Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Capacity
Rated capacity (kg) 750 900 1050 1200 1350 1600 1800 2000 2250 2500 3000
and Speed
Number of persons 10 12 14 16 18 21 24 26 30 33 40 Rated speed (m/sec) 2.0 2.5 3.0 3.5 4.0 5.0 6.0 7.0
: Applicable
Control,
Number of elevators in a bank
: Not applicable
8.0
9.0
Notes: 1. Capacity and number of persons are based on EN81-1 (1998). 2. Please consult our local subcontractor for specifications outside the table above. 3. The specifications in green frame ( ) are for the space saving models. 4. Refer to page 5 to 12 for the hoistway and machine room layout plans for the models with specifications marked in gray ( For the layouts for models with other specifications, please consult our local subcontractor.
Notes: * 1. When the capacity and speed exceed the range shown in the left page, the operation system 2C-2BC should be 2C-AI-22. * 2. Please consult our local subcontractor, when 2C-AI-22 system is required instead of 2C-2BC system. ).
Notes: *1 Please consult our local subcontractor if the maximum travel exceeds the values specified in the table above. *2 For some elevator specifications, the floor height (distance between floors) must be a minimum of 2500mm. Please consult us if the floor height is less than Entrance height HH + 700mm.
The system consists of call buttons in the car, and a riser of up and down destination floor buttons installed at each elevator hall (single button at terminal floors), which connect electrically with microprocessors supervising floor selection and direction of travel. A car will respond to those car and hall calls that comply with its direction of service. When there are no more calls registered for the car's direction of travel, the car's service direction is reversed.
100-125 R1 AM (min)
Car frame height (HB) according to car design and car depth
Car frame height (HB) (mm) 3450 3650 Car designs S10 S20 S30 N10 N20 BB1400 BB1400 N30 N40 N50 N60 N70 N80
BB BH
BM (min)
Note: The dimensions HB are calculated when the ceiling height (HL) is 2300mm and without the emergency exit on ceiling. Please consult our local subcontractor if required the emergency exit.
JJ AA AH
R2
(Unit: mm)
(Unit: mm)
Control panel
Control panel
Attachment panel
Regulation EN81-1
Hoistway
Intercom (option)
Machine room
3.0
2500
(Unit: kN)
Pit-depth (PD) *2
Travel TR (m) TR100 2.0 100TR120 120TR150 TR100 2080 750
(Unit: mm)
Rated capacity (kg) 900 1050 1200 1350 1600 2080 2800 3000 3020
Overhead-height (OH) *2
Travel TR (m) TR100 2.0 100TR120 120TR150 TR100 5290 5440 5640 5790 Rated capacity (kg) 750 900
(Unit: mm)
Hoisting hook or trolley beam (by owner)
1600
HM (min.) Cinder-concrete finish (by owner)
5360
TC
2.5
2.5
5440
OH (min.) Entrance height: HH=2100
3.0
100TR120 120TR150
3.0
Highest floor
Code number
1-unit 2-unit 3-unit 4-unit installation installation installation installation 4 units Width x Depth Width x Depth Width x Depth Width x Depth Width AM x BM AM x BM AM x BM AM x BM AM 2350 x 3455 4200 x 3455 6200 x 3455 8200 x 3455 2350 x 3455 4350 x 3455 6550 x 3455 8750 x 3455 2350 x 3655 4350 x 3655 6550 x 3655 8750 x 3655 2500 x 3655 4750 x 3655 7150 x 3655 9550 x 3655 4200 4350 4350 4750
Width x Depth Width x Depth Width x Depth Width x Depth Width x Depth AA x BB AH x BH AH x BH AH x BH AH x BH 2.0 2.5 P 10 P 12 2.0 2.5 3.0 P 14 P 16 P 18 P 21 750 900 1050 1200 1350 1600 10 12 14 16 18 21 800 900 900 1000 1100 1100 1400 x 1300 2000 x 2050 3900 x 2050 5900 x 2050 7900 x 2050 1600 x 1300 2300 x 2050 4300 x 2050 6500 x 2050 8700 x 2050 1600 x 1500 2300 x 2250 4300 x 2250 6500 x 2250 8700 x 2250 1800 x 1500 2500 x 2250 4700 x 2250 7100 x 2250 9500 x 2250 2000 x 1500 2700 x 2250 5100 x 2250 7700 x 2250 10300 x 2250 2000 x 1700 2700 x 2450 5100 x 2450 7700 x 2450 10300 x 2450
2700 x 3655 5150 x 3655 7750 x 3655 10350 x 3655 5150 2700 x 3855 5150 x 3855 7750 x 3855 10350 x 3855 5150
Notes: * 1. All the above dimensions are calculated based on EN81-1 (1998). * 2. The dimensions PD, OH and BH are calculated when the counterweight without safety gear is located in back of the car. * 3. These machine room depth BM with a facing arrangement should be (2BH+3500) mm when lobby width is 3.5m. * 4. The dimensions shown are minimum requirements, particularly in the figures of TC, OH and PD. Necessary tolerance should be separately considered for the building construction errors. * 5. The dimensions TC, OH, PD and reaction load are calculated according to car and hoistway dimensions on the above table and conditions.
TravelTR
Number of persons
Total height
HL
P1
Note: The dimensions OH are calculated when the car frame height (HB) is 3450mm.
HB
P2
100TR150
Hoistway section
6
Car frame height (HB) according to car design and car depth
Car frame height (HB) (mm) 3450 Car designs S10 S20 S30 N10 N20 BB1400 BB1400 N30 N40 N50 N60 N70 N80
BB
BH
Attachment panel
Control panel
Control panel
Control panel
Elevator lobby
Attachment panel
Control panel
Control panel
Control panel
Intercom (option)
AH
R2
3650
Note: The dimensions HB are calculated when the ceiling height (HL) is 2300mm and without the emergency exit on ceiling. Please consult our local subcontractor if required the emergency exit.
Power outlet (by owner) Power receiving box (by owner) Lighting outlet (by owner)
(Unit: mm)
(Unit: mm)
BH
Hoistway
Machine room
(Unit: kN)
Pit-depth (PD) *2
Travel TR (m) TR100 3.5 100TR120 120TR150 4.0 TR150 3570 750
(Unit: mm) Rated capacity (kg) 900 1050 1200 1350 1600 3020 3370 3570 3590 3920
Overhead-height (OH) *2
Travel TR (m) TR100 3.5 100TR150 4.0 TR150 6120 750
6520
OH (min.)
Highest floor
Width x Depth Width x Depth Width x Depth Width x Depth AA x BB AH x BH AH x BH AH x BH 3.5 P 12 P 14 3.5 4.0 P 16 P 18 P 21 900 1050 1200 1350 1600 12 14 16 18 21 900 900 1000 1100 1100 1600 x 1300 4400 x 2100 6650 x 2100 8900 x 2100 1600 x 1500 4400 x 2300 6650 x 2300 8900 x 2300 1800 x 1500 4800 x 2300 7250 x 2300 9700 x 2300 2000 x 1500 5200 x 2300 7850 x 2300 10500 x 2300 2000 x 1700 5200 x 2500 7850 x 2500 10500 x 2500
Width x Depth Width x Depth Width x Depth Width AM x BM AM x BM AM x BM AM 4400 x 3455 6650 x 3455 8900 x 3455 4400 x 3655 6650 x 3655 8900 x 3655 4800 x 3655 7250 x 3655 9700 x 3655 5200 x 3655 7850 x 3655 10500 x 3655 5200 x 3855 7850 x 3855 10500 x 3855 4400 4400 4800 5200 5200
P2
P1
Travel (TR)
Code number
Number of persons
Total height
HL P1
Notes: * 1. All the above dimensions are calculated based on EN81-1 (1998). * 2. The dimensions PD, OH and BH are calculated when the counterweight without safety gear is located in back of the car. * 3. These machine room depth BM with a facing arrangement should be (2BH+3500) mm when lobby width is 3.5m. * 4. The dimensions shown are minimum requirements, particularly in the figures of TC, OH and PD. Necessary tolerance should be separately considered for the building construction errors. * 5. The dimensions TC, OH, PD and reaction load are calculated according to car and hoistway dimensions on the above table and conditions.
Hoistway section
HB P2
TC
Note: The dimensions OH are calculated when the car frame height (HB) is 3450mm.
Car frame height (HB) dimensions according to car design and car depth
Car frame height (HB) (mm) Car designs S10 S20 S30 N10 N20 N30 N40 N50 N60 N70 N80
BB
BH
3600 4000
AH
R2
Group control panel
Reactor panel Control panel Reactor panel Control panel
Elevator lobby
Reactor panel
Control panel
Reactor panel
Control panel
Reactor panel
Control panel
Note: The dimensions HB are calculated when the ceiling height (HC) is 2300mm and without the emergency exit on ceiling. Please consult our local subcontractor if required the emergency exit.
(Unit: mm)
(Unit: mm)
150TR200 3600
Hoistway
Machine room
2800
(Unit: kN)
(Unit: mm)
(Unit: mm)
Hoisting hook or trolley beam (by owner)
150TR200 225 155 260 235 5.0 3950 4250 5.0 6800 7200
HM (min.)
Number of persons
Internal dimensions of hoistway (mm) *2 In-line arrangement 2-unit installation 3-unit installation 4-unit installation
2-unit 3-unit 4-unit installation installation installation 4 units 6 units 8 units Width x Depth Width x Depth Width x Depth Width AM x BM AM x BM AM x BM AM 5500 x 3800 8100 x 3800 10700 x 3800 5500 5700 x 3800 8500 x 3800 11300 x 3800 5700 5700 x 4050 8500 x 4050 11300 x 4050 5700 TR150 5800 x 4150 8700 x 4150 11600 x 4150 5800 Width AM 8100 8500 8500 8700 8800 Width AM 10700 11300 11300 11600 11700
Total height
Width x Depth Width x Depth Width x Depth Width x Depth AA x BB AH x BH AH x BH AH x BH P 16 P 18 P 21 P 24 1200 1350 1600 1800 16 18 21 24 1000 1100 1100 1100 1800 x 1450 5100 x 2300 7700 x 2300 10300 x 2300 2000 x 1450 5500 x 2300 8300 x 2300 11100 x 2300 2000 x 1700 5500 x 2550 8300 x 2550 11100 x 2550 2100 x 1750 5700 x 2650 8600 x 2650 11500 x 2650
150TR200 5900 x 4150 8800 x 4150 11700 x 4150 5900 Notes: * 1 All the above dimensions are calculated based on EN81-1 code (1998). * 2 The dimensions BH are calculated when the counterweight is equipped without safety gear. * 3 These are the machine room width dimensions with a facing arrangement and a lobby width of 3.5m. * 4 The dimensions shown are minimum requirements, particularly in the figures of TC, OH and PD. Necessary tolerance should be separately considered for the building construction errors. * 5 TC, OH, PD and reaction load are calculated according to car and hoistway dimensions on the above table. (When the counterweight is back drop.) * 6 The shaft independently housing a single car is not recommended because noise increases. Please consult our local subcontractor if the shaft of that kind is required.
P2
P1
Travel (TR)
HL P1
Hoistway section
HB P2
OH (min.)
TC
Note: The dimensions OH are calculated when the car frame height (HB) is 3600mm.
10
Car frame height (HB) dimensions according to car design and car depth
Car frame height (HB) (mm) 3600 Car designs S10 S20 S30 N10 N20 N30 N40 N50 N60 N70 N80
BB
BH
4000
Reactor panel
Control panel
Reactor panel
Control panel
Reactor panel
Control panel
Elevator lobby
Reactor panel
Control panel
Reactor panel
Control panel
Reactor panel
Control panel
AH
R2
Note: The dimensions HB are calculated when the ceiling height (HC) is 2300mm and without the emergency exit on ceiling. Please consult our local subcontractor if required the emergency exit.
(Unit: mm)
(Unit: mm)
150TR200 3600
Hoistway
Machine room
2800
(Unit: kN)
(Unit: mm)
(Unit: mm)
Hoisting hook or trolley beam (by owner)
150TR200 225 155 260 235 6.0 3950 4250 6.0 6800 7200
HM (min.)
Number of persons
Internal dimensions of hoistway (mm) *2 In-line arrangement 2-unit installation 3-unit installation 4-unit installation
2-unit 3-unit 4-unit installation installation installation 4 units 6 units 8 units Width x Depth Width x Depth Width x Depth Width AM x BM AM x BM AM x BM AM 5800 x 3800 8400 x 3800 11000 x 3800 5800 5700 x 3800 8500 x 3800 11300 x 3800 5700 5700 x 4050 8500 x 4050 11300 x 4050 5700 TR150 5800 x 4150 8700 x 4150 11600 x 4150 5800 Width AM 8400 8500 8500 8700 8800 Width AM 11000 11300 11300 11600 11700
Total height
Width x Depth Width x Depth Width x Depth Width x Depth AA x BB AH x BH AH x BH AH x BH P 16 P 18 P 21 P 24 1200 1350 1600 1800 16 18 21 24 1000 1100 1100 1100 1800 x 1450 5100 x 2300 7700 x 2300 10300 x 2300 2000 x 1450 5500 x 2300 8300 x 2300 11100 x 2300 2000 x 1700 5500 x 2550 8300 x 2550 11100 x 2550 2100 x 1750 5700 x 2650 8600 x 2650 11500 x 2650
150TR200 5900 x 4150 8800 x 4150 11700 x 4150 5900 Notes: * 1 All the above dimensions are calculated based on EN81-1 code (1998). * 2 The dimensions BH are calculated when the counterweight is equipped without safety gear. * 3 These are the machine room width dimensions with a facing arrangement and a lobby width of 3.5m. * 4 The dimensions shown are minimum requirements, particularly in the figures of TC, OH and PD. Necessary tolerance should be separately considered for the building construction errors. * 5 TC, OH, PD and reaction load are calculated according to car and hoistway dimensions on the above table. (When the counterweight is back drop.) * 6 The shaft independently housing a single car is not recommended because noise increases. Please consult our local subcontractor if the shaft of that kind is required.
P2
P1
Travel (TR)
HL P1
Hoistway section
11
HB P2
OH (min.)
TC
Note: The dimensions OH are calculated when the car frame height (HB) is 3600mm.
12
13
14