSCADA was unable to resolve. For example failed Tasks due to an incorrect E-Mail
84
address. See Troubleshooting. The log will also include any Critical entries.
# of Last Entries: This function will enable you to extract only the desired number of Last Entries from the vast amount of all the recorded data, allowing you to focus on the latest relevant data. Start / End Date & Time: Select Start Date & Time option, should you wish to change your search to include entries from a different date & time Entries in the Log Viewer from this column are related to the processing status of PQZIP data & will initially automatically display these entries. Should you wish, you may Include any other Keywords into your search:
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Configure Service Reset PQZIP files
85
Folders Setup Open Incoming Folder Open "Bad Files" Folder Open Data Backup Folder En/Disable Processing Re-Index Delete Data Recalculate Data Swap Phases Add Factor Parameters
86
You may select to force the processing of the PQZIP files manually, by right clicking anywhere in the Data Processing Column Attempt: select Force File Parse
SEE ALSO:
About Data Processing Log Viewer Configure Service Reset PQZIP files Folders Setup
87
Open Incoming Folder Open "Bad Files" Folder Open Data Backup Folder En/Disable Processing Re-Index Delete Data Recalculate Data Swap Phases Add Factor Parameters
88
Configure Service
This option will allow you to directly Configure Parameters for the Node, without having to go through Node Configuration.
select Configure
89
By default, only Cycle by Cycle Waveform is selected. The selection is not permanent therefore you may add more parameters in the future and may recalculate with new parameters.
click
RMS Voltage/Current. HRMS Voltage/Current. THD Voltage/Current. Crest Factor Voltage/Current. K-Factor Current. U1 - Positive Sequence Voltage/Current. U2 - Negative Sequence Voltage/Current. U2/U1 Voltage/Current. U0/U1 Voltage/Current. Active Power Reactive Power Apparent Power Power Factor Frequency 200ms (Device frequency) Waveforms Cycle by Cycle Frequency
Voltage Harmonics Current Harmonics Active Power Harmonics Reactive Power Harmonics
90
Power
Including
Low
Low
Statistics
Low
High
IEC61000-430 Current
Definition
RMS Current HRMS Current THD Current Crest Factor Current U1 - Positive Sequence Current U2 - Negative Sequence Current U2/U1 Current U0/U1 Current Over Deviation Current Under Deviation Current
InterHarmonics
High
High
Inter-Harmonics Angle Inter-Harmonics Phasors Voltage Harmonics Current Harmonics Active Power Harmonics Reactive Power Harmonics Medium High
Harmonics
91
Power
Including
Medium
Low
Aggregation
Medium
High
Frequency Statistics RMS Statistics THD Statistics Active Power Statistics Reactive Power Statistics Apparent Power Statistics Power Factor Statistics
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Reset PQZIP files Folders Setup Open Incoming Folder Open "Bad Files" Folder Open Data Backup Folder En/Disable Processing Re-Index Delete Data Recalculate Data Swap Phases Add Factor Parameters
92
93
The PQZIP File Viewer window for the selected node will now open:
FILTER:
The filter helps you narrow down your search. Select the status for the displayed PQZIP files:
All: This will show all PQZIP files contained in the Incoming Folder. This includes both processed and unprocessed files. It is possible to limit the number of files using the Total Results.
Processed: Only processed files are displayed. Unprocessed: Only unprocessed files are displayed.
Total Results:
Displays total number of PQZIP Files for this node ( All / Processed / Unprocessed)
DELETE SELECTION:
After you have concluded your search, you may re-download and / or re-process any of the files by deleting them from the log. Simply:
& select
94
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Configure Service Folders Setup Open Incoming Folder Open "Bad Files" Folder Open Data Backup Folder En/Disable Processing Re-Index Delete Data Recalculate Data Swap Phases Add Factor Parameters
95
Folders Setup
This option will allow you to directly to the Folder Configuration, without having to go through Node Configuration.
Set Folder(s) size limits by right clicking anywhere in the Data Processing Column select Folders Setup:
Incoming Folder Size Limit: The size of the temporary folder where the PQZIP files are stored while they are waiting to be processed. The default is
96
2 GB, although this can be changes according to your available system resources. All original PQZIP files are deleted after they are processed unless they are backed up.
Backup Folder Size Limit: The size of the backup folder where all good PQZIP files can be archived. When the file folder reaches its limit, the oldest files will be deleted first. Bad Files Folder Size Limit: The size of the bad file folder where all bad PQZIP files are kept. A file status (good or bad) is determined when the file is processed. Set the desired Folder Size Limits click .
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Configure Service Reset PQZIP Files Open Incoming Folder Open "Bad Files" Folder Open Data Backup Folder En/Disable Processing Re-Index Delete Data Recalculate Data Swap Phases Add Factor Parameters
97
In order to view the files, right-click on the Node in the Data Processing Column select Open incoming folder:
The PQZIP files are arranged chronologically according to time. (AFTER THE FILES ARE PROCESSED BY THE PQSCADA, THEY WILL NO LONGER APPEAR IN THE INCOMING FOLDER & WILL BE DELETED. SHOULD YOU WISH TO RECALL THE FILES SEE RESET PQZIP FILES).
98
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Configure Service Reset PQZIP Files Folders Setup PQZIP Upload Manager Dynamic Folder Path Open "Bad Files" Folder Open Data Backup Folder En/Disable Processing Re-Index Delete Data Recalculate Data Swap Phases Add Factor Parameters
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
99
Open the bad PQZIP files in the Bad Files Folder by right clicking anywhere in the Data Processing Column select Open Bad Files Folder:
100
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Configure Service Reset PQZIP Files Folders Setup Open Incoming Folder Open Data Backup Folder En/Disable Processing Re-Index Delete Data Recalculate Data Swap Phases Add Factor Parameters
101
Open the Backed up PQZIP files by right clicking anywhere in the Data Processing Column select Open Backup Files Folder:
102
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Configure Service Reset PQZIP Files Folders Setup Open Incoming Folder Open "Bad Files" Folder En/Disable Processing Re-Index Delete Data Recalculate Data Swap Phases Add Factor Parameters
103
Enable/Disable Processing
By default all imported or created nodes are disabled to process data & therefore needs to enabled.
To commence data recording once again, select Enable by right clicking the Node in the Data Processing Column select Enable:
The node is now processing data from the device. To cease data recording, select Disable by right clicking the Node in the Data Processing Column select Disable:
104
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Configure Service Reset PQZIP Files Folders Setup Open Incoming Folder Open "Bad Files" Folder Open Data Backup Folder Re-Index Delete Data Recalculate Data Swap Phases Add Factor Parameters
105
Recalculate Data
This optional step allows you to recalculate any parameter(s) for a stipulated period. Select this function if you would like to recalculate the latest additional calculations for IEC 61000-4-30 Class A parameters included in PQSCADA 4.2 & later versions.
In Inter-Harmonics - Phasors
Improvement in the Cycle-by-cycle Frequency DC Included in all Parameters Power Factor included
IEC 61000-4-30 Class A Parameters Included DC Included in most Parameters Unbalance parameters
106
3.1.1.0->3.1.4.5
* All other parameters will have the same values after recalculation
Open the recalculation function for a Node by right clicking anywhere in the Data Processing Column select Recalculate Data:
Enter the Time & Date Range from which you would like to recalculate the data:
107
Select
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Configure Service Reset PQZIP Files Folders Setup Open Incoming Folder Open "Bad Files" Folder Open Data Backup Folder En/Disable Processing Re-Index Delete Data Swap Phases Add Factor Parameters
108
Swap Phases
The Swap phases operation allows you to swap data between two different voltage phases and neutral, as well as, current phases.
In order to swap phases click anywhere in the Data Processing Column select Swap Phases:
109
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Configure Service Reset PQZIP Files Folders Setup Open Incoming Folder Open "Bad Files" Folder Open Data Backup Folder En/Disable Processing Re-Index Delete Data Recalculate Data Add Factor Parameters
110
In order to correct & recalculate all the parameters click anywhere in the Data Processing Column select Add Factor To Parameters:
The Add Factor to Parameters Dialog Box will now open. Change the Static Time Period for which you would like to make the correction & Add the Relevant Factor to the applicable parameter select :
111
SEE ALSO:
About Data Processing Log Viewer Force File Parse Attempt Configure Service Reset PQZIP Files Folders Setup Open Incoming Folder Open "Bad Files" Folder Open Data Backup Folder En/Disable Processing Re-Index Delete Data Recalculate Data Swap Phases
112
Database
By right clicking on a Server, Site, or Node in the Database Column it is possible to access the following tools directly related to the database:
Refresh: Will update you on the Database status for the Node(s). Log Viewer Set New Database Connection Configuration (relevant for Server & Nodes only) Re-Index Delete Log Entries (relevant for Server only) Database Summary
Double-clicking either the Server or Node within this column, will navigate you directly to the following Configuration options: Automatic Maintenance for the server & Download Schedule for the node. On mouse-over Tooltips will appear for each Component.
113
Log Viewer
The Log Viewer enables you to see specific information related to log entries & in this specific case displays entries related to the Database.
Debug: By default this option is disabled & it is used only by an Elspec Software Technician. Info: Will include general information on actions taken in PQSCADA. In addition, it will also include Warnings, Error & Critical entries. Warning: Will include any malfunctions that the PQSCADA will resolve by itself. The log will also include any Errors & Critical entries. Error: Includes malfunctions that the PQSCADA was unable to resolve. For example failed Tasks due to an incorrect E-Mail address. See Troubleshooting. The log will also include any Critical entries. Critical: Contact Elspec or your local representative.
# of Last Entries: This function will enable you to extract only the desired number of Last Entries from the vast amount of all the recorded data, allowing you to focus on the latest relevant data.
114
Start / End Date & Time: Select Start Date & Time option, should you wish to change your search to include entries from a different date & time Entries in the Log Viewer from this column are related to the Database & will initially automatically display these entries. Should you wish, you may Include any other Keywords into your search:
SEE ALSO:
About the Database Set New Database Connection Configuration (relevant for Server & Nodes only) Re-Index Delete Log Entries (relevant for Server only) Database Summary
115
The Set New Component Database Connection window will now open:
Select Database Engine: Identifies the database ending as an SQL type server Browser Button: Allows you to search for an available database server Engine Name: The name assigned to the server database engine
116
User Name: The name of the user as defined for the database server (For SQL Express installed from the CD, the user name is sa) Password: User Defined (For SQL Express installed from the CD, the password is PQSpqs12345) Test Button: Will test the connection. PRIOR TO PROCEEDING WITH THIS CHANGE IT IS RECOMMENDED TO VALIDATE & TEST THE CONNECTION IN ORDER TO ENSURE THAT THE DETAILS FOR THE DATABASE ENGINE IS CORRECT. Save Settings: If you checked this box in one of the Add Server, Add Site, Add Node, or Components Creation Wizard dialog boxes, then all attributes are automatically pre-filled; otherwise they will remain blank. Select to change the connection settings.
SEE ALSO:
About the Database Log Viewer Configuration (relevant for Server & Nodes only) Re-Index Delete Log Entries (relevant for Server only) Database Summary
117
Configuration
By selecting the Configuration option in the Database Column for either the Server or Node will provide you with direct access to configuration settings related to the database. DATABASE SERVER CONFIGURATION:
Will provide you with direct access to Automatic Maintenance window in the Sever Configuration:
118
Select Enable Database Maintenance, & when this is checked the operations below occur:
Re-Index: Each table in the database may have one or more indexes. After some time these indexes get fragmented which makes operation on the database take longer. Re-index reorganizes these tables and makes the database faster. Truncate Log: Each database works with 2 files; Data and log. If you are not doing SQL transactional backup, then you should turn this ON. Shrink Log: Truncate log only sets the log file to begin from the start but does not free up the log file space. Shrink log deletes all the unneeded information in the log file. Shrink Database: After some time the database gets fragmented (not disk fragmentation) or has data that is marked for deletion but is not actually deleted from the physical disk. This operation reorganizes the database file on the disk and makes the whole database operation faster. Remove Null Rows: This newly added operation automatically compacts database files with "null row values".
Click
119
Will provide you with direct access to Database window in the Node Configuration:
Allow Truncate Data Automatically: Enabling this feature allows the Node to truncate older data once the database size limit is reached. Limit Data Size in Database: Enabling this feature limits the amount of data in the database to the specified amount. If this limit is reached and "Auto truncate" is not enabled, then the Node won't parse any Node files until data is deleted manually.
120
Limit Aggregated Data Time in Database: Enabling this feature limits the amount of data in the database to the specified time duration. If this limit is reached and "Auto truncate" is not enabled, then the Node won't parse any Node files until data is deleted manually. Set the desired Database Size Limits click .
SEE ALSO:
About the Database Log Viewer Set New Database Connection Re-Index Delete Log Entries (relevant for Server only) Database Summary
121
Re-Index
Re-Indexing the database is a periodically recommended maintenance operation in order to keep the PQSCADA application running at an optimal speed. This is especially true as the size of the database increases over time. With this function you can manually force the re-indexing operation instead of waiting for the automatic re-index of every six hours as set in the Automatic Maintenance of the Server Configuration.
Open the Re-Index function by right clicking anywhere in the Database Column select Re-index:
Select
SEE ALSO:
About the Database Log Viewer Set New Database Connection Configuration (relevant for Server & Nodes only) Delete Log Entries (relevant for Server only) Database Summary
122
Debug: By default this option is disabled & it is used only by an Elspec Software Technician. Info: Will include general information on actions taken in PQSCADA. In addition, it will also include Warnings, Error & Critical entries. Warning: Will include any malfunctions that the PQSCADA will resolve by itself. The log type will also include any Errors & Critical entries. Error: Includes malfunctions that the PQSCADA was unable to resolve. For example failed Tasks due to an incorrect E-Mail address. See Troubleshooting. The log type will also include any Critical entries. Critical: Contact Elspec or your local representative.
SEE ALSO:
About the Database Log Viewer Set New Database Connection Configuration (relevant for Server & Nodes only) Re-Index Database Summary
123
Database Summary
The Database Summary provides a detailed summary on any component be that Server, Site & / or Node.
On the main viewing area select a Component & stand on the Database Column right-click select Database Summary:
124
SEE ALSO:
About the Database Log Viewer Set New Database Connection Configuration (relevant for Server & Nodes only) Re-Index Delete Log Entries (relevant for Server only)
125
Selecting multiple files for PQZIP upload Selecting a root folder location for PQZIP upload Controlling the upload with - Upload, Cancel, Pause & Resume options Uploading the number of concurrent files as per your Preferred File Upload Settings Continuing the PQZIP upload regardless whether or not the PQSCADA is in operation
Utilize the PQSCADA Upload Manager, or Perform Regular Data Imports via the Incoming Folder
126
1. Right-click on the relevant Node (for which you would like to upload the PQZIP files
2. In the File Selection Method dialog box make your selection from the location that you wish to upload the files from:
127
3. Select
128
4. Either mark File (Selects all Files) / Individual Files for which you would like to perform actions on by using the Controls below. Note the Status Column change according to the selected control:
129
Controls:
Action
Resume
Pause
Cancel
Refresh
Reprocess Upload
5. Processed Uploads will be confirmed if the Popups has not been cleared:
130
After you have initiated the Uploading Process as per the previous step, you can monitor & control the process using the PQZIP Upload Manager Icon: 1. Select the PQZIP Upload Manager Icon from either your Administration Console / View Console: 2. The Upload PQZIP Manager will now open Either mark File (Selects all Files) / Individual Files for which you would like to perform actions on by using the Controls below. Note the Status Column change according to the selected control:
Controls:
Action
Resume
Pause
Cancel
Refresh
Reprocess Upload
3. Processed Uploads will be confirmed if the Popups has not been cleared:
131
SEE ALSO:
132
Importing Data
Right click the Downloading column for the device This opens the incoming folder in a separate window.
Accessing the incoming folder allows you to manually download PQZIP files from any location on your PC or external location into the incoming folder instead of from the device.
SEE ALSO:
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
133
The event will trigger the Task The parameters that will be included in the Task The sampling resolution for waveform parameters The sampling resolution for all other parameters excluding waveform parameters
PQDIF, COMTRADE
PQDIF
ALL
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
134
Tasks
Tasks are pre-defined functions that allow you for instance to set regularly scheduled exports; or reports according to a specified event or time trigger (monthly, daily, weekly, and fixed). A task operates within a Site or on components that are attached to a Site. Some tasks require the use of a Template to define the specific parameters of the task. Each task can have multiple Templates. For example: A task that needs to record a voltage dip event, providing both the RMS Voltage and Frequency values during the event , the template is the place where the user defines the desired values. As with most PQSCADA components, you may access the Tasks through either the View or Administration console. The default is View mode. You must first select Tasks in View Mode before switching to administration mode in order to access the Task/Template components. Use the Task Creation Wizard to Add a Task.
SEE ALSO:
Task Types Task Triggering Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
135
Task Types
COMTRADE Task: Output to a COMTRADE file - A universally compatible file format that can be viewed with PQview or TOP. PQDIF Task: Output to a PQDIF file - A Universally compatible file that can be viewed with PQview. PQZIP Task: Output to a PQZIP file - A patented Elspec Compressed file format that can be viewed with Elspecs proprietary Investigator application. Notification Task: This task sends a notification to you with specific results of the completed task. Report Task: This type of task allows you to define a report based upon a Quality Standard, and then publish it to file. Energy Report Task: A task that will combine the TOU configuration output file (produced by the TOU configuration utility) with the amount & makeup (Active or Reactive) of the Net Energy (Received Delivered) produced/consumed by a site in order to calculate the energy produced/consumed in a TOU calendar report profile.
Device Firmware & Configuration Update Task: This task allows you to automatically update all your BLACKBOX Unit(s) via the PQSCADA with any Firmware / Configuration files. PQS Parameters Export Task: This newly added task will create an output file (either CSV / Excel) that includes user-selected parameters, based either on events/schedule, at any desired resolution.
SEE ALSO:
About Tasks Task Triggering Add Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
136
Task Triggering
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
SEE ALSO:
About Tasks Task Types Add Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
137
138
When choosing a Manual Event based task, the Templates Task Wizard is automatically launched in order to allow you define the specific parameters that will launch the Task. See Template. We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
SEE ALSO:
Task Types About Task Triggering Schedule Based Trigger Event Based Trigger Add Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
139
Schedule Based
The task is launched according to a recurring time schedule. All Schedule based tasks can be configured here, not just Comtrade Tasks.
The data schedule is set as recurring for a defined time range ( Daily, Weekly, or Monthly):
140
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
SEE ALSO:
Task Types About Task Triggering Manual Based Trigger Event Based Trigger Add Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
141
Event Based
The task is launched according to an occurrence of a specific event as defined by the Template. An event based task is a task that is defined to be executed given a predefined set of events that may occur in the system.
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
142
SEE ALSO:
Task Types About Task Triggering Manual Based Trigger Schedule Based Trigger Add Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
143
Add Task
When adding a task, the wizard will guide you through this process pending on Types of Tasks you selected. Follow the following procedures in order to add your task:
EXPORT TASKS:
General Export Task: Outlines the procedure for adding a COMTRADE/ PQDIF / PQZIP tasks. PQS Parameters Export Task: Outlines the procedure for producing a CSV/Excel file output that includes selected Parameters (Schedule/Event Based) at any selected Resolution.
REPORT TASKS:
Outlines the procedure for the newly enhanced Report Task that now includes:
Fault Location Report Task: the node. FOL Report Task: Outlines the procedure for producing a PDF file output, for the Norwegian Compliance Standard FOL. Management System Installed) Add Energy Report Task: TOU profile. Outlines the procedure for producing an Excel file (Ensure that you have the new Report Outlines the procedure for producing a PDF file
output that includes the estimated distance from the Main Terminal to the Fault at
output that combines total energy (produced/consumed) for a site with a predefined
NOTIFICATION TASK:
Outlines the procedure for adding a Notification task.
144
SEE ALSO:
About Tasks Task Types Task Triggering Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
145
You can add the Dynamic Folder Path, once you get to the Data Stage in the Task Wizard:
146
Select the Manual Option & in the text box add the applicable characters: ?N: For the Node's Physical Name ?S: For the Site's Physical Name ?P: For the Node's Virtual Name ?Q: For the Site's Virtual Name ?Y: Year ?M: Month ?D: Day ?C: Date formatted as - dd_mm_yyyy ?T: Time formatted as - hh_mm_ss Select your choosing 23_02_2012 02_43_55
After you have selected , the following warning message will appear:
The message serves as reminder that the you should ensure that you have access to your selected Folder Location as the reports will not be created if you don't have access.
Files will be created in the directory as per the example above: C:\PQS\2012\02\29\08_18_43\Elspec_Site_1\Elspec_Node_1
147
COMTRADE, PQDIF &/or PQZIP tasks & PQS Parameters Export Task
2. Click the drop down button to select either: COMTRADE Task, PQDIF Task, PQZIP Task, : enter your own user defined Task Name select
select
148
(ONCE THE TRIGGER TYPE IS SELECTED, IT CANNOT BE CHANGED). (Event trigger not relevant for PQZIP tasks) 5. Choose the Template by either Selecting an Existing Template (Elspec Site) select . Or Define a New Template using : (Not relevant for PQZIP tasks)
6. Make the desired Node Selection select . It is possible to select multiple nodes. By choosing multiple nodes, the task is performed on each of the selected nodes:
149
7. Based on the Trigger Type the wizard will prompt you to set the following report values
select
File Name Prefix: Allocate an easily identifiable file name for your Task (Applicable for COMTRADE, PQDIF & PQZIP) Output Location: (Applicable for COMTRADE, PQDIF, PQZIP & PQS Parameter Export) Select either
Default: The default output location is where the PQSCADA automatically saves the file, or Manually: Save the file in a location of your choosing, by utilizing the newly added feature Dynamic Folder Path in order to more readily identify the folder location & file name.
Type of Data included in Report: The definitions below outlines optional periods based on the Events, Parameters & Resolution defined in the Template. These factors will have a major impact on the amount of data reflected in the report. For instance, events included in the report will include data prior & post
150
the event according to that resolution. The higher the resolution with multiple parameters, the more data is included in the report. Therefore pay particular attention to the time period you choose for your report & ensure that your system is able to support the file size.
Whole Time Period: The report includes the continuous electrical information for the chosen time period, according to the Pre-defined Resolution set in the Template. ENSURE THAT YOUR SYSTEM CAN SUPPORT THE FILE SIZE. (Applicable for COMTRADE & PQDIF) Events Only: The report includes only events that occurred during the selected time period. The duration of each event is as per the Events, Parameters & Resolution defined in the Template. (Applicable for COMTRADE & PQDIF) Whole Time Period & Events: Report includes data for the Whole Time Period & Events (as above) separately according to the Events, Parameters & Resolution defined in the Template. (Applicable for PQDIF only) Enable PQView Compatibility: This will enable users of the PQView Software application to view the PQDIF file in PQView (Applicable for PQDIF only)
COMTRADE VIEW
151
PQDIF VIEW
PQZIP VIEW
152
Enable Popups: Will deliver notifications on the Task completion via Pop-ups on your screen Enable E-Mail: Will send the report / notifications on the Task via listed E-Mails (PRIOR TO INCLUDING THE LIST OF E-MAILS, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND E-MAILS). SMS/Text: Will send the report / notifications on the Task via SMS/Text messages to the listed Cell #'s (PRIOR TO INCLUDING THE LIST OF CELL #'S, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND SMS/Text Messages).
select
to
SEE ALSO:
Task Types Task Triggering About Adding a Task Dynamic Folder Path Add Notification Task
153
Add Report Task Add Device Firmware & Configuration Upgrade Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
154
a warning will appear when selecting the resolution: ENSURE THAT YOUR SYSTEM CAN SUPPORT THE FILE SIZE. The wizard will ask you to base your parameters on the following triggers:
Period: The report will include continuous electrical information for the chosen time period, according to the parameters & defined resolution. Events Only: The report includes only events that occurred during the selected time period. The duration of each event is as per the selected events, parameters & defined resolution. Period & Events: Report includes data for the Whole Time Period & Events (as above) separately according to the Events & Parameters at the defined resolution.
Low Resolution Energy High Resolution* Waveform & Digital IO* Event Log
Period
155
SELECT THESE PARAMETERS ONLY WHEN NECESSARY FOR A SHORT PERIOD & ENSURE THAT YOUR SYSTEM CAN SUPPORT THE FILE SIZE. Events High Resolution Waveform & Digital IO For Period:
Events
&
ENERGY
PARAMETERS
INCLUDING
A PQS Parameter Report including parameters at low resolution reflects parameters measured over time. The parameters will be based on an aggregated period as selected by the user & will provide Min, Max & Average values.
156
K-Factor
Over Deviation
Under Deviation
Positive Sequence
Negative Sequence
Zero Sequence
Unbalance
Zero Unbalance
Active Power
Reactive Power
Apparent Power
Power Factor
RMS
RMS
Peak
Phasors
Flickering *
Frequency *
Analog Input
Analog Output * For Aggregations See Exceptions Aggregation Period 1 Second Base Data
Class A 10/12
3 Seconds
Class A 10/12
10 Seconds
Class A 10/12
30 Seconds
Class A 10/12
157
1 Minute
Class A 10/12
2 Minutes
Class A 10/12
5 Minutes
Class A 10/12
10 Minutes
Class A 10/12
15 Minutes
Class A 10/12
30 Minutes
Class A 10/12
1 Hour
10 Minutes
2 Hours
10 Minutes
Flickering PST
At Resampling: Resolution < 15 Minutes Interpolation based on 10 Minute PST Data: Resolution = 15 Minutes Min/Max: As per All other Parameter Calculations above Average: As per PLT Calculation below
Flickering PLT
At Resampling: Resolution < 15 Minutes Interpolation based on 10 Minute Sliding Window PLT Data: Resolution = 15 Minutes Resolution of Sliding Window Data: Resolution > 15 Minutes
158
Apparent
10 Minutes
15 Minutes
30 Minutes
1 Hour
1 Day
2 Month
159
Parameter Calculation: High Resolution Parameters Resolution 1/2 Cycle Cycle by Cycle Parameters RMS RMS THD Active Power Reactive Power Apparent Power Power Factor RMS THD Active Power Reactive Power Apparent Power Power Factor Harmonic RMS Group 1-50 Harmonic RMS % Group 1-50 Inter-Harmonic RMS Group 1-50
10/12 Seconds
Cycles
Parameters Waveforms: Voltage Channels: V1, V2, V3, VN, V12, V23, V31 Current Channels: I1, I2, I3, IN, I12, I23, I31
16 Samples per Cycle 32 Samples per Cycle 64 Samples per Cycle 128 Samples per Cycle 256 Samples per Cycle 512 Samples per Cycle 1024 Samples per Cycle 16 Samples per Cycle 32 Samples per Cycle 64 Samples per Cycle 128 Samples per Cycle 256 Samples per Cycle 512 Samples per Cycle 1024 Samples per Cycle 16 Samples per Cycle 32 Samples per Cycle 64 Samples per Cycle 128 Samples per Cycle 256 Samples per Cycle 512 Samples per Cycle 1024 Samples per Cycle
160
2. Click the drop down button to select PQS Parameters Export Task Name for your task select :
assign a
select
161
CSV: Select the Applicable Deliminiter (. , : ; _ TAB) for Data Conversion Excel:
Each Node will create a standalone excel file Each Resolution in the requested period will be in a different sheet Default: The default output location is where the PQSCADA
automatically saves the file, or Manually: Save the file in a location of your choosing, by utilizing the newly added feature Dynamic Folder Path in order to more readily identify the folder location & file name.
162
5. Select the Type of Data (Applicable only to PQS Parameters Export) you would like to include
select
Period: The report will include continuous electrical information for the chosen time period, according to the parameters & defined resolution.
Events Only: The report includes only events that occurred during the selected time period. The duration of each event is as per the selected events, parameters & defined resolution.
Period & Events: Report includes data for the Whole Time Period & Events (as above) separately according to the Events & Parameters at the defined resolution.
163
Select:
Enable Low Resolution Parameters Define the Resolution - See Table 1 (The Number of Values will automatically appear to the Right on your selection) The applicable Parameters to be included by using the select : button
Select:
Enable Energy Parameters Define the Resolution - See Table 1 (The Number of Values will automatically appear to the Right on your selection) The applicable Energy Parameters to be included by using the button select :
164
SELECT THESE PARAMETERS ONLY WHEN NECESSARY FOR A SHORT PERIOD & ENSURE THAT YOUR SYSTEM CAN SUPPORT THE FILE SIZE.
Select
Enable High Resolution Parameters Define the Resolution - See Table 2 (The Number of Values will automatically appear to the Right on your selection)
165
button
Select:
Enable Waveform & Digital IO Parameters Define the Resolution - See Table 3 (The Number of Values will automatically appear to the Right on your selection) The applicable Parameters to be included by using the select : button
166
Proceed to Step 7
The applicable Events that will trigger the task by using the button Set the Pre Trigger Margins - Period prior event occurrence Set the Post Trigger Margins - Period post event occurrence select :
167
Select:
Enable High Resolution Parameters (Instantaneous Measured RMS Parameters) Define the Resolution - See Table 2 (The Number of Values will automatically appear to the Right on your selection) The applicable High Resolution Parameters to be included by using the button select :
168
Select:
Enable Waveform & Digital IO Define the Resolution - See Table 3 (The Number of Values will automatically appear to the Right on your selection) The applicable Parameters to be included by using the select : button
Proceed to Step 7
Select:
Enable Low Resolution Parameters Define the Resolution - See Table 1 (The Number of Values will automatically appear to the Right on your selection) The applicable Parameters to be included by using the select : button
169
Select:
Enable Energy Parameters Define the Resolution - See Table 1 (The Number of Values will automatically appear to the Right on your selection) The applicable Energy Parameters to be included by using the button select :
170
SELECT THESE PARAMETERS ONLY WHEN NECESSARY FOR A SHORT PERIOD & ENSURE THAT YOUR SYSTEM CAN SUPPORT THE FILE SIZE.
Select
Enable High Resolution Parameters Define the Resolution - See Table 2 (The Number of Values will automatically appear to the Right on your selection) The applicable Parameters to be included by using the select : button
Select:
171
Define the Resolution - See Table 3 (The Number of Values will automatically appear to the Right on your selection) The applicable Parameters to be included by using the select : button
172
Select:
The applicable Events that will trigger the task by using the button Set the Pre Trigger Margins - Period prior event occurrence Set the Post Trigger Margins - Period post event occurrence select :
Select:
Enable High Resolution Parameters (Instantaneous Measured RMS Parameters) Define the Resolution - See Table 2 (The Number of Values will automatically appear to the Right on your selection) The applicable High Resolution Parameters to be included by using the button select :
173
Select:
Enable Waveform & Digital IO Define the Resolution - See Table 3 (The Number of Values will automatically appear to the Right on your selection) The applicable Parameters to be included by using the select : button
Proceed to Step 7
174
select
8. Select the manner in which you wish to be notified from the available choices by Defining the Notification Type
select
Enable Popups: Will deliver notifications on the Task completion via Pop-ups on your screen. Enable E-Mail: Will send the report / notifications on the Task via listed E-Mails (PRIOR TO INCLUDING THE LIST OF E-MAILS, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND E-MAILS).
SMS/Text: Will send the report / notifications on the Task via SMS/Text messages to the listed Cell #'s (PRIOR TO INCLUDING THE LIST OF CELL #'S, ENSURE THAT YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND SMS/Text Messages).
175
select
to conclude:
SEE ALSO:
Task Types Task Triggering About Adding a Task Dynamic Folder Path
176
Add Notification Task Add Report Task Add Device Firmware & Configuration Upgrade Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
TUTORIAL DEMONSTRATIONS:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
177
The Fault Location Report that provides the estimated distance from the Main Terminal to the fault. Compliance Support Function: by which specific reports can be produced for compliance purposes. Included in this function is the newly added FOL Norwegian Report. The Energy Report Task that combines total energy (produced/consumed) for a site with a predefined TOU profile.
The Report System of the PQSCADA V4.2.2.2 is installed independently from the PQSCADA. This allows the user to effectively manage the reporting system for the entire network. Users simply select & install reports of relevance from any location.
Prior to Installing the new PQSCADA V4.2.2.2 & the new Report Management System all tasks related to report tasks, needs to be reconfigured from anew Backup your old database prior to installing the new Report Management System Ensure that you have Installed the new Reports, in order to utilize this feature
FOL Compliance Report Chinese Power Quality Report GOST Report NRS 048:2 2007 Report Event Based Compliance Report Power Quality Report (Prodist)
178
select
179
4. Choose the Template by either Selecting an Existing Template (Elspec Site) select . Or Define a New Template using :
180
select
It is possible to select multiple nodes. By choosing multiple nodes, the task is performed on each of the selected nodes.
181
7. Based on the Trigger Type the wizard will prompt you to set the following report values select :
182
File Name Prefix: Allocate an easily identifiable file name for your Task Output Format: Acrobat pdf available at this time Output Location: Select either
Default: The default output location is where the PQSCADA automatically saves the file, or Manually: Save the file in a location of your choosing, by utilizing the newly added feature Dynamic Folder Path in order to more readily identify the folder location & file name.
Type of Data included in Report: The definitions below outlines optional periods based on the Events, Parameters & Resolution defined in the Template. These factors will have a major impact on the amount of data reflected in the report. For instance, events included in the report will include data prior & post the event according to that resolution. The higher the resolution with multiple parameters, the more data is included in the report.
183
Therefore pay particular attention to the time period you choose for your report & ensure that your system is able to support the file size.
Whole Time Period: The report includes the continuous electrical information for the chosen time period, according to the Pre-defined Resolution set in the Template. ENSURE THAT YOUR SYSTEM CAN SUPPORT THE FILE SIZE. Events Only: The report includes only events that occurred during the selected time period. The duration of each event is as per the Events, Parameters & Resolution defined in the Template. Whole Time Period & Events: Report includes data for the Whole Time Period & Events (as above) separately according to the Events, Parameters & Resolution defined in the Template. select :
8. Select the manner in which you wish to be notified from the available choices by Defining the Notification Type
Enable Popups: Will deliver notifications on the Task completion via Pop-ups on your screen. Enable E-Mail: Will send the report / notifications on the Task via listed E-Mails (PRIOR TO INCLUDING THE LIST OF E-MAILS, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND E-MAILS). SMS/Text: Will send the report / notifications on the Task via SMS/Text messages to the listed Cell #'s (PRIOR TO INCLUDING THE LIST OF CELL #'S, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND SMS/Text Messages).
184
select
to
SEE ALSO:
About Add Task Dynamic Folder Path Add Export Task Add Notification Task Add Device Firmware & Configuration Update Task Add PQS Parameters Export Task
185
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
186
Prior to Installing the new PQSCADA V4.2.2.2 & the new Report Management System all tasks related to report tasks, needs to be reconfigured from anew Backup your old database prior to installing the new Report Management System Ensure that you have Installed the new Reports, in order to utilize this feature
Names of the Terminals Time the Fault Started Time the Fault Ended Line Information: R1, R0, L1, L0 Frequency Nominal Line Distance (in Meters) Fault Type: (A-Ground, B-Ground, A-B, A-B-C, etc) Fault Graphs Current & Voltage Waveforms Distance Graphs
187
select
select
188
189
5. Choose the Template by either Selecting an Existing Template (Elspec Site) select . Or Define a New Template using :
select
It is possible to select multiple nodes. By choosing multiple nodes, the task is performed on each of the selected nodes.
190
GMT TIME
Main Node (Node Selected Components) Load Node (Lode additional Node)
191
Resolution (Higher the Resolution the more data is included Ensure you have system capacity for higher resolutions)
7. Based on the Trigger Type the wizard will prompt you to set the following report values select :
File Name Prefix: Allocate an easily identifiable file name for your Task Output Format: Acrobat pdf available at this time
192
Default: The default output location is where the PQSCADA automatically saves the file, or Manually: Save the file in a location of your choosing, by utilizing the newly added feature Dynamic Folder Path in order to more readily identify the folder location & file name.
Type of Data included in Report: The definitions below outlines optional periods based on the Events, Parameters & Resolution defined in the Template. These factors will have a major impact on the amount of data reflected in the report. For instance, events included in the report will include data prior & post the event according to that resolution. The higher the resolution with multiple parameters, the more data is included in the report. Therefore pay particular attention to the time period you choose for your report & ensure that your system is able to support the file size.
Whole Time Period: The report includes the continuous electrical information for the chosen time period, according to the Pre-defined Resolution set in the Template. ENSURE THAT YOUR SYSTEM CAN SUPPORT THE FILE SIZE.
Events Only: The report includes only events that occurred during the selected time period. The duration of each event is as per the Events, Parameters & Resolution defined in the Template.
Whole Time Period & Events: Report includes data for the Whole Time Period & Events (as above) separately according to the Events, Parameters & Resolution defined in the Template.
8. Select the manner in which you wish to be notified from the available choices by Defining the Notification Type
select
Enable Popups: Will deliver notifications on the Task completion via Pop-ups on your screen. Enable E-Mail: Will send the report / notifications on the Task via listed E-Mails (PRIOR TO INCLUDING THE LIST OF E-MAILS, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND E-MAILS).
SMS/Text: Will send the report / notifications on the Task via SMS/Text messages to the listed Cell #'s (PRIOR TO INCLUDING THE LIST OF CELL #'S, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND SMS/Text Messages).
193
select
to conclude.
TABLE 1 PARAMETERS:
Parameters R1 R0 L1 L0 Positive Sequence Line Resistance per M (OHM/Km) Zero Sequence Line Resistance per M (OHM/m) Positive Sequence Line Inductance per M (OHM/Km) Zero Sequence Line Inductance per M (OHM/Km) Nominal System Frequency Line length Expressed in Meters Auto a-g Fault Location Type - Instructs the Engine to Identify the Fault Type Fault Location Type - Single Line to Ground Fault:
The faulted phase encounters voltage sag. Two other un-faulted phases encounter voltage swell.
194
b-g
The two faulted phases encounter voltage sag. The other un-faulted phase encounters voltage swell.
c-a
The two faulted phases encounter voltage sag. The other un-faulted phase is unaffected.
SEE ALSO:
Task Types Task Triggering About Adding a Task Dynamic Folder Path Add Notification Task Add Report Task Adding A FOL Report Task Add An Energy Task Add Device Firmware & Configuration Upgrade Task Add PQS Parameters Export Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
195
Prior to Installing the new PQSCADA V4.2.2.2 & the new Report Management System all tasks related to report tasks, needs to be reconfigured from anew Backup your old database prior to installing the new Report Management System Ensure that you have Installed the new Reports, in order to utilize this feature
Summaries:
Detailed Information:
Voltage Frequency Voltage Unbalance RMS Flicker Severity Rapid Voltage Changes Harmonics Voltage (THD) Individual Harmonics Voltages Events - Over / Under Voltages
196
select
select
197
198
5. Choose the Template by either Selecting an Existing Template (Elspec Site) select . Or Define a New Template using :
select
It is possible to select multiple nodes. By choosing multiple nodes, the task is performed on each of the selected nodes.
199
GMT: GMT time offset Line Nominal: Set Nominal Voltage of your Network Show Rapid Voltage Changes at 24 Hour Sliding Window: Select option to display rapid voltage changes table Show Events details: Select option to display events table
200
7. Based on the Trigger Type the wizard will prompt you to set the following report values select :
File Name Prefix: Allocate an easily identifiable file name for your Task Output Format: Acrobat pdf available at this time Output Location: Select either
Default: The default output location is where the PQSCADA automatically saves the file, or Manually: Save the file in a location of your choosing, by utilizing the newly added feature Dynamic Folder Path in order to more readily identify the folder location & file name.
Type of Data included in Report: The definitions below outlines optional periods based on the Events, Parameters & Resolution defined in the Template. These factors will have a major impact on the amount of data reflected in the report. For instance, events included in the report will include data prior & post the event according to that resolution. The higher the resolution with multiple parameters, the more data is included in the report. Therefore pay particular attention to the time period you choose for your report & ensure that your system is able to support the file size.
201
Whole Time Period: The report includes the continuous electrical information for the chosen time period, according to the Pre-defined Resolution set in the Template. ENSURE THAT YOUR SYSTEM CAN SUPPORT THE FILE SIZE.
Events Only: The report includes only events that occurred during the selected time period. The duration of each event is as per the Events, Parameters & Resolution defined in the Template.
Whole Time Period & Events: Report includes data for the Whole Time Period & Events (as above) separately according to the Events, Parameters & Resolution defined in the Template.
8. Select the manner in which you wish to be notified from the available choices by Defining the Notification Type
select
Enable Popups: Will deliver notifications on the Task completion via Pop-ups on your screen. Enable E-Mail: Will send the report / notifications on the Task via listed E-Mails (PRIOR TO INCLUDING THE LIST OF E-MAILS, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND E-MAILS).
SMS/Text: Will send the report / notifications on the Task via SMS/Text messages to the listed Cell #'s (PRIOR TO INCLUDING THE LIST OF CELL #'S, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND SMS/Text Messages).
202
select
to conclude.
TABLE 1 PARAMETERS:
Parameters Frequency RMS Flicker PST Flicker PLT Harmonics Unbalance THD Over / Under Voltage Events Frequency Based on 10 Seconds Data RMS Based on 10 Min Class A Data Flickering Based on 10 Min Data Flickering Based on 2 Hours Data Harmonics Based on 10 Min Class A Data U2/U1 Based on 10 Min Data THD Based on 10 Min Data Dips & Over Voltage
SEE ALSO:
Task Types Task Triggering About Adding a Task Dynamic Folder Path Add Notification Task Add Report Task Adding A Fault Location Report Task Add Device Firmware & Configuration Upgrade Task Add PQS Parameters Export Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
203
2. Click the drop down button to select Energy Task, Task Name select :
204
select
select
It is possible to select multiple nodes. By choosing multiple nodes, the task is performed on each of the selected nodes.
select
205
Excel Template File: This template will serve as the base for which data will be exported to. The template supplied to you by Elspec is divided into two parts. The format of the base part includes: basic data (site & node name, time of recording etc), TOU tariff type & data for each recording. The format of the second part (based on data from the base part) may be customized to suit individual needs. Elspec's template is in a billing format. The template is downloadable from Elspec's Website or from the BLACKBOX installation disc (supplied with every device);
TOU File: This file will determine the TOU profile on which the report will be based. The file is produced using the TOU utility; Energy Duration: Select the duration for the Energy to be recorded that is based on your Task Trigger (every 5, 10, 15, 30 & 60 minutes):
select
206
Define the File Prefix of your choosing, Select the File Output Location (either Default or Manual Option) If you select the Manual Option in the text box add the applicable characters:
?N: For the Node's Physical Name; ?S: For the Site's Physical Name; ?P: For the Node's Virtual Name; ?Q: For the Site's Virtual Name; ?Y: Year; ?M: Month; ?D: Day; ?C: Date formatted as - dd_mm_yyyy Time formatted as - hh_mm_ss 02_43_55; Select example above: C:\PQS\2012\02\29\08_18_43\Elspec_Site_1\Elspec_Node_1 23_02_2012; ?T:
Location of your choosing. Files will be created in the directory as per the
5. Select the manner in which you wish to be notified on the report execution from the available choices by Defining the Notification Type
select
Enable Popups: Will deliver notifications on the report via Pop-ups on your screen. Enable E-Mail: Will send the report via listed E-Mails.(PRIOR TO INCLUDING THE LIST OF E-MAILS, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND E-MAILS).
SMS/Text: Will send notifications on the Task conclusion via SMS/Text messages to the listed Cell #'s. (PRIOR TO INCLUDING THE LIST OF CELL #'S, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND SMS/Text Messages).
207
select
to conclude.
SEE ALSO:
Task Types Task Triggering About Adding a Task Dynamic Folder Path Add Notification Task Add Report Task Adding A Fault Location Report Task Adding A FOL Report Task Add Device Firmware & Configuration Upgrade Task Add PQS Parameters Export Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
208
2. Click the drop down button to select Notification Task, user defined Task Name select :
select
209
5. Choose the Template by either Selecting an Existing Template (Elspec Site) select . Or Define a New Template using :
210
select
It is possible to select multiple nodes. By choosing multiple nodes, the task is performed on each of the selected nodes.
211
7. Select the manner in which you wish to be notified on events from the available choices by Defining the Notification Type
select
Enable Popups: Will deliver notifications on events via Pop-ups on your screen as per the Events, Parameters & Resolution defined in the Template. Enable E-Mail: Will send the report / notifications on the events via listed E-Mails as per the Events, Parameters & Resolution defined in the Template. (PRIOR TO INCLUDING THE LIST OF E-MAILS, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND E-MAILS). SMS/Text: Will send the report / notifications on the Task via SMS/Text messages to the listed Cell #'s as per the Events, Parameters & Resolution defined in the Template. (PRIOR TO INCLUDING THE LIST OF CELL #'S, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND SMS/Text Messages).
212
select
to conclude.
SEE ALSO:
Task Types Task Triggering About Adding a Task Dynamic Folder Path Add Report Task Adding A Fault Location Report Task Adding A FOL Report Task Add An Energy Task Add Device Firmware & Configuration Upgrade Task Add PQS Parameters Export Task Rerun Task
213
Modify Task Delete Task Monitoring Tasks Task Log Terminate Task ExecutionTask Log Terminate Task Execution
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
214
2. Click the drop down button to select Device Firmware & Configuration Update Task assign a Name for your task select :
215
3. Select the following Update &/ Configuration options using the select
button
Select Firmware File: Select the source file for Firmware Update. Allow Downgrade: This option allows you to Update the Firmware according to the file selection. SELECTING THIS OPTION ALLOWS UPDATING THE FIRMWARE, EVEN IF THE FIRMWARE FILE IS AN OLDER VERSION THAN WHAT IS ALREADY INSTALLED IN THE DEVICE. Select Configuration File: This option allows you to configure a device on a pre-defined configuration file.
select
It is possible to select multiple nodes. By choosing multiple nodes, the task is performed on each of the selected nodes.
216
5. In order to review the results for upgrade(s) &/ configuration(s) that will be done for several devices, a progress report is produced (Example). Define the following values for the report
select
File Name Prefix: Allocate an easily identifiable file name for your Task Output Location: It is possible to select the default output location or a user defined (manual) location by utilizing the Browser button
217
6. Select the manner in which you wish to be notified from the available choices by Defining the Notification Type
select
Enable Popups: Will deliver notifications on the Task completion via Pop-ups on your screen. Enable E-Mail: Will send the report / notifications on the Task via listed E-Mails (PRIOR TO INCLUDING THE LIST OF E-MAILS, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND E-MAILS). SMS/Text: Will send the report / notifications on the Task via SMS/Text messages to the listed Cell #'s (PRIOR TO INCLUDING THE LIST OF CELL #'S, ENSURE THAT THE YOUR SERVER IS CONFIGURED WITH THE CORRECT SETTINGS IN ORDER TO SEND SMS/Text Messages).
218
select
to conclude.
SEE ALSO:
Task Types Task Triggering About Adding a Task Dynamic Folder Path Add Export Task Add Notification Task Add Report Task Add PQS Parameters Export Task Rerun Task Modify Task Delete Task
219
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
220
Rerun Tasks
You may re-execute any Task at any time by right-clicking the Task (Elspec Task in our example), then select Rerun Task:
SEE ALSO:
About Tasks Task Types Task Triggering Add Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log Terminate Task Execution
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
221
222
Modify Tasks
Right click the Task (Elspec Task in our example), then select Modify Task:
SEE ALSO:
About Tasks Task Types Task Triggering Add Task Delete Task Monitoring Tasks Task Log Terminate Task Execution Rerun Task
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
223
224
Delete Tasks
Right click the Task (Test in our example), then select Delete Task, or select Delete Task from the Administration Console tool bar:
SEE ALSO:
About Tasks Task Types Task Triggering Add Task Delete Task Monitoring Tasks Task Log Terminate Task Execution Rerun Task
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
225
226
Monitoring
The Monitoring bar (highlighted in yellow) displays the current status of the:
Status: The status of the task, (idle or running) Last Operation: The last time the task was completed. Next Operation: The next time the task is scheduled to run. Result: The result of the last task operation. It is possible to view details in Task Log.
SEE ALSO:
About Tasks Task Types Task Triggering Add Task Rerun Task Modify Task Delete Task Task Log Terminate Task Execution
227
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
228
Task Log
The Task Log displays all log entries for a give task defined by a date range. The logs entries can also be limited by a user defined number of records per task. In the lower part of the Event Viewer below, you can see each individual log entry, with its start time and result. In the Description column, it is possible to open the folder containing the log files.
SEE ALSO:
About Tasks Task Types Task Triggering Add Task Rerun Task Modify Task Delete Task Monitoring Tasks Terminate Task Execution
229
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
230
You may terminate a Task at any time by right-clicking the Task Terminate current execution:
select
SEE ALSO:
About Tasks Task Types Task Triggering Add Task Rerun Task Modify Task Delete Task Monitoring Tasks Task Log
231
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
232
Templates
Templates are used to define the Events, Parameters, and Configurations for utilization by different tasks. By using templates, you can save the time of redefining all variables across multiple tasks. A single template can serve multiple tasks & in return the task will only utilize the necessary components from that template needed to execute the task. Summary of Template Components & Related Tasks: Template Components Events Description Task Related
Parameters
The parameters that will be included in the Task The sampling resolution for waveform parameters The sampling resolution for all other parameters excluding waveform parameters The recording time of the Event
PQDIF, COMTRADE
PQDIF
ALL
SEE ALSO:
233
Add A Template
1. Right click Templates, then select Add Templates or select Add Template from the Administration Console tool bar. The Template Wizard is automatically launched which guides you through a step-by-step process of creating a Template. 2. Enter a name for the template in the Template Name window : select
234
3. Select an Event(s) from drop down list of Available Events, then click the middle cursor button to move the selection(s) to Selected events. The Selected Events now appear in the right pane. 4. Select a Parameter(s) from drop down list of Available Parameters, then click the middle cursor button to move the selection(s) to Selected Parameters (only relevant for PQDIF task). 5. Select the Event Trigger from Property Definitions Window. 6. Define Property Configurations using the Event Trigger Limitations window (only relevant for PQDIF and Comtrade tasks). 7. Click to complete.
When exporting data to a PQDIF file, the parameters exported depend on the parameters in the selected template and the user selection at the end of the PQDIF wizard.
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
235
Select Events
Open Available Events & select any item use the / Selected Events:
Select
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
236
Select Parameter
After Event Selection:
Double Click or
alternatively use the / buttons in order to transfer items to & from Available & Selected Parameters:
Select
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
237
Available Triggers:
Start of the Event: Selecting this option will register the associated task at the beginning of an event. End of the Event: Selecting this option will register the associated task at the end of an event. Start & End of the Event: Selecting this option will register the associated task at the beginning & the end of an event. & go on to the next step Select Parameters.
Select
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
238
where needed:
High Resolution: Primarily used for short time intervals (waveforms). In our example we use 6400 which is calculated from 50Hz * 128 samples per cycle. Low Resolution: Primarily used for longer time intervals (minutes, seconds). In our example we select 1.0 update per second rate. Pre-Trigger Margin: An additional time period (margin) is taken before the trigger is scheduled. Post-Trigger Margin: An additional time period (margin) is taken after the trigger is scheduled. to create the template:
239
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
240
Modify Template
SEE ALSO:
241
Delete Template
Right click the Template (Test in our example) select Delete Template / select Delete Template from the Administration Console tool bar.
SEE ALSO:
242
Preferences
In the Administration Console, the global Preferences for the software are established in this section. Preferences: From the Administration Console select
General Preferences Regional Settings Preferences Security Settings - See Also Encryption File Upload Settings - See Also PQZIP Upload Manager Appearance Preferences
243
General Preferences
Reset Default Settings: Pressing the Load button restores all of the system default settings. Minimize to System Tray: The PQSCADA icon will reside in the bottom system tray when minimized. Double click the icon to restore the window. (Default is unchecked)
Hide Splash Screen: The opening splash screen does not appear when launching the program. This may be essential in some cases when connected remotely to a computer running the management console. (default is unchecked)
SEE ALSO:
About Preferences
244
Regional Settings Preferences Security Settings - See Also Encryption File Upload Settings - See Also PQZIP Upload Manager Appearance Preferences
245
Language: A selection of regional languages. Time Settings: Change this setting if you would like to see all dates and time according to a different time zone (User Defined Time according to GMT). The default is System time.
SEE ALSO:
About Preferences General Preferences Security Settings - See Also Encryption File Upload Settings - See Also PQZIP Upload Manager Appearance Preferences
246
Security Settings
Selecting this preference will take you directly to the Activation of the SSL protocol (Secure Socket Layer) for enabling secure, encrypted communication between PQSCADA Management Studio and Investigator which are both client software, and the PQSCADA Server. Furthermore, the certificate can also provide proof of the servers identity should the administrator choose to purchase and install a commercial certificate from a trusted CA. The new PQSCADA Installation (V4.1 +) includes a certificate for a SSL protocol. This is in addition to the newly added Security Module for the PQSCADA & may used independently or in combination with this module.
click
Preference Levels:
Low Level: Discards any errors which may occur due to an invalid certificate. Medium Level: May identify when an invalid certificate is being used, but will ask the user to accept the invalid certificate. High Level: Requires a valid certificate & will not proceed if it is not present.
247
SEE ALSO:
About Preferences General Preferences Regional Settings Preferences Security Settings - See Also Encryption File Upload Settings - See Also PQZIP Upload Manager Appearance Preferences
248
Select the File Upload Settings Tab, & set the your choice of preference in:
SEE ALSO:
About Preferences General Preferences Regional Settings Preferences Security Settings - See Also Encryption Appearance Preferences
249
Appearance Preferences
Select Skin: This option allow you to select the background color of the GUI. PQS Default is black; alternatively you may also select a light blue background. Refresh Screen: How often the screen is refreshed with new data. Lowering this value will result in a faster refresh rate, but will also cause the management studio to use more system resources. The default is: 1000 ms. Popup Settings:
Maximum Displayed Popups: This option allows you to set the maximum number of Popup Notifications you want to be displayed on your screen.
Enable Beep with Popup: You may set a beep sound for when a popup appears. The file needs to be in WAVE format with PCM encoding & therefore end with *.wav.
Enable Font Correction: This allows the software to correct some font issues with certain Operating Systems.
SEE ALSO:
250
Security Settings - See Also Encryption File Upload Settings - See Also PQZIP Upload Manager
Maps
A view which enables you to visually manage the locations of nodes contained within a site by dragging the nodes within the Site MAP. The background for the MAP is an external image file that is imported into the PQSCADA software using Site Image Configuration.
Each BLACKBOX image contained within the MAP represents an individual node within the Site. The Node (Elspec Node 1) that is highlighted in the Components section has a corresponding highlight (yellow) on the MAP. The images can be placed anywhere on the background image (MAP) by simply dragging and dropping with the mouse.
SEE ALSO:
Map Tools
251
Map Tools
The Map functions allow you to change the transparency of the image and/or convert to a full screen image view.
Each BLACKBOX image contained within the MAP represents an individual node within the Site. The Node (Elspec Node 1) that is highlighted in the Components section has a corresponding highlight on the MAP. The images can be placed anywhere on the background image (MAP) by simply dragging and dropping with the mouse.
SEE ALSO:
Maps
252
Notifications Viewer
The Notification Viewer is a tool for managing the notifications created by a site(s). Using this tool, you can manage multiple notifications simultaneously created by any Task that you requested to receive notifications for. You can also acknowledge multiple notifications.
253
Include attachments: Clicking on a specific line you can see the attachment in the attachments area (if the check box is checked). Select/Deselect: Right clicking the Notification entry allows you to select or de-select all notifications entries.
Please note the highlighted Notification entry appears in the right hand pane.
SEE ALSO:
254
255
Select/Deselect: Right clicking the Notification entry allows you to select or deselect all notifications entries. Select the button to Disable all the selected notifications not to receive the selected Pop-up Notifications:
SEE ALSO:
Notifications Viewer
256
Components
The PQSCADA software utilizes components to represent the physical location of devices or groups of devices. The Graphical User Interface of the application uses a tree-like file structure to Expand and Collapse the representation of the components. Components can also be imported from previous versions of PQSCADA and upgraded to be used in the current version. The main viewing area of the PQSCADA Graphic User Interface contains all of the Servers, Nodes and Sites. These are referred to as the components.
SEE ALSO:
257
Server
The PQSCADA server is the heart of the BLACKBOX data management and analysis system. See PQSCADA Server for more details. The following functions may be performed on the Server:
Connect to a Server or additional Servers Add a Server Delete a Server Configure a Server Copy a Link
258
Add A Server
In order to manually add a server(s), right click at " Server is Missing". The Add Server Dialog Box appears:
Select Database Engine: Identifies the database ending as an SQL type server SQL Express Install Button: Launches an automatic installation of the SQL server where most parameters are pre-configured. We recommend using SQL Express only for evaluation purposes. Only active if existing database is not recognized. Browser Button: Allows you to search for an available database server Engine Name: The name assigned to the server database engine User Name: The name of the user as defined for the database server (For SQL Express installed from the CD, the user name is sa) Password: User Defined (For SQL Express installed from the BLACKBOX CD, the password is PQSpqs12345).
259
Test Button: Will test & validate the connection in order to ensure that the details including the Password for the Database Engine are correct.
We recommend putting SQL on the Local Server; however you may access a remote database through the Network Server's tab. In order to add the database, double click the desired database (we are using an SQLEXPRESS database in our example).
Ensure that all the prerequisites Software Programs are installed prior to installing SQL Express You need to select the button, in order to run the full validation process. This is especially applicable in the event that you may have entered an incorrect password. As such the validation process will be incomplete & the PQSCADA system will prohibit you from performing certain actions.
SEE ALSO:
260
Connect to Server
PQSCADA V 4.1 & later versions features a support a connection to multiple servers.
In the main window select the Administration Console. Either right click select Connect to Server or select Connect to Server tab:
HTTP - Is the default method of communicating with the server. The software uses HTTP port 80 as the default port to communicate with the Node. HTTPS - Is the combination of the Hypertext Transfer Protocol (outlined above) with the SSL protocol to provide encrypted communication and secure identification of a network web server. See Encryption. net.pipe - Improves the connection in case that the server is a local connection. This option will speed up the http connection. Precise URL address of the Server. In this example the Url address for the HTTP connection is localhost/PQS. button.
Select
Should the test for the connection be successful, the message will appear:
261
Select
&
In order add additional servers, select the Administration Console. Connect to any other additional servers by simply selecting Connect to Server tab:
Follow the procedure outlined above using the Add Server dialog box When you have concluded the procedure, all the added servers will be displayed in the Components Column:
SEE ALSO:
262
Delete Server
Prior to deleting the server, you will need to Delete the Site(s) & Node(s). The server can then be deleted by simply selecting the Server (PQS Server in our example) Select Delete Server Database in the in the components window of the Administration Console:
Remove Database: This option allows you to retain or remove the existing database. Delete Base Folder: Allows you to retain or delete the base folder for the Server.
SEE ALSO:
263
Automatic Maintenance Enable Logger Shrinkage Security E-Mails SMS/Text Report Management
Right clicking on the Server (PQS Server in our example) or double-clicking on the Server itself will navigate you to the Server Configuration window & in default will open the General window:
You may allocate a new Server Name, or alternatively Select default settings click should you wish to revert to the factory .
264
Automatic Maintenance
Set the Automatic Maintenance settings by selecting the Automatic Maintenance Tab:
Enable Database Maintenance: If this is checked, then the operations below occur:
Re-Index: Each table in the database may have one or more indexes. After some time these indexes get fragmented which makes operation on the database take longer. Re-index reorganizes these tables and makes the database faster. Truncate Log: Each database works with 2 files; Data and log. If you are not doing SQL transactional backup, then you should turn this ON. Shrink Log: Truncate log only sets the log file to begin from the start but does not free up the log file space. Shrink log deletes all the unneeded information in the log file. Shrink Database: After some time the database gets fragmented (not disk fragmentation) or has data that is marked for deletion but is not actually deleted from the physical disk. This operation reorganizes the database file on the disk and makes the whole database operation faster. Remove Null Rows: This newly added operation automatically compacts database files with "null row values". Click to apply your changes, or/
265
SEE ALSO:
General About Configuring a Server Enable Logger Shrinkage Security E-Mails SMS/Text Report Management
266
Logger
PQSCADA 4.1 & later versions, now features setting an automatic log for database shrinkage. Enable the Logger Shrink by selecting the Logger Tab:
Enable Logger Shrink: enables you to set an automatic log either or, or both by
Shrink Logger By Time: Set periodic log to automatically compact the database. Shrink Logger By Rows: Set an automatic log according to number of rows within
to apply your changes, or/ should you wish to revert to the factory default click .
settings
SEE ALSO:
General About Configuring a Server Automatic Maintenance Security E-Mails SMS/Text Report Management
267
E-Mail
PQSCADA is capable of sending e-mail notifications from an E-Mail account. This section is to establish the specifics of the sender's account.
E-Mail Settings Proxy Settings Test the Settings by entering the applicable e-mail address click
to apply your changes, or/ should you wish to revert to the factory click .
SEE ALSO:
General About Configuring a Server Automatic Maintenance Enable Logger Shrinkage Security SMS/Text Report Management
268
SMS/Text
This section defines the configuration settings for a modem which will transmit an SMS/Text message.
Modem Settings Test the Settings by entering the applicable (Mobile # - without spaces or characters) click .
MODEM SETTINGS
The modem settings are pre-defined for communicating with the BLACKBOX device. Any of these settings can be changed at any time. If you experience difficulty after making any customized settings, you may revert to the factory default settings by selecting click . Restore Default Values
SEE ALSO:
General About Configuring a Server Automatic Maintenance Enable Logger Shrinkage Security E-Mails Report Management
269
Report Management
With PQSCADA V4.2.2.2 the PQS Server & Management Studio can be installed independently on two different computers. This increases the flexibility & accessibility of the PQSCADA 4.2. As part of this development the Report System is installed independently from the PQSCADA. This allows the user to effectively manage the reporting system of the entire network. Users simply select & install reports of relevance from any location. The Reports are installed separately from the PQSCADA Management Studio on Elspec's Website. In addition an automated installation is available on the BLACKBOX Disc (enclosed with every unit). After you have installed the new PQSCADA 4.2, you will need to install the new Reports. The following procedure describes the installation process. The installed reports of your choosing can be viewed on the Server's Configuration.
After you have opened the Server Configuration, Open the Report Path Tab:
270
, & in the dialog box add the new Folder Location in order to add the Path. The path will
Install the reports from the Preferred Location (As outlined above)
Click every time you installed a new report & the Installed
SEE ALSO:
General About Configuring a Server Automatic Maintenance Enable Logger Shrinkage Security E-Mails SMS/Text
271
Copy Link
This feature copies the URL link of the server directly into an Investigator application.
On the main viewing area in the Component Column select a Component right-click select Copy Link:
select
272
SEE ALSO:
273
Site - Description
The SITE is a software component (logical representation) of a physical location(s) which represent a group of Nodes (devices). The Server (Local Computer) is the representation of the physical machine (on which the PQSCADA server application is installed). The purpose of a SITE is to organize the Nodes by a common set of characteristics (i.e. location). For each monitored device, a Node must be created. All of the following can be performed on a Site:
274
Add Site
Right click the Server (PQS Server in our example), then select Add Site or select Add Site in the components window of the Administration Console.
This opens the Add Site window. All parameters are seen here for the existing SQL Server including user defined Username and Password (For SQL Express installed from the CD, the user name is sa and password is PQSpqs12345). Note the Set Defaults option will include the default settings of the Database Engine. The Save Settings box is selected which means that all parameters will be retained for all future sites added to this server. You are only prompted to enter a Name under Properties for the site in this window (it may be changed at any time).
275
Click
to conclude.
SEE ALSO:
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
276
Delete Site
Prior to deleting the site, you will need to Delete all the Node(s) within that site. Right click on any Site (PQS Site in our example) select Delete or select Delete Site in the components window of the Administration Console:
277
Remove Database: This option allows you to retain or remove the existing database. Delete Base Folder: Allows you to retain or delete the base folder for the Server. Select to conclude.
SEE ALSO:
278
Site - Configuration
Basic Configuration of the Site can be performed from the Site Configuration window:
select Configuration.
SEE ALSO:
279
Name Allocation
Name: The user defined name for the site (may be changed) Description: A user defined description for the site (not mandatory) Click to conclude or go on to the next step Image Selection
280
Image Selection
Image for Site: Here a user selected image can be imported from your local computer to represent each site. An icon of the BLACKBOX device is automatically placed on the background. This configuration parameter is used in conjunction with the Map feature. Check to clear image: This will remove the image and allow you to use a different image or none at all.
281
Node - Description
A Node is a logical representation of the physical device location that performs all of the following functions:
Retrieves and de-compresses the PQZIP files Parses and stores the data into the correct database. Calculates queries in real time.
282
Add Node
Individual or multiple Nodes can be added to Sites using the Add Node command. Alternatively you may add a server, site, and node using the component wizard in the Getting Started chapter.
Right click the Site (Elspec Site), then select Add Node or select Add Node in the components window of the Administration Console. This opens the Add Node window:
All parameters are seen here for the existing SQL Server including user defined Username and Password (For SQL Express installed from the CD, the user name is sa and password is PQSpqs12345). Note the Save Settings box is selected which means that all parameters will be retained for all future nodes to be added to this server. You are prompted to enter a
283
Note the GMT Offset where you set the local time in relation to Greenwich Mean Time (GMT). The browser button opens the Select Device dialog box which displays all devices on the LAN.
284
Multiple nodes can be selected by holding down the Ctrl key and clicking the left mouse button for each desired device(s):
Select
285
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
SEE ALSO:
286
Remove Node
Individual or multiple Nodes can be deleted from Sites using the Delete Node command.
Right click the Node (E Name in this example), then select Delete or select Delete Node in the components window of the Administration Console.
287
Remove Database: This option allows you to retain or remove the existing database. Delete Base Folder: Allows you to retain or delete the base folder for the Server. Select to conclude.
SEE ALSO:
288
Node - Configuration
Each Node can be individually configured to collect data from the device according to pre-set parameters and settings. There are the following configurable parameters for Node configuration.
General Configuration Device Configuration Download Schedule Configuration Configure Parameters Folders Configuration Database Configuration
Double-click on the Node to open the Node Configuration window directly, or alternatively right-click the Node (Elspec Node in our example), then select Configuration:
SEE ALSO:
289
General
After Configuration has been selected the Node Configuration window will open.
Enter:
Name: A user defined name for the node (device) Description: A user defined description for the node (device). GMT Offset: The local time established for recording in relation to Greenwich Mean Time (GMT).
SEE ALSO:
Node Configuration Device Configuration Download Schedule Configuration Configure Parameters Folders Configuration Database Configuration
290
Device
After Configuration has been selected the Node Configuration window will open.
Enter:
IP Address: Enter the IP address of the device or use the search window browser. User Name: Each device is shipped with a default user name (ftpuser) as above. This name corresponds to the FTP login name set in the firmware of the device (Access Setup section). If you wish to change the user name here, then it also must be changed in the firmware. Password: The password corresponds to the user name above. It should be changed according to the device password. (The default password as shown above is ftppassword). Device PQZIP Folder Path: The specific path where the PQZIP folders are stored on the device. We do not recommend changing this setting. FTP Protocol: The default setting is Passive. Select to complete the Device Configuration.
SEE ALSO:
Node Configuration General Configuration Download Schedule Configuration Configure Parameters Folders Configuration Database Configuration
291
Download Schedule
After Configuration has been selected the Node Configuration window will open.
ENTER:
Periodic Time to Get File: This is a user defined setting to determine the interval of time to retrieve the PQZIP file(s) from the device. If multiple files exist, this setting is not relevant and there will be no delay. Download Schedule: The specific days and times to perform the file retrieval. Limit Download Time Range: Specifies which files are downloaded that meets a specific date criteria. Enabling this parameter will exclude files that do not fall in the specified time range. File Download Mode: This is a factory setting that should not be changed. Select to set the Download Schedule.
SEE ALSO:
Node Configuration General Configuration Device Configuration Configure Parameters Folders Configuration Database Configuration
292
Parameters
After Configuration has been selected the Node Configuration window will open.
Configure the Parameters for this Node by selecting the Parameters Tab:
By default, only Cycle by Cycle Waveform is selected. The selection is not permanent therefore you may add more parameters in the future and may recalculate with new parameters.
click
293
Definition
RMS Voltage/Current. HRMS Voltage/Current. THD Voltage/Current. Crest Factor Voltage/Current. K-Factor Current. U1 - Positive Sequence Voltage/Current. U2 - Negative Sequence Voltage/Current. U2/U1 Voltage/Current. U0/U1 Voltage/Current. Active Power Reactive Power Apparent Power Power Factor Frequency 200ms (Device frequency) Waveforms Cycle by Cycle Frequency
Voltage Harmonics Current Harmonics Active Power Harmonics Reactive Power Harmonics Fundamental Harmonics Harmonics Only Fundamental Only Frequency Frequency Cycle by Cycle Including
Power
Low
Low
Statistics
Low
High
294
IEC61000-4-30
Definition
IEC61000-4-30
Current
RMS Current HRMS Current THD Current Crest Factor Current U1 - Positive Sequence Current U2 - Negative Sequence Current U2/U1 Current U0/U1 Current Over Deviation Current Under Deviation Current Spectrum Voltage Spectrum Current (Only if Current is selected) Inter-Harmonics Voltage Sub-Group
High
Low
Inter-Harmonics
High
High
Inter-Harmonics Sub-Group Current (Only if Current is selected) Inter-Harmonics Angle (Only if Current is selected) Inter-Harmonics Phasors (Only if Current is selected)
295
IEC61000-4-30
Definition
Harmonics
Voltage Harmonics Current Harmonics (Only if Current is selected) Active Power Harmonics Reactive Power Harmonics Non-Standard Parameters (Only if Current is selected) Fundamental Including Harmonics (Only if Current is selected) Harmonics Only (Only Current is selected) if
Medium
Low
Medium
Low
Fundamental Only (Only if Current is selected) Frequency 3 sec. Aggregation Frequency Aggregation at 10 min. & 2 Hours Medium High
Aggregation
Definition
Frequency Statistics RMS Statistics THD Statistics Active Power Statistics Reactive Power Statistics Apparent Power Statistics Power Factor Statistics
296
SEE ALSO:
Node Configuration General Configuration Device Configuration Download Schedule Configuration Folders Configuration Database Configuration
297
Folders
After Configuration has been selected the Node Configuration window will open.
Incoming Folder Size Limit: The size of the temporary folder where the PQZIP files are stored while they are waiting to be processed. The default is 2 GB, although this can be changes according to your available system resources. All original PQZIP files are deleted after they are processed unless they are backed up. Backup Folder Size Limit: To enable this feature, check the Backup Folder Size Limit check-box. This sets the size of the backup folder where all good PQZIP files can be archived. When the file folder reaches its limit, the oldest files will be deleted first. Bad Files Folder Size Limit: The size of the bad file folder where all bad PQZIP files are kept. A file status (good or bad) is determined when the file is processed. Set the desired Folder Size Limits click .
SEE ALSO:
Node Configuration General Configuration Device Configuration Download Schedule Configuration Configure Parameters Database Configuration
298
Database
After Configuration has been selected the Node Configuration window will open.
Allow Truncate Data Automatically: Enabling this feature allows the Node to truncate older data once the database size limit is reached. Limit Data Size in Database: Enabling this feature limits the amount of data in the database to the specified amount. If this limit is reached and "Auto truncate" is not enabled, then the Node won't parse any Node files until data is deleted manually. Limit Aggregated Data Time in Database: Enabling this feature limits the amount of data in the database to the specified time duration. If this limit is reached and "Auto truncate" is not enabled, then the Node won't parse any Node files until data is deleted manually. Set the desired Database Size Limits click .
SEE ALSO:
Node Configuration General Configuration Device Configuration Download Schedule Configuration Configure Parameters Folders Configuration
299
Device IP
By right clicking the device in the Device IP Column allows you to:
Open the Web Browser Open the FTP Site containing the PQZIP files on the device Change the IP Setup or other Configuration parameters for the device
300
Open In
The Open Function has two purposes:
It allows you to enter the FTP Site where all PQZIP files are stored. This option allows you to manually download the files:
301
Component Functions
The Graphical User Interface of the application uses a tree-like file structure to the representation of the Components. Components can also be imported from previous versions of PQSCADA and Upgrading to be used in the current version. The component functions can be broken down as follows:
Common Functions (Functions that are relevant for all components (Expand, Collapse, Upgrade, and Moving Components) Specific Functions:
Server (Only relevant for the server) Site (Only relevant for the site) Node (Only relevant for the node)
302
Collapse
Components such as the Server and Site can be made to view more easily by collapsing the component tree. This is accomplished by:
Clicking the (-) sign next to the component (PQS Server in this example):
To collapse only to the 1st Level, right click the desired component, then select Collapse:
303
Expand
Components such as the Server and Site can be viewed to reveal sub-components quite easily by expanding the component tree. This is accomplished by:
Clicking the (+) sign next to the component (PQS Server in this example):
select Expand:
304
Moving Components
The PQSCADA software offers a user friendly hierarchical Site construction view. A very large Site can be broken down into smaller sub-Sites. In each Sub-Site, it is possible to create Sub-Nodes. In this way, the structure and GUI of the Main viewing area in PQSCADA most accurately represent the actual electrical grid architecture. The PQSCADA allows you to change the logical location of Nodes and Sites with drag and drop convenience, to parallel a physical change. It is possible to move entire Sites underneath other Sites as well as moving individual Nodes to other Sites as well as other Nodes.
Moving Components: This is done very simple by clicking the component with the left mouse button, then by dragging it to the new location. You will only be able to do this by Unlocking your components - see Administration Console for more details.
SEE ALSO:
TUTORIAL DEMONSTRATION:
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system.
305
Upgrade Components
We recommend that you upgrade all sites and nodes together for each server; however you may choose to upgrade individually as well. As shown below Elspec Site and Elspec Node appear but are not yet upgraded or active.
To upgrade all sites and nodes for a server, right click the server (PQS Server in our example), then select Upgrade:
The Site (Elspec Site) and Node (E Name) have been upgraded and now appear under PQS Server:
SEE ALSO:
306
Encryption About
PQSCADA V4.1 & later versions supports the SSL protocol (Secure Socket Layer) for enabling secure, encrypted communication between PQSCADA Management Studio and Investigator which are both client software, and the PQSCADA Server. Furthermore, the certificate can also provide proof of the servers identity should the administrator choose to purchase and install a commercial certificate from a trusted CA. This is in addition to the newly added Security Module & may be used independently or in combination with this module. In order to enable encrypted communication, please follow the steps as they are listed below:
Installing the SSL Certificate Binding the Certificate Configuring PQSCADA to use SSL Change the Communication Binding
SEE ALSO:
Security Module
307
& R)
type MMC
Enter
A MMC window will open. Press Ctrl+M, and the Add or Remove Snap-ins window will appear. Double-click Certificates:
In the Certificate Snap-in window, select Computer Account select Local Computer :
select
308
right-click Personal
309
on the first
page Browse on the second. You will need t o browse to PQSCADAs installation directory, and select the PQS Authority.pfx file:
On the next page, you will be asked to supply a password for the private key. The password is PQSpqs12345:
310
Select
twice
SEE ALSO:
About Encryption Binding the Certificate Configuring PQSCADA to use SSL Change the Communication Binding Security Module
311
Follow the following steps: 1. Open a Command Prompt window 2. Type httpcfg query ssl Enter
3. If the result is Empty, meaning that no certificate is currently binded to port 443 & you may therefore proceed directly to Step 4. Should a certificate be already binded to port 443, verify whether or not it is needed. If not, you may remove it by entering the following (replace the relevant section in the command with the Thumbprint of the current certificate):
httpcfg delete ssl -i 0.0.0.0:443 -h <the thumbprint of the current certificate> The result should read code 0.
4. In order to Bind the SSL Certificate to Port 443 type the following:
3. If the result is Empty, meaning that no certificate is currently binded to port 443 & you may therefore proceed directly to Step 4. Should a certificate be already binded to port 443, verify whether or not it is needed. If not, you may remove it by entering the following (replace the relevant section in the command with the Thumbprint of the current certificate): netsh http delete sslcert ipport=0.0.0.0:443
4. In order to Bind the Server's Certificate with Port 443 type the following:
312
netsh http add sslcert ipport=0.0.0.0:443 certhash=0d64dfe8ce0498450c5a52eb9f73f52c7bafc595 appid={000000000000-0000-0000-000000000000} clientcertnegotiation=disable Go on to the next step Configure PQSCADA to use SSL
SEE ALSO:
About Encryption Installing the SSL Certificate Configuring PQSCADA to use SSL Change the Communication Binding Security Module
313
SERVER:
Go to the appSettings section, locate the key named IsHttpsEnabled & change the value attribute to true (the default is false):
314
In the event that you purchased a commercial certificate from a trusted CA, you will need to follow these additional steps:
Locate the serviceBehaviors section & change the existing certificate Thumbprint in the two locations:
After this change the PQS Service needs to be restarted once again. Proceed to the next step Change the Communication Binding
SEE ALSO:
About Encryption Installing the SSL Certificate Binding the Certificate Change the Communication Binding Security Module
315
: :
316
Low: Ignores any errors which may occur due to an invalid certificate. Medium: Warns when an invalid certificate is being used, & prompts the user to acknowledge. High: Requires a valid certificate & will not proceed if it is not present.
SEE ALSO:
About Encryption Installing the SSL Certificate Binding the Certificate Configuring PQSCADA to use SSL Security Module
317
TYPES OF SUPPORT:
Networks of PQSCADA Servers & each one refers to a Primary Security Server within that Network:
318
This is a more commonly used environment, where a single server acts as the Primary Security Server:
This scenario the client may connect to multiple PQSCADA networks each with 1 pre-defined Primary Security Server. The client initiates a user authentication, the direct server forwards the request to the Primary Security Server, which performs the actual validation.
319
TERMS:
Term Admin Definition This is the System Administrator (Full permissions to perform any action) User with certain Administrator privileges (Full Permissions forget, safety & set operations) Common User (Lowest Permission to view data only)
Operator
Viewer
STEPS:
The following steps are performed either by the Admin &/ Operator &/ Viewer within the Security Module:
\
Enable the Security Module Locally (Admin) Define the Primary Security Server (local / remote) (Admin) Login to the PQSCADA Network (Admin, Operator & Viewer) Learn About User Accounts (Admin) Create & Add New User Accounts (Admin) Change User Accounts (Admin)
SEE ALSO:
About Encryption
320
Enable Security enter the relevant User admin) & Password (system default
321
SEE ALSO:
About Encryption Define the Primary Security Server (local / remote) (Admin) Login to the PQSCADA Network (Admin, Operator & Viewer) Learn About User Accounts (Admin) Create & Add New User Accounts (Admin) Change User Accounts (Admin)
322
DEFINING A BASIC ENVIRONMENT WITH ONLY A SINGLE SERVER (LOCAL SERVER OPTION):
This is a local Server that will authenticate the user's requests & will return the relevant data accordingly.
DEFINING A PQSCADA NETWORK ENVIRONMENT WITH SEVERAL SERVERS (REMOTE URL OPTION):
All other servers within this PQSCADA network stores the URL for this Primary Security Server, & interacts with the server that is responsible for returning the users relevant details.
Procedure:
Activate the Security Module Locally as per previous step. Define the Primary Security Server by either choosing a:
Local Server (Single Server) Remote URL (Network of PQSCADA Servers) by entering the Server's URL or searching for the server by clicking on the button: (ONLY SERVERS ADDED TO THE PQSCADA & SERVERS WITH THE LOCAL SECURITY ENABLED WILL APPEAR IN THE "REMOTE PRIMARY SECURITY SERVER SELECTION" WINDOW)
323
button
click
click
By selecting "Password Must Meet Complexity Requirements" option will set the required length for the password at 8 characters . click
SEE ALSO:
About Encryption Enable the Security Module Locally Login to the PQSCADA Network (Admin, Operator & Viewer) Learn About User Accounts (Admin) Create & Add New User Accounts (Admin) Change User Accounts (Admin)
324
In the User Login Dialog Box enter the applicable User name & Password, select Login:
The Remember Credentials option allows you to save the login details for a faster login action.
SEE ALSO:
About Encryption Enable the Security Module Locally Define the Primary Security Server (local / remote) (Admin) Learn About User Accounts (Admin) Create & Add New User Accounts (Admin) Change User Accounts (Admin)
325
There are three types of pre-defined User Accounts that permits / denies users to perform certain actions. The Admin allocates the type of permission when Creating & Adding New Users within these three groups. The table below outlines the type of User Accounts including their relevant Permissions.
Viewer
Operator
Admin
Site Log Request Components Node Add Node Delete Node Node Log Request
326
Components General Upgrade Refresh Component View Notifications Attach /Detach Component Update Component Update Components On Map Location Enable/Disable Service Modify DB Connection Disable Notifications Tasks & Templates Add Task Modify Task Delete Task Rerun Task Stop Task Add Template Modify Template Delete Template
327
Database Re-Index Add Factor Parameters Force File Parse Attempt Recalculate Data Swap Phases Delete Data Security Add User Modify User Delete User User Manager Enable Security Set Primary Security Server Report Management System Add Reports Folder Path Remove Report Folder Path Refresh Reports
328
General Reset PQZIP Files Refresh View Notifications View Database Report FTP Force Connection Remove Log Entries Task Log
select User
329
The Table below describes all the Components within the module: Description
Component
with
Servers, Sites & Nodes Connected within the selected Primary Security Server Access to Wizard Add User
Access to Delete User Wizard Access to Change Password Wizard Refresh Button Apply Changes Button
330
SEE ALSO:
About the Security Module Enable the Security Module Locally (Admin) Define the Primary Security Server (local / remote) (Admin) Login to the PQSCADA Network (Admin, User & Administrator) Change User Accounts (Admin)
331
Select
select
332
Select the relevant Components) you wish to provide access to the user. Assign the applicable permission by selecting the component, right-click select (Viewers / Operator) select to go on to the next step:
A Summary will follow including all the new user's details. Select either to conclude or to make any changes:
The User Manager will now appear including the Newly Added User, Access To Components with Permission Type:
333
Once a user has been added, the administrator can make the following Changes to the User Accounts:
Change User Details, Add / Change Components, Change Permissions, Delete a User or Change the User's Password
SEE ALSO:
Enable the Security Module Locally (Admin) Define the Primary Security Server (local / remote) (Admin) Login to the PQSCADA Network (Admin, User & Administrator) Learn About User Accounts (Admin) Change User Accounts (Admin) Encryption
334
Change User Details Add / Change Components for Users Change User Permissions Delete Users Change User Passwords
Change the User's First & Last Name by selecting the user & retyping the new details within the relevant text box field:
Change Permissions by selecting the component followed by selecting the relevant User Account:
Once you have made the needed changes, select followed by a success message:
, it will be
335
Notify the user of the changes & it will be taken into effect once you have logged out/in to the server.
To Delete a user select the relevant user in the user group column select boxes: followed by twice in the two message
To Change a User's Password select the relevant user in the user group column box select followed by & complete the relevant password in the dialog :
336
SEE ALSO:
Enable the Security Module Locally (Admin) Define the Primary Security Server (local / remote) (Admin) Login to the PQSCADA Network (Admin, User & Administrator) Learn About User Accounts (Admin) Create & Add New User Accounts (Admin) Encryption
337
Tool Tips
The tool tips provide you with real time information when you pass the mouse over each respective column for:
338
SEE ALSO:
About Tool Tips Device Tool Tips Download Status Tool Tips Data Processing Tool Tips Compliance Tool Tips Database Tool Tips
339
Web Browser:
SEE ALSO:
About Tool Tips Component Tool Tips Download Status Tool Tips Data Processing Tool Tips Compliance Tool Tips Database Tool Tips
340
Data Downloading has been Enabled/Disabled Data Scanning Status - See Node Download Schedule Real time status and specifics of the file being downloaded Downloading speed Original creation date/time of the PQZIP file Device Disconnected
SEE ALSO:
About Tool Tips Component Tool Tips Device Tool Tips Data Processing Tool Tips Compliance Tool Tips Database Tool Tips
341
SEE ALSO:
About Tool Tips Component Tool Tips Device Tool Tips Download Status Tool Tips Compliance Tool Tips Database Tool Tips
342
SEE ALSO:
About Tool Tips Component Tool Tips Device Tool Tips Download Status Tool Tips Data Processing Tool Tips Database Tool Tips
343
SEE ALSO:
About Tool Tips Component Tool Tips Device Tool Tips Download Status Tool Tips Data Processing Tool Tips Compliance Tool Tips
344
Video Demonstrations
We have created the following collection of Flash Video Tutorial Demonstration(s) that may be opened with Internet Explorer or any flash player available on your system:
345
ADDING A SITE:
Adding a Site guides you through a step-by-step process of adding a Site to a Server.
ADDING A NODE:
Adding a Node guides you through a step-by-step process of adding Node(s) onto Sites.
MOVING COMPONENTS:
Moving Components guides you through the process of changing the logical location of Nodes and Sites with drag and drop convenience, to parallel a physical change. It is possible to move entire Sites underneath other Sites as well as moving individual Nodes to other Sites as well as other Nodes.
346
Troubleshooting
Component
SQL Installation
Issue
During the SQL Express installation, the PQSCADA did not recognize the Windows installer 4.5 is for Arabic Vista SP2 You receive an error message: Installation error #1001 during Installation.
Reason
Solution
Install SQL Express RS2008 directly from the BLACKBOX Disc supplied with the product & not via the PQSCADA
PQSCADA Installation
In order to ensure that the PQS Service is complete uninstalled, you will need to re-run the procedure via your Run box in your Start menu: Click Start Run CMD In the command prompt window, type sc delete pqs.server Enter Restart your computer & Re-install new PQSCADA version. NOTE NOTE NOTE Open the command prompt for Windows Vista/7 with elevated permissions
You receive an error message: PQSCADA Server can only be installed for one user only
PQSCADA Server is already installed for one user & you need to therefore only install the PQSCADA.
During the Installation procedure for Select Components select only the PQSCADA Management option:
347
Component
Notifications Viewer
Issue
Notifications are not displayed in the Notifications Viewer You don't receive any notifications further the Notification Task you've created.
Reason
You didnt select the Start & End-Time range when you configured your Notifications Viewer. You have created a Site under a Node. Therefore the PQSCADA is unable to recognize a task created under two Sites.
Solution
You will simply need to simply select the time range again: Follow the Notifications Viewer procedure Create only 1 Site for Node(s):
Notification
VDC Query
The PQZIP file for the G3500 doesnt support the VDC parameter.
You need to set this configuration in the Device's Web Interface: From Elspecs Search Utility open your G4K unit the Web Interface, In Configuration uncheck the VDC parameter
FTP
Once the PQSCADA has downloaded the PQZIP files from the G4K Unit, it will keep a list of all the files & folders in order to ensure that the re-downloading process is not duplicated. In some rare instances (for example when the PQZIP files are deleted from the G4K), the PQSCADA doesnt always recognize the availability of additional folders & ceases the process.
You will simply need to prompt the PQSCADA to rescan & download these files again: Follow the Rescan Device Folders procedure
348
Component
FTP - Continue
Issue
The Node keeps on downloading the same PQZIP file without advancing to the next download. (You may confirm this, by accessing your Log Viewer See the Help Wizard: Troubleshooting Viewer). Log
Reason
The folder, under which the PQZIP file in question is located, contains PQZIP files with indexes bigger than the limit of an integer.
Solution
You will need to change the index of the problematic files: Open the Node in the FTP Locate the problematic files Simply change the files to a smaller number than the limit (Right-click Rename the File)
PQZIP
You are unsuccessful in redownloading the PQZIP files appear as errors in the Log Viewer
When the PQSCADA downloads and calculates PQZIPs, the processed files are saved in the Database. Re-downloading the files (e.g. in case some data was deleted from the node), will result in an error in the logger that these files have been already downloaded. The PQ configuration in the Web Interface for the G4K unit reads as Misconfigured: The state of the device is not no DSP sync. Invalid time synchronization has been configured in the Web Interface.
You will need to reset the PQZIP files for that Node: Follow the Reset PQZIP File procedure
Make sure that PQ Configuration is correct in the Web Interface: Configuration Configuration Voltages & Frequency Currents
Differences there could affect the data recording In the Web Interface enter: Configuration Time
For SNTP Usage: Ensure you to have a valid IP address of the SNTP For GPS Usage: With PPS or IRIG-B for the time sync (and the device jumps between SNTP and the GPS\IRIG-B) change the Transport field to GPS only
349
Component
PQZIP Continue
Issue
The recorded data is incomplete (some of the data is missing)
Reason
PQZIP files are finalized too fast & therefore the PQZIP files are undersized In the Web Interface enter: Configuration
Solution
PQZIP Recording
Change the PQZIP file size to 2 hours PQZIP files are not finalized properly and remain as PQ files. The PQSCADA application cannot download incomplete files. To make sure that this is the case go to the FTP root folder and verify that the time stamp in PQ files is similar to the time stamp of the missing data. PQZIP files are transferred to the Bad Files Folder PQZIP Task PQZIP Task has failed to create PQZIP files PQZIP files are limited to a file size limit of 2Gb. Should some or all the PQZIP File not be finalized: In the Web Interface, Disable the PQZIP recording Go to the FTP root folder and delete all PQ files. In case there are only few files that were finalized improperly and the missing data is important send the files to Elspecs Software Support. Send the files to Elspecs Software Support for further investigation. You need to re-perform the PQZIP Task for either a shorter period of time / alternatively, with a less amount of data: Follow the Add A General Export Task procedure
350
Component
PQZIP Viewer
Issue
PQZIP file cannot be opened by PQZIP viewer in Vista or windows 7 OS.
Reason
The user account control settings (UAC) is on.
Solution
You need to turn off the user account control settings (UAC) on your computer: From your Control Panel select Change User Account Control Settings:
Set the settings to Never Notify Components Your attempt to add components have been unsuccessful. Components adding consist of events sequence and some of them were not executed as the PQSCADA Service was halted / interrupted or the computer was reset. Follow Remove & Create Node procedure in order to delete & create the node once again
351
Component
Server
Issue
PQSCADA management studio doesnt respond
Reason
Either the SQL Server is down or there is an error in the Network.
Solution
In the PQSCADA Stop and Start the PQS Service:
You are unable to perform certain actions in the PQSCADA management studio
You have entered an incorrect password when you Connected to the Server. Or the
You need to reconnect to the Server Disconnect from the Server (Select the Server in question click select Disconnect ) right-
352
Component
Parameters
Issue
Elspec's Investigator Program does not show the data with a resolution above 2.5 hours.
Reason
The parameters were not checked during the configuration of the node & consequently they were not calculated.
Solution
From the Parameters mark the specific parameters to be calculated Or alternatively Follow the Recalculate Data procedure
The G4K device was configured incorrectly during installation & setup & recorded the data incorrectly. Therefore phases need to be swapped (polarity) to correct the data calculation. You may have a MSI Security problem
Reports
You need to create the following folders on your computer: For 64-bit (x64), create this folder: C:\Windows\SysWOW64\config\systemprofile\Desktop For 32-bit (x86), create this folder: C:\Windows\System32\config\systemprofile\Desktop
The data in report produced from the PQSCADA differs from the data produced in Investigator.
353
Component
Tasks/Reports
Issue You are unable to see your previous Report Tasks PostSystem Upgrade.
Reason
Solution
If you haven't already done so, prior to Installing PQSCADA 4.2 & later versions, PQSCADA 4.2, ensure that you backup your Database in support a new Report System that is installed independently after you order not to lose previous data, have installed the new PQSCADA V4.2.2.2. All tasks related to report tasks, therefore needs to be If not, you'll need to re-configure your Report Tasks re-configured from anew. from anew.
Daylight Savings Time is currently not supported & therefore subsequent changes will not be calculated.
Tasks / Reports configured with daylight savings time, displays different data than expected. Performance The PQSCADA client is functioning slower than usual.
Simply Reduce / Increase the time range according to your specific time difference.
The system is not responding & freezes even after the PQS Services has been stopped / restarted.
You need to change your preferences back to the factory default settings
Select
to
Display
354
Log Viewer
The Log Viewer enables you to see specific information related to log entries with varying levels of importance:
Filter By:
Debug: By default this option is disabled & it is used only by an Elspec Software Technician. Info: Will include general information on actions taken in PQSCADA. In addition, it will also include Warnings, Error & Critical entries. Warning: Will include any malfunctions that the PQSCADA will resolve by itself. The log will also include any Errors & Critical entries. Error: Includes malfunctions that the PQSCADA was unable to resolve. For example failed Tasks due to an incorrect E-Mail address. See Troubleshooting. The log will also include any Critical entries. Critical: Contact Elspec or your local representative.
# of Last Entries: This function will enable you to extract only the desired number of Last Entries from the vast amount of all the recorded data, allowing you to focus on the latest relevant data. Start / End Date & Time: Select Start Date & Time option, should you wish to filter by a different date & time Include Keywords into your search
355
356