Está en la página 1de 3

Product Data Sheet Edition 11, 2006 Version no. 08.

06

Sika Injection-20
PUR injection resin
Product Description
Highly expansive solvent-free water-reactive two part polyurethane foam injection system with long potlife. Sika Injection-20 is used for stopping water infiltration and to be injected into water filled cracks To achieve permanent watertight crack sealing, subsequently inject Sikadur-52 Type N or Type LP, Sika InjectoCem-190 or Sika Injection-29 New (VP) Characteristics / Advantages A special characteristic of this product is that no reaction takes place unless it is in direct contact with water / moisture The foaming rate in contact with water is dependent on the available water quantity Sika Injection-20 can be injected with a single component pump

Construction

Uses

Product Data
Form Colours Part A: Part B: Part A+B mixed: Part A: 9.00 kg Part B: 1.00 kg Storage Storage Conditions / Shelf-Life 24 months from date of production if stored in unopened, undamaged original sealed packaging, in dry conditions at temperatures between +5C and +30C. Brown Light yellow Brownish

Packaging

Pre-measured 10 kg units (A+B):

Technical Data
Chemical Base Density Viscosity Solvent free water reactive two part polyurethane Part A: 1.14 kg/l (at +20C) Part B: 0.97 kg/l (at +20C) Part A: Part B: ~ 150 mPas (at +25C) ~ 5 mPas (at +25C) (at +20C) (at +10C) (at +5C)

Part A+B mixed (9 : 1): ~ 180 mPas Part A+B mixed (9 : 1): ~ 380 mPas Part A+B mixed (9 : 1): ~ 600 mPas

SikaPP Injection-20

1/3

System Information
Application Details Consumption / Yield Application Conditions/ Limitations Substrate Temperature Ambient Temperature Application Instructions Mixing Mixing ratio / reaction time
Mixing ratio by weight Sika Injection-20 A Sika Injection-20 B Induction* (sec.) Reaction* (sec.) Density after free expansion* Foaming rate* *A+B are mixed with 10% water

1 kg of Sika Injection-20 forms ~ 50 l foam (with free expansion in contact with water).

+4C min. / +35C max. +4C min. / +35C max.

+20C 100 10 20 75 20 100 15 15 55 20 55 100 20 10 45 20 100 10 25 90 20

+10C 100 15 20 70 20 55 100 20 13 55 20 100 10 35 100 20

+4C 100 15 25 80 20 55 100 20 15 60 20

Mixing Time Application Method / Tools Cleaning of Tools

Add both parts in the correct proportion to a suitable clean and dry container and stir slowly (max. 250 rpm) for at least 3 minutes until the mixture is homogeneous. Injection pump for single component products, such as Aliva AL-1200 or AL-1250.
. Clean all tools and application equipment with Sika Colma-Cleaner from polyurethane residue immediately after use. Hardened/cured material can only be mechanically removed.

Potlife Notes on Application / Limitations

Part A+B mixed without contact with moisture/water: ~ 6 hours (at +20C) The waterproofing process is divided into three phases: Injection: The time during which the injected material under pressure flows from the pump to the desired moisture/water containing areas. Induction: The time from mixing until reaction starts. Reaction: The period during which the mix viscosity increases and foam expansion takes place. Sika Injection-20 is generally used for stopping water infiltration fast. To achieve permanent watertight crack sealing, the subsequent injection of Sikadur -52 Type N and Type LP, Sika InjectoCem-190 or Sika Injection-29 New (VP) is recommended.

Value Base Local Restrictions Health and Safety Information

All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control. Please note that as a result of specific local regulations the performance of this product may vary from country to country. Please consult the local Product Data Sheet for the exact description of the application fields. For information and advice on the safe handling, storage and disposal of chemical products, users should refer to the most recent Material Safety Data Sheet containing physical, ecological, toxicological and other safety-related data.

SikaPP Injection-20

2/3

Legal Notes

The information, and, in particular, the recommendations relating to the application and end-use of Sika products, are given in good faith based on Sika's current knowledge and experience of the products when properly stored, handled and applied under normal conditions in accordance with Sikas recommendations. In practice, the differences in materials, substrates and actual site conditions are such that no warranty in respect of merchantability or of fitness for a particular purpose, nor any liability arising out of any legal relationship whatsoever, can be inferred either from this information, or from any written recommendations, or from any other advice offered. The user of the product must test the products suitability for the intended application and purpose. Sika reserves the right to change the properties of its products. The proprietary rights of third parties must be observed. All orders are accepted subject to our current terms of sale and delivery. Users must always refer to the most recent issue of the local Product Data Sheet for the product concerned, copies of which will be supplied on request.

Construction
Sika Egypt for Construction Chemicals El Abour City 1st industrial zone (A) Section # 10 Block 13035, Egypt

Tel :+202- 6100714/15/16/17/18 Fax :+202- 6100759 Mob :+2012- 3908822/55 www.sika.com.eg SikaPP Injection-20 3/3

También podría gustarte