Documentos de Académico
Documentos de Profesional
Documentos de Cultura
This device complies with Part 15 of the FCC Rules. Operation shall be subject to the following two conditions: (1) This device may not cause harmful interface, and (2) This device must accept any interface received, including interface that may cause undesirable operation. This equipment has been tested and complied with the limits for a Class a digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interface when the equipment is operated under a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interface to radio communications. Operation of this equipment in a residential area is likely to cause harmful interface in which case the user will be required to correct the interface at his own expenses. Note: All brands and trademarks shall belong to their respective owner. Note: Specification is subject to changes without notice.
Introduction
Installation- Keyboard Wedge
1) 2) 3) 4) 1) 2) 3) First of all, you must switch off power for the terminal/computer. Disconnect the keyboard cable from the back of the terminal/computer. Connect the appropriate interface cable to the scanner and to the terminal/computer. Turn the terminal/computer power on. Disconnect power to the terminal/computer. Connect the appropriate interface cable and external power supply (DC adapter) to the scanner. Plug the serial connector into the serial port on the back of your computer/terminal. Tighten the two screws to secure the connector to the port. Plug the power pack into power source. Once the scanner has been fully connected, turn the terminal/computer power back on. Connect the USB cable between scanner and PC. Windows will automatically detect the USB device.
RS-232
4) 5)
Note: If any of the above operation is incorrect, turn off the power immediately and check any improper connections. Go through all above steps again. Note: If you need more programming parameters to setup your ArgoScan scanner, please go to www.argox.com and download the completed users manual.
Interface Selection
Keyboard Wedge
RS-233
USB
Note:-Default
Keyboard Layout
USA *
Belgium
Danish
Germany
Italian
Portuguese
Spanish
Swedish
Switzerland
UK
Latin American
Japanese
RTS/CTS
Xon/Xoff
ACK/NAK
600 BPS
1200 BPS
2400 BPS
4800 BPS
9600 BPS *
38400 BPS
Odd
Even
7 bits
Pin Assignments
AS Series 8-pin RJ-45 Connector Pin 1 2 3 4 5 6 7 8 RS-232 VCC (+5V) TXD NC NA CTS RXD RTS GND Keyboard VCC (+5V) NC CLK / PC DATA / PC DATA / KB NC CLK / KB GND 1 2 3 4 5 6 7 8 9 10 10-pin
1 2 3 54 6 7 8 8-pin AS Series 10-pin RJ-45 Connector Pin 1 2 3 4 5 6 7 8 9 10 RS-232 I/F VCC (+5V) TXD NC GND CTS RXD RTS GND NC
Keyboard I/F VCC (+5V) NC CLK / PC DATA / PC DATA / KB NC CLK / KB GND GND
Keyboard Wedge Combo Connector (To Host Side): Pin 1 2 3 4 5 6 4 3 2 1 6 4 2 5 Mini-DIN 6P Male DATA / PC NC GND VCC (+5V) CLK / PC NC DIN 5P Female Connector DIN 5P Female DATA / KB NC GND VCC (+5V) CLK / KB NC
RS-232 DB-9F Connector (To Host Side): Pin 1 2 3 4 5 6 7 8 9 Definition NC TXD RXD NC GND NC CTS RTS VCC (+5V) 5 4 3 2 1 9 8 7 6
Keyboard Wedge PS/2 Connector (To Host Side): Pin 1 2 3 4 5 6 4 2 1 3 6 Mini-DIN 6P Male DATA / PC NC GND VCC (+5V) CLK / PC NC Mini-DIN 6P Female DATA / KB NC GND VCC (+5V) CLK / KB NC
5 6 4 2 1
Scan Mode
Good-read off
Momentary *
Alternate
Timeout off
Continue
Test only
Tab
None
10
Enable Barcode
Industrial 2 of 5
Matrix 2 of 5 Eur
Standard 2 of 5
Codabar
Code 93
Code 11
MSI/Plessey
UK/Plessey
Telepen
China Post
11
RSS-Limited
RSS-Expanded
Micro-PDF (for 8312) Note: All other barcodes not listed in the table are set to be enabled in default.
12
2 digits
5 digits
UCC/EAN 128
Auto detection
13
2 digits
5 digits
2, 5 digits
UCC/EAN 128
2, UCC/EAN 128
5, UCC/EAN 128
All
14
2 digits
5 digits
UCC/EAN 128
Auto detection
15
2 digits
5 digits
2, 5 digits
UCC/EAN 128
2, UCC/EAN 128
5, UCC/EAN 128
All
16
UPCA Truncation/Expansion
None *
Expand to EAN-13
UPCE Truncation/Expansion
None *
Expand to EAN-13
Expand to UPCA
UPCE Expansion
None *
17
2 digits
5 digits
UCC/EAN 128
Auto detection
18
2 digits
5 digits
2, 5 digits
UCC/EAN 128
2, UCC/EAN 128
5, UCC/EAN 128
All
19
2 digits
5 digits
UCC/EAN 128
Auto detection
20
2 digits
5 digits
2, 5 digits
UCC/EAN 128
2, UCC/EAN 128
5, UCC/EAN 128
All
21
ISBN/ISSN Conversion
Disable *
Enable
EAN-8 Expansion
None *
22
Verification Enable
Transmit Disable *
Transmit Enable
Full ASCII
Append Disable *
Append Enable
Start/End Tx Disable *
Start/End Tx Enable
23
CODE-11 PARA
CODE-128 PARA *
CODE-39 PARA *
CODE-93 PARA
EAN-13 PARA *
24
PDF-417
(8250/8312 *)
STANDRAD-25 PARA
CODE-16K
INDUSTRIAL-25 PARA
UPCE PARA *
25
INTERLEAVED-25 PARA *
MATRIX 25 PARA
MSI/PLESSEY PARA
UPCA PARA *
UK/PLESSEY PARA
GS1 Databar
Micro-PDF (8312 *)
26
!#"$&%'()0 21 5 6 7A3 B93C GIHP4 BIQR6 G$WX BIQ S CWX BIQ Y CiHpW BIQIc CI7Es 7$tvu txQxu G'yv7 C'W CI3 Qtp7 G 4W C 3F G9A CiGIQ W FF FG Qxd RG GIH dIG G AIG q r t Q B C F s 4 y { 3 7 T H V @ | X z f g e w }
w i k
s d G W A `
8 a U u q
y ~ u
B CI3
27
Barcode standard parameter setting list If you wish to display the current configuration of your AS-8110/8120/8150/8250/8310/8312, scanner over the host terminal/computer, scan the Barcode standard parameter setting list bar code.
Unique parameter list If you wish to display the unique parameter setting list, scan the unique parameter list bar code
System parameter setting list If you wish to display the product information and revision number for your AS-8110/8120/8150/8250/8310/8312 scanner over the host terminal/computer, scan the System parameter setting list bar code.
String setting list If you wish to display the string format list, scan the String setting list bar code.
28
Exit
Program
Firmware version list If you wish to display the firmware version, scan the Firmware version list barcode.
Exit
Program
WARNING: Default value initialization If you wish to return the AS-8110/8120/8150/8250/8310 to all the factory default settings, scan the Default value initialization bar code.
29
0 A 1 B 2 C 3 D 4 E 5 F 6
8 Finish 9
30