Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Pgina 1 de 15
Desarmado y Armado
D8R Series II Track-Type Tractor Power Train
Nmero de medio -RENR3677-04 Fecha de publicacin -01/10/2007 Fecha de actualizacin -25/10/2007
i01433695
Assembly Procedure
Table 1 Required Tools Tool A B C D Part Number 138-7573 3K-4897 6V-4072 138-7575 8S-5132 3B-1915 6V-8801 5M-2894 E 1B-9575 1D-4716 4B-5270 4B-5271 F G FT-2214 H 8T-5096 Adapter Dial Indicator Group 1 1 6V-4980 6V-4980 Bolt (5/16 inch by 18 by 1 3/4 inch) Nut (5/16 inch by 18) Washer (0.083 inch by 0.88 inch) Washer (2 mm by 25.5 mm) Torque Screwdriver Torque Screwdriver 1 1 2 2 1 1 Description Link Bracket Spring Pin Spanner Wrench Link Bracket Plate Bolt (3/8 inch by 16 by 1 3/8 inch) Nut (3/8 inch by 16) Washer (2.5 mm by 18.5 mm) Qty 2 8 1 3 1 3 3 6
Note: O-ring seals, gaskets, and seals should always be replaced. A used O-ring may not have the same sealing properties as a new O-ring seal. A reconditioning procedure should not be degraded because of a low cost component such as an O-ring seal or a gasket. Use 1U-6396 O-Ring Assembly Compound during the assembly procedure.
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 2 de 15
Ver imagen
Illustration 1
g00619498
1. Install retaining ring (64) and spacer (66) in brake housing (39) . 2. Lower the temperature of bearing cups (63) and (65) . 3. Install the bearing cups in brake housing (39) .
Ver imagen
Illustration 2
g00619496
Note: If bearing cone (62) was removed from housing (38), a new bearing must be installed. 4. Heat bearing cone (62) to a maximum temperature of 135 C (275 F). 5. Install bearing cone (62) on housing (38). Make sure that bearing cone (62) is seated on housing (38) .
Ver imagen
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 3 de 15
Illustration 3
g00619518
Note: The brake housing weighs 150 kg (335 lb). 6. Use a hoist and tool (D) to position brake housing (39) on housing (38) . 7. Heat bearing cone (61) to a temperature of 135 C (275 F). 8. Install bearing cone (61) on housing (38) . 9. Install plate (49) and three bolts (46) . 10. Install tool (G) on plate (49). Do not install the shims at this time. 11. Position brake housing (39) on wood blocks in order to raise housing (38) off the floor.
Ver imagen
Illustration 4
g00619522
12. Use tool (G) to rotate housing (38) . 13. Use tool (F) to measure the bearing preload. Tighten three bolts (46) equally until the proper preload is reached. The bearing preload should be 3 1 Nm (28 8 lb in).
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 4 de 15
Ver imagen
Illustration 5
g00619526
14. When the bearing preload is correct, use a feeler gauge to measure the gap between the housing and plate (49) in three places. Average the three measurements in order to determine the correct shim pack thickness. 15. Remove three bolts (46) and plate (49) . 16. Position the correct shim pack and plate (49) on the housing. 17. Install three bolts and washers (46) . 18. Tighten three bolts to a torque of 47 9 Nm (35 7 lb ft). 19. Use tool (G) to recheck the bearing preload. 20. Install the three remaining bolts and washers (46) . 21. Tighten the three remaining bolts (46) to a torque of 47 9 Nm (35 7 lb ft).
Ver imagen
Illustration 6
g00619494
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 5 de 15
22. Install shuttle valve (67) and O-ring seal (59) in the brake housing.
Ver imagen
Illustration 7
23. Position ring (55) and spring (56) in brake housing (39) . 24. Install ring (60) on piston (57) . 25. Install seal ring (58) in piston (57). See Illustration 7. Apply clean oil to the lip of the seal ring. 26. Install piston (57) in the brake housing. 27. Install seal ring (53) in retainer (50). See Illustration 7. Apply clean oil to the lip of the seal ring. 28. Position retainer (50) on piston (57). Align the oil passage in retainer (50) with the oil passage and O-ring seal (59) in the brake housing. 29. Install six bolts and washers (45) .
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 6 de 15
30. Position thrust washer (54) on retainer (50) . 31. Install four friction discs (43) and the three brake plates. Alternate the friction discs and the brake plates. 32. Install ring (44) in hub (48) . 33. Position hub (48), thrust washer (51), and retainer (52) . 34. Install three bolts and washers (42) .
Ver imagen
Illustration 8
g00619491
Note: Brake housing (39) weighs 150 kg (335 lb). 35. Use a hoist and tool (D) to position brake housing (39) on final drive housing (41) . 36. Install two bolts and washers (40) .
Ver imagen
Illustration 9
g00619490
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 7 de 15
37. Position gear (37) on housing (38) . 38. Install eighteen bolts and washers (36) .
Ver imagen
Illustration 10
g00619489
39. Position shim pack (35) and support bracket (34) on the brake housing. 40. Install twelve bolts and washers (33) .
Ver imagen
Illustration 11
g00619488
41. Lower the temperature of bearing cups (32) . 42. Install bearing cups (32) in carrier (29) .
Ver imagen
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 8 de 15
Illustration 12
g00619537
43. Heat two bearing cones (30) to a maximum temperature of 135 C (275 F). 44. Install one bearing cone (30) on pinion (24) . 45. Position carrier (29) on pinion (24) . 46. Install remaining bearing cone (30) on pinion (24) .
Ver imagen
Illustration 13
g00622039
47. Install washer (25), lock washer (26), and nut (28) on the pinion (24). Install the large chamfered end of nut (28) toward the lock washer (26) . 48. Position pinion (24) in a soft jawed vise. 49. Use tool (C) to tighten nut (28) and preload the bearings.
Ver imagen
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 9 de 15
Illustration 14
g00622040
50. Position carrier (29) on two wood blocks. 51. Use tool (F) to measure the bearing preload. The correct bearing preload is 0.80 0.50 Nm (7.0 4.5 lb in). 52. Bend a tang of lock washer (26) in one of the four slots in nut (28) .
Ver imagen
Illustration 15
g00622041
53. Position the pinion and carrier (29) on support bracket (34) . 54. Install the bolt and the washer (27) .
Ver imagen
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 10 de 15
Illustration 16
g00622042
55. Use tool (H) to check the backlash of pinion (24). Measure the backlash at three equally spaced teeth on pinion (24). Average the three measurements. The correct backlash is 0.210 0.075 mm (0.0083 0.0030 inch). If necessary, remove support bracket (34) in order to add or remove shims from shim pack (35) .
Ver imagen
Illustration 17
g00622052
Ver imagen
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 11 de 15
Illustration 18
g00622053
57. Position planetary gear (21) and discs (23) in planetary carrier (15) . 58. Install shaft (19) in planetary carrier (15) . 59. If the rubber in pin (20) is damaged, replace the pin. 60. Align the hole in shaft (19) with the hole in planetary carrier (15) . 61. Install pin (20). Install the pin so that the end of the pin is even with the surface of planetary carrier (15) . 62. Repeat Steps 56 through 61 for the two remaining planetary gears. 63. Install the retaining ring in planetary carrier (15) . 64. Use tool (B) to compress the retaining ring. 65. Slide planetary carrier (15) in ring gear (6) . 66. Remove tool (B) .
Ver imagen
Illustration 19
g00622054
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 12 de 15
67. Position gear (18) and plate (17) on the carrier. 68. Install three bolts (16) .
Ver imagen
Illustration 20
g00622055
Ver imagen
Illustration 21
g00622061
Ver imagen
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 13 de 15
Illustration 22
g00622064
71. Position gear (11) and discs (13) in planetary carrier (7) . 72. Install shaft (8) . 73. If the rubber in pin (10) is damaged, replace the pin. 74. Align the hole in shaft (8) with the hole in planetary carrier (7) . 75. Install pin (10) until the end of the pin is even with the surface of the carrier. 76. Repeat Steps 70 through 75 for the three remaining planetary gears. 77. Install seal ring (9) on planetary carrier (7) .
Ver imagen
Illustration 23
g00622066
78. Install planetary carrier (7) in ring gear (6) . 79. Install the thrust ring and retaining ring (5) . 80. Apply 6V-6640 Sealant to the flange of slinger (4). Position slinger (4) on the planetary carrier.
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 14 de 15
Ver imagen
Illustration 24
g00622067
Note: The carrier assembly weighs 48 kg (105 lb). 82. Install a hoist and tool (A) . 83. Position sliding carrier (3) in the housing. 84. Remove tool (A) .
85. Install two remaining bolts (2) . 86. Install three equally spaced bolts and washers (1) . End By: Install the left hand final drive, the steering differential, and the brake. Refer to Disassembly and Assembly, "Final Drive, Steering Differential, and Brake (Left Side) - Install" in
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010
Pgina 15 de 15
this module.
Copyright 1993 - 2010 Caterpillar Inc. Todos los derechos reservados. Red privada para licenciados del SIS.
https://sis.cat.com/sisweb/sisweb/techdoc/content.jsp?calledpage=/sisweb/sisweb/pro...
26/08/2010