Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Table of Contents
1General Information 1.1 TV-Certification 1.2 Hose Construction/ Hose Nomenclature 1.3 Product Overview 2 Hose Data Sheets 2.1 Inner Diameter 3 mm 0.11 inch 1/8 2.2 Inner Diameter 4 mm 0.15 inch 1/8 2.3 Inner Diameter 5 mm 0.19 inch 3/16 2.4 Inner Diameter 6 mm 0.23 inch 1/4" 2.5 Inner Diameter 8 mm 0.31 inch 5/16 2.6 Inner Diameter 10 mm 0.39 inch 3/8 2.7 Inner Diameter 13 mm 0.47 inch 1/2" 2.8 Inner Diameter 16 mm 0.62 inch 5/8 2.9 Inner Diameter 20 mm 0.78 inch 3/4" 2.10 Inner Diameter 25 mm 0.98 inch 1 2.11 HL-Series 2.12 M-Series 2.13 PPA-Series 2.14 HT-Series
3 4 5
3 Technical Information 3.1 SPIR STAR High-Pressure Hose Assemblies Instructions on Installing and Operating 3.2 Care and Use of High-Pressure Hose 3.3 Hose Types by Common Application 3.4 Table of Pressure Drop Figures
page 1 of 1
Type 6 / 2 WHT
Hose ID in mm
Series Description
Hose Series DC1 H HT K L M OK PPA R W Double Cover Reinforced version For very high temperatures Very high chemical resistant PVDF inner core, PVDF outer cover Braided layer Extremely flexible For methanol service PA11 inner core, PA outer cover Braided layer outer cover For high temperatures Very high chemical resistant PVDF inner core, PA outer cover Reinforced outer cover 2 wide layers of spiralized wire
Page 1 of 1
Hose Types
Type ID [mm] [in] Hose Size OD [mm] [in] Pressure Rating Working Burst [bar] [psi] [bar] [psi] Bend Radius [mm] Weight [lbs/ft] Insert ID [mm] [in] Sleeve OD [mm] [in]
[in] [kg/m]
ID3
3/2 3/4 3/6 3,4 3,4 3,0 0,13 0,13 0,12 6,9 8,0 9,1 0,27 0,31 0,36 1.000 2.000 2.800 14.500 29.000 40.600 2.500 5.000 7.000 36.250 72.500 101.500 60 110 150 2,36 4,33 5,91 0,072 0,135 0,222
ID4
4/2 4/2K 4/2W 4/4 4/6 4/8 4,0 4,0 4,0 4,0 4,0 4,0 0,16 0,16 0,16 0,16 0,16 0,16 8,0 9,8 9,8 10,3 11,5 12,8 0,31 0,39 0,39 0,41 0,45 0,50 1.200 1.200 1.400 2.200 2.800 3.200 17.400 17.400 20.300 31.900 40.600 46.400 3.000 3.000 3.500 5.500 7.000 8.000 43.500 43.500 50.750 79.750 101.500 116.000 75 65 65 130 175 175 2,95 2,56 2,56 5,12 6,89 6,89 0,110 0,185 0,160 0,234 0,365 0,540
ID5
5/2 5/2OK 5/3 5/4 5/6 5/6H 5/6HDC1 5mmUHP 5,0 5,0 5,0 5,0 4,8 4,6 4,6 4,5 0,20 0,20 0,20 0,20 0,19 0,18 0,18 0,18 9,4 10,8 10,3 11,2 13,2 14,4 18,4 15,3 0,37 0,43 0,41 0,44 0,52 0,57 0,72 0,60 1.040 1.040 1.120 1.800 2.500 2.800 2.800 3.200 15.080 15.080 16.240 26.100 36.250 40.600 40.600 46.400 2.600 2.600 2.800 4.500 6.250 7.000 7.000 8.000 37.700 37.700 40.600 65.250 90.625 101.500 101.500 116.000 95 95 95 150 200 220 220 250 3,74 3,74 3,74 5,91 7,87 8,66 8,66 9,84 0,125 0,220 0,218 0,260 0,450 0,563 0,687 0,693
ID6
6/2 6/2OK 6/2K 6/2W 6/2WL 6/2WL Twin 6/3 6/4 6/6H 6mmUHP 6,3 6,2 6,2 6,0 5,9 5,9 6,1 6,3 5,9 5,8 0,25 0,24 0,24 0,24 0,23 0,23 0,24 0,25 0,23 0,23 11,5 13,1 12,9 12,0 12,0 12,0 12,3 12,6 16,4 18,6 0,45 0,52 0,51 0,47 0,47 0,47 0,48 0,50 0,65 0,73 1.000 1.000 1.120 1.280 1.200 1.200 1.040 1.500 2.800 3.200 14.500 14.500 16.240 18.560 17.400 17.400 15.080 21.750 40.600 46.400 2.500 2.500 2.800 3.200 3.000 3.000 2.600 3.800 7.000 8.000 36.250 36.250 40.600 46.400 43.500 43.500 37.700 55.100 101.500 116.000 110 110 95 95 80 80 110 180 250 280 4,33 4,33 3,74 3,74 3,15 3,15 4,33 7,09 9,84 11,02 0,175 0,306 0,300 0,230 0,237 0,237 0,280 0,295 0,750 1,060
ID8
8/2 8/2PA 8/2W 8/2WL 8/2W Twin 8/2WR 8/4 8/6 8/6H 8/6HDC1 8/6UHP 8/6UHP-X 8mmUHP 8,1 8,1 8,0 8,0 8,0 8,0 8,0 8,0 7,7 7,7 7,6 7,6 7,6 0,32 0,32 0,31 0,31 0,31 0,31 0,31 0,31 0,30 0,30 0,30 0,30 0,30 13,3 13,3 14,3 14,0 14,3 16,0 14,6 16,4 18,8 22,8 19,3 19,3 22,0 0,52 0,52 0,56 0,55 0,56 0,63 0,57 0,65 0,74 0,90 0,76 0,76 0,87 900 840 1.040 1.000 1.040 1.040 1.500 2.100 2.500 2.500 2.800 3.035 3.200 13.050 12.180 15.080 14.500 15.080 15.080 21.750 30.450 36.250 36.250 40.600 44.008 46.400 2.250 2.100 2.600 2.500 2.600 2.600 3.800 5.250 6.250 6.250 7.000 7.000 7.400 32.625 30.450 37.700 36.250 37.700 37.700 55.100 76.125 90.625 90.625 101.500 101.500 107.300 130 130 110 100 110 110 200 250 260 260 300 300 300 5,12 5,12 4,33 3,94 4,33 4,33 7,87 9,84 10,24 10,24 11,81 11,81 11,81 0,200 0,200 0,314 0,317 0,628 0,364 0,390 0,640 0,925 1,085 1,055 1,055 1,500
Page 1 of 3
Hose Types
Type ID [mm] [in] Hose Size OD [mm] [in] Pressure Rating Working Burst [bar] [psi] [bar] [psi] Bend Radius [mm] Weight [lbs/ft] Insert ID [mm] [in] Sleeve OD [mm] [in]
[in] [kg/m]
ID10
10/2 10/2W 10/4 10/6 10,1 10,0 9,9 9,8 0,40 0,39 0,39 0,39 15,5 17,2 18,4 20,4 0,61 0,68 0,72 0,80 690 1.100 1.500 1.920 10.005 15.950 21.750 27.840 1.725 2.760 3.800 4.800 25.012 40.020 55.100 69.600 160 125 200 250 6,30 4,92 7,87 9,84 0,280 0,430 0,690 1,000
ID13
13/2 13/2W 13/2WR 13/4 13/4H 13/6 13/6H 13mmUHP 12,9 12,8 12,8 12,8 12,8 12,8 12,7 12,8 0,51 0,50 0,50 0,50 0,50 0,50 0,50 0,50 19,3 20,8 22,2 21,4 22,0 23,4 24,8 27,7 0,76 0,82 0,87 0,84 0,87 0,92 0,98 1,09 690 1.040 1.040 1.300 1.400 1.800 2.000 2.800 10.005 15.080 15.080 18.850 20.300 26.100 29.000 40.600 1.725 2.600 2.600 3.250 3.500 4.500 5.000 6.000 25.012 37.700 37.700 47.125 50.750 65.250 72.500 87.000 200 150 150 200 200 300 300 350 7,87 5,91 5,91 7,87 7,87 11,81 11,81 13,78 0,435 0,590 0,590 0,800 0,880 1,160 1,200 2,085
ID16
16/4 16/6 16mmUHP 16,0 15,9 15,9 0,63 0,63 0,63 25,5 27,7 31,8 1,00 1,09 1,25 1.040 1.520 2.000 15.080 22.040 29.000 2.600 3.800 5.000 37.700 55.100 72.500 250 320 400 9,84 12,60 15,75 1,002 1,480 2,523
ID20
20/2 20/2W 20/4 20/6 19,0 18,8 18,8 18,8 0,75 0,74 0,74 0,74 26,2 29,5 28,8 32,8 1,03 1,16 1,13 1,29 520 760 1.040 1.400 7.540 11.020 15.080 20.300 1.300 1.900 2.600 3.500 18.850 27.550 37.700 50.750 240 220 250 350 9,45 8,66 9,84 13,78 0,750 1,160 1,350 2,170
ID25
25/2 25/2W 25/4 25/6 24,8 25,0 24,8 24,8 0,98 0,98 0,98 0,98 33,5 35,6 36,3 39,8 1,32 1,40 1,43 1,57 440 640 900 1.400 6.380 9.280 13.050 20.300 1.100 1.600 2.250 3.000 15.950 23.200 32.625 43.500 300 280 300 600 11,81 11,02 11,81 23,62 0,950 1,490 1,715 2,800
HL-Series
Viper Viper Twin Mamba Mamba Twin Cobra 6,1 6,1 5,9 5,9 5,0 0,24 0,24 0,23 0,23 0,20 12,5 12,5 12,0 12,0 11,2 0,49 0,49 0,47 0,47 0,44 700 700 1.200 1.200 1.800 10.150 10.150 17.400 17.400 26.100 1.800 1.800 3.000 3.000 4.500 26.100 26.100 43.500 43.500 65.250 80 80 80 80 150 3,15 3,15 3,15 3,15 5,91
M-Series
6/2WM 6/4M 8/2WM 10/2WM 13/2WM 25/2KM 6,0 6,0 8,0 10,0 12,7 23,6 0,24 0,24 0,31 0,39 0,50 0,93 12,2 13,0 14,3 17,2 20,8 32,6 0,48 0,51 0,56 0,68 0,82 1,28 690 1.035 690 690 690 345 10.000 15.000 10.000 10.000 10.000 5.000 2.760 4.140 2.760 2.760 2.760 1.380
Page 2 of 3
Hose Types
Type ID [mm] [in] Hose Size OD [mm] [in] Pressure Rating Working Burst [bar] [psi] [bar] [psi] Bend Radius [mm] Weight [lbs/ft] Insert ID [mm] [in] Sleeve OD [mm] [in]
[in] [kg/m]
PPA-Series
5/4PPA 6/2WPPA 6/4PPA 8/2WPPA 8/4PPA 10/4PPA 13/2WPPA 13/4HPPA 16/4PPA 20/4PPA 20/6PPA 25/4PPA 5,0 6,3 6,3 8,0 8,0 10,0 12,8 12,8 16,0 18,8 18,8 24,8 0,20 0,25 0,25 0,31 0,31 0,39 0,50 0,50 0,63 0,74 0,74 0,98 11,2 12,2 12,6 14,5 14,7 18,4 20,8 22,0 25,5 28,8 32,8 36,3 0,44 0,48 0,50 0,57 0,58 0,72 0,82 0,87 1,00 1,13 1,29 1,43 1.035 690 1.035 690 1.035 1.035 690 860 690 690 860 520 15.000 10.000 15.000 10.000 15.000 15.000 10.000 12.500 10.000 10.000 12.500 7.500
Heat-resisting up to 80C (176F) - with PVDF inner core and polyamid outer cover
4.140 2.760 4.140 2.760 4.140 4.140 2.760 3.450 2.760 2.760 3.450 2.070 60.000 40.000 60.000 40.000 60.000 60.000 40.000 50.000 40.000 40.000 50.000 30.000 250 150 280 250 300 300 300 300 400 500 600 500 9,84 5,91 11,02 9,84 11,81 11,81 11,81 11,81 15,75 19,69 23,62 19,69 0,256 0,266 0,305 0,360 0,420 0,680 0,670 1,000 1,082 1,350 2,170 1,820 0,172 0,178 0,204 0,241 0,281 0,456 0,449 0,670 0,725 0,907 1,454 1,223 2,5 3,5 3,5 5,5 4,5 5,5 8,5 7,5 10,5 13,0 13,0 18,0 0,10 0,14 0,14 0,22 0,18 0,22 0,33 0,30 0,41 0,51 0,51 0,71 15,0 17,1 16,4 18,3 20,3 23,1 26,5 29,5 32,7 36,9 43,1 42,3 0,59 0,67 0,64 0,72 0,79 0,90 1,04 1,16 1,28 1,45 1,69 1,66
HT-Series
5/4HT 6/2WHT 6/4HT 8/2WHT 8/4HT 10/4HT 13/4HHT 5,0 6,3 6,3 8,0 8,0 9,9 12,8 0,20 0,25 0,25 0,31 0,31 0,39 0,50 11,2 12,2 12,6 14,5 14,6 18,4 22,0 0,44 0,48 0,50 0,57 0,57 0,72 0,87 1.035 690 1.035 690 1.035 1.035 860 15.000 10.000 15.000 10.000 15.000 15.000 12.500 4.830 2.760 4.140 2.760 4.140 4.140 3.450
Heat-resisting up to 150C (300F) - with PVDF inner core and outer cover
70.000 40.000 60.000 40.000 60.000 60.000 50.000 250 150 280 250 300 300 300 9,84 5,91 11,02 9,84 11,81 11,81 11,81 0,280 0,266 0,320 0,400 0,413 0,695 1,000 0,188 0,178 0,214 0,268 0,277 0,466 0,672 2,5 3,5 3,5 4,0 4,5 5,0 7,5 0,10 0,14 0,14 0,16 0,18 0,20 0,30 15,4 17,1 17,5 20,7 20,2 24,9 29,5 0,60 0,67 0,68 0,81 0,79 0,98 1,16
Page 3 of 3
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 2 layers of high-tensile steel wire Polyamide (PA) Green -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
60 mm 2,36 inch
Dimensions (mm)
A 8,9
B 32,5
Sleeve
Sleeve
10320101
Dimensions (mm)
Part no.
A 2 2
B 28 30
C 7 8
D 8,9 8,9
Page 1 of 2
Thread G1/4"
Material Steel
A 2
B 47
C 19
Insert
Dimensions (mm)
Part no.
A 9,2 9,2
B 16,5 16,5
C 8,5 8,5 19 19
Swivel nut
Swivel nut
50540301 50540305
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 12,1
B 44
Sleeve
Sleeve
10340102
Dimensions (mm)
Part no.
Material Steel
Nut -
A 2 2
B 79,5 84
C 14 20 -
Insert
HP fitting
40340202B 40340224B Stainless steel -
Page 1 of 2
Thread 9/16"x18UNF
Material Steel
A 2
B 59
C 19
Insert
Dimensions (mm)
Part no.
B 18 16 18
C 14 9 14 19 17 19
Swivel nut
Swivel nut
50540601 50340111 50540605
Size (mm)
Material
Hose protection
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 15,3
B 33,5
Sleeve
Sleeve
10360102
Dimensions (mm)
Part no.
Material
Nut
A 1,8 1,8
B 68 76
C 14 20 -
Insert
HP fitting
40360204C 40360224C Stainless steel Stainless steel -
Size (mm)
Material
Hose protection
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 1 of 1
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 2 layers of high-tensile steel wire Polyamide (PA) Green -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
75 mm 2,95 inch
Dimensions (mm)
A 10 10
B 30 34
Sleeve
Sleeve
10420102 10420105
Dimensions (mm)
Part no.
B 28 31 28
C 7 10 7
Dimensions (mm)
Part no.
Thread 1/4"x28UNF LH
Nut -
A 2,5
B 69
C 28 -
Insert
HP fitting
40420205A
Page 1 of 3
Part no.
Nut -
B 49 53 57 53 55 54 54 55
C 8 10 14 12 12 10 10 12 7 8 11 9 11 9 9 8
Insert
Male fitting
30420412A 30420542A 30420422A 30420302A 30420322A 30420042A 30420052A 30420002A
Page 2 of 3
Thread 9/16"x18UNF
Material Steel
Nut 50540601
A 2,5
B 48,5
C 19
Insert
Dimensions (mm)
Part no.
Material Steel Steel AISI 316Ti Steel AISI 316Ti Material Rubber
Relief bores 1 radial 1 radial 1 radial 2 axial 1 radial Crimp ring 1003035
B 18 16,5 16,5 23 23
C 14 8,5 8,5 16 16 19 19 19 32 32
Swivel nut
Swivel nut
50540601 50540301 50540305 51321206 51320205 Part no.
Dimensions (mm)
Length
34 130
Bend restrictor
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Hydraulics:
Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire 1 braided layer of steel wire Outer Cover: Polyurethane (PUR) Colour: Black Temperature: -30C to +60C [-22F to 140F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
65 mm 2,56 inch
Dimensions (mm)
A 13,1 13,1
B 34 34
Sleeve
Sleeve
10430101 10430105
Dimensions (mm)
Part no.
Thread 1/4"x28UNF LH
Nut -
A 2,5
B 69
C 28 -
Insert
HP fitting
40420205A
Male fitting
30420412A 30420542A 30420422A 30420302A 30420322A 30420042A 30420052A 30420002A 1/16"x27NPTF 1/8"x27NPTF 1/4"x18NPTF G1/8" G1/4" M7 M8 M10X1 Steel Steel Steel Steel Steel Steel Steel Steel 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 49 53 57 53 55 54 54 55 8 10 14 12 12 10 10 12 7 8 11 9 11 9 9 8
Page 1 of 2
Thread G1/4"
Material Steel
Nut -
A 2,5
B 60
C 18 17
Insert
Dimensions (mm)
Part no.
B 18 16,5 16,5 23 23
C 14 8,5 8,5 16 16 19 19 19 32 32
Swivel nut
Swivel nut
50540601 50540301 50540305 51321206 51320205
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black -30C to +60C [-22F to 140F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
65 mm 2,56 inch
Dimensions (mm)
A 13,1 13,1
B 34 34
Sleeve
Sleeve
10430101 10430105
Dimensions (mm)
Part no.
Thread 1/4"x28UNF LH
Nut -
A 2,5
B 69
C 28 -
Insert
HP fitting
40420205A
Male fitting
30420412A 30420542A 30420422A 30420302A 30420322A 30420042A 30420052A 30420002A 1/16"x27NPTF 1/8"x27NPTF 1/4"x18NPTF G1/8" G1/4" M7 M8 M10X1 Steel Steel Steel Steel Steel Steel Steel Steel 2,5 2,5 2,5 2,5 2,5 2,5 2,5 2,5 49 53 57 53 55 54 54 55 8 10 14 12 12 10 10 12 7 8 11 9 11 9 9 8
Page 1 of 3
Thread G1/4"
Material Steel
Nut -
A 2,5
B 54,5
C 11 22
Insert
Page 2 of 3
Part no.
Relief bores 1 radial 1 radial 1 radial 2 axial 1 radial Crimp ring 1001921
B 18 16,5 16,5 23 23
C 14 8,5 8,5 16 16 19 19 19 32 32
Swivel nut
Swivel nut
50540601 50540301 50540305 51321206 51320205 Part no. 1.901418
Hose protection
Dimensions (mm)
Part no.
Material Rubber
Length
34 130
Bend restrictor
Accessories combinations
Without hose protection
Description Bend restrictor Bend restrictor Crimp ring 1.9518400 Protection hose 1.901418 1.901418 1003035 Securing grips Securing grips -
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 14,7 14,7
B 49 49
Sleeve
Sleeve
10440102 10440105
Dimensions (mm)
Part no.
Material
Nut
B 82 90 104
C 14 20 24 -
Insert
HP fitting
40460204C 40460224C 40460234C Stainless steel Stainless steel -
Page 1 of 3
Part no.
Thread 1/8"x27NPTF
Material Steel
Nut -
A 1,8
B 70,5
C 10 9
Insert
Male fitting
30440402B
Dimensions (mm)
Part no.
B 18 18 16,5 16,5
C 14 14 8,5 8,5 22 22 19 19
Swivel nut
Swivel nut
50560601 50560605 50540301 50540305
Page 2 of 3
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.901621 1.901621 Protection hose 1.912026 1.912026 Securing grips 9056400 Securing grips 9056400 Securing grips 9056400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Bolt tensioning, pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 17,1
B 49
Sleeve
Sleeve
10460102
Dimensions (mm)
Part no.
Material
Nut
B 82 90 104
C 14 20 24 -
Insert
HP fitting
40460204C 40460224C 40460234C Stainless steel Stainless steel -
Page 1 of 2
Part no.
A 9,2 9,2
B 18 18
C 14 14 22 22
Swivel nut
Swivel nut
50560601 50560605
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.901822 1.901822 Protection hose 1.912026 1.912026 Securing grips 9056400 Securing grips 9056400 Securing grips 9056400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Surface preparation (concrete removal, surface cleaning of buildings, paint removal), ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools), hydroforming
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 8 layers of high-tensile steel wire Polyamide (PA) Dark red -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 19,5
B 49
Sleeve
Sleeve
10480102
Dimensions (mm)
Part no.
Material
Nut
B 82 90 104
C 14 20 24 -
Insert
HP fitting
40460204C 40460224C 40460234C Stainless steel Stainless steel -
Page 1 of 3
Thread 9/16"x18UNF
Material
Nut
A 1,8
B 63
C 22
Insert
Dimensions (mm)
Part no.
A 9,2 9,2
B 18 18
C 14 14 22 22
Swivel nut
Swivel nut
50560601 50560605
Size (mm)
Material
Hose protection
Page 2 of 3
Part no.
Material PUR
Length
34 250
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518306B 1.9518306B Protection hose 1.902026 1.902531 1.902228 Protection hose 1.912026 1.912532 1.912026 1.912532 1003035 1003035 Securing grips 9056400 905640L Securing grips 9056400 Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 2 layers of high-tensile steel wire Polyamide (PA) Green -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
95 mm 3,74 inch
Dimensions (mm)
A 12,9
B 40
Sleeve
Sleeve
10520101
Dimensions (mm)
Part no.
Thread 1/8"x27NPTF
Material Steel
A 3,5
B 31
C 10
D 11,4
Dimensions (mm)
Part no.
Nut -
A 3 3 3 3 3 3
B 56 64 60 58 57,5 61,5
C 10 14 10 12 10 12 10 12 9 14 9 12
Insert
Male fitting
30520401A 30520451A 30520301A 30520321A 30520011A 30520041A
Page 1 of 2
Thread G1/8"
Material Steel
Nut -
A 3
B 61
C 13 9
Insert
Dimensions (mm)
Part no.
Material Steel AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti Material Rubber
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial 1 radial Crimp ring 1003035
Swivel nut
Swivel nut
50540601 50540605 50540301 50540305 50540101 51321206 51320205 Part no.
Dimensions (mm)
Length
34 130
Bend restrictor
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 2 layers of high-tensile steel wire Polyamide (PA) in green 1 braided layer of stainless steel wire -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
95 mm 3,74 inch
Dimensions (mm)
A 3,5
B 31
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 1 of 1
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Polyoxymethylene (POM) Pressure Support: 2 layers of high-tensile steel wire, 1 braided layer of galvanized steel wire Outer Cover: Polyamide (PA) Colour: Green Temperature: -30C to +60C [-22F to 140F]
ID OD Working Pressure Burst Pressure Bend Radius Weight Insert ID
95 mm 3,74 inch
Dimensions (mm)
A 12,9
B 40
Sleeve
Sleeve
10530111
Dimensions (mm)
Part no.
Thread 1/8"x27NPTF
Material Steel
A 3,5
B 31
C 10
D 12,2
Dimensions (mm)
Part no.
Nut -
A 3 3 3 3 3 3
B 56 64 60 58 57,5 61,5
C 10 14 10 12 10 12 10 12 9 14 9 12
Insert
Male fitting
30520401A 30520451A 30520301A 30520321A 30520011A 30520041A
Page 1 of 2
A 3 3
B 54 54
C 19 19
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF G1/4" G1/4" M14x1.5 M24x1.5 M24x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel AISI 316Ti Steel AISI 316Ti Steel Steel Steel AISI 316Ti
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial 1 radial
Swivel nut
Swivel nut
50540601 50540605 50540301 50540305 50540101 51360201 51321206 51320205 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Bolt tensioning, pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, chemical injection, control of subsea hydraulic components, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 15 15
B 49 49
Sleeve
Sleeve
10540101 10540105
Blast-Pro sleeve
10540232 Steel 12,4 24 -
Dimensions (mm)
Part no.
Nut -
B 83 83 90 103
C 14 14 20 24 -
Insert
HP fitting
40540211B 40540215B 40540205B 40540225B
Page 1 of 3
Material
Sleeve
A 3 3
B 45 50
C 16 22 10 10
Blast-Pro HP fitting
Stainless steel 10540232 Stainless steel 10540232
Blast-Pro HP female
40540244Y 40540254Y 3/8"x24UNF 1/4"x28UNF LH Stainless steel 10540232 Stainless steel 10540232 3 3 50 44 15 9 10 8
Dimensions (mm)
Part no.
Thread 1/4"x18NPTF
Material Steel
Nut -
A 2,5
B 71
C 14 14
Insert
Male fitting
30540401B
Page 2 of 3
A 2,5 2,5
B 64 64
C 19 19
Insert
Dimensions (mm)
Part no.
Material Steel AISI 316Ti Steel AISI 316Ti Steel Steel Material
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial Crimp ring 1002224 -
Swivel nut
Swivel nut
50540601 50540605 50540301 50540305 50540101 50860201 Part no. 1.901621 1.901822
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.901621 1.901822 Securing grips 9056400 Securing grips 9056400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Bolt tensioning, pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 17,5 17,5
B 59 59
Sleeve
Sleeve
10560106 10560105
Dimensions (mm)
Part no.
Material
Nut
A 2 2 2 2
C 14 20 24 24 -
Insert
HP fitting
40560294D 40560284D 40560264D 40560274D Stainless steel Stainless steel -
Page 1 of 3
Thread 9/16"x18UNF
Material
Nut
A 2
B 72
C 22
Insert
HP female fitting
20560614D 9/16"x18UNF Stainless steel 50560605, 50560601 2 68 22
Dimensions (mm)
Part no.
B 18 18 19 16,5
C 14 14 11 8,5 22 22 22 19
Swivel nut
Swivel nut
50560601 50560605 50560301 50540101 Part no. 1.901822 1.902026 1.902531
Hose protection
Dimensions (mm)
Part no.
Material PUR
Length
34 250 -
Bend restrictor
Page 2 of 3
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518306A 1.9518306A Protection hose 1.901822 1.903039 1.902531 Protection hose 1.912026 1.912532 1.912532 1.912532 1003035 1003035 Securing grips 9056400 905640L Securing grips 9056400 Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Bolt tensioning, pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Red -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 19,4
B 64,5
Sleeve
Sleeve
10560126
Dimensions (mm)
Part no.
Material
Nut
A 2 2 2 2
C 14 20 24 24 -
Insert
HP fitting
40560294D 40560284D 40560264D 40560274D Stainless steel Stainless steel -
Page 1 of 3
Thread M14x1.5
Material
Nut
A 2
B 71
C 19
Insert
HP female fitting
20560614D 9/16"x18UNF Stainless steel 50560605, 50560601 2 68 22
Dimensions (mm)
Part no.
B 18 18 19 16,5
C 14 14 11 8,5 22 22 22 19
Swivel nut
Swivel nut
50560601 50560605 50560301 50540101 Part no. 1.902026 1.902228 1.902531
Hose protection
Page 2 of 3
Part no.
Material PUR
Length
34 250
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518306B 1.9518306B Protection hose 1.902026 1.902531 1.902228 1.902531 Protection hose 1.912235 1.912532 1.912532 1.912532 1003035 1003035 Securing grips 9056400 905640L Securing grips 9056400 905640L Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Bolt tensioning, pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire First: Polyamide (PA), Second: Polyurethane (PUR) First: green, second: red -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 19,4
B 64,5
Sleeve
Sleeve
10560126
Dimensions (mm)
Part no.
Material
Nut
A 2 2 2 2
C 14 20 24 24 -
Insert
HP fitting
40560294D 40560284D 40560264D 40560274D Stainless steel Stainless steel -
Page 1 of 2
Thread 9/16"x18UNF
Material
Nut
A 2
B 72
C 22
Insert
HP female fitting
20560614D 9/16"x18UNF Stainless steel 50560605, 50560601 2 68 22
Dimensions (mm)
Part no.
B 18 18 19 16,5
C 14 14 11 8,5 22 22 22 19
Swivel nut
Swivel nut
50560601 50560605 50560301 50540101
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels), hydroforming
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 8 layers of high-tensile steel wire Polyamide (PA) Chrome yellow -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 19,7
B 69
Sleeve
Sleeve
10580116
Dimensions (mm)
Part no.
Material
Nut
C 14 20 24 24 -
Insert
HD fitting
40560294E 40560284E 40560264E 40560274E Stainless steel Stainless steel -
Page 1 of 3
Thread
Material
Nut
A 2,5
B 77
C 22
Insert
HP female swivel
20560614E 9/16"x18UNF Stainless steel 50560605, 50560601 2,5 73 22
Dimensions (mm)
Part no.
B 18 18 19 16,5
C 14 14 11 8,5 22 22 22 19
Swivel nut
Swivel nut
50560601 50560605 50560301 50540101 Part no.
Dimensions (mm)
Length
34 250
Bend restrictor
Size (mm)
Material
Hose protection
Page 2 of 3
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518306C 1.9518306C Protection hose 1.902228 1.902531 1.902228 Protection hose 1.912235 1.912532 1.912235 1.912532 1003035 1003035 Securing grips 9086400 908640L Securing grips 9086400 Securing grips 9086400 908640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 2 layers of high-tensile steel wire Polyamide (PA) Green -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 13,9
B 42
Sleeve
Sleeve
10620101
Dimensions (mm)
Part no.
A 4 4
B 35 35
C 14 14
D 13,5 13,5
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 4
B 95
C 24 -
Insert
HP fitting
40620205A 9/16"x18UNF LH AISI 316Ti
Male fitting
30620411A 30620401A 1/8"x27NPTF 1/4"x18NPTF Steel Steel 4 4 58 68 10 14 12 14
Page 1 of 4
Part no.
Nut -
A 4 4
B 68 64
C 14 14 14 17
Insert
Male fitting
30620405A 30620451A
Page 2 of 4
A 4 4 4
B 65 75 73
C 22 30 32
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 9/16"x18UNF G1/4" G1/4" M14x1.5 M16x1.5 M16x1.5 M18x1.5 M22x1.5 M22x1.5 M24x1.5
Material Steel AISI 316Ti AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti Steel Steel AISI 316Ti Steel
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial 2 axial 2 axial
A 9,2 9,2 9,5 9,2 9,2 9,2 9,2 9,5 9,2 14,2 14,2 16,8
Swivel nut
Swivel nut
50540601 50540605 S5063615 50540301 50540305 50540101 50620121 50620125 50620201 51060201 51060205 51321206
Page 3 of 4
Size (mm)
Material
Hose protection
Dimensions (mm)
Part no.
Material Rubber
Length
34 126
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518600 1.9518600 Protection hose 1.901418 1.901418 1.901822 1.901822 1003035 1003035 Securing grips 9056400 905640L Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 4 of 4
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 2 layers of high-tensile steel wire Polyoxymethylene (POM) in green 1 braided layer of stainless steel wire -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 4
B 35
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 1 of 1
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, control of subsea hydraulic components
Technical Information Inner Core: Polyamide (PA) Pressure Support: 2 layers of high-tensile steel wire 1 braided layer of steel wire Outer Cover: Polyurethane (PUR) Colour: Black Temperature: -30C to +60C [-22F to 140F]
ID OD Working Pressure Burst Pressure Bend Radius Weight Insert ID
95 mm 3,74 inch
Dimensions (mm)
A 14,1
B 42
Sleeve
Sleeve
10630101
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 4
B 95
C 24 -
Insert
HP fitting
40620205A 9/16"x18UNF LH AISI 316Ti
Male fitting
30620411A 30620401A 30620405A 30620451A 1/8"x27NPTF 1/4"x18NPTF 1/4"x18NPTF 3/8"x18NPTF Steel Steel AISI 316Ti Steel 4 4 4 4 58 68 68 64 10 14 14 14 12 14 14 17
Page 1 of 3
Thread G1/4"
Material Steel
Nut -
A 4
B 67
C 18 17
Insert
Page 2 of 3
Part no.
Thread 9/16"x18UNF
Nut S5063615
A 4
B 53
C 19
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 9/16"x18UNF G1/4" G1/4" M14x1.5 M16x1.5 M16x1.5 M18x1.5 M22x1.5 M22x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel AISI 316Ti AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti Steel Steel AISI 316Ti Steel
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial 2 axial 2 axial
A 9,2 9,2 9,5 9,2 9,2 9,2 9,2 9,5 9,2 14,2 14,2 16,8
Swivel nut
Swivel nut
50540601 50540605 S5063615 50540301 50540305 50540101 50620121 50620125 50620201 51060201 51060205 51321206 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, control of subsea hydraulic components
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
95 mm 3,74 inch
Dimensions (mm)
A 15,4 15,4
B 43 43
Sleeve
Sleeve
10630191W 10630195W
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 4
B 95
C 24 -
Insert
HP fitting
40620205A 9/16"x18UNF LH AISI 316Ti
Male fitting
30620411A 30620401A 30620405A 30620451A 1/8"x27NPTF 1/4"x18NPTF 1/4"x18NPTF 3/8"x18NPTF Steel Steel AISI 316Ti Steel 4 4 4 4 58 68 68 64 10 14 14 14 12 14 14 17
Page 1 of 3
Thread G1/4"
Material Steel
Nut -
A 4
B 67
C 18 17
Insert
Page 2 of 3
Part no.
Thread 9/16"x18UNF
Nut S5063615
A 4
B 53
C 19
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 9/16"x18UNF G1/4" G1/4" M14x1.5 M16x1.5 M16x1.5 M18x1.5 M22x1.5 M22x1.5 M24x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel AISI 316Ti AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti Steel Steel AISI 316Ti Steel Steel
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial 2 axial 1 radial 2 axial
A 9,2 9,2 9,5 9,2 9,2 9,2 9,2 9,5 9,2 14,2 14,2 16,8 16,8
Swivel nut
Swivel nut
50540601 50540605 S5063615 50540301 50540305 50540101 50620121 50620125 50620201 51060201 51060205 51360201 51321206 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Hydraulics: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Torque wrenching
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black and red -30C to +60C [-22F to 140F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
95 mm 3,74 inch
Dimensions (mm)
A 14,1
B 42
Sleeve
Sleeve
10630101
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 4
B 95
C 24 -
Insert
HP fitting
40620205A 9/16"x18UNF LH AISI 316Ti
Male fitting
30620411A 30620401A 30620405A 30620451A 1/8"x27NPTF 1/4"x18NPTF 1/4"x18NPTF 3/8"x18NPTF Steel Steel AISI 316Ti Steel 4 4 4 4 58 68 68 64 10 14 14 14 12 14 14 17
Page 1 of 3
Nut -
A 4 4
B 61 61
C 11 11 22 24
Insert
Page 2 of 3
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 9/16"x18UNF G1/4" G1/4" M14x1.5 M16x1.5 M16x1.5 M18x1.5 M22x1.5 M22x1.5 M24x1.5 M24x1.5
Material Steel AISI 316Ti AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti Steel Steel AISI 316Ti Steel Steel
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial 2 axial 1 radial 2 axial
A 9,2 9,2 9,5 9,2 9,2 9,2 9,2 9,5 9,2 14,2 14,2 16,8 16,8
Swivel nut
Swivel nut
50540601 50540605 S5063615 50540301 50540305 50540101 50620121 50620125 50620201 51060201 51060205 51360201 51321206
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Hydraulics:
Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, control of subsea hydraulic components
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
80 mm 3,15 inch
Dimensions (mm)
A 15,4 15,4
B 43 43
Sleeve
Sleeve
10630191W 10630195W
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 4
B 95
C 24 -
Insert
HP fitting
40620205A 9/16"x18UNF LH AISI 316Ti
Male fitting
30620411A 30620401A 30620405A 30620451A 1/8"x27NPTF 1/4"x18NPTF 1/4"x18NPTF 3/8"x18NPTF Steel Steel AISI 316Ti Steel 4 4 4 4 58 68 68 64 10 14 14 14 12 14 14 17
Page 1 of 4
Thread G1/4"
Material Steel
Nut -
A 4
B 67
C 18 17
Insert
Page 2 of 4
Part no.
Thread 9/16"x18UNF
Nut S5063615
A 4
B 53
C 19
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 9/16"x18UNF G1/4" G1/4" M14x1.5 M16x1.5 M16x1.5 M18x1.5 M22x1.5 M22x1.5 M24x1.5
Material Steel AISI 316Ti AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti Steel Steel AISI 316Ti Steel
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial 2 axial 2 axial
A 9,2 9,2 9,5 9,2 9,2 9,2 9,2 9,5 9,2 14,2 14,2 16,8
Swivel nut
Swivel nut
50540601 50540605 S5063615 50540301 50540305 50540101 50620121 50620125 50620201 51060201 51060205 51321206
Page 3 of 4
Part no.
Material Rubber
Length
34 126
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518600 1.9518600 1003035 1003035 Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 4 of 4
Applications Hydraulics: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Torque wrenching
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black and blue -30C to +60C [-22F to 140F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
80 mm 3,15 inch
Dimensions (mm)
A 15,4 15,4
B 43 43
Sleeve
Sleeve
10630191W 10630195W
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 4
B 95
C 24 -
Insert
HP fitting
40620205A 9/16"x18UNF LH AISI 316Ti
Male fitting
30620411A 30620401A 30620405A 30620451A 1/8"x27NPTF 1/4"x18NPTF 1/4"x18NPTF 3/8"x18NPTF Steel Steel AISI 316Ti Steel 4 4 4 4 58 68 68 64 10 14 14 14 12 14 14 17
Page 1 of 3
Nut -
A 4 4
B 61 61
C 11 11 22 24
Insert
Page 2 of 3
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 9/16"x18UNF G1/4" G1/4" M14x1.5 M16x1.5 M16x1.5 M18x1.5 M22x1.5 M22x1.5 M24x1.5
Material Steel AISI 316Ti AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti Steel Steel AISI 316Ti Steel
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial 2 axial 2 axial
A 9,2 9,2 9,5 9,2 9,2 9,2 9,2 9,5 9,2 14,2 14,2 16,8
Swivel nut
Swivel nut
50540601 50540605 S5063615 50540301 50540305 50540101 50620121 50620125 50620201 51060201 51060205 51321206
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Polyoxymethylene (POM) Pressure Support: 2 layers of high-tensile steel wire, 1 braided layer of galvanized steel wire Outer Cover: Polyamide (PA) Colour: Green Temperature: -30C to +60C [-22F to 140F]
ID OD Working Pressure Burst Pressure Bend Radius Weight Insert ID
A 14,1
B 42
Sleeve
Sleeve
10630111
Dimensions (mm)
Part no.
Thread 1/4"x18NPTF
Material Steel
A 4
B 35
C 14
D 14
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 4
B 95
C 24 -
Insert
HP fitting
40620205A 9/16"x18UNF LH AISI 316Ti
Male fitting
30620411A 30620401A 30620405A 30620451A 1/8"x27NPTF 1/4"x18NPTF 1/4"x18NPTF 3/8"x18NPTF Steel Steel AISI 316Ti Steel 4 4 4 4 58 68 68 64 10 14 14 14 12 14 14 17
Page 1 of 3
Nut -
A 4 4 4
B 59 62,5 60,5
C 10 12 12 9 14 17
Insert
Page 2 of 3
A 4 4 4
B 65 75 73
C 22 30 32
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 9/16"x18UNF G1/4" G1/4" M14x1.5 M16x1.5 M16x1.5 M18x1.5 M22x1.5 M22x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel AISI 316Ti AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti Steel Steel AISI 316Ti Steel
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial 2 axial 2 axial
A 9,2 9,2 9,5 9,2 9,2 9,2 9,2 9,5 9,2 14,2 14,2 16,8
Swivel nut
Swivel nut
50540601 50540605 S5063615 50540301 50540305 50540101 50620121 50620125 50620201 51060201 51060205 51321206 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Bolt tensioning, pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, chemical injection, control of subsea hydraulic components, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 16,4 16,4
B 49 49
Sleeve
Sleeve
10640101 10640105
Blast-Pro sleeve
10640232 Steel 14,5 26 -
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Nut -
A 3,5
B 90
C 20 -
Insert
HP fitting
40640205B
Page 1 of 4
Thread 3/8"x24UNF LH
Material
Sleeve
A 4
B 52
C 21 12
Blast-Pro HP fitting
Stainless steel 10640232
Blast-Pro HP female
40640234Y 3/8"x24UNF Stainless steel 10640232 4 50 15 12
Dimensions (mm)
Part no.
Thread 1/4"x18NPTF
Material Steel
Nut -
A 3,5
B 70
C 14 14
Insert
Male fitting
30640401B
Page 2 of 4
Part no.
B 18 18 16,5 22
C 14 14 8,5 12 19 19 19 22
Swivel nut
Swivel nut
50540601 50540605 50540301 50620201 Part no. 1.901822 1.902026
Hose protection
Dimensions (mm)
Part no.
Material Rubber
Length
34 126
Bend restrictor
Page 3 of 4
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518600 1.9518600 Protection hose 1.901822 1.901822 1.902026 1.902026 Protection hose 1.912026 1.912026 1.912026 1.912026 1003035 1003035 Securing grips 9056400 905640L Securing grips 9056400 905640L Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 4 of 4
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Red -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 21,4
B 64,5
Sleeve
Sleeve
10660102
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Material
Nut
A 3 3 3
B 98 112 112
C 20 24 24 -
Insert
HP fitting
40660204C 40660224C 40660124C Stainless steel 9/16"x18UNF LH Stainless steel M14x1.5 LH Stainless steel -
Page 1 of 3
Part no.
A 9,2 9,2
B 18 18
C 14 14 22 22
Swivel nut
Swivel nut
50560601 50560605
Size (mm)
Material
Hose protection
Dimensions (mm)
Part no.
Material PUR
Length
44 250
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Page 2 of 3
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9523406A 1.9523406A Protection hose 1.902531 1.903039 1.902531 1.903039 Protection hose 1.912235 1.913240 1.912235 1.913240 1004145 1004145 Securing grips 9086400 908640L Securing grips 9086400 908640L Securing grips 9086400 908640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning Pressure test equipment (valves, tooling and control panels)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 8 layers of high-tensile steel wire Polyamide (PA) Chrome yellow -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 23,7
B 66
Sleeve
Sleeve
10680102
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Material
Nut
A 3 3 3
B 98 112 112
C 20 24 24 -
Insert
HP fitting
40660204C 40660224C 40660124C Stainless steel 9/16"x18UNF LH Stainless steel M14x1.5 LH Stainless steel -
Page 1 of 3
Part no.
A 9,2 9,2
B 18 18
C 14 14 22 22
Swivel nut
Swivel nut
50560601 50560605
Size (mm)
Material
Hose protection
Dimensions (mm)
Part no.
Material PUR
Length
44 250
Bend restrictor
Page 2 of 3
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9523406B 1.9523406B Protection hose 1.902531 1.903039 1.902531 1.903039 Protection hose 1.912532 1.913240 1.912532 1.913240 1004145 1004145 Securing grips 9086400 908640L Securing grips 9086400 908640L Securing grips 9086400 908640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal) Pressure test equipment (valves, tooling and control panels)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 2 layers of high-tensile steel wire Polyamide (PA) Green -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 17,8
B 47
Sleeve
Sleeve
10820101
Dimensions (mm)
Part no.
A 5,5 5,5
B 39 38
C 14 14
D 17,5 17,5
Dimensions (mm)
Part no.
Nut -
A 5,5 5,5
B 68 69
C 14 14 14 17
Insert
Male fitting
30820411A 30820401A
Page 1 of 3
Thread G1/4"
Material Steel
Nut -
A 5,5
B 70
C 15 12
Insert
Page 2 of 3
Part no.
Material Steel AISI 316Ti Steel AISI 316Ti Steel Steel Steel Material Rubber
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial Crimp ring 1003035
Swivel nut
Swivel nut
50820601 50820605 50840601 50840605 50860301 50860201 51321206 Part no.
Dimensions (mm)
Length
34 126
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518600 1.9518600 1003035 1003035 Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Surface preparation (concrete removal, surface cleaning of buildings, paint removal) Pressure test equipment (valves, tooling and control panels)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 layers of high-tensile steel wire Polyamide (PA) Blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 17,8
B 47
Sleeve
Sleeve
10820101
Dimensions (mm)
Part no.
Nut -
A 5,5 5,5
B 68 69
C 14 14 14 17
Insert
Male fitting
30820411A 30820401A
Page 1 of 3
Thread G1/4"
Material Steel
Nut -
A 5,5
B 70
C 15 12
Insert
Dimensions (mm)
Part no.
A 5,5 5,5
B 39 38
C 14 14
D 17,5 17,5
Dimensions (mm)
Thread G3/8"
Material Steel
Nut 50860301
A 5,5
B 62
C 24
Insert
Page 2 of 3
Thread 3/4"x16UNF
A 5,5
B 62
C 24
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 3/4"x16UNF 3/4"x16UNF G3/8" M20x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel AISI 316Ti Steel AISI 316Ti Steel Steel Steel
Swivel nut
Swivel nut
50820601 50820605 50840601 50840605 50860301 50860201 51321206 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Surface preparation (concrete removal, surface cleaning of buildings, paint removal) Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, control of subsea hydraulic components, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 18,3 18,3
B 47 43
Sleeve
Sleeve
10830191W 10830195W
Dimensions (mm)
Part no.
Nut -
A 5,5 5,5
B 68 69
C 14 14 14 17
Insert
Male fitting
30820411A 30820401A
Page 1 of 3
Thread G1/4"
Material Steel
Nut -
A 5,5
B 70
C 15 12
Insert
Page 2 of 3
Thread 3/4"x16UNF
A 5,5
B 62
C 24
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 3/4"x16UNF 3/4"x16UNF G3/8" M20x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel AISI 316Ti Steel AISI 316Ti Steel Steel Steel
Swivel nut
Swivel nut
50820601 50820605 50840601 50840605 50860301 50860201 51321206 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Hydraulics: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Torque wrenching
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black and blue -30C to +60C [-22F to 140F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
A 18,3 18,3
B 47 43
Sleeve
Sleeve
10830191W 10830195W
Dimensions (mm)
Part no.
Nut -
A 5,5 5,5
B 68 69
C 14 14 14 17
Insert
Male fitting
30820411A 30820401A
Page 1 of 2
Thread G3/8"
Material Steel
Nut 50860301
A 5,5
B 62
C 24
Insert
Dimensions (mm)
Part no.
Material Steel AISI 316Ti Steel AISI 316Ti Steel Steel Steel
Swivel nut
Swivel nut
50820601 50820605 50840601 50840605 50860301 50860201 51321206
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Oil and Gas: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, nitrogen service
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 18,3 18,3
B 47 43
Sleeve
Sleeve
10830191W 10830195W
Dimensions (mm)
Part no.
Nut -
A 5,5 5,5
B 68 69
C 14 14 14 17
Insert
Male fitting
30820411A 30820401A
Page 1 of 2
Thread G3/8"
Material Steel
Nut 50860301
A 5,5
B 62
C 24
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 3/4"x16UNF 3/4"x16UNF G3/8" M20x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel AISI 316Ti Steel AISI 316Ti Steel Steel Steel
Swivel nut
Swivel nut
50820601 50820605 50840601 50840605 50860301 50860201 51321206 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal) Pressure test equipment (valves, tooling and control panels) Grease injection, nitrogen service
Hydraulics: Oil and Gas: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Silver -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 21,3
B 54,5
Sleeve
Sleeve
10830201WR
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 4,5
B 108,5
C 24 -
Insert
HP fitting
40840205B 9/16"x18UNF LH AISI 316Ti
Male fitting
30840411B 30840401B 30840341B 1/4"x18NPTF 3/8"x18NPTF G1/4" Steel Steel Steel 4,5 4,5 4,5 84 82 82 14 14 14 14 17 14
Page 1 of 3
Thread G3/8"
Material Steel
Nut -
A 4,5
B 84,5
C 12 22
Insert
Dimensions (mm)
Part no.
Material Steel AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti
Relief bores 1 radial 1 radial 1 radial 1 radial 2 axial 2 axial 2 axial 1 radial
Swivel nut
Swivel nut
50840601 50840605 50860301 50840305 51060201 51060205 51321206 51320205
Page 2 of 3
Size (mm)
Material
Hose protection
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.902531 1.902531 Protection hose 1.912532 1.912532 Securing grips 9086400 Securing grips 9086400 Securing grips 9086400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning Pressure test equipment (valves, tooling and control panels) Grease injection, chemical injection, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 20,2 20,2
B 58 58
Sleeve
Sleeve
10840102 10840105
Blast-Pro sleeve
10840142 Steel 17,1 29 -
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 4,5
B 108,5
C 24 -
Insert
HP fitting
40840205B 9/16"x18UNF LH AISI 316Ti
Dimensions (mm)
Thread
Material
Sleeve
A 5
B 75
C 25 15
Blast-Pro MP male
9/16"x18UNF LH Stainless steel 10840142
Page 1 of 4
Part no.
Nut -
B 84 82 82
C 14 14 14 14 17 14
Insert
Male fitting
30840411B 30840401B 30840341B
Dimensions (mm)
Part no.
Swivel nut
Swivel nut
50840601 50840605 50860301 50840305
Page 2 of 4
Part no.
B 23 25 23 23
C 14 14 16 16 30 30 32 32
Swivel nut
Swivel nut
51060201 51060205 51321206 51320205 Part no. 1.902228
Hose protection
Dimensions (mm)
Part no.
Material Rubber
Length
39 130
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Page 3 of 4
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518100 1.9518100 Protection hose 1.902228 1.902228 1.902228 1.902228 Protection hose 1.912235 1.912235 1.912235 1.912235 1003640 1003640 Securing grips 9056400 905640L Securing grips 9056400 905640L Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 4 of 4
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 21,6
B 64
Sleeve
Sleeve
10860106
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Material
Nut
C 20 31 24 -
Insert
HP fitting
40860214C 40860204C 40860104C Stainless steel 9/16"x18UNF LH Stainless steel M14x1.5 LH Stainless steel -
MP fitting
40860324C 3/4"x16UNF LH Stainless steel 4,5 102 18 -
Page 1 of 3
Material
Nut
A 4,5 4,5
B 76 77
C 24 30
Insert
Dimensions (mm)
Part no.
Material Steel AISI 316Ti AISI 316Ti Steel AISI 316Ti Material
Relief bores 1 radial 1 radial 1 radial 2 axial 1 radial Crimp ring 1002830 -
B 22,5 22,5 26 23 23
C 17,5 17,5 20 16 16 24 24 30 32 32
Swivel nut
Swivel nut
50840601 50840605 50860675 51321206 51320205 Part no. 1.902228 1.902531 1.903039
Hose protection
Page 2 of 3
Part no.
Material PUR
Length
44 250
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9523406A 1.9523406A Protection hose 1.902228 1.903039 1.902531 Protection hose 1.912235 1.913240 1.912532 1.913240 1004145 1004145 Securing grips 9086400 908640L Securing grips 9086400 Securing grips 9086400 908640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Red -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 25,3
B 67
Sleeve
Sleeve
10860126
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Material
Nut
C 20 31 24 -
Insert
HP fitting
40860214C 40860204C 40860104C Stainless steel 9/16"x18UNF LH Stainless steel M14x1.5 LH Stainless steel -
MP fitting
40860324C 3/4"x16UNF LH Stainless steel 4,5 102 18 -
Page 1 of 3
Material
Nut
A 4,5 4,5
B 76 77
C 24 30
Insert
Dimensions (mm)
Part no.
Material Steel AISI 316Ti AISI 316Ti Steel AISI 316Ti Material
Relief bores 1 radial 1 radial 1 radial 2 axial 1 radial Crimp ring 1003941
B 22,5 22,5 26 23 23
C 17,5 17,5 20 16 16 24 24 30 32 32
Swivel nut
Swivel nut
50840601 50840605 50860675 51321206 51320205 Part no. 1.903039
Hose protection
Dimensions (mm)
Part no.
Material PUR
Length
44 250
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Page 2 of 3
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9523406B 1.9523406B Protection hose 1.903039 1.903039 1.903039 1.903039 Protection hose 1.913038 1.913240 1.913038 1.913240 1004145 1004145 Securing grips 9086400 908640L Securing grips 9086400 908640L Securing grips 9086400 908640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire First: Polyamide (PA), Second: Polyurethane (PUR) First: red, second: green -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 25,3
B 67
Sleeve
Sleeve
10860126
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Material
Nut
C 20 31 24 -
Insert
HP fitting
40860214C 40860204C 40860104C Stainless steel 9/16"x18UNF LH Stainless steel M14x1.5 LH Stainless steel -
MP fitting
40860324C 3/4"x16UNF LH Stainless steel 4,5 102 18 -
Page 1 of 2
Material
Nut
A 4,5 4,5
B 76 77
C 24 30
Insert
Dimensions (mm)
Part no.
Thread 3/4"x16UNF 3/4"x16UNF 7/8"x14UNF M24x1.5 M24x1.5 Mesh length (mm) 600,00
B 22,5 22,5 26 23 23
C 17,5 17,5 20 16 16 24 24 30 32 32
Swivel nut
Swivel nut
50840601 50840605 50860675 51321206 51320205 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Chrome yellow -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 23
B 87,8
Sleeve
Sleeve
10860116
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Material
Nut
C 20 31 18 31 -
Insert
HP fitting
40860214E 40860204E 40860324E 40860104E Stainless steel 9/16"x18UNF LH Stainless steel 3/4"x16UNF LH M14x1.5 LH Stainless steel Stainless steel -
Page 1 of 3
Part no.
B 22,5 26 35
C 17,5 20 23 24 30 36
Swivel nut
Swivel nut
50840605 50860675 50860695
Size (mm)
Material
Hose protection
Dimensions (mm)
Part no.
Material PUR
Length
44 250
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Page 2 of 3
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9523406B 1.9523406B Protection hose 1.902531 1.903039 1.903039 1.903039 Protection hose 1.912532 1.913240 1.913038 1.913240 1004145 1004145 Securing grips 9086400 908640L Securing grips 9086400 908640L Securing grips 9086400 908640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Chrome yellow -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 23
B 87,8
Sleeve
Sleeve
10860116
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Material
Nut
C 20 31 18 31 -
Insert
HP fitting
40860214E 40860204E 40860324E 40860104E Stainless steel 9/16"x18UNF LH Stainless steel 3/4"x16UNF LH M14x1.5 LH Stainless steel Stainless steel -
Page 1 of 3
Part no.
B 22,5 26 35
C 17,5 20 23 24 30 36
Swivel nut
Swivel nut
50840605 50860675 50860695
Size (mm)
Material
Hose protection
Dimensions (mm)
Part no.
Material PUR
Length
44 250
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Page 2 of 3
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9523406B 1.9523406B Protection hose 1.902531 1.903039 1.902531 1.903039 Protection hose 1.912532 1.913240 1.913038 1.913240 1004145 1004145 Securing grips 9086400 908640L Securing grips 9086400 908640L Securing grips 9086400 908640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 8 layers of high-tensile steel wire Polyamide (PA) Chrome yellow -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 29,7
B 66
Sleeve
Sleeve
10880142
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Material
Nut
C 20 31 24 -
Insert
HP fitting
40860214C 40860204C 40860104C Stainless steel 9/16"x18UNF LH Stainless steel M14x1.5 LH Stainless steel -
MP fitting
40860324C 3/4"x16UNF LH Stainless steel 4,5 102 18 -
Page 1 of 3
Material
Nut
A 4,5 4,5
B 76 77
C 24 30
Insert
Dimensions (mm)
Part no.
Material Steel AISI 316Ti AISI 316Ti Steel AISI 316Ti Material
Relief bores 1 radial 1 radial 1 radial 2 axial 1 radial Crimp ring 1003941 -
B 22,5 22,5 26 23 23
C 17,5 17,5 20 16 16 24 24 30 32 32
Swivel nut
Swivel nut
50840601 50840605 50860675 51321206 51320205 Part no. 1.903039 1.903542
Hose protection
Dimensions (mm)
Part no.
Material PUR
Length
44 250
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Page 2 of 3
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9523406D 1.9523406D Protection hose 1.903039 1.903039 1.903542 1.903542 Protection hose 1.913038 1.913240 1.913240 1.913240 1004145 1004145 Securing grips 9106400 910640L Securing grips 9106400 910640L Securing grips 9106400 910640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Heat exchanger tube cleaning Pressure test equipment (valves, tooling and control panels)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 layers of high-tensile steel wire Polyamide (PA) Green -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 20,8
B 58
Sleeve
Sleeve
11020101
Dimensions (mm)
Part no.
Nut -
B 82 82 86
C 14 14 18 19 19 22
Insert
Male fitting
31020401A 31020405A 31020425A
Page 1 of 2
A 6,5 6,5
B 73 73
C 27 27
Insert
Dimensions (mm)
Part no.
Thread 3/4"x16UNF G1/2" G1/2" M22x1.5 M22x1.5 M24x1.5 Mesh length (mm) 600,00
Material AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti Steel
Swivel nut
Swivel nut
51320615 51060311 51060315 51060201 51060205 51321206 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Control of subsea hydraulic components, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 21,5 21,5
B 58 54
Sleeve
Sleeve
11030191W 11030195W
Dimensions (mm)
Part no.
Nut -
B 82 82 86
C 14 14 18 19 19 22
Insert
Male fitting
31020401A 31020405A 31020425A
Page 1 of 2
A 6,5 6,5
B 73 73
C 27 27
Insert
Dimensions (mm)
Part no.
Thread 3/4"x16UNF G1/2" G1/2" M22x1.5 M22x1.5 M24x1.5 Mesh length (mm) 600,00
Material AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti Steel
Swivel nut
Swivel nut
51320615 51060311 51060315 51060201 51060205 51321206 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, chemical injection, control of subsea hydraulic components, nitrogen service, Gaseous media handling
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 23 23
B 64 64
Sleeve
Sleeve
11040102 11040105
Blast-Pro sleeve
11040232 Steel 21 33 -
Dimensions (mm)
Part no.
Thread
Material
Nut
A 5,5
B 114
C 24 -
Insert
HP fitting
41060204C 9/16"x18UNF LH Stainless steel -
Page 1 of 3
Thread
Material
Sleeve
A 6
B 81
C 25 17
Blast-Pro MP male
9/16"x18UNF LH Stainless steel 11040232
Dimensions (mm)
Thread G3/8"
Material Steel
Nut -
A 5,5
B 80
C 12 17
Insert
Dimensions (mm)
Part no.
Material AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti
Swivel nut
Swivel nut
51320615 51060311 51060315 51060201 51060205 51321206 51320205
Page 2 of 3
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.902531 1.902531 Protection hose 1.912532 1.912532 Securing grips 9086400 Securing grips 9086400 Securing grips 9086400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels)
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 26,6
B 64
Sleeve
Sleeve
11060102
Dimensions (mm)
Part no.
Thread
Material
Nut
A 5,5
B 114
C 24 -
Insert
HP fitting
41060204C 9/16"x18UNF LH Stainless steel -
Page 1 of 2
Part no.
Relief bores 1 radial 2 axial 2 axial 2 axial 1 radial Crimp ring 1003941
B 23,5 23 25 23 23
C 13,5 14 14 16 16 27 30 30 32 32
Swivel nut
Swivel nut
51060311 51060201 51060205 51321206 51320205 Part no. 1.903039
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.903039 Protection hose 1.913038 1.913038 Securing grips 9086400 Securing grips Securing grips 9086400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal) Pressure test equipment (valves, tooling and control panels) Grease injection
Hydraulics: Oil and Gas: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 layers of high-tensile steel wire Polyamide (PA) Green -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 26
B 58
Sleeve
Sleeve
11320101
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 8,5
B 109
C 12,7 -
Insert
MP fitting
41320205A 9/16"x18UNF LH AISI 316Ti
Male fitting
31320401A 31320405A 1/2"x14NPTF 1/2"x14NPTF Steel AISI 316Ti 8,5 8,5 90 90 18 18 22 22
Page 1 of 3
A 8,5 8,5
B 73 73
C 27 27
Insert
Dimensions (mm)
Part no.
Material Steel
B 28 28 28 23,5 23,5 25 23 23
C 22 22 22 13,5 13,5 14 16 16 32 32 32 27 27 30 32 32
Swivel nut
Swivel nut
51360641 51360643 51360645 51060311 51060315 51360221 51321206 51320205 Stainless steel 1 radial AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti 1 radial 1 radial 1 radial 1 radial 2 axial 1 radial
Page 2 of 3
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.903039 1.903039 Protection hose 1.913038 1.913038 Securing grips 9086400 Securing grips 9086400 Securing grips 9086400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Hydraulics:
Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, control of subsea hydraulic components, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 27,2 27,2
B 58 58
Sleeve
Sleeve
11330191W 11330195W
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 8,5
B 109
C 12,7 -
Insert
MP fitting
41320205A 9/16"x18UNF LH AISI 316Ti
Male fitting
31320401A 31320405A 1/2"x14NPTF 1/2"x14NPTF Steel AISI 316Ti 8,5 8,5 90 90 18 18 22 22
Page 1 of 3
B 85 80 80
C 30 32 36
Insert
Dimensions (mm)
Part no.
Material Steel
B 28 28 28 23,5 23,5 25 23 23
C 22 22 22 13,5 13,5 14 16 16 32 32 32 27 27 30 32 32
Swivel nut
Swivel nut
51360641 51360643 51360645 51060311 51060315 51360221 51321206 51320205 Stainless steel 1 radial AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti 1 radial 1 radial 1 radial 1 radial 2 axial 1 radial
Page 2 of 3
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.903039 1.903542 Protection hose 1.913038 1.913240 Securing grips 9106400 Securing grips 9106400 Securing grips 9106400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal) Pressure test equipment (valves, tooling and control panels) Grease injection, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Silver -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 27,5 27,5
B 64 60
Sleeve
Sleeve
11330206WR 11330205WR
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 7,5
B 118
C 13 -
Insert
MP fitting
41360205O 9/16"x18UNF LH AISI 316Ti
Male fitting
31360401O 31360405O 1/2"x14NPTF 1/2"x14NPTF Steel AISI 316Ti 7,5 7,5 99 99 18 18 22 22
Page 1 of 3
B 97 89 89
C 30 32 36
Insert
Dimensions (mm)
Part no.
Material Steel AISI 316Ti Steel AISI 316Ti Steel Steel Steel AISI 316Ti
Relief bores 1 radial 1 radial 1 radial 1 radial 1 radial 1 radial 2 axial 1 radial
B 28 28 23,5 23,5 25 23 23 23
C 22 22 13,5 13,5 14 16 16 16 32 32 27 27 30 32 32 32
Swivel nut
Swivel nut
51360641 51360645 51060311 51060315 51360221 51360201 51321206 51320205
Page 2 of 3
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.903039 1.903039 Protection hose 1.913038 1.913038 Securing grips 9106400 Securing grips 9106400 Securing grips 9106400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, chemical injection, control of subsea hydraulic components, nitrogen service, Gaseous media handling
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 27,4 27,4
B 64 64
Sleeve
Sleeve
11340122 11340125
Dimensions (mm)
Part no.
Thread
Material
Nut
A 7,5
B 118
C 24 -
Insert
HP fitting
41360214C 9/16"x18UNF LH Stainless steel -
MP fitting
41360204C 3/4"x16UNF LH Stainless steel 7,5 121 25 -
Page 1 of 3
Thread G1/2"
Material
Nut
A 7,5
B 81
C 27
Insert
Dimensions (mm)
Part no.
Material Steel
B 28 28 28 23,5 23,5 23 23
C 22 22 22 13,5 13,5 16 16 32 32 32 27 27 32 32
Swivel nut
Swivel nut
51360641 51360643 51360645 51060315 51060311 51321206 51320205 Stainless steel 1 radial AISI 316Ti AISI 316Ti Steel Steel AISI 316Ti 1 radial 1 radial 1 radial 2 axial 1 radial
Page 2 of 3
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.903039 1.903542 Protection hose 1.913038 1.913240 Securing grips 9106400 Securing grips 9106400 Securing grips 9106400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, chemical injection, control of subsea hydraulic components, nitrogen service, Gaseous media handling
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 29,5
B 63
Sleeve
Sleeve
11340232
Dimensions (mm)
Part no.
Thread
Material
Nut
A 7,5
B 118
C 24 -
Insert
HP fitting
41360214C 9/16"x18UNF LH Stainless steel -
MP fitting
41360204C 3/4"x16UNF LH Stainless steel 7,5 121 25 -
Page 1 of 3
Thread G1/2"
Material
Nut
A 7,5
B 81
C 27
Insert
Dimensions (mm)
Part no.
Material Steel
B 28 28 28 23,5 23,5 23 23
C 22 22 22 13,5 13,5 16 16 32 32 32 27 27 32 32
Swivel nut
Swivel nut
51360641 51360643 51360645 51060311 51060315 51321206 51320205 Stainless steel 1 radial AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti 1 radial 1 radial 1 radial 2 axial 1 radial
Page 2 of 3
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.903039 1.903039 Protection hose 1.913038 1.913038 Securing grips 9106400 Securing grips 9106400 Securing grips 9106400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, nitrogen service
Hydraulics:
Oil and Gas: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 6 layers of high-tensile steel wire Polyamide (PA) Blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 30,2 30,2
B 64 64
Sleeve
Sleeve
11360132 11360135
Dimensions (mm)
Part no.
Thread
Material
Nut
A 7,5
B 118
C 24 -
Insert
HP fitting
41360214C 9/16"x18UNF LH Stainless steel -
MP fitting
41360204C 3/4"x16UNF LH Stainless steel 7,5 121 25 -
Page 1 of 2
Thread 1"x12UNF
Material
Nut
A 7,5
B 84
C 32
Insert
Dimensions (mm)
Part no.
Material Steel
B 28 28 28 23 23
C 22 22 22 16 16 32 32 32 32 32
Swivel nut
Swivel nut
51360641 51360643 51360645 51321206 51320205 Part no. 1.913240 1.914051 Stainless steel 1 radial AISI 316Ti Steel AISI 316Ti Material 1 radial 2 axial 1 radial Crimp ring 1004348 1005054
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.913240 1.914051 Securing grips 9106400 Securing grips 9106400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Hydraulics: Surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, nitrogen service
Oil and Gas: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 6 layers of high-tensile steel wire Polyamide (PA) Red -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 30,2
B 64
Sleeve
Sleeve
11360232
Dimensions (mm)
Part no.
Thread
Material
Nut
A 7,5
B 118
C 24 -
Insert
HP fitting
41360214C 9/16"x18UNF LH Stainless steel -
MP fitting
41360204C 3/4"x16UNF LH Stainless steel 7,5 121 25 -
Page 1 of 2
Thread 1"x12UNF
Material
Nut
A 7,5
B 84
C 32
Insert
Dimensions (mm)
Part no.
Material Steel
B 28 28 28 23 23
C 22 22 22 16 16 32 32 32 32 32
Swivel nut
Swivel nut
51360641 51360643 51360645 51321206 51320205 Part no. 1.914051 Stainless steel 1 radial AISI 316Ti Steel AISI 316Ti Material 1 radial 2 axial 1 radial Crimp ring 1005054
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.914051 1.914051 Securing grips 9106400 Securing grips 9106400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels) Gaseous media handling
Hydraulics: Oil and Gas: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 8 layers of high-tensile steel wire Polyamide (PA) Chrome yellow -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 34,6
B 72
Sleeve
Sleeve
11380242
Dimensions (mm)
Part no.
Thread
Material
Nut
A 7,5
B 118
C 24 -
Insert
HP fitting
41360214C 9/16"x18UNF LH Stainless steel -
MP fitting
41360204C 3/4"x16UNF LH Stainless steel 7,5 121 25 -
Page 1 of 3
Thread M24x1.5
Material
Nut
A 7,5
B 89
C 32
Insert
Dimensions (mm)
Part no.
Material Steel
B 28 28 28 23 23
C 22 22 22 16 16 32 32 32 32 32
Swivel nut
Swivel nut
51360641 51360643 51360645 51321206 51320205 Stainless steel 1 radial AISI 316Ti Steel AISI 316Ti 1 radial 2 axial 1 radial
Page 2 of 3
Size (mm)
Material
Hose protection
Dimensions (mm)
Part no.
Material PUR
Length
54 350
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 24,30 25-30
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor Crimp ring 1.953545 Protection hose 1.914051 1.914553 1.914051 1005054 Securing grips 9136400 Securing grips 9136400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, chemical injection, control of subsea hydraulic components, nitrogen service, Gaseous media handling
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 32,7
B 69
Sleeve
Sleeve
11640112
Dimensions (mm)
Part no.
Thread 3/4"x16UNF LH
Nut -
A 10,5
B 120
C 18 -
Insert
MP fitting
41640305B
Male fitting
31640401B 3/4"x14NPT Steel 10,5 101 18 27
Page 1 of 3
Thread M30x2
Material Steel
Nut 51640201
A 10,5
B 98
C 41
Insert
Dimensions (mm)
Part no.
B 29 31,5 28
C 23 11,5 15 36 46 41
Swivel nut
Swivel nut
51640605 52040645 51640201
Page 2 of 3
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 24,30 25-30
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.914051 1.914051 Securing grips 9136400 Securing grips 9136400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Hydraulics: Surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, chemical injection, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 6 layers of high-tensile steel wire Polyamide (PA) Blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 35
B 68
Sleeve
Sleeve
11660102
Dimensions (mm)
Part no.
Thread M18x1.5 LH
Material
Nut
A 10,5
B 141
C 28 -
Insert
HP fitting
41660114C Stainless steel -
Page 1 of 2
Part no.
Thread 1 5/16"x12UN
Material
Nut
A 10,5
B 94
C 46
Insert
Dimensions (mm)
Part no.
B 34,5 31,5 28
C 14,5 11,5 15 46 46 41
Swivel nut
Swivel nut
52040605 52040645 51640201
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 24,30 25-30
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.914051 1.914051 Securing grips 9136400 Securing grips 9136400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels) Gaseous media handling
Hydraulics: Oil and Gas: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyoxymethylene (POM) 8 layers of high-tensile steel wire Polyamide (PA) Chrome yellow -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 35
B 72
Sleeve
Sleeve
11680242
Dimensions (mm)
Part no.
Thread M18x1.5 LH
Material
Nut
A 10,5
B 141
C 28 -
Insert
HP fitting
41660114C Stainless steel -
Page 1 of 3
Thread 1 5/16"x12UN
Material
Nut
A 10,5
B 100
C 46
Insert
Dimensions (mm)
Part no.
B 34,5 31,5 28
C 14,5 11,5 15 46 46 41
Swivel nut
Swivel nut
52040605 52040645 51640201
Page 2 of 3
Size (mm)
Material
Hose protection
Dimensions (mm)
Part no.
Material PUR
Length
56 350
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 35,10 30-40
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor Crimp ring 1.953845 Protection hose 1.904252 1.904252 1.904252 Protection hose 1.914051 1.915158 1005257 Securing grips 9204400 Securing grips 9204400 Securing grips -
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning Pressure test equipment (valves, tooling and control panels) Grease injection, nitrogen service
Hydraulics: Oil and Gas: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 layers of high-tensile steel wire Polyamide (PA) Green -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 34,2
B 69
Sleeve
Sleeve
12020101
Dimensions (mm)
Part no.
Nut -
A 13 13
B 111 111
C 25 25 36 36
Insert
Male fitting
32020421A 32020425A
Page 1 of 2
Part no.
Thread 1 5/16"x12UN
Nut 52040605
A 13
B 87
C 46
Insert
Dimensions (mm)
Part no.
B 34,5 31,5 30
C 14,5 11,5 18 46 46 46
Swivel nut
Swivel nut
52040605 52040645 52040211
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 24,30 25-30
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, control of subsea hydraulic components, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 36,3
B 64
Sleeve
Sleeve
12020191W
Dimensions (mm)
Part no.
Nut -
A 13 13
B 111 111
C 25 25 36 36
Insert
Male fitting
32020421A 32020425A
Page 1 of 2
Part no.
Thread 1 5/16"x12UN
Nut 52040605
A 13
B 87
C 46
Insert
Dimensions (mm)
Part no.
B 34,5 31,5 30
C 14,5 11,5 18 46 46 46
Swivel nut
Swivel nut
52040605 52040645 52040211
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 35,10 30-40
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Chemical injection, nitrogen service, Gaseous media handling
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 36,9
B 72
Sleeve
Sleeve
12040131
Dimensions (mm)
Part no.
Thread 1"x14UNS LH
Material
Nut
A 13
B 158
C 30 -
Insert
MP fitting
42060304C Stainless steel -
Page 1 of 2
Thread 1 5/16"x12UN
Material
Nut
A 13
B 107
C 46
Insert
Dimensions (mm)
Part no.
A 25,5 25,5
B 31,5 38
C 11,5 22 46 46
Swivel nut
Swivel nut
52040645 52040201
Size (mm)
Material
Hose protection
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 24,30 25-30
Accessories combinations
Without hose protection
Description Securing grip Bend restrictor Crimp ring Protection hose 1.914051 1.914051 Securing grips 9136400 Securing grips 9136400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels) Chemical injection, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 6 layers of high-tensile steel wire Polyamide (PA) Blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 37,2
B 86
Sleeve
Sleeve
12060116
Dimensions (mm)
Part no.
Thread 1"x14UNS LH
Material
Nut
A 13
B 171
C 30 -
Insert
HD fitting
42060304E Stainless steel -
Page 1 of 2
Part no.
A 25,5 25,5
B 31,5 38
C 11,5 22 46 46
Swivel nut
Swivel nut
52040645 52040201
Size (mm)
Material
Hose protection
Dimensions (mm)
Part no.
Material PUR
Length
59 450
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 35,10 30-40
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor Crimp ring 1.954355 Protection hose 1.914553 1.915158 1.915158 1005560 Securing grips 9204400 Securing grips 9204400
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal) Pressure test equipment (valves, tooling and control panels) Nitrogen service
Hydraulics: Oil and Gas: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 layers of high-tensile steel wire Polyamide (PA) Green -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 40
B 75
Sleeve
Sleeve
12520121
Dimensions (mm)
Part no.
Nut -
A 16,5 16,5
B 120 120
C 25 25 36 36
Insert
Male fitting
32530411T 32530415T
Page 1 of 2
Thread M42x2
Material Steel
Nut 52520201
A 16,5
B 110
C 50
Insert
Dimensions (mm)
Part no.
Thread M42x2
Material Steel
A 30,2
B 34
C 22 50
Swivel nut
Swivel nut
52520201
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 35,10 30-40
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Grease injection, control of subsea hydraulic components, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 2 open layers, 2 dense layers of high-tensile steel wire Polyurethane (PUR) Black -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 44
B 74,5
Sleeve
Sleeve
12530111W
Dimensions (mm)
Part no.
Nut -
A 16,5 16,5
B 120 120
C 25 25 36 36
Insert
Male fitting
32530411T 32530415T
Page 1 of 2
Thread M42x2
Material Steel
Nut 52520201
A 16,5
B 110
C 50
Insert
Dimensions (mm)
Part no.
Thread M42x2
Material Steel
A 30,2
B 34
C 22 50
Swivel nut
Swivel nut
52520201
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 35,10 30-40
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Chemical injection, nitrogen service, Gaseous media handling
Hydraulics:
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 4 layers of high-tensile steel wire Polyamide (PA) Grey -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 45,9
B 77
Sleeve
Sleeve
12540235
Dimensions (mm)
Part no.
Nut -
A 19
B 112
C 25 36
Insert
Male fitting
32540405B
Page 1 of 2
Thread 1 5/16"x12UN
Nut 52530645
A 19
B 98
C 41
Insert
Dimensions (mm)
Part no.
B 31,5 34 34
C 11,5 22 35,8 41 50 50
Swivel nut
Swivel nut
52530645 52520201 52521215
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 35,10 30-40
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Waterblast: Heat exchanger tube cleaning, surface preparation (concrete removal, surface cleaning of buildings, paint removal), tank and vessel cleaning, ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel) Pressure test equipment (valves, tooling and control panels) Chemical injection, nitrogen service, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyamide (PA) 6 layers of high-tensile steel wire Polyamide (PA) Blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 49
B 79
Sleeve
Sleeve
12560232
Dimensions (mm)
Part no.
Thread 1"x14UNS LH
Material
Nut
A 17,5
B 165
C 30 -
Insert
MP fitting
42560304C Stainless steel -
Page 1 of 2
Thread M42x2
Material
Nut
A 17,5
B 122
C 50
Insert
Dimensions (mm)
Part no.
Thread M42x2
Material Steel
A 30,2
B 34
C 22 50
Swivel nut
Swivel nut
52520201
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 35,10 30-40
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Torque wrenching
Technical Information Inner Core: Polyamide (PA) Pressure Support: Multi layers of high-tensile steel wire and open synthetic fibers Outer Cover: Polyurethane (PUR) Colour: Luminous yellow Temperature: -30C to +60C [-22F to 140F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
80 mm 3,15 inch
Dimensions (mm)
A 14,1
B 38
Sleeve
Sleeve
VIPER-S
Dimensions (mm)
Part no.
Nut -
A 4 4
B 68 64
C 14 14 14 17
Insert
Male fitting
VIPER-M-1/4 VIPER-M-3/8
Page 1 of 2
Part no.
Material Rubber
Length
34 126
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518400 1.9518400 QR-HL QR-HL Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Torque wrenching
Technical Information Inner Core: Polyamide (PA) Pressure Support: Multi layers of high-tensile steel wire and open synthetic fibers Outer Cover: Polyurethane (PUR) Colour: Luminous yellow and red Temperature: -30C to +60C [-22F to 140F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
80 mm 3,15 inch
Dimensions (mm)
A 14,1
B 38
Sleeve
Sleeve
VIPER-S
Dimensions (mm)
Part no.
Nut -
A 4 4
B 68 64
C 14 14 14 17
Insert
Male fitting
VIPER-M-1/4 VIPER-M-3/8
Dimensions (mm)
Part no.
Material Rubber
Length
34 126
Bend restrictor
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 1 of 1
Applications Hydraulics:
Pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Polyamide (PA) Multi-layers of high-tensile steel wire Polyurethane (PUR) Red -30C to +60C [-22F to 140F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
80 mm 3,15 inch
Dimensions (mm)
A 15,4
B 39
Sleeve
Sleeve
MAMBA-S
Dimensions (mm)
Part no.
Nut -
A 4 4
B 68 64
C 14 14 14 17
Insert
Male fitting
MAMBA-M-1/4 MAMBA-M-3/8
Page 1 of 2
Thread 1/4"x18NPTF
Material Steel
Nut -
A 4
B 67
C 20 19
Insert
Dimensions (mm)
Part no.
Thread G 1/4"
Material Steel
A 9,2
B 16,5
C 8,5 19
Swivel nut
Swivel nut
MAMBA-F-N-1/4
Dimensions (mm)
Part no.
Material Rubber
Length
34 126
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518400 1.9518400 QR-HL QR-HL Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics: Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Torque wrenching
Polyamide (PA) Multi-layers of high-tensile steel wire Polyurethane (PUR) Red and dark grey -30C to +60C [-22F to 140F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
80 mm 3,15 inch
Dimensions (mm)
A 15,4
B 39
Sleeve
Sleeve
MAMBA-S
Dimensions (mm)
Part no.
Nut -
A 4 4
B 68 64
C 14 14 14 17
Insert
Male fitting
MAMBA-M-1/4 MAMBA-M-3/8
Page 1 of 2
Thread 1/4"x18NPTF
Material Steel
Nut -
A 4
B 67
C 20 19
Insert
Dimensions (mm)
Part no.
Thread G 1/4"
Material Steel
A 9,2
B 16,5
C 8,5 19
Swivel nut
Swivel nut
MAMBA-F-N-1/4
Dimensions (mm)
Part no.
Material Rubber
Length
34 126
Bend restrictor
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Bolt tensioning, pressure test equipment (valves, tooling and control panels), hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Polyoxymethylene (POM) multi-layers of high-tensile steel wire Polyamide (PA) Dark blue -30C to +60C [-22F to 140F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
A 15
B 45
Sleeve
Sleeve
COBRA-S
Dimensions (mm)
Thread G 1/4"
Material Steel
Nut -
A 2,5
B 69
C 11 22
Insert
Page 1 of 2
Part no.
Thread G 1/4"
Material Steel
A 9,2
B 16,5
C 8,5 19
Swivel nut
Swivel nut
COBRA-F-N-1/4
Dimensions (mm)
Part no.
Material Rubber
Length
34 126
Bend restrictor
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Accessories combinations
Without hose protection
Description Bend restrictor Securing grip Bend restrictor and securing grip Bend restrictor Crimp ring 1.9518400 1.9518400 QR-HL QR-HL Securing grips 9056400 905640L
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), control of subsea hydraulic components, nitrogen service, jumper/ subsea well control
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
BESNO P40 TLO (PA11) 2 open layers, 2 dense layers of high-tensile steel wire Polyamide (PA) Dark blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
95 mm 3,74 inch
Dimensions (mm)
A 16,8 16,8
B 49 53
Sleeve
Sleeve
10630171W 10630185W
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Nut -
A 4
B 94
C 20 -
Insert
MP fitting
40620305M
Male fitting
30620401M 1/4"x18NPT Steel 4 83 14 14
Page 1 of 2
Part no.
A 4 4
B 64 64
C 19 19
Insert
Dimensions (mm)
Part no.
B 16 16 18 18
C 12 12 14 14 19 19 19 19
Swivel nut
Swivel nut
50620601 50620605 50540601 50540605 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), control of subsea hydraulic components, nitrogen service, jumper/ subsea well control
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
BESNO P40 TLO (PA11) 4 layers of high-tensile steel wire Polyamide (PA) Dark blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 19,9
B 54
Sleeve
Sleeve
10640185W
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Nut -
A 3
B 100
C 20 -
Insert
MP fitting
40640305MB
Page 1 of 2
Part no.
Thread 9/16"x18UNF
Nut 50540605
A 3
B 71
C 19
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF
A 9,2
B 18
C 14 19
Swivel nut
Swivel nut
50540605
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), control of subsea hydraulic components, nitrogen service, jumper/ subsea well control
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
BESNO P40 TLO (PA11) 2 open layers, 2 dense layers of high-tensile steel wire Polyamide (PA) Dark blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 19,7 19,7
B 48 52
Sleeve
Sleeve
10830181W 10830185W
Dimensions (mm)
Part no.
Thread 3/8"x18NPT
Material Steel
Nut -
A 5,5
B 84
C 14 19
Insert
Male fitting
30820401M
Page 1 of 2
Part no.
A 11,2 12,2
B 18 22,5
C 14 17,5 19 24
Swivel nut
Swivel nut
51040615 50840605
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), control of subsea hydraulic components, nitrogen service, jumper/ subsea well control
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
BESNO P40 TLO (PA11) 2 open layers, 2 dense layers of high-tensile steel wire Polyamide (PA) Dark blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 21,5
B 64
Sleeve
Sleeve
11030185W
Dimensions (mm)
Thread 3/4"x16UNF
Nut 51320615
A 5
B 73,5
C 24
Insert
Dimensions (mm)
Part no.
A 11,2 14,2
B 18 22,5
C 14 17,5 19 24
Swivel nut
Swivel nut
51040615 51320615
Page 1 of 2
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), control of subsea hydraulic components, nitrogen service, jumper/ subsea well control
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
BESNO P40 TLO (PA11) 2 open layers, 2 dense layers of high-tensile steel wire Polyamide (PA) Dark blue -30C to +60C [-22F to 140F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 27,8 27,8
B 60 64
Sleeve
Sleeve
11330181W 11330185W
Dimensions (mm)
Part no.
Thread 1/2"x14NPT
Material Steel
Nut -
A 8,5
B 104
C 18 22
Insert
Male fitting
31320401M
Page 1 of 2
Part no.
A 14,2 16,8
B 22,5 28
C 17,5 22 24 32
Swivel nut
Swivel nut
51320615 51360645
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), control of subsea hydraulic components, nitrogen service, jumper/ subsea well control
Technical Information Inner Core: BESNO P40 TLO (PA11) Pressure Support: 2 layers of high-tensile steel wire, 1 braided layer of steel wire Outer Cover: Polyamide (PA) Colour: Dark blue Temperature: -30C to +60C [-22F to 140F]
ID OD Working Pressure Burst Pressure Bend Radius Weight Insert ID
A 42,3
B 74
Sleeve
Sleeve
12530245 AISI 316Ti
Dimensions (mm)
Thread 1 5/16"x12UN
Nut 52530645
A 16,5
B 98
C 41
Insert
Dimensions (mm)
Part no.
A 27,1 27,1
B 31,5 34,5
C 11,5 14,5 41 41
Swivel nut
Swivel nut
52530645 52530605
Page 1 of 2
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 15 15
B 49 49
Sleeve
Sleeve
10540101 10540105
Blast-Pro sleeve
10540232 Steel 12,4 24 -
Dimensions (mm)
Part no.
Nut Sleeve
B 83 83 90 103 B 45 50
C 14 14 20 24 C 16 22 10 10 -
Insert
HP fitting
40540211B 40540215B 40540205B 40540225B Part no. 40540234Y 40540214Y
Dimensions (mm)
Blast-Pro HP fitting
Stainless steel 10540232 Stainless steel 10540232
Page 1 of 3
Material
Sleeve
A 3 3
B 44 50
C 9 15 8 10
Blast-Pro HP female
Stainless steel 10540232 Stainless steel 10540232
Dimensions (mm)
Part no.
Thread 1/4"x18NPTF
Material Steel
Nut -
A 2,5
B 71
C 14 14
Insert
Male fitting
30540401B
Page 2 of 3
Thread M20x1.5
Material Steel
Nut 50860201
A 2,5
B 77
C 27
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF G1/4" G1/4" M14x1.5 M20x1.5 Mesh length (mm) 600,00
Swivel nut
Swivel nut
50540601 50540605 50540301 50540305 50540101 50860201 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 2 open layers, 2 dense layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 17,5
B 64
Sleeve
Sleeve
10640115
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Nut -
A 3,5
B 98
C 20 -
Insert
HP fitting
40640205HB
MP fitting
40640305HB 3/8"x24UNF LH AISI 316Ti 3,5 100 11 -
Page 1 of 2
Thread 9/16"x18UNF
Nut S5063615
A 3,5
B 73
C 19
Insert
Dimensions (mm)
Part no.
A 9,5 9,5
B 18 17,5
C 15 10 19 19
Swivel nut
Swivel nut
S5063615 50620125
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 16,4 16,4
B 49 49
Sleeve
Sleeve
10640101 10640105
Blast-Pro sleeve
10640232 Steel 14,5 26 -
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Nut -
A 3,5
B 90
C 20 -
Insert
HP fitting
40640205B
Dimensions (mm)
Thread 3/8"x24UNF LH
Material
Sleeve
A 4
B 52
C 21 12
Blast-Pro HP fitting
Stainless steel 10640232
Page 1 of 3
Thread 3/8"x24UNF
Material
Sleeve
A 4
B 50
C 15 12
Blast-Pro HP female
Stainless steel 10640232
Dimensions (mm)
Part no.
Thread 1/4"x18NPTF
Material Steel
Nut -
A 3,5
B 70
C 14 14
Insert
Male fitting
30640401B
Page 2 of 3
Thread M18x1.5
Material Steel
Nut 50620201
A 3,5
B 72
C 22
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF G1/4" G1/4" M18x1.5 Mesh length (mm) 600,00
B 18 18 16,5 16,5 22
C 14 14 8,5 8,5 12 19 19 19 19 22
Swivel nut
Swivel nut
50540601 50540605 50540301 50540305 50620201 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 2 open layers, 2 dense layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 18,3 18,3
B 47 43
Sleeve
Sleeve
10830191W 10830195W
Dimensions (mm)
Part no.
Nut -
A 5,5 5,5
B 68 69
C 14 14 14 17
Insert
Male fitting
30820411A 30820401A
Page 1 of 3
Nut -
A 5,5 5,5
B 63 65
C 12 12 14 17
Insert
Page 2 of 3
Thread 3/4"x16UNF
A 5,5
B 62
C 24
Insert
Dimensions (mm)
Part no.
Thread 9/16"x18UNF 9/16"x18UNF 3/4"x16UNF 3/4"x16UNF G3/8" M20x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel AISI 316Ti Steel AISI 316Ti Steel Steel Steel
Swivel nut
Swivel nut
50820601 50820605 50840601 50840605 50860301 50860201 51321206 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 20,2 20,2
B 58 58
Sleeve
Sleeve
10840102 10840105
Blast-Pro sleeve
10840142 Steel 17,1 29 -
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 4,5
B 108,5
C 24 -
Insert
HP fitting
40840205B 9/16"x18UNF LH AISI 316Ti
Page 1 of 3
Thread
Material
Sleeve
A 5
B 75
C 25 15
Blast-Pro MP male
9/16"x18UNF LH Stainless steel 10840142
Dimensions (mm)
Part no.
Nut -
B 84 82 82
C 14 14 14 14 17 14
Insert
Male fitting
30840411B 30840401B 30840341B
Page 2 of 3
A 4,5 4,5
B 73 73
C 24 24
Insert
Dimensions (mm)
Part no.
Thread 3/4"x16UNF 3/4"x16UNF G3/8" G3/8" M22x1.5 M22x1.5 M24x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti
Relief bores 1 radial 1 radial 1 radial 1 radial 2 axial 2 axial 2 axial 1 radial
Swivel nut
Swivel nut
50840601 50840605 50860301 50840305 51060201 51060205 51321206 51320205 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 3 of 3
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 23 23
B 64 64
Sleeve
Sleeve
11040102 11040105
Blast-Pro sleeve
11040232 Steel 21 33 -
Dimensions (mm)
Part no.
Thread
Material
Nut
A 5,5
B 114
C 24 -
Insert
HP fitting
41060204C 9/16"x18UNF LH Stainless steel -
Dimensions (mm)
Thread
Material
Sleeve
A 6
B 81
C 25 17
Blast-Pro MP male
9/16"x18UNF LH Stainless steel 11040232
Page 1 of 2
Thread G3/8"
Material Steel
Nut -
A 5,5
B 80
C 12 17
Insert
Dimensions (mm)
Part no.
Thread 3/4"x16UNF G1/2" G1/2" M22x1.5 M22x1.5 M24x1.5 M24x1.5 Mesh length (mm) 600,00
Material AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti Steel AISI 316Ti
Swivel nut
Swivel nut
51320615 51060311 51060315 51060201 51060205 51321206 51320205 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 2 open layers, 2 dense layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 27,2 27,2
B 58 58
Sleeve
Sleeve
11330191W 11330195W
Dimensions (mm)
Part no.
Thread
Material
Nut -
A 8,5
B 109
C 12,7 -
Insert
MP fitting
41320205A 9/16"x18UNF LH AISI 316Ti
Male fitting
31320401A 31320405A 1/2"x14NPTF 1/2"x14NPTF Steel AISI 316Ti 8,5 8,5 90 90 18 18 22 22
Page 1 of 2
B 85 80 80
C 30 32 36
Insert
Dimensions (mm)
Part no.
Thread 1"x12UNF 1"x12UNF 1"x12UNF G1/2" G1/2" M22x1.5 M24x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel
B 28 28 28 23,5 23,5 25 23 23
C 22 22 22 13,5 13,5 14 16 16 32 32 32 27 27 30 32 32
Swivel nut
Swivel nut
51360641 51360643 51360645 51060311 51060315 51360221 51321206 51320205 Part no. Stainless steel 1 radial AISI 316Ti Steel AISI 316Ti Steel Steel AISI 316Ti 1 radial 1 radial 1 radial 1 radial 2 axial 1 radial
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 29,5
B 63
Sleeve
Sleeve
11340232
Dimensions (mm)
Part no.
Thread
Material
Nut
A 7,5
B 118
C 24 -
Insert
HP fitting
41360214C 9/16"x18UNF LH Stainless steel -
MP fitting
41360204C 3/4"x16UNF LH Stainless steel 7,5 121 25 -
Page 1 of 2
Thread 1"x12UNF
Material
Nut
A 7,5
B 84
C 32
Insert
Dimensions (mm)
Part no.
Thread 1"x12UNF 1"x12UNF 1"x12UNF M24x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel
B 28 28 28 23 23
C 22 22 22 16 16 32 32 32 32 32
Swivel nut
Swivel nut
51360641 51360643 51360645 51321206 51320205 Part no. Stainless steel 1 radial AISI 316Ti Steel AISI 316Ti 1 radial 2 axial 1 radial
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 32,7 32,6
B 69 69
Sleeve
Sleeve
11640112 11640115
Dimensions (mm)
Part no.
Thread 3/4"x16UNF LH
Nut -
A 10,5
B 120
C 18 -
Insert
MP fitting
41640305B
Male fitting
31640401B 3/4"x14NPT Steel 10,5 101 18 27
Page 1 of 2
Thread 1 5/16"x12UN
Nut 52040645
A 10,5
B 99
C 46
Insert
Dimensions (mm)
Part no.
B 29 31,5 28
C 23 11,5 15 36 46 41
Swivel nut
Swivel nut
51640605 52040645 51640201
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 36,9
B 72
Sleeve
Sleeve
12040131
Dimensions (mm)
Part no.
Thread 1"x14UNS LH
Material
Nut
A 13
B 158
C 30 -
Insert
MP fitting
42060304C Stainless steel -
Page 1 of 2
Part no.
A 25,5 25,5
B 31,5 30
C 11,5 18 46 46
Swivel nut
Swivel nut
52040645 52040211
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 24,30 25-30
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 6 layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 42,9
B 72
Sleeve
Sleeve
12060111
Dimensions (mm)
Part no.
Thread 1"x14UNS LH
Material
Nut
A 13
B 158
C 30 -
Insert
MP fitting
42060304C Stainless steel -
Page 1 of 2
Part no.
A 25,5 25,5
B 31,5 38
C 11,5 22 46 46
Swivel nut
Swivel nut
52040645 52040201
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 35,10 30-40
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Applications Hydraulics:
Hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools) Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
ID
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyamide (PA) Dark green -20C to +80C [-4F to 176F]
Working Pressure Burst Pressure Bend Radius Weight Insert ID
OD
A 42,4
B 92
Sleeve
Sleeve
12540125 AISI 316Ti
Dimensions (mm)
Part no.
Nut -
A 18
B 131
C 25 36
Insert
Male fitting
32540405HB
Dimensions (mm)
Part no.
Thread M42x2
A 30,2
B 34
C 35,8 50
Swivel nut
Swivel nut
52521215
Page 1 of 2
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyvinylidenfluoride (PVDF) Light grey -20C to +150C [-4F to 300F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
A 15,4
B 56
Sleeve
Sleeve
10540145
Dimensions (mm)
Part no.
Thread 1/4"x28UNF LH
Nut -
A 2,5
B 86
C 14 -
Insert
HP fitting
40540205H
Page 1 of 2
Thread 9/16"x18UNF
Nut 50540605
A 2,5
B 68
C 19
Insert
Dimensions (mm)
Part no.
A 9,2 9,2
B 18 16,5
C 14 8,5 19 19
Swivel nut
Swivel nut
50540605 50540305
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Important Information! In case of accidental leakage when transferring hot medium through SPIR STAR hoses the potential for injury exists from escaping fluids at high temperature (up to 150 C or 300F) while under pressure. When used for this purpose SPIR STAR HT series hoses should only be used when there is appropriate protecting devices in place to rule out the possibility of injury. The protecting devices may be removed only (e.g. for repairs) after the hose assembly has been depressurized and cooled to ambient temperature.
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Polyvinylidenfluoride (PVDF) 2 open layers, 2 dense layers of high-tensile steel wire Polyvinylidenfluoride (PVDF) Light grey -20C to +150C [-4F to 300F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
A 17,5
B 64
Sleeve
Sleeve
10640115
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Nut -
A 3,5
B 98
C 20 -
Insert
HP fitting
40640205HB
MP fitting
40640305HB 3/8"x24UNF LH AISI 316Ti 3,5 100 11 -
Page 1 of 2
Part no.
Thread 9/16"x18UNF
Nut S5063615
A 3,5
B 69
C 19
Insert
Dimensions (mm)
Part no.
A 9,5 9,5
B 18 17,5
C 15 10 19 19
Swivel nut
Swivel nut
S5063615 50620125
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Important Information! In case of accidental leakage when transferring hot medium through SPIR STAR hoses the potential for injury exists from escaping fluids at high temperature (up to 150 C or 300F) while under pressure. When used for this purpose SPIR STAR HT series hoses should only be used when there is appropriate protecting devices in place to rule out the possibility of injury. The protecting devices may be removed only (e.g. for repairs) after the hose assembly has been depressurized and cooled to ambient temperature.
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyvinylidenfluoride (PVDF) Light grey -20C to +150C [-4F to 300F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
A 17,5
B 64
Sleeve
Sleeve
10640115
Dimensions (mm)
Part no.
Thread 3/8"x24UNF LH
Nut -
A 3,5
B 98
C 20 -
Insert
HP fitting
40640205HB
MP fitting
40640305HB 3/8"x24UNF LH AISI 316Ti 3,5 100 11 -
Page 1 of 2
Part no.
Thread 9/16"x18UNF
Nut S5063615
A 3,5
B 69
C 19
Insert
Dimensions (mm)
Part no.
A 9,5 9,5
B 18 17,5
C 15 10 19 19
Swivel nut
Swivel nut
S5063615 50620125
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Important Information! In case of accidental leakage when transferring hot medium through SPIR STAR hoses the potential for injury exists from escaping fluids at high temperature (up to 150 C or 300F) while under pressure. When used for this purpose SPIR STAR HT series hoses should only be used when there is appropriate protecting devices in place to rule out the possibility of injury. The protecting devices may be removed only (e.g. for repairs) after the hose assembly has been depressurized and cooled to ambient temperature.
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Polyvinylidenfluoride (PVDF) 2 open layers, 2 dense layers of high-tensile steel wire Polyvinylidenfluoride (PVDF) Grey -20C to +150C [-4F to 300F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
A 20,7
B 56
Sleeve
Sleeve
10830145
Dimensions (mm)
Thread 3/4"x16UNF
Nut 50840605
A 4
B 76
C 24
Insert
Page 1 of 2
Part no.
A 10,6 12,2
B 18 22,5
C 14 17,5 19 24
Swivel nut
Swivel nut
50820605 50840605
Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Important Information! In case of accidental leakage when transferring hot medium through SPIR STAR hoses the potential for injury exists from escaping fluids at high temperature (up to 150 C or 300F) while under pressure. When used for this purpose SPIR STAR HT series hoses should only be used when there is appropriate protecting devices in place to rule out the possibility of injury. The protecting devices may be removed only (e.g. for repairs) after the hose assembly has been depressurized and cooled to ambient temperature.
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyvinylidenfluoride (PVDF) Grey -20C to +150C [-4F to 300F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
A 20,2 20,2
B 65 65
Sleeve
Sleeve
10840152 10840155
Dimensions (mm)
Thread G3/8"
Material Steel
A 4,5
B 77
C 24
Insert
Page 1 of 2
Part no.
Material Steel AISI 316Ti Steel AISI 316Ti Overall length (mm) 740,00
Swivel nut
Swivel nut
50840601 50840605 50860301 50840305 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 10,20 10-15
Important Information! In case of accidental leakage when transferring hot medium through SPIR STAR hoses the potential for injury exists from escaping fluids at high temperature (up to 150 C or 300F) while under pressure. When used for this purpose SPIR STAR HT series hoses should only be used when there is appropriate protecting devices in place to rule out the possibility of injury. The protecting devices may be removed only (e.g. for repairs) after the hose assembly has been depressurized and cooled to ambient temperature.
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyvinylidenfluoride (PVDF) Grey -20C to +150C [-4F to 300F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
A 24,9
B 64
Sleeve
Sleeve
11040145
Dimensions (mm)
Thread M22x1.5
A 5
B 92
C 30
Insert
Page 1 of 2
Part no.
B 22,5 18 23 25
C 17,5 14 14 14 24 19 30 30
Swivel nut
Swivel nut
51320615 51040615 51060201 51060205 Part no.
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 15-20
Important Information! In case of accidental leakage when transferring hot medium through SPIR STAR hoses the potential for injury exists from escaping fluids at high temperature (up to 150 C or 300F) while under pressure. When used for this purpose SPIR STAR HT series hoses should only be used when there is appropriate protecting devices in place to rule out the possibility of injury. The protecting devices may be removed only (e.g. for repairs) after the hose assembly has been depressurized and cooled to ambient temperature.
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Methanol service (oil rigs, distribution panels, umbilicals), chemical injection, control of subsea hydraulic components, nitrogen service, jumper/ subsea well control, Gaseous media handling
Technical Information Inner Core: Pressure Support: Outer Cover: Colour: Temperature:
Polyvinylidenfluoride (PVDF) 4 layers of high-tensile steel wire Polyvinylidenfluoride (PVDF) Grey -20C to +150C [-4F to 300F]
ID
OD
Working Pressure
Burst Pressure
Bend Radius
Weight
Insert ID
A 29,5
B 63
Sleeve
Sleeve
11340232
Dimensions (mm)
Part no.
Thread
Material
Nut
A 7,5
B 118
C 24 -
Insert
HP fitting
41360214C 9/16"x18UNF LH Stainless steel -
MP fitting
41360204C 3/4"x16UNF LH Stainless steel 7,5 121 25 -
Page 1 of 2
Part no.
Thread 1"x12UNF 1"x12UNF 1"x12UNF M24x1.5 M24x1.5 Mesh length (mm) 600,00
Material Steel
B 28 28 28 23 23
C 22 22 22 16 16 32 32 32 32 32
Swivel nut
Swivel nut
51360641 51360643 51360645 51321206 51320205 Part no. Stainless steel 1 radial AISI 316Ti Steel AISI 316Ti 1 radial 2 axial 1 radial
Breaking strength Suitable for SPIR STAR hose (kN) outer diameter (mm) 20,40 20-25
Important Information! In case of accidental leakage when transferring hot medium through SPIR STAR hoses the potential for injury exists from escaping fluids at high temperature (up to 150 C or 300F) while under pressure. When used for this purpose SPIR STAR HT series hoses should only be used when there is appropriate protecting devices in place to rule out the possibility of injury. The protecting devices may be removed only (e.g. for repairs) after the hose assembly has been depressurized and cooled to ambient temperature.
Production-related variations of the burst pressure of up to 5 % are possible. The safety factors between the burst pressure and the working pressure as well as the test pressure depend on the operating conditions. For gaseous media the outer cover is to be pinpricked. Regarding the safety factor for gaseous media please contact your local SPIR STAR assembling center. The indicated working pressure refers to the hose only. Depending on the used fitting the permitted working pressure of a hose assembly may be less. BLAST PRO fittings may only be used for tube cleaning operations inside the tube. They have not been designed for the use outside of tubes. We reserve our rights for technical changes without notice. Subject to printing errors.
Page 2 of 2
Safety Information Only trained personnel may execute the installation of our product and set it into operation. Check the high-pressure hose assemblies for kinks, wear and tear, corrosion, cracks and other damages each time before using them. High-pressure hose assemblies showing kinks, cracks, corrosion, leaking fittings or damages of the outer cover reaching down to the reinforcing steel wires have to be exchanged. Use only high-pressure hose assemblies the allowable working pressure of which you know. Do not use leaking high-pressure hose assemblies. Use only clean, filtered media in order to extend the life span of the high-pressure hoses. If a malfunction is suspected, the product or the machine it was mounted to shall be put out of operation immediately and the high-pressure hose assembly exchanged. Hazards Hazard by a bursting hose assembly. A hazard may originate from fragments flying around. Hazard by a leaking hose assembly. Leaking media, especially if emerging in a very thin jet, may cause severe cuts and even cut off limbs. Hot media may lead to scalding. Admixtures to the water may cause irritations and burns. Hazard by a hot medium inside the hose assembly. Touching the hot surface of the hose assembly may lead to severe burns. Hazard by the alteration of the length of the hose assembly. High-pressure hose assemblies shorten under pressure. This can make the operator lose his stability, and the hose assembly may lose its operational safety. Hazard by hose fittings and components joining hose assemblies. Hazards may originate from hose fittings and components joining hose assemblies if these become unfastened, break off or are pulled out as this may lead to an uncontrollable lashing movement of the hose assembly (whip effect). Hazard by hoses lying about. Hoses lying about create a potential stumbling hazard.
Page 1 of 5
2. Intended purpose SPIR STAR High-pressure hose is thought for applications with water using pressure sources with low pulsation rates ( 5%). The following working temperatures are allowed: Product series In general Series HT Series PPA Series F*) Allowed working temperatures -30C to +60C -20C to +150C -20C to +80C -70C to +200C
*) The max. allowable working pressure of the product series F decreases by 5% in the temperature range between 24C and 100C, by 10% in the range between >100C and 150C, and by 20% in the range between >150C and 200C If SPIR STAR High-pressure hoses are to be used with aggressive media like alkaline solutions and acids for example, it is necessary to send a written inquiry on the resistance to SPIR STAR Druckschluche AG before using them. If SPIR STAR High-pressure hoses are to be used with gaseous media, a safety factor of 1:6 between working pressure and burst pressure is to be observed. In this case the outer cover of the hose has to be pricked (perforated) every 10 mm with a suitable device or a spring-actuated prick punch. The maximum working pressure given on the ferrules must not be exceeded under any circumstances. This applies also to pressure peaks.
Page 2 of 5
Wrong
Right
Comment
At installing, make sure that the required length exists to avoid "buckling" and tensioning of the hose during operation. The recommended minimum bend radius must not be exceeded. This can be achieved by using a bend restrictor. The bending of a hose may begin only after a length of 1.5 x d.
Twisting the hose during installation and operation, e.g. by blocking a rotary joint or installing the hose under a torsional load, must be avoided by all means.
Because of their outer cover hoses have a certain abrasion resistance, but a hose may not be pulled over sharp edges because this may cause considerable damage to the hose.
Hose assemblies must be protected against damage that may lead to abrasion and cracking and thus to an early failure of the hose.
Page 3 of 5
Wrong
Right
Comment
Hose assemblies must not be bent exceeding the permitted bend radius. The figures for the minimum bend radius given in our catalogue refer to the inflexible laying of hose assemblies. In such cases elbow pieces or bends should be used. The bend of the hose may only start after a length of 1.5 x d.
A twist of the hose assembly through movement should be avoided because of torsional loads acting on the valve or the tube cross section which might lead to failures.
Hose assemblies must be protected against the effect of temperatures if these exceed the values given in the catalog. Particular attention should be paid to the laying of hose assemblies in the range of heat sources. Hose assemblies should be protected by protecting equipment such as protecting hose.
The development of hose loops must be avoided and counteracted. Tensile forces by pulling at those loops are also to be avoided.
Driving over unprotected hose assemblies with vehicles is not permitted. Ramps or similar are specifically to be used if driving over is necessary.
Page 4 of 5
Wrong
Right
Comment
Hose assemblies must not be installed under tension or pressure in the axial direction. You need working space where a lengthening and shortening may occur during use. In such cases, elbow pieces or bends are to be used. The bend of the hose may start only after a length of 1.5 x d.
Based on these examples, it is not possible to display all kinds of faulty or correct installing. In particularly difficult installation conditions, please contact SPIR STAR Druckschluche AG. In exceptional cases of application, special tests may be needed before selecting the hose. 4. Packing and Storage If stored properly (in a dry place, at 23C, no direct solar radiation etc.), SPIR STAR High-pressure hose and fittings can be stored indefinitely. After a storage period of more than 12 months, ready made hose assemblies should be pressure tested at 1.5 times the working pressure but not more than 4.000 bar for 3 minutes in an appropriate pressure test stand before using them. If storing the hose assembly at temperatures near the freezing point, it must be emptied completely (danger of frost). 5. Duration of Use The duration of the use of SPIR STAR High-pressure hose assemblies depends very much on the respective operating conditions. For that reason it is not possible to make a general statement.
Page 5 of 5
Dos: Treat high-pressure hose with extreme caution. SPIR STAR hoses are wire reinforced hoses and should be treated with the same care as a high-pressure containment vessel. When using hoses for water jetting, read and understand Recommended practices for the Use of Manually Operated High-pressure Water jet Equipment (Water jet Technology Association [+1/314-241-1445, www.wjta.org]) Always visually inspect for frayed, damaged or wear spots before using. Check the hose end connections and threads for wear, rust, cracks, mechanical abuse or other deterioration that could produce a dangerous projectile. Know the working pressures and burst pressures of all hoses before using them. Always use clean, filtered water to prolong hose life. Some plants water sources are high in sulphur, which may attack stainless steel. Always clean, drain and coil hoses after use. Soap and water usually provide an excellent cleaning agent. Always wear protective gloves, eyewear and garments when handling high-pressure hose and water jet lances.
Donts: Never use a hose with cuts or wire showing through the outer cover. Never use a hose that has been kinked. Dont use a hose that has bubbles or blisters in the outer cover. Dont exceed the bend radius and pressure rating for each hose. Dont run over or crush the hose with heavy vehicles. Dont use a hose with corroded or leaking end connections. Take it out of service immediately. Dont use hoses that have been exposed to chemical attack or over temperature. Avoid using dirty water or water with sulphur compounds in it. Tests have documented that hoses fail more rapidly when using water sources from chemical plants and refineries. Dont bend the hose over scaffolding or pull heavy equipment with the hose. Dont let the hose support its own weight off towers or buildings. Dont apply torque to the hose assembly. Dont expect water jetting or hydraulic hose to last forever.
Be Safe Replace!
Page 1 of 1
WP
Hose Type
WP
Hose Type
WP
Waterblast
heat exchanger tube cleaning
0 to 500 bar WP
ID 25 25/2 440 bar 6.380 psi
Page 1 of 15
WP
Hose Type
WP
Hose Type
WP
Waterblast
surface preparation (concrete removal, surface cleaning of buildings, paint removal)
0 to 500 bar WP
ID 25 25/2 440 bar 6.380 psi
Page 2 of 15
WP
Hose Type
WP
Hose Type
WP
Waterblast
tank and vessel cleaning
Page 3 of 15
WP
Hose Type
WP
Hose Type
WP
Waterblast
ultra high-pressure waterjet cutting and hydro demolition (cutting and demolition of armoured concrete, pipelines, paper or steel)
Hydraulic
torque wrenching
Page 4 of 15
WP
Hose Type
WP
Hose Type
WP
Hydraulic
bolt tensioning
Page 5 of 15
WP
Hose Type
WP
Hose Type
WP
Hydraulic
pressure test equipment (valves, tooling and control panels)
0 to 500 bar WP
ID 25 25/2 440 bar 6.380 psi
Page 6 of 15
WP
Hose Type
WP
Hose Type
WP
Hydraulic
pressure test equipment (valves, tooling and control panels)
Page 7 of 15
WP
Hose Type
WP
Hose Type
WP
Hydraulic
hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
0 to 500 bar WP
ID 25 25/2KM 345 bar 5.000 psi
Page 8 of 15
WP
Hose Type
WP
Hose Type
WP
Hydraulic
hydraulic tools (instrumentation packages for gauges, control of service equipment, hydraulic jacks, hydraulic tools)
Hydraulic
hydroforming
Page 9 of 15
WP
Hose Type
WP
Hose Type
WP
0 to 500 bar WP
ID 25 25/2KM 345 bar 5.000 psi
Page 10 of 15
WP
Hose Type
WP
Hose Type
WP
Page 11 of 15
WP
Hose Type
WP
Hose Type
WP
0 to 500 bar WP
ID 25 25/2KM 345 bar 5.000 psi
Page 12 of 15
WP
Hose Type
WP
Hose Type
WP
0 to 500 bar WP
ID 25 25/2 440 bar 6.380 psi 25/2KM 345 bar 5.000 psi
Page 13 of 15
WP
Hose Type
WP
Hose Type
WP
0 to 500 bar WP
ID 25 25/2KM 345 bar 5.000 psi
Page 14 of 15
WP
Hose Type
WP
Hose Type
WP
Page 15 of 15
3 bar 7 bar
25 mm 0,984 inch
ID Flow
3 l/min 5 l/min 10 l/min 15 l/min 20 l/min 30 l/min 40 l/min 50 l/min 100 l/min 150 l/min 200 l/min 300 l/min 500 l/min
3 mm 0,118 inch
4 mm 0,157 inch
5 mm 0,197 inch
6 mm 0,236 inch
8 mm 0,315 inch
10 mm 0,394 inch
203 psi 667 psi 1349 psi 2234 psi 4540 psi
464 psi 769 psi 1581 psi 2611 psi 3845 psi
319 psi 667 psi 1102 psi 1624 psi 5439 psi
174 psi 276 psi 406 psi 1392 psi 2828 psi 4670 psi
145 psi 479 psi 972 psi 1624 psi 3292 psi
145 psi 276 psi 464 psi 943 psi 2306 psi
13 mm 0,512 inch
ID Flow
0,5 gal/min 1 gal/min 3 gal/min 4 gal/min 5 gal/min 8 gal/min 10 gal/min 15 gal/min 25 gal/min 40 gal/min 50 gal/min 80 gal/min 150 gal/min
3 mm 0,118 inch
4 mm 0,157 inch
5 mm 0,197 inch
6 mm 0,236 inch
8 mm 0,315 inch
10 mm 0,394 inch
42 psi 288 psi 477 psi 705 psi 1604 psi 2370 psi
122 psi 202 psi 299 psi 680 psi 1005 psi 2043 psi 4995 psi
51 psi 76 psi 173 psi 255 psi 518 psi 1267 psi 2885 psi
60 psi 88 psi 179 psi 438 psi 996 psi 1472 psi 3352 psi
52 psi 127 psi 290 psi 428 psi 975 psi 2928 psi
These pressure drop figures refer to a hose of 30 ft length. The medium is water at a temperature of 70 F. In the part of the table marked red the flow velocity exceeds 15 m/s. This information is supplied without liability.
Seite 1 von 1
- worldwide
Companies
Germany SPIR STAR Druckschluche AG Auf der Rut 3 64668 Rimbach (Mitlechtern) Phone: Fax: E-Mail: Web: +49 (0) 6253-9889-0 +49 (0) 6253-9889-33 info@spirstar.de www.spirstar.de USA SPIR STAR Ltd. 10002 Sam Houston Center Drive Houston, Texas, 77064 Phone: Fax: E-Mail: Web: +1 (0) 281-664-7800 +1 (0) 281-664-7850 info@spirstar.com www.spirstar.com France SPIR STAR France 6, rue Clment Ader ZA de lArodrome 67500 Haguenau Phone: Fax: E-Mail: Web: +33 (0) 388-9322 23 +33 (0) 388-9322 24 spirstar@spirstar.fr www.spirstar.fr Asia SPIR STAR ASIA PTE Ltd. 16 Kian Teck Drive Singapore, 628833 Phone: Fax: E-Mail: Web: +65 (0) 6-265 3011 +65 (0) 6-264 1165 sales@spirstarasia.com www.spirstarasia.com
Hightech
made in Germany
00031306