Está en la página 1de 14

Hilti HIT-MM PLUS Concrete applications

Hilti HIT-MM PLUS Adhesive Anchor System


Injection mortar system
-

Benefits
chemical injection fastening two-component hybrid mortar rapid curing suitable for overhead fastenings versatile and convenient handling clean and simple in use small edge distance and anchor spacing - always correct mixing ratio - in-service temperatures: short term: max. 80C long term: max. 50C

Hilti HIT-MM PLUS 330 ml foil pack 500 ml foil pack

Mixer HIT RE-M Rebar, acc. EN 1992-1-1 Ann. C Threaded rods: HIT-V HAS

HIS-N sleeve

Dispenser: Hilti MD 2000 Hilti MD 2500 Hilti ED 3500-A

Concrete

Basic loading data (for a single anchor)


Data in this section applies to Non-cracked concrete C20/25, fck,cube = 25 N/mm Load values valid for holes drilled with TE rotary hammers in hammering mode. Diamond coring is not permitted Embedment depth, base material thickness given in table page 2 Correct anchor setting (see instruction for use, setting details) No edge distance and spacing influence Base material temperature during installation and curing must be between 0C through +40C In-service temperate range: min base material temperature -40C max. long term/short term base material temperature: +24C/40C

08 / 2009

Hilti HIT-MM PLUS Concrete applications

Recommended loads for tension loading: non-cracked concrete C 20/25


The data provided in the following table is intended for product comparison only and not suitable for the complete design of an anchorage. Threaded rods - size Drill bit diameter Embedment depth Tensile load Rebar - size Drill bit diameter Embedment depth Tensile load d0 hef Nrec [mm] [mm] [mm] [kN] d0 hef Nrec [mm] [mm] [mm] [kN] 8 12 80 130 5,0 M8 10 80 110 5,0 10 14 90 150 7,0 M10 12 90 130 7,0 12 16 110 170 10,0 M12 14 110 150 10,0 13 18 125 180 11,0 14 18 125 190 11,5 M16 18 125 196 12,0 16 20 145 210 12,0

Base material thickness h

Base material thickness h

Materials
Material quality steel elements
Part Rebar Threaded rod HIT-V, HAS-(E) Threaded rod HIT-V-R, HAS-(E)R Internal threaded sleeve a) HIS-N Internal threaded sleeve a) HIS-RN Washer ISO 7089 Nut EN ISO 4032 a) b) Material Refer to EN 1992-1-1 Annex C Table C.1 and C.2N Strength class 5.8, EN ISO 898-1, A5 > 8% ductile steel galvanized 5 m, EN ISO 4042 Stainless steel grade A4, A5 > 8% ductile strength class 70,EN ISO 35061, EN 10088: 1.4401; 1.4404; 1.4578; 1.4571; 1.4439; 1.4362 C-steel 1.0718, EN 10277-3 Steel galvanized 5m EN ISO 4042 Stainless steel 1.4401 and 1.4571 EN 10088 Steel galvanized, EN ISO 4042; Stainless steel, EN 10088: 1.4401; 1.4404; 1.4578; 1.4571; 1.4439; 1.4362 Strength class 8, ISO 898-2 steel galvanized 5 m, EN ISO 4042 Strength class 70, EN ISO 3506-2, stainless steel grade A4, EN 10088: 1.4401; 1.4404; 1.4578; 1.4571; 1.4439; 1.4362

related fastening screw: strength class 8.8 EN ISO 898-1, A5 > 8% Ductile steel galvanized 5m EN ISO 4042 related fastening screw: strength class 70 EN ISO 3506-1, A5 > 8% Ductile stainless steel 1.4401; 1.4404; 1.4578; 1.4571; 1.4439; 1.4362 EN 10088

Setting
Installation equipment
Anchor size Rotary hammer Other tools M6 M8 M10 M12 TE2 TE16 blow out pump, set of cleaning brushes, dispenser

08 / 2009

Hilti HIT-MM PLUS Concrete applications

Setting instruction Dry and water-saturated concrete, hammer drilling

12

13

14

15

13

14

08 / 2009

Hilti HIT-MM PLUS Concrete applications

Setting details
Marking of the embedment depth

d0

df

Bore hole depth h0 = anchorage depth hef Thickness of concrete member h

Fixture Thickness tfix

Setting details: Threaded Rod


Anchor size M8 Nominal diameter of drill bit Effective anchorage depth Minimum base material thickness Diameter of clearance hole in the fixture Minimum spacing Minimum edge distance Torque moment d0 hef hmin df smin cmin Tmax [mm] [mm] [mm] [mm] [mm] [mm] [Nm] 10 80 110 9 40 40 10 Threaded Rod M10 M12 12 90 130 12 50 50 20 14 110 150 14 60 60 40 M16 18 125 196 18 80 80 80

Setting details: Rebar


Anchor size
8 10 12

Rebar
13 14 16

Nominal diameter of drill bit Effective embedment and drill hole depth range a) for rebar Minimum base material thickness Minimum spacing Minimum edge distance

d0 hef hmin smin cmin

[mm] [mm] [mm] [mm] [mm]

12 80

14 90

16 110

18 120

18 125

20 145

hef + 50 mm 40 40 50 50 60 60 65 70 70 80 80 100

08 / 2009

Hilti HIT-MM PLUS Concrete applications

Setting details: Internal threaded sleeve HIS-N / HIS-RN


hS

d0

Anchor size Nominal diameter of drill bit Diameter of element Effective anchorage depth Minimum base material thickness Diameter of clearance hole in the fixture Thread engagement length; min - max Torque moment a) Minimum spacing Minimum edge distance

Bore hole depth h0 = Embedment depth hef

M8x90 d0 d hef hmin df hs Tmax smin cmin [mm] [mm] [mm] [mm] [mm] [mm] [Nm] [mm] [mm] 14 12,5 90 120 9 8-20 10 40 40

M10x110 18 16,5 110 150 12 10-25 20 45 45

df

M12x125 22 20,5 125 170 14 12-30 40 55 55

08 / 2009

Hilti HIT-MM PLUS Masonry applications

Hilti HIT-MM PLUS Adhesive Anchor System


Injection mortar system Benefits
- chemical injection fastening for all type of base materials: - hollow and solid - clay bricks, sand-lime bricks, normal and light weight concrete blocks, aerated light weight concrete, natural stones - two-component hybrid mortar - rapid curing - versatile and convenient handling - flexible setting depth and fastening thickness - small edge distance and anchor spacing - mortar filling control with HIT-SC sleeves - suitable for overhead fastenings - in-service temperatures: short term: max.80C long term: max. 50C

Hilti HIT-MM PLUS 330 ml foil pack 500 ml foil pack

Mixer HIT-V rods HAS rods HAS-E rod HIT-AC rod HIT-ACR rod HIT-AN rod HIT-IG internal threaded sleeve HIT-IC internal threaded sleeve HIS-N, HIS-RN internal threaded sleeve HIT-SC composite sleeve Dispenser: Hilti MD 2000 Hilti MD 2500 Hilti ED 3500-A

Solid brick

Hollow brick

08 / 2009

Hilti HIT-MM PLUS Masonry applications

Basic loading data (for a single anchor)


All data in the table below applies to Load values valid for holes drilled with TE rotary hammers in hammering mode Correct anchor setting (see instruction for use, setting details) Steel quality of fastening elements: see data below Steel quality for screws for HIT-IG, HIT-IC and HIS-N: min. grade 5.8 / HIS-RN: A4-70 Threaded rods of appropriate size (diameter and length) and a minimum steel quality of 5.6 can be used Base material temperature during installation and curing must be between -5C through +40C (Exception: solid clay bricks (e.g. Mz12): +5C till 40C)

Recommended loads Frec for pull-out failure in [kN]


The data provided in the following table is intended for product comparison only and not suitable for the complete design of an anchorage.

Solid masonry: HIT-MM PLUS with HIT-AC / HAS and HIT-IG / HIT-IC HIT-AC, HAS, HAS-E
Anchor size Base material Solid clay brick Mz12/2,0 DIN 105/ EN 771-1 fb a) 29 N/mm Setting depth [mm] M8 M10 M12 M8 M10 M12

HIT-IG / HIT-IC

80

Frec [kN]

0,9

1,5

1,5

0,9

1,5

1,5

Hollow masonry: HIT-MM PLUS with HIT-SC and HIT-AC / HAS and HIT-IG / HIT-IC HIT-AC, HAS, HAS-E
Anchor size Base material Hlz 12 DIN 105/ EN 771-1 fb a) 12 N/mm Setting depth [mm] M8 M10 M12 M8

HIT-IC / HIT-IG
M10 M12

HIT-SC HIT-SC HIT-SC HIT-SC HIT-SC HIT-SC HIT-SC HIT-SC 16x 16x 18x 22x 16x 18x 22x 22x

80

Frec [kN]

0,8

0,8

0,8

0,8

0,8

0,8

0,8

0,8

a)

fb = brick strength

Due to the wide variety of bricks site tests have to be performed for determination of load values for all applications outside of the above mentioned base materials and / or setting conditions.
08 / 2009

Hilti HIT-MM PLUS Masonry applications

Materials
Material quality Threaded Rod
Part Threaded rod HIT-V, HAS-(E) Threaded rod HIT-V, HAS-(E)R HIT-AC rod HIT-ACR rod HIT-AN rod HIT-IG sleeve HIT-IC sleeve HIS-N HIS-RN Washer ISO 7089 Nut EN ISO 4032 HIT-SC sleeve Material Strength class 5.8, EN ISO 898-1, A5 > 8% ductile steel galvanized 5 m, EN ISO 4042 Stainless steel grade A4, A5 > 8% ductile strength class 70,EN ISO 35061, EN 10088: 1.4401; 1.4404; 1.4578; 1.4571; 1.4439; 1.4362 Carbon steel grade 5.8; galvanized to min. 5 m Stainless steel, grade A4-70; 1.4401; 1.4404; 1.4571 Carbon steel grade 3.6; galvanized to min. 5 m Carbon steel 1.0718; galvanized to min. 5 m Carbon steel; galvanized to min. 5 m C-steel 1.0718, EN 10277-3, Steel galvanized 5m EN ISO 4042 Stainless steel 1.4401 and 1.4571 EN 10088 Steel galvanized, EN ISO 4042; Stainless steel, EN 10088: 1.4401; 1.4404; 1.4578; 1.4571; 1.4439; 1.4362 Strength class 8, ISO 898-2 steel galvanized 5 m, EN ISO 4042 Strength class 70, EN ISO 3506-2, stainless steel grade A4, EN 10088: 1.4401; 1.4404; 1.4578; 1.4571; 1.4439; 1.4362 PA/PP

Setting
Installation equipment
Anchor size Rotary hammer Other tools M6 M8 M10 M12 TE2 TE16 blow out pump, set of cleaning brushes, dispenser

08 / 2009

Hilti HIT-MM PLUS Masonry applications

Setting instruction in solid base material

08 / 2009

Hilti HIT-MM PLUS Masonry applications

Setting details: hole depth h0 and effective anchorage depth in solid base materials

Setting details HIT-AC, HIT-V, HAS, HAS-E, HAS-R


Anchor size M8 Nominal diameter of drill bit Effective anchorage depth Hole depth Minimum base material thickness Diameter of clearance hole in the fixture Minimum spacing Minimum edge distance Torque moment Filling volume d0 hef h0 hmin df smin cmin Tinst [mm] [mm] [mm] [mm] [mm] [mm] [mm] [Nm] [ml] 10 80 85 115 9 100 100 5 4 HIT-AC, HIT-V M10 M12 12 80 85 115 12 100 100 8 5 14 80 85 115 14 100 100 10 7 M8 10 80 85 110 9 100 100 5 4 HAS, HAS-E, HAS-R M10 M12 12 90 95 120 12 100 100 8 6 14 110 115 140 14 100 100 10 10 M16 18 125 130 170 18 100 100 10 15

10

08 / 2009

Hilti HIT-MM PLUS Masonry applications

HIT-IG, HIT-IC

HIS-N/RN

Setting details HIT-IG, HIT-IC


Anchor size M8 Nominal diameter of drill bit Effective anchorage depth Hole depth Minimum base material thickness Diameter of clearance hole in the fixture Length of bolt engagement Minimum spacing Minimum edge distance Torque moment Filling volume d0 hef h0 hmin df hS smin cmin Tinst [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [Nm] [ml] 14 80 85 115 9 HIT-IG M10 18 80 85 115 12 M12 18 80 85 115 14 M8 14 80 85 115 9 HIT-IC M10 16 80 85 115 12 M12 18 80 85 115 14 HIS-N/RN M8 M10 M12 14 90 95 120 9 18 110 115 150 12 22 125 130 170 14

min. 10 max. 75 100 100 5 6 100 100 8 6 100 100 10 6

min. 10 max. 75 100 100 5 6 100 100 8 6 100 100 10 6

min. 8 min. 10 min 12 max.20 max.25 max.30 100 100 100 100 5 6 100 8 10 100 10 16

08 / 2009

11

Hilti HIT-MM PLUS Masonry applications

Setting instruction in hollow base material

12

08 / 2009

Hilti HIT-MM PLUS Masonry applications

Setting details: hole depth h0 and effective anchorage depth in hollow base materials HAS / HIT-AC with HIT-SC HIT-AC, HIT-V, HAS

Setting details HAS / HIT-A with sieve sleeve


Anchor size Sieve sleeve HIT SC Nominal diameter of drill bit Effective anchorage depth Hole depth Minimum base material thickness Diameter of clearance hole in the fixture Minimum spacing a) Minimum edge distance a) Torque moment Filling volume M6 M8 M10 M12 12x50 12x85 16x50 16x85 16x50 16x85 18x50 18x85 22x50 22x85 d0 hef h0 hmin df smin cmin Tinst [mm] [mm] [mm] [mm] [mm] [mm] [mm] [Nm] [ml] 12 50 60 80 7 100 100 3 12 12 80 95 115 7 100 100 3 24 16 50 60 80 9 100 100 3 18 16 80 95 115 9 100 100 3 30 16 50 60 80 12 100 100 4 18 16 80 95 115 12 100 100 4 30 18 50 60 80 14 100 100 6 18 18 80 95 115 14 100 100 6 36 22 50 60 80 14 100 100 6 30 22 80 95 115 14 100 100 6 55

08 / 2009

13

Hilti HIT-MM PLUS Masonry applications

Setting details: hole depth h0 and effective anchorage depth in hollow base materials HIT-IG / HIT-IC with HIT-SC

HIT-IG / HIT-IC

Setting details HIT-IG / HIT-IC with sieve sleeve


Anchor size Sieve sleeve HIT SC Nominal diameter of drill bit Effective anchorage depth Hole depth Minimum base material thickness Diameter of clearance hole in the fixture Length of bolt engagement Minimum spacing Minimum edge distance Torque moment Filling volume M8 16x85 d0 hef h0 hmin df hS smin cmin Tinst [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [Nm] [ml] 100 100 3 30 16 80 95 115 9 HIT-IG M10 22x85 22 80 95 115 12 min. 10 max. 75 100 100 4 45 100 100 6 45 100 100 3 30 M12 22x85 22 80 95 115 14 M8 16x85 16 80 95 115 9 HIT-IC M10 18x85 18 80 95 115 12 min. 10 max. 75 100 100 4 36 100 100 6 45 M12 22x85 22 80 95 115 14

14

08 / 2009

También podría gustarte