Documentos de Académico
Documentos de Profesional
Documentos de Cultura
EXTRA
RAM: als de router aanstaat wordt config hier bijgehouden (run)
NVRAM: kopie van config bestand (bij spanning loss, blijft fit bewaard) (start)
!!! doe je niet copy run start, dan worden wijzigingen niet bewaard wanneer je
herstart !!!
Module 3: Een router configureren
3.1 Een router configureren
3.1.1 CLI (Command Line Interface)
Router>enable van user-modus naar privilege-modus gaan
Router#conf t naar de configuratie modus gaan (configure terminal)
Router(config)# = dit is de globale configuratie modus met hieronder de
specifieke configuratie modi.
Router(config)#hostname Tokyo
Tokyo(config)#
Router(config)#line console 0
Router(config-line)#login
Router(config-line)#password cisco
Router(config-line)#exit
Router(config)#
Het TELNET wachtwoord instellen: dat wordt gevraagd als je wil werken
via het netwerk/internet op deze router. (wachtwoord is cisco)
Router(config)#line vty 0 4
Router(config-line)#login
Router(config-line)#password cisco
Router(config-line)#exit
Router(config-line)#enable secret class (PRIVILEGE-modus)
Router(config)#
Router(config-if)#exit
4) configuratie aanpassen
Router(config)#no ... no configuratie commando
Router#copy start run terug originele configuratie uit
NVRAM halen naar RAM.
Router#copy tftp run configuratie van TFTP server
halen.
Router#erase start verwijdert de NVRAM versie (*)
reload start router opnieuw op ( na *
doen)
Router(config-if)#exit
Router(config)#interface e 0
Router(config-if)# description Engineering room 24b
Voer telnet of ping commando in, gevolgd door de naam van de router.
Extra: uitleg
Router# show ip route
C: direct verbonden (direct connected)
I: geleerd via IGRP
R: geleerd via RIP
Debug
Passwords
Router(config)# enable secret class : password for priv.mode if
passw. encryption is on
Router(config)# enable password cisco : password for priv.mode if
passw. encryption is off
Console
Router(config)#line console 0 : console 0
Router(config)#login
Router(config)#password cisco : console password
telnet
Router(config)# line vty 0 4 : configure telnet
Router(config)# login
Router(config)# password cisco : telnet password
Banner
Router(config)# banner motd #message#
Interfaces
Router(config)#interface s0/0 : for 2600
Router(config-if)# ip addres (adres) (subnet)
Router(config-if)# no shutdown
Router(config-if)# clock rate 56000 : only if DCE, not for DTE!
Router(config-if)# exit
Router(config)#interface e0/0
Router(config-if)# ip addres (adres) (subnet)
Router(config-if)# no shutdown
Router(config-if)# media-type 10Base-T :set media type
Routing protocols
Router(config)# router rip
Router(config)#network 192.5.5.0 :(networkpart of the addres)
Router(config)#network …
Checking
Router# sh run : show running config
Router# sh start : show startup config
Router# sh cdp neighbors
Router# sh ip route
Router# debug ip rip
Router# ping
Router# trace
Module 5: Cisco IOS software beheren
5.1 Router boot sequence en verifcatie
5.1.1 Stappen wanneer de router opstart
6) Test de hardware van de router
7) Zoek en laad de Cisco IOS software.
8) Zoek en pas de configuratie toe, inclusief protocol functie en interface
adressen.
Router(config)#line console 0
Router(config-line)#login
Router(config-line)#password cisco
Router(config-line)#exit
Router(config)#
Het TELNET wachtwoord instellen: dat wordt gevraagd als je wil werken
via het netwerk/internet op deze router. (wachtwoord is cisco)
Router(config)#line vty 0 4
Router(config-line)#login
Router(config-line)#password cisco
Router(config-line)#exit
Router(config-line)#enable secret class (PRIVILEGE-modus)
Router(config)#
Router(config-if)#exit
6) configuratie aanpassen
Router(config)#no ... no configuratie commando
Router#copy start run terug originele configuratie uit
NVRAM halen naar RAM.
Router#copy tftp run configuratie van TFTP server
halen.
Router#erase start verwijdert de NVRAM versie (*)
reload start router opnieuw op ( na *
doen)
Router(config-if)#exit
Router(config)#interface e 0
Router(config-if)# description Engineering room 24b
Voer telnet of ping commando in, gevolgd door de naam van de router.