Documentos de Académico
Documentos de Profesional
Documentos de Cultura
AII 36651
INSTALLATION TRAILER HITCH 2008 RIDGELINE
Issue Date
INSTRUCTIONS MAY 2007
PARTS LIST
6 Bolts, 12 x 40 mm
Control unit
2 Bolts, 10 x 30 mm
2 Plain washers, 10 mm
6 Spring washers, 12 mm
Subfuse box upper cover
2 Spring washers, 10 mm
3 Fuses, 20A
Receiver cover
2 Fuses, 7.5A
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36651 (0705) 08L92-SJC-1010-91 1 of 11
Wire tie with clip TOOLS AND SUPPLIES REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Ratchet
10 mm, 14 mm, 16 mm, 17 mm, and 18 mm Socket
5 Flange bolts, 6 x 16 mm
Torque wrench
10 mm, 14 mm, and 16 mm Combination wrench
Diagonal cutters
Connector clip Illustration of the Trailer Hitch Installed on the
Vehicle
CONTROL UNIT
Socket bracket
RELAY
TRAILER
HITCH
2 Flange nuts, 6 mm
2 Flange bolts, 6 x 35 mm
4914040H
SOCKET
3 Relays
INSTALLATION
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
Control unit harness should not be attempted by “do-it-yourselfers.”
1. Make sure you have the anti-theft code for the
radio, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
Owner’s manual
2 of 11 AII 36651 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved.
Installing the Control Unit 5. Install the control unit into the unit bracket. Do not
push on the connector area.
3. Remove the left dashboard side cover (seven
clips).
UNIT BRACKET
7 CLIPS
CONTROL UNIT
LEFT
DASHBOARD
SIDE COVER CONNECTOR AREA
(Do not push on the
3916011T connector area.)
4223012H
VEHICLE
SELF-TAPPING
CONNECTORS
SCREW
CONTROL UNIT
HARNESS RELAY
BLOCK
TUBE
5804010S
DRIVER'S 9 CLIPS
DASHBOARD
LOWER COVER
3916021T
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36651 (0705) 3 of 11
7. Plug the control unit harness 12-pin connector into 11. Under the dashboard on the driver’s side of the
the control unit. vehicle, install the unit bracket to the vehicle
frame with one 6 x 16 mm flange bolt.
CONTROL UNIT
HARNESS 6 x 16 mm
CONNECTOR CLIP FLANGE BOLT
STEERING
SHAFT
SQUARE
HOLE
UNIT
BRACKET
VEHICLE
FRAME
UNIT
BRACKET
CONTROL UNIT
5804020S
CONTROL UNIT HARNESS
12-PIN CONNECTOR
5804040S
8. Push the connector clip on the control unit 6 x 16 mm UNIT
FLANGE BOLT BRACKET
harness into the square hole in the unit bracket.
9. On the right side of the steering shaft, locate the 12. Install the relay block on the control unit harness
vehicle 10-pin and 4-pin connectors (if equipped) to the unit bracket.
blue taped to the vehicle harness. Remove the
blue tape to free the connectors. NOTE: If the vehicle is produced prior to August
24, 2005, untape the 4-pin connector from the 10-
NOTE: Vehicles produced prior to August 24, 2005 pin connector, and tape the 4-pin connector to the
will not be equipped with the 4-pin connector. 12-pin control unit harness.
RELAY BLOCK
OF CONTROL
BLUE-TAPE
UNIT HARNESS
(Remove.)
10-PIN
CONTROL UNIT CONNECTOR
HARNESS
4-PIN
CONNECTOR
UNIT
BRACKET
RELAY BLOCK
OF CONTROL
5804030S
UNIT HARNESS
10. Plug the vehicle 10-pin and 4-pin connectors (if 4-PIN
equipped) into the control unit harness 10-pin and CONNECTOR
4-pin connectors.
4 of 11 AII 36651 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved.
Attaching the Relay Securing the Vehicle 10-Pin Connector
13. Using a flat-tip screwdriver through the hole in the 15. Under the rear bumper on the left side, locate the
side of the dashboard, remove the vehicle relay vehicle 10-pin connector taped to the vehicle
block as shown. harness. Remove the green tape to free the
connector.
NOTE: Failure to disconnect the negative battery
cable may cause the VTM-4 20 amp (#4) fuse to
WIRE TIE
blow. The VTM-4 fuse is located in the auxiliary WITH CLIP
under hood fuse box.
VEHICLE
FLAT-TIP HARNESS
SCREWDRIVER
REAR
VEHICLE
BUMPER
RELAY BLOCK
145 mm
VEHICLE
RELAY
BLOCK
Push.
VEHICLE
10-PIN
GREEN TAPE CONNECTOR
UP (Remove.)
VEHICLE
VEHICLE
RELAY 4223044H
BRACKET 4N12011H
BLOCK
14. Install a relay into the vehicle relay block, and 16. Measure from the end of the harness, and attach
reinstall the vehicle relay block. one wire tie with clip to the vehicle harness as
shown.
RELAY
VEHICLE
RELAY
BLOCK
4N12020H
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36651 (0705) 5 of 11
17. Push the wire tie with clip into the hole in the 20. With the help of an assistant, position the trailer
vehicle frame. hitch under the vehicle, and loosely install six 12
x 40 mm bolts with six 12 mm plain washers and
six 12 mm lock washers.
VEHICLE
WIRE TIE
FRAME
WITH CLIP 21. Loosely install two 10 x 36 mm bolts with two 10
mm plain washers and two 10 mm lock washers
to secure the center of the trailer hitch.
• First torque the 10 x 36 mm bolts at the center
of the hitch to 46 N·m (4.6 kgf·m 34 lbf·ft), then
torque the 12 x 40 mm bolts at the ends of the
hitch to 80 N·m (8.2 kgf·m, 59 lbf·ft).
TRAILER 3 12 mm PLAIN
EXHAUST HITCH WASHERS 3 12 mm LOCK
PIPE WASHERS
4223051H
TRAILER
HITCH
2 10 mm BOLTS
46 N·m
(4.6 kgf·m, 34 lbf·ft)
2 10 mm PLAIN
3 12 mm PLAIN
WASHERS
WASHERS
BACK
EXHAUST
COVER
2 10 mm LOCK
3007013H WASHERS
12 mm BOLT 3 12 mm LOCK
4 BOLTS
80 N·m WASHERS 3007024H
(8.2 kgf·m, 59 lbf·ft)
6 of 11 AII 36651 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved.
23. Slide the ball mount into the trailer hitch. Align the 26. Route the harness from the socket through the
holes in the trailer hitch with the holes in the ball opening in the trailer hitch, and install the socket
mount, then insert the hitch pin into the hole. bracket to the trailer hitch with two 6 x 16 mm
Secure the hitch pin with the hitch pin clip. flange bolts.
TRAILER HITCH
HITCH PIN
CLIP
CONCAVE
TRAILER
HITCH
TRAILER HITCH SOCKET
BRACKET
HITCH PIN BALL MOUNT
6 x 16 mm
4223061H FLANGE BOLT
SOCKET 4223073H
HARNESS
Installing the Socket
24. Install the 10-pin socket to the socket bracket
27. Remove the dummy connector from the vehicle
with two 6 x 16 mm flange bolts.
10-pin connector, and plug the socket 10-pin
connector into the vehicle 10-pin connector.
SOCKET
BRACKET
VEHICLE 10-PIN SOCKET 10-PIN SOCKET 10-PIN
CONNECTOR CONNECTOR CONNECTOR
2 6 x 35 mm
FLANGE BOLTS
CONNECTOR
10-PIN CLIP
SOCKET
DUMMY
CONNECTOR
BODY PANEL
COVER
6 x 16 mm
FLANGE
BOLTS 2 6 mm
FLANGE 4-PIN
NUTS SOCKET SOCKET
HARNESS CLIP
CONNECTOR
4-PIN SOCKET
4914082H CLIP 4223085H
25. Remove the cover from the 4-pin socket, and 28. Install the connector clip into the vehicle 10-pin
install the 4-pin socket to the socket bracket with connector, and push the connector clip and socket
two 6 x 35 mm flange bolts and two 6 mm flange harness clip into the holes in the body panel.
nuts. Reattach the cover.
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36651 (0705) 7 of 11
Installing the Fuses 30. Check that all wire harnesses are routed properly
and all connectors are plugged in.
29. Under the hood, remove the subfuse box upper
cover, and install the three 20A fuses and two 31. Reinstall all removed parts. Check that all clips
7.5A fuses into the connectors in the subfuse box. and fasteners are installed securely.
Then install the subfuse box upper cover from the
32. Reconnect the negative cable to the battery.
kit.
33. Reset the clock, and enter the radio station
SUBFUSE BOX SUBFUSE BOX
UPPER COVER UPPER COVER
presets.
(Discard.)
7.5A FUSE 34. Check the operation of the trailer harness
(Late model
vehicles only.) according to the owner’s manual supplied.
20A FUSE
7.5A FUSE NOTE: Whenever the battery is disconnected, the
driver’s window AUTO function is disabled.
35. Start the engine. Push down on the driver’s
window switch until the window is fully open.
36. Pull up on the driver’s window switch fully to close
the window completely, then hold the switch for 2
seconds or more.
37. Test the window AUTO function.
SUBFUSE
BOX
NOTE: After about 620 miles (1,000 km) of use,
Upper side viewed retighten the bolts and nuts to the specified torque.
8 of 11 AII 36651 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved.
Put a Copy of This Page in the Glove Box for Your Customer
Installing the Receiver Cover
Whenever you remove the hitch pin clip, the hitch pin, and the ball mount, securely store them in the cargo area.
Then install the receiver cover into the opening at the end of the trailer hitch. When you reinstall the ball mount, store
the receiver cover in the cargo area.
TRAILER HITCH
RECEIVER COVER
4224010H
TRAILER
BRAKE
SUBHARNESS
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36651 (0705) 9 of 11
CIRCUIT DIAGRAM (Vehicles produced on August 24, 2005 and later)
IG2
6 1 9 7 8
BATTERY (20A) (7.5A) (20A) (20A) (7.5A)
ORG
AT BLK
SWITCH
REVERSE RED / GRN
BLK
GRN / GRN / WHT
BLU RED
BLK
CONVERTER UNIT
YEL BRN BLU WHT WHT RED GRN BLK
WHT
BLK
YEL
RED
GRN BRN GRN
BLK
SMALL +B
SOCKET 4-PIN
LIGHT
CONNECTOR
RIGHT 5804070S
TURN / STOP
LEFT BRN
TURN / BACK
STOP LIGHT BLK BLACK BRN BROWN
ELEC YEL YELLOW ORN ORANGE
GND BRAKE
BLU BLUE PUR PURPLE
10 of 11 AII 36651 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved.
CIRCUIT DIAGRAM (Vehicles produced prior to August 24, 2005)
6 9 7 8
BATTERY (20A) (20A) (20A) (7.5A)
RED / BLU
BRAKE CONTROL RIGHT
CONNECTOR SMALL TURN
CHARGE
LIGHT
RELAY
BLK RELAY
BRN / WHT / BLK
WHT BRN LEFT
STOP SWITCH BLK BLK TURN
GRN GRN / BLK
WHT / BLK
BLK
RED / GRN
GRN / RED BLK GRN / WHT
WHT
BLK
BRN
RED
GRN YEL GRN
BLK
+B
SMALL SOCKET 4-PIN
4D20101H
LIGHT CONNECTOR
RIGHT
TURN / STOP
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36651 (0705) 11 of 11