Documentos de Académico
Documentos de Profesional
Documentos de Cultura
AMPreVA 5.0
AMPreVA 5.0
Reference Manual
TECHNOSOFT INC.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
1
TECHNOSOFT INC.
AMPreVA 5.0
TECHNOSOFT INC.
11180 Reed Hartman Highway
Cincinnati, OH 45242
Copyright 2014 by TechnoSoft Inc.
All rights reserved.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any
form or by means, electronic, mechanical, photocopying, recording, or otherwise, without
written permission of TechnoSoft Inc. Information contained herein is solely for your
information and is not offered or to be construed as a warranty or contractual obligation.
Questions and comments: ampreva_support@technosoft.com
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
2
TECHNOSOFT INC.
AMPreVA 5.0
Introduction ............................................................................................................................. 6
2.2
2.3
2.4
2.5
2.6
Canvas ............................................................................................................................ 10
4.1.1
4.1.2
4.1.3
4.1.4
Drawings ................................................................................................................. 25
4.1.5
Manufacturing ......................................................................................................... 25
4.2
4.2.1
4.2.2
4.2.3
4.2.4
4.3
Shell................................................................................................................................ 33
4.3.1
4.3.2
4.3.3
4.3.4
Head ........................................................................................................................ 40
4.3.5
4.3.6
4.3.7
Packed Bed.............................................................................................................. 54
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
3
TECHNOSOFT INC.
4.4
Support ........................................................................................................................... 55
4.4.1
Legs ......................................................................................................................... 56
4.4.2
Skirt ......................................................................................................................... 67
4.4.3
4.4.4
Saddle...................................................................................................................... 80
4.5
Nozzle............................................................................................................................. 89
4.5.1
Rings............................................................................................................................. 100
4.7
4.7.1
4.7.2
4.7.3
4.7.4
4.7.5
4.7.6
4.7.7
4.7.8
4.7.9
4.7.10
Access........................................................................................................................... 129
4.8.1
4.8.2
4.8.3
4.9
4.9.1
4.9.2
4.9.3
+Nozzle ................................................................................................................... 89
4.6
4.8
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
4
TECHNOSOFT INC.
6.1
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
5
TECHNOSOFT INC.
AMPreVA 5.0
1 Introduction
AMPreVA is an application software for Pressure Vessels and Heat Exchangers layout and
fabrication detailing. AMPreVA incorporates a feature-based modeling environment enabling
the rapid layout and configuration of tanks. AMPreVA automates the creation of the 3D solid
models, fabrication details, drawing, bill of material along many other details required to design
and fabricate a tank. For the purpose of simplifying the terminology as used in this document we
will refer to a Pressure Vessel or a Heat Exchanger as tank.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
6
TECHNOSOFT INC.
AMPreVA 5.0
2 Modeling Environment
The AMPreVA modeling environment supports a graphical user interface (GUI) incorporating a
set of toolbars, menus, a graphic canvas, a message pane, and a model tree. This GUI facilitates
the rapid creation of the tank model. This model can be created either from imported design data
or interactively through the GUI by selecting the features and setting the appropriate properties
and dimensions.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
7
TECHNOSOFT INC.
AMPreVA 5.0
The GUI toolbar provides similar options to the menu toolbar. Only the marked buttons shown
in the Figure 3 are critical to the initial use of AMPreVA. The first marked button is used to
create a new model. The second marked button is used to save a model. The third marked
button is used to retrieve a saved model.
The other buttons under the Menu Bar as well as the GUI Toolbar that this manual does not
cover provide various functionalities. These functionalities are in general used by advanced
users to support the creation of 1D, 2D, and 3D geometry entities, geometry operations,
dimensions in a similar fashion to a CAD system.
This limited general purpose feature based modeler should not be used for replacing the CAD
system. For the purpose of building and detailing tanks a user should not focus on the use of any
of the capabilities provided in the Menu Bar or the GUI Toolbar that have not been introduced in
this manual.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
8
TECHNOSOFT INC.
AMPreVA 5.0
The model tree area includes the model tree and a menu located below it. The menu enables the
specification of the action of the mouse left button and the mouse right button. The action can be
set pushing the correct icon. The left button action selection includes many options. The most
critical ones that any user should be familiar with are:
1. Edit. Used to set the left action button to invoke the edit menu on the selected object.
2. Draw. Used to set the left action button to draw the selected object.
3. Undraw. Used to set the left action button to undraw the selected object.
The model tree depicts the hierarchy of the tank design components. The mouse buttons can be
used to invoke the appropriate action by selecting the object in the model tree.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
9
TECHNOSOFT INC.
AMPreVA 5.0
2.6 Canvas
The canvas area includes a toolbar located at the top to enable the graphic manipulation of the
geometry, a message pane located at the bottom, and a geometry display at the center.
The graphic toolbar includes a set of buttons organized to facilitate the manipulation of the tank
components displayed in the canvas. The functions of the most common used buttons are listed
below in the order from left to right as shown in the above picture.
1. Edit. Mouse left-click button will enable the interactive selection of a component from
the canvas. Once selected the edit menu is updated
2. Rotate. Mouse left-button click will set the interactive mouse left-button click operations
in the canvas area in rotation mode. Holding the mouse left-button and dragging in the
canvas area will enable the interactive rotation of the view of the components drawn
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
10
TECHNOSOFT INC.
AMPreVA 5.0
3. Pan. Mouse left-button click will set the interactive mouse left-button click operations in
the canvas area in pan mode. Holding the mouse left-button and dragging in the canvas
area will enable the interactive pan of the view of the components drawn
4. Zoom. Mouse left-button click for zoom in, right-button click for zoom out
5. Zoom window. Mouse left click and drag in the canvas for zooming the view about the
window selected area
6. Fit. Mouse left-button click to view all the drawn objects in the canvas
7. XY and XY view
8. YX and YX view
9. ZY and ZY view
10. YZ and YZ view
11. XZ and XZ view
12. ZX and ZX view
13. Isometric view. A list of different isometric view can be selected
14. User defined views
15. Editing lights sources
16. Undraw. Mouse left-button click will enable the interactive undrawn of the components
in the canvas. When done with selecting the components to undrawn a right-click will
pop up a menu with the appropriate action to end the operation. A mouse right-button
click will clear the canvas i.e. undrawn all components
17. Object Grouping. Grouping of the drawn object can be organized to enable the
redrawing to components as needed
18. Shade. Mouse left-button click will enable the interactive shading of the components in
the canvas. When done with selecting the components to shade a mouse right-click is
required. A mouse right-button click will enable other shading options
19. Shade. Mouse left-button click will enable the interactive un-shading of the components
in the canvas. When done with selecting the components to un-shade a mouse right-click
is required
20. Transparency. Mouse left-button click will enable the interactive setting of the
transparency of the components in the canvas. When done with selecting the components
to shade a mouse right-click is required
21. Regenerate
22. The use of the remaining buttons above the canvas is in conjunction with other optional
modules and will not be covered in this section
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
11
TECHNOSOFT INC.
AMPreVA 5.0
Once a Pressure Vessel has been initiated a model is created in the model tree as shown in Figure
8. Initially only the geometry node is shown under the top node labeled as Pressure-Vessel0001 in Figure 8. The top node should be selected using the mouse right button and the expand
option should be selected from the popup menu. The model tree is updated to include the nodes
Geometry and Drawings as shown in Figure 8.
The geometry node in the model tree should be selected using the mouse left button. A menu
will pop up as shown in Figure 9. This is the general menu that is used for creating or editing the
components and the features of the Pressure Vessel. At any stage if this menu is closed it can be
reopened by editing (using the mouse left button. Note that the left button action is set to the edit
mode) the geometry node from the model tree.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
12
TECHNOSOFT INC.
AMPreVA 5.0
This form is organized in two areas. A two-row toolbar and a work area with a number of tabs
are highlighted in Figure 9.
The toolbar second row buttons may change based on the selected button from the first row. The
work area and tabs may change based on the selected button in the second row or the selected
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
13
TECHNOSOFT INC.
AMPreVA 5.0
component from the graphic area to edit. Figure 10 toolbar shows in the second row the various
buttons available when the Shell button is selected in the first row. The work area shows the
tab options available when editing the features of a Cylinder component.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
14
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
15
TECHNOSOFT INC.
AMPreVA 5.0
The general form for layout and editing of the tank components is organized to enable setting the
general project information and operating condition data for the tank, adding new components,
and editing component features and properties.
As illustrated in the previous section, to display this Component Layout and Editing Form edit
the geometry object (node) from the model-tree. The Edit options should be selected from the
pull down menu next to the left button action label below the model tree pane.
If certain component is already drawn in the canvas the Component Layout and Editing Form
can be invoked by editing the component from the canvas. The first button above the canvas is
used for interactive editing.
As illustrated Figure 11 the Component Layout and Editing form includes a two row toolbar at
the top (highlighted in red), a general editing form with tabs each containing various buttons or
type in fields (highlighted in blue) used for setting the properties of the component being edited,
and a set of action buttons at the bottom (highlighted in green).
The action buttons at the bottom of the form provide the functionality listed by button as they
appear from left to right in the following table.
Icon
Draws into the graphic area (canvas) the Draws into the graphic area the component
component being edited, and when it is a being edited, and all the subcomponents
components container (such as support legs, under it.
support saddles, etc.) draws all the
subcomponents.
Erases from the graphic area the component Erases from the graphic area the
being edited, and when it is a components component being edited, and all the
container (such as support legs, support subcomponents under it.
saddles,
etc.)
undraws
all
the
subcomponents.
The system expects choosing an object from Theres not action available.
the graphic area by doing a left click on the
component in red, to be selected for edition.
The current interface form will be updated
with the properties of the selected
component.
Shows only the boundaries from the Shows the boundaries from the component
component being edited.
being edited, and all the subcomponents
under it.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
16
TECHNOSOFT INC.
AMPreVA 5.0
Shows as a solid object the component being Shows as a solid object the component
edited.
being edited, and all the subcomponents
under it.
Shows the component being edited as a solid Shows the component being edited and all
object remarking their edges.
the subcomponents under it as solid
objects remarking their edges.
Fits the canvas view to the component being Fits the canvas view to all the drawn
edited and all the subcomponents under it.
objects.
Recalculates the geometries for the drawn Redraws the valid geometries for the
object when they have changed.
drawn objects.
Clears the canvas and draws into it the cross Clears the canvas and draws into it the
sections of the component being edited.
cross sections of the model main
components.
Erases from the canvas the cross sections of Erases from the canvas the cross sections
the component being edited. Useful only of the model main components. Useful
when the previous icon was selected.
only when the previous icon was selected.
Draws into the canvas the internal Draws into the canvas the internal
coordinate system of the component being coordinate systems of the model main
edited.
components.
Erases from the canvas the internal Erases from the canvas the internal
coordinate system of the component being coordinate systems of the model main
edited.
components.
Opens the Print Active Graphic Display Same action as left click.
pop up form where some options need to be
selected before saving the canvas contents
into a .PNG, .BMP, .JPG, .TIFF among
others file types.
For editing the properties, dimension, styles and other attributes of the components features as
provided in the tab forms, different style of GUI widgets are used. These include:
1.
2.
3.
4.
5.
6.
Radio buttons
Check boxes
Pull down menus
Action buttons
Type in fields
Computed fields
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
17
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
18
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
19
TECHNOSOFT INC.
AMPreVA 5.0
Support Type. There are 6 types of supports in the system: Legs, Lugs, Skirt, Saddles, Legs &
Lugs, and None.
Contract/Job Number. Specifies the tank contract or job number.
Project Number. Specifies the project number.
Purchaser Order. Specifies the purchaser order.
Purchaser. Specifies the purchaser name.
Location. Specifies the customer location.
Default Density. Specifies a default density.
Company Name. Specifies the company name.
Company Short Name. Specifies a company short name.
Company Address. Specifies the company address.
Company Location. Specifies the company location.
Company Phone Number. Specifies the company phone number.
Company Fax Number. Specifies the company fax number.
Company Logo. Specifies a company logo.
Title Block. There are various styles.
View Styles. Displays the various title block styles.
Drawn by. Specifies the name of the drawing creator. Only available when Title Block is not
None.
Drawing Date. Specifies the drawing creation date. Only available when Title Block is not
None.
Checked by. Specifies the name of the drawing reviser. Only available when Title Block is not
None.
Checked Date. Specifies the drawing revision date. Only available when Title Block is not
None.
Approved by. Specifies the name of the drawing approver. Only available when Title Block is
not None.
Approved by Date. Specifies the drawing approval date. Only available when Title Block is not
None.
Number of Sheets. Specifies the number of sheets. Availability depends on the title block style.
Show Equipment No. / Show Q.C. Info. Option to display in the drawings either the equipment
number or the quality control data. Available only when Title Block of type 2.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
20
TECHNOSOFT INC.
AMPreVA 5.0
Equipment Number. Specifies the equipment number. Availability depends on the title block
style.
Q.C. Initials. Specifies the initials of the quality control reviewer. Available only when Show
Q.C. Info is selected and Title Block is not None.
Q.C. Date. Specifies the date of the quality control review. Available only when Show Q.C.
Info is selected and Title Block is not None.
Revision Data. Action button that displays a form to fill up the revision data to be displayed in
all the drawings. Only available when Title Block is not None.
Status. Specifies the status to be displayed in all the drawings. Only available when Title Block
is not None.
Display/Hide. Option to display or hide the drawings status previously selected. Only available
when Title Block is not None.
Save Project Data as Default. Action button that allows saving most of the entries, after being
applied, of this tab as default for the new models to be created.
Reset Default Project Data. Action button that retrieves the saved entries of the Project tab.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
21
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
22
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
23
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
24
TECHNOSOFT INC.
AMPreVA 5.0
Display All Insulation Geometry. If selected, the insulation geometry will be drawn when it
exists.
Display All Lining Geometry. If selected, the lining geometry will be drawn when it exists.
4.1.4 Drawings
See Generating Drawings.
4.1.5 Manufacturing
See Generating Reports.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
25
TECHNOSOFT INC.
AMPreVA 5.0
Figure 17 Bevel Common Tab. End-0, End-1, Axial, and Circumferential Intermediate Bevel Details
This menu is commonly used through the application. Some component such as the head may
have only one bevel-end setting and other may have four such in the case of cylinder shells.
Type. There are 12 types of bevel supported by the system: A, B1, B2, B3, B4, B5, B6, C1, C2,
C3, C4, and C5.
Land Length. Specifies the contact distance with the Attach to Component.
Outer Bevel Angle 1. The outer bevel angle. Only valid for types B2, B3, C2, C3, C4, and C5.
Outer Bevel Angle 2. The outer tap angle.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
26
TECHNOSOFT INC.
AMPreVA 5.0
Inner Bevel Angle 1. The inner bevel angle. Only valid for types B5, B6, C1, C3, C4, and C5.
Inner Bevel Angle 2. The inner tap angle.
Outside Bevel Thickness. Specifies the thickness from the land length outer point to the outer
thickness. Only valid for types B3, B4, and C5.
Inside Bevel Thickness. Specifies the thickness from the land length inner point to the inner
thickness. Only valid for types B6, C1, C2, C3, C4, and C5.
Minimum Required Distance. Specifies the minimum required distance.
4.2.1.1 View Bevel Types
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
27
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
28
TECHNOSOFT INC.
AMPreVA 5.0
End Elevation. Specifies the end elevation of the lining. Availability depends on the component
type.
Material. Specifies the material of the lining.
Density. Specifies the density for the selected material.
Weight. Specifies the weight of the lining.
Weight from XML Import. Specifies the weight of the lining when the model was imported from
a XML file.
Present when Empty. If selected, lining will be present when tank is empty.
Present for Hydrotest. If selected, lining will be present for hydrotest.
Include in Lift Weight. If selected, lining will be included in lift weight.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
29
TECHNOSOFT INC.
AMPreVA 5.0
This menu is commonly used through the application and provides the various properties used
for setting the tank design parameters. Most of these values are often imported from the design
software, such in the case of Codeware Compress or PVElite. All fields are appropriately
labeled.
Operating Conditions
Vessel Pressure. Specifies the design pressure.
Vessel Temperature. Specifies the design temperature.
External Pressure. Specifies the external pressure.
External Temperature. Specifies the external temperature.
Inner Corrosion. Specifies the inner corrosion.
Outer Corrosion. Specifies the outer corrosion.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
30
TECHNOSOFT INC.
AMPreVA 5.0
Design Minimum Design Metal Temperature. Specifies the minimum design metal temperature.
Maximum Allowable Working Pressure. Specifies the maximum allowable working pressure.
Maximum Allowable Pressure. Specifies the maximum allowable pressure.
Maximum Allowable External Pressure. Specifies the maximum allowable external pressure.
Minimum Design Metal Temperature. Specifies the rated minimum design metal temperature.
Pipe NPS & Schedule. Specifies the NP Sand Schedule pipes.
Governing Load Condition. Specifies the governing load condition.
Diameter Increase for Wind Loading. Specifies the tank diameter increase for wind.
Required Thickness. Specifies the tank minimum required thickness.
Required Thickness Internal Pressure. Specifies the required thickness for internal pressure.
Required Thickness External Pressure. Specifies the required thickness for external pressure.
Weight and Capacity
Weight New. Specifies the weight.
Weight Corroded. Specifies the tank corroded weight.
Capacity New. Specifies the capacity.
Capacity Corroded. Specifies the tank capacity corroded.
Capacity New (Computed). Specifies the tank capacity computed by the system.
Positions and Dimensions
Start Elevation. Specifies the start elevation from Datum Plane.
End Elevation. Specifies the tank end elevation from Datum Plane.
Start Elevation from Import. Specifies the start elevation coming from the imported model, if
applies.
End Elevation from Import. Specifies the end elevation coming from the imported model, if
applies.
Radiography
Radiography Long Seam. Specifies the radiography process for long seams.
Radiography Circ Seam. Specifies the radiography process for circumferential seams.
Radiography Long Seam Joint Efficiency. Specifies the joint efficiency percentage for long
seams.
Radiography Circ Seam Joint Efficiency.
circumferential seams.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
31
TECHNOSOFT INC.
AMPreVA 5.0
Post Weld Heat Treatment. If selected, indicates that the tank must have a post weld head
treatment.
Impact Tested. If selected, indicates that the tank must be impact tested.
Normalized. If selected, indicates that the tank must be normalized.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
32
TECHNOSOFT INC.
AMPreVA 5.0
4.3 Shell
When the shell button is selected the second row of the toolbar will update to show the various
components available for adding. Each of these components can be added by selecting the
appropriate button from the second row of the toolbar.
Once a button is selected the component is added and the work area in the menu is updated to
enable editing and detailing the component features and properties.
This section describes the various properties than can be edited from the menus that can also be
invoked from the model tree by editing the appropriate component. Each component may have
various properties but only a subset is provided to be modified by the end user in the menu.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
33
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the
cylinder in the BOM.
Attach to Component. Component to which the cylinder is attached to.
Attach to Component End. Selects component end to attach the cylinder.
End to Attach Datum. Selects the cylinder end to the Attach to Component.
Material. Specifies the material of the cylinder.
Density. Specifies the density for the selected material.
Diameter Mode. Enables the selection between OD Design, ID Design and Mid Diameter
Design.
Pipe. If selected, the cylinder will be considered a seamless pipe. If not selected, the cylinder
will be considered as a rolled plate.
Nominal Size. Specifies the cylinder pipe nominal size. Only available when Pipe is selected.
Schedule. Specifies the cylinder pipe schedule. Only available when Pipe is selected.
Inner Diameter. The inner diameter of the cylinder.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
34
TECHNOSOFT INC.
AMPreVA 5.0
Action button that allows the selection of other cylinder to take the
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
35
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the cone
in the BOM.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
36
TECHNOSOFT INC.
AMPreVA 5.0
Flare. If selected, the cone will have a flare in its smallest End. Only available when Reverse
Knuckle is not selected.
Flare Straight Length. Specifies the straight length of the cone flare. Only available when Flare
is selected.
Flare Radius. Specifies the radius of the cone flare. Only valid when Flare is selected.
Flare Apex Angle. Specifies the flare apex angle. Only available when Flare is selected.
Reverse Knuckle. If selected the cone will be created with a reverse knuckle. Only available
when Knuckle and Flare are not selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
37
TECHNOSOFT INC.
Copy Parameters.
dimensions from.
AMPreVA 5.0
Action button that allows the selection of other cylinder to take the
Manufacture Type. Specifies how the Cone is about to be manufactured. Two options are
available: Single Piece, and Multipieces.
Number of Courses. Specifies the number of courses to manufacture the cone. Only available
when Manufacture Type Multipieces is selected.
Courses Radius List [1 to (n-1)]. Specifies the radius of each course, except the last one. The
entry must be in list format. Only available when Manufacture Type Multipieces is selected.
Number of Sections List [1 to n]. Specifies the number of sections for each course. The entry
must be in list format. Only available when Manufacture Type Multipieces is selected.
Initial Angle List [1 to n]. Defines the initial angle of each course. The entry must be in list
format. Only available when Manufacture Type Multipieces is selected.
Segmented Arc-Length List. Shows the arc length of each course.
Manufacture Type Multipieces is selected.
Draw/Undraw Cone Solid Sections. Action button that with a left click draws in the canvas the
cone sections; right click undraws the cone sections from the canvas.
Draw/Undraw Cone Outer Surfaces Sections. Action button that with a left click draws in the
canvas the cone outer surfaces sections; right click undraws the cone outer surfaces sections from
the canvas.
General Arrangement Drawing. Action button that demands the cone segmentations General
Arrangement Drawing.
4.3.2.2 Bevel Tab
See Bevel Common Tab specifications as in Figure 17.
4.3.2.3 Insulation Tab
See Insulation Common Tab specifications as in Figure 19.
4.3.2.4 Lining Tab
See Lining Common tab specifications as seen in Figure 20.
4.3.2.5 Conditions Tab
See Conditions Common Tab specifications as in Figure 21.
4.3.2.6 Flat Pattern and Nesting Tab
See Heads Flat Pattern and Nesting Tab specifications as in Figure 38.
4.3.3 Eccentric Transition
The component edit form has a number of tabs as illustrated Figure 25. The edit area includes
the following Design tab.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
38
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
39
TECHNOSOFT INC.
AMPreVA 5.0
4.3.4 Head
The component edit form has a number of tabs as illustrated Figure 26. The edit area includes
the following tabs Design, Bevel, Insulation, Lining, and NC Program.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
40
TECHNOSOFT INC.
AMPreVA 5.0
End to Attach Datum. Selects the head end to the Attach to Component.
Material. Specifies material of the head.
Density. Specifies the density for the selected material.
Type. There are 10 types of heads supported by the system: Ellipsoidal, F&D, Hemi, Toriconal,
Conical, Welded, Bolted, Dished, Torispherical, and Flat.
Enabled. If selected, the head is included in the 3D geometry, BOM, drawings, and any other
report created by AMPreVA. If deselected it is not included.
Pipe Cap. Defines the head as pipe cap.
Diameter Mode. Enables the selection between OD Design, ID Design and Mid Diameter
Design.
NPS. The diameter nominal size of the head. If custom is selected, user will type in OD or ID.
Sch. The schedule of the head. If custom is selected the user will type in thickness.
Inner Diameter. The straight flange inner diameter of the head.
Outer Diameter. The straight flange outer diameter of the head.
Thickness. The thickness of straight flange area of the head.
Length. The straight flange length of the head.
Crown Radius. The crown radius of the head.
Knuckle Radius. The knuckle radius of the head.
Outer Radius at Knuckle. Specifies the head outer radius at the knuckle.
Knuckle Crown Thickness. Specifies the knuckle thickness, by default is equal to Thickness.
Knuckle ID Offset. Specifies the offset for the knuckle at the head inner diameter. Valid only
when Thickness and Knuckle Crown Thickness are not equal.
Clad Material. If selected, indicates that the head will have clad material.
Clad Material Thickness. The thickness of the material at the inner side of the plate. This is
only valid when Clad Material is selected.
Copy Parameters. Action button that allows the selection of other head to take the dimensions
from.
Manufacture Type. Specifies how the Head is about to be manufactured. Two options are
available: Single Piece, and Multipieces. Only available when Thickness and Knuckle Crown
Thickness are equal, and only for heads of type Ellipsoidal, F&D, Hemi, Torispherical, and Flat.
Number of Courses. Specifies the number of courses to manufacture the head. Only available
when Manufacture Type Multipieces is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
41
TECHNOSOFT INC.
AMPreVA 5.0
Courses Radius List [1 to (n-1)]. Specifies the radius of each course, except the last one. The
entry must be in list format. Only available when Manufacture Type Multipieces is selected.
Number of Sections List [1 to n]. Specifies the number of sections for each course. The entry
must be in list format. Only available when Manufacture Type Multipieces is selected.
Initial Angle List [1 to n]. Defines the initial angle of each course. The entry must be in list
format. Only available when Manufacture Type Multipieces is selected.
Segmented Arc-Length List. Shows the arc length of each course.
Manufacture Type Multipieces is selected.
Draw/Undraw Head Solid Sections. Action button that with a left click draws in the canvas the
head sections; right click undraws the head sections from the canvas.
Draw/Undraw Head Outer Surfaces Sections. Action button that with a left click draws in the
canvas the head outer surfaces sections; right click undraws the head outer surfaces sections from
the canvas.
General Arrangement Drawing. Action button to demand the head segmentations General
Arrangement Drawing.
Figure 27 through Figure 36 shows the various dimension and data input for the different head
types. For some type of heads the form includes additional data associated with the flange area.
For example in the case of ellipsoidal head type additional input are needed and the diameter as
well as the thickness are defined for he flange area of the head.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
42
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
43
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
44
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
45
TECHNOSOFT INC.
AMPreVA 5.0
Course to Edit. Allows the end user to navigate between each course and edit their properties.
3D Section
Weight. Specifies the weight of one heads section for the selected course.
OD Surface Area. Specifies the surface area of one heads section for the selected course.
OD Surface Inner Radial Edge. Specifies the length of the inner radial edge of one heads
section for the selected course.
OD Surface Outer Radial Edge. Specifies the length of the outer radial edge of one heads
section for the selected course.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
46
TECHNOSOFT INC.
AMPreVA 5.0
OD Surface Side Edge. Specifies the length of the side edge of one heads section for the
selected course.
3D Section Min|Max Box Dims
Depth. Specifies the depth of one heads section of the selected course.
Height. Specifies the height of one heads section of the selected course.
Width. Specifies the width of one heads section of the selected course.
Flat Pattern Control Params
Num. of Points Along Profile. Specifies the number of points along the profile to add more
precision.
Num. of Points Along Sweep. Specifies the number of points along the sweep to add more
precision.
Display Section OD Surface. Action button to display on the canvas the outer surface of one
heads section for the selected course.
Display Section Solid. Action button to display on the canvas one heads section for the selected
course.
Display Min|Max Box. Action button to display on the canvas a box with the OD surface
dimensions.
Flat Pattern Section
Weight (no Offset). Specifies the weight of one heads section in flat without offset for the
selected course.
Flat Pattern Area (no Offset). Specifies the surface area of one heads section in flat for the
selected course.
Flat Pattern Inner Radial Edge. Specifies the length of the inner radial edge of one heads
section in flat without offset for the selected course.
Flat Pattern Outer Radial Edge. Specifies the length of the outer radial edge of one heads
section in flat without offset for the selected course.
Flat Pattern Side Edge. Specifies the length of the side edge of one heads section in flat
without offset for the selected course.
Edge Offset. Specifies an extra length to be added to the flat pattern segment.
Weight (with Offset). Specifies the weight of one heads section in flat including the offset for
the selected course.
Nested Pattern Type. There are seven nesting types available for selection.
Sections per Plate Qty. Specifies the number of section to accommodate on each plate. Only
available when Nested Pattern Type is 6 or 8.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
47
TECHNOSOFT INC.
AMPreVA 5.0
Pattern to Plate Edge Clearance. Specifies the clearance between the flat pattern and the edge
of the plate.
Pattern to Pattern Clearance. Specifies the clearance between each flat pattern.
Nested Patterns per Plate Area. Specifies the area of the sections for the bounding plate.
Nested Patterns Bounding Width. Specifies the width for the bounding plate.
Nested Patterns Bounding Length. Specifies the length for the bounding plate.
Nested Patterns Bounding Scrap Area. Specifies the scrap area for the bounding plate.
Nested Patterns Bounding Scrap Rate (%). Specifies the scrap rate in percentage for bounding
plate.
Stock Plate
Plate Width. Specifies the width for the stock plate.
Plate Length. Specifies the length for the stock plate.
Scrap Area. Specifies the scrap area for the stock plate.
Scrap Rate (%). Specifies the scrap rate in percentage for the stock plate.
Display Nested Pattern Types. Action button to display the available nesting patterns.
Display Scrap Data. Action button to display a comparative table with the scrap data between
the available nesting pattern types.
Display Flat Pattern. Action button to display on the canvas the flat pattern of one segment for
the selected course.
Export Flat Pattern DXF. Action button to send into DXF the flat pattern of one segment for the
selected course.
Display Nested Flat Pattern. Action button to display on the canvas one nested pattern for the
selected course.
Export Nested Flat Pattern DXF. Action button to send into DXF one nested pattern for the
selected course.
Flat Pattern Drawing. Action button to demand the flat pattern drawing for the selected course.
4.3.5 Body Flange
The component edit form has a number of tabs as illustrated Figure 39. The edit area includes
the following tabs Design, Welding Neck, Blind, Features Manager, Insulation and Conditions.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
48
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the
flange in the BOM.
Remarks. Optional information or notes regarding the flange, to be display in reports and tables.
Attach to Component. Component to which the flange is attached to.
Attach to Component End. Selects component end to attach the flange.
End to Attach Datum. Selects the flange end to the Attach to Component.
Material. Specifies the material of the flange.
Density. Specifies the density for the selected material.
Type. There are 8 types of flanges supported by the system: Welding Neck, Slip On, Ring,
Threaded, Socket Welded, Lap Joint, Long Weld Neck, and Heavy Barrel.
Code. Specifies the flange code.
Nominal Size. Specifies the nominal size of the flange.
Rating. Specifies the flange class.
Bore Schedule. Specifies the schedule of the flange. Available only when Type Welding Neck is
selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
49
TECHNOSOFT INC.
AMPreVA 5.0
Face Type. There are 6 types of flanges faces supported by the system: Large Raised Face,
Large Lower Face, Small Tongue, Large Tongue, Small Groove, and Large Grove. Available
only when Type Slip-On is selected.
Offset Z Direction. Specifies an offset in the Z axis.
Copy Parameters. Action button that allows the selection of other body flange to take the
dimensions from.
4.3.5.2 Welding Neck Tab
See Nozzle Flange Welding Neck Tab.
4.3.5.3 Slip On Tab
See Nozzle Flange Slip On Tab.
4.3.5.4 Ring Tab
See Nozzle Flange Ring Tab.
4.3.5.5 Threaded Tab
See Nozzle Flange Threaded Tab.
4.3.5.6 Socket Welded Tab
See Nozzle Flange Socket Welded Tab.
4.3.5.7 Lap Joint Tab
See Nozzle Flange Lap Joint Tab.
4.3.5.8 Heavy Barrel Tab
See Nozzle Flange Heavy Barrel Tab.
4.3.5.9 Blind Tab
See Nozzle Flange Blind Tab.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
50
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the tray
assembly in the BOM.
Attach to Component. Component to which the tray assembly is attached to.
Start at Top. If selected, the tray assembly will be set at the Attach to Component top edge. If
not selected, it will be set at the bottom edge.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
51
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
52
TECHNOSOFT INC.
AMPreVA 5.0
Fabrication Type. Specifies the fabrication type for the outer tray supports. It could be Cut from
Plate, or Rolled Flat Bar. Only available when either Pattern Style 1-2 or 2-3 is selected.
Downcomers Properties
Similar Downcomers Between both Styles. If selected, downcomers from second pattern will be
similar to the ones form first pattern. If not selected, both patterns could have different
downcomers. Only available when either Pattern Style 1-2 or 2-3 is selected.
4.3.6.2 Odd Trays Downcomer Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
53
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the
packed bed in the BOM.
Start Elevation. Specifies the start elevation of the packed bed.
Length. Specifies the length of the packed bed.
Diameter. Specifies the outer diameter of the packed bed.
Material. Specifies the material of the packed bed.
Density. Specifies the density for the selected material.
Present when Empty. If selected, insulation will be present when tank is empty.
Present for Hydrotest. If selected, insulation will be present for hydrotest.
Include in Lift Weight. If selected, insulation will be included in lift weight.
Liquid Hold Up Percent. The liquid holdup percent for the packed bed.
Weight Empty. Specifies the packed bed weight when empty.
Weight Operating. Specifies the packet bed weight when operating.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
54
TECHNOSOFT INC.
AMPreVA 5.0
4.4 Support
The type of support to be used for the tank should be appropriately selected from the first tab
under the General menu. The General menu was introduced in the previous section as shown in
Figure 13. Based on the selected type of support from the General menu, the content of the
second row when the Support button is selected may change. It could show lugs and skirt,
saddles, or legs as shown in Figure 43 thru Figure 47.
Figure 43 Support options available when Lugs is selected from the General menu
Figure 44 Support options available when Saddle is selected from the General menu
Figure 45 Support options available when Legs is selected from the General menu
Figure 46 Support options available when Skirt is selected from the General menu
Figure 47 Support options available when Lugs & Legs is selected from the General menu
This section describes the various properties than can be edited from the menus that can also be
invoked from the model tree by editing the appropriate component. Each component may have
various properties but only a subset is provided to be modified by the end user in the menu.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
55
TECHNOSOFT INC.
AMPreVA 5.0
4.4.1 Legs
The component edit form has a number of tabs as illustrates Figure 48. The edit area includes
the following tabs Design, Pad, Base Plate, Grounding Lug, Brace, and Knee Brace. The various
leg types are shown in Figure 49 thru Figure 56.
4.4.1.1 Design Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
56
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
57
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
58
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the legs
in the BOM.
Attach to Component. Component to which the legs are attached to.
Leg Type. There are 7 types of legs supported by the system: Equal Angle (Leg In), Equal
Angle (Leg Out), Wide Flange (Flange In), Wide Flange (Flange Out), T Wide Flange (Flange
In), T Wide Flange (Flange Out), Square Tube, C-Channel, and Pipe.
Pipe Nominal Size. Specifies the nominal size of the leg pipe. Only valid when Leg Type Pipe is
selected.
Special Pipe Outer Diameter. Specifies the non-standard outer diameter of the leg pipe. Only
valid when Leg Type Pipe is selected.
Pipe Schedule. Specifies the schedule of the leg pipe. Only valid when Leg Type Pipe is
selected.
Special Pipe Thickness. Specifies the non-standard thickness of the leg pipe. Only available
when Leg Type Pipe is selected.
I Beam Size. Specifies the beam size. Only valid when Leg Type Wide Flange is selected.
T Beam Size. Specifies the beam size. Only valid when Leg Type T Wide Flange is selected.
Angle Size. Specifies the angle size. Only valid when Leg Type Angle is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
59
TECHNOSOFT INC.
AMPreVA 5.0
Square Tube Size. Specifies the channel size. Only valid when Leg Type Square Tube is
selected.
C-Channel Size. Specifies the channel size. Only valid when Leg Type C-Channel is selected.
Size. Describes the leg size.
Material. Specifies the material of the legs.
Density. Specifies the density of the selected material.
Number of Legs. Specifies the number of legs.
Leg Overall Length. Specifies the total length of the legs.
Top to Girth. Specifies the distance from the top of the legs to girth.
Pattern Start Angle. Specifies the start angle of the legs.
Leg Fillet Weld. Specifies the fillet weld of the legs.
Cut at Center or Out of Shell. Specifies the location of the legs regarding the shell.
Aligned to Shell OD or Aligned to Shell ID. Specifies the alignment of the legs cut. Only
available when Cut at Center.
Cut Angle. If selected it will be possible to specify the cut angle of the legs.
Cover Plate Properties
Cover Plate. If selected, the legs will include a cover plate.
At Shell. If selected, cove plate will be created coming right out the Attach to Component outer
diameter. If not selected, cover plate will start over the leg.
Thickness. Specifies the cover plate thickness of the leg pipe. Only available when Cover Plate
is selected.
Material. Specifies the material of the legs cover plate. Only available when Cover Plate is
selected.
Density. Specifies the density of the selected material.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
60
TECHNOSOFT INC.
AMPreVA 5.0
Material. Specifies the material of the legs pad. Only available when Pad is selected.
Density. Specifies the density for the selected material.
Length (Longitudinal). Specifies the longitudinal length of the legs pads. Only available when
Pad is selected.
Width (Circumferential). Specifies the circumferential width of the legs pads. Only available
when Pad is selected.
Thickness. Specifies the thickness of the legs pads. Only available when Pad is selected.
Corner Radius. Specifies the corner radius of the legs pads. Only available when Pad is
selected.
Offset from Leg. Specifies the legs pads extension out of the leg top edge. Only available when
Pad is selected.
Fillet Weld. Specifies the fillet weld of the legs pads. Only available when Pad is selected.
Segmented. If selected, the legs pads will be segmented. Only available when Pad is selected.
Division Info. Specifies the position and spacing information of each legs pad segment. Only
available when Segmented is selected.
Pad. If selected, the legs will include reinforcing pads.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
61
TECHNOSOFT INC.
AMPreVA 5.0
Radial Base Plate. If selected, the legs base plate will be radial to the tank. If not selected they
will be tangential to the tank. Only available when Leg Type Pipe is selected.
Material. Specifies the material of the legs bolts.
Density. Specifies the density for the selected material.
Length. Specifies the length of the leg base plates.
Width. Specifies the width of the leg base plates.
Thickness. Specifies the thickness of the leg base plates.
Bolt Holes. If selected, the legs base plates will have hole.
Bolt Diameter. The legs base plates bolt diameter. Only available when Bolt Holes is selected.
Bolt Clearance. The bolts hole clearance. Only available when Bolt Holes is selected.
Bolt Circle. If selected it will allow specifying the bolt circle of the hole. Only available when
Bolt Holes is selected.
Bolt Holes Positions from Center. Specifies the list of positions for each legs base plate hole.
Only available when Bolt Holes is selected and Bolt Circle is not selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
62
TECHNOSOFT INC.
AMPreVA 5.0
Thickness. Specifies the thickness of the grounding lugs. Only valid when Grounding Lug is
selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
63
TECHNOSOFT INC.
AMPreVA 5.0
Corner Radius. Specifies the corner radius of the grounding lugs. Only valid when Grounding
Lug and grounding lug Type Lug are selected.
Hole Elevation. Specifies the elevation of the grounding lugs hole. Only valid when Grounding
Lug is selected.
Hole Diameter. Specifies the diameter of the grounding lugs hole. Only valid when Grounding
Lug is selected.
Grounding Hole Type. Specifies the type of the leg grounding hole. Only valid when either Leg
Type Wide Flange or T Wide Flange is selected.
Radius. Specifies the radius of the leg grounding hole. Only valid when grounding hole Type
None is not selected.
Distance from Ground. Specifies the leg grounding hole distance from ground. Only valid when
grounding hole Type None is not selected.
Distance from Web Center. Specifies the leg grounding hole distance web center. Only valid
when grounding hole Type None is not selected.
4.4.1.5 Brace Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
64
TECHNOSOFT INC.
AMPreVA 5.0
Brace Supports. If selected, the legs will include braces. Only available when Leg Type Pipe is
selected.
Type. There are two types of legs brace supports available in the system: Flat Bar and Angle.
Only available when Brace Supports is selected.
Material. Specifies the material of the legs braces.
Density. Specifies the density for the selected material.
Start Elevation. Specifies the start elevation of the legs braces. Only available when Brace
Supports is selected.
Length. Specifies the length of the leg braces. Only available when Brace Supports is selected.
Width. Specifies the width of the leg braces. Only available when Brace Supports is selected
and Type Flat Bar is selected.
Thickness. Specifies the thickness of the leg braces. Only available when Brace Supports is
selected and Type Flat Bar is selected.
Size. The size of the angle plate. Only available when Brace Supports is selected and Type
Angle is selected.
Gusset Type. Specifies the type of gusset for the legs braces. Only available when Brace
Supports is selected.
Material. Specifies the material of the legs braces.
Width. Specifies the width of the gusset for the leg braces.
Length. Specifies the length of the gusset for the leg braces.
Thickness. Specifies the thickness of the gusset for the leg braces.
Brace Weld Length. Specifies the distance of the leg to be weld in the gusset.
Fillet Weld. Specifies the fillet weld for the gussets.
4.4.1.6 Knee Brace Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
65
TECHNOSOFT INC.
AMPreVA 5.0
Knee Braces. If selected, the legs will include knee braces. Only available when either Leg Type
Wide Flange Out or T Wide Flange Out is selected.
Material. Specifies the material of the legs knee braces.
Density. Specifies the density for the selected material.
Nominal Size. Specifies the size of the knee braces. Only available when Knee Braces is
selected.
Length. Specifies the length of the knee braces. Only available when Knee Braces is selected.
Elevation. Specifies the elevation of the knee braces. Only available when Knee Braces is
selected.
Eye Bolt Nominal Size. Specifies the size of the knee braces eye bolt. Only available when Knee
Braces is selected.
Eye Bolt Distance from Edge. Specifies the legs knee braces eye bolt distance from edge. Only
available when Knee Braces is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
66
TECHNOSOFT INC.
AMPreVA 5.0
4.4.2 Skirt
The component edit form has a number of tabs as illustrated Figure 64. The edit area includes
the following tabs Design, Bevel, Base Ring, Insulation, Lining, and Conditions. Various skirt
configurations are shown in Figure 65 thru Figure 70.
4.4.2.1 Design Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
67
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
68
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the skirt
in the BOM.
Attach to Component. Component to which the skirt is attached to.
Attach to Component End. Selects component end to attach the skirt.
End to Attach Datum. Selects the skirt end to the Attach to Component.
Inner Diameter from Component. The inner diameter of skirt Attach to Component.
Outer Diameter from Component. The outer diameter of skirt Attach to Component.
End 1 Inner Diameter. The inner diameter of the skirt at top edge.
End 1 Outer Diameter. The outer diameter of the skirt at top edge.
End 0 Inner Diameter. The inner diameter of the skirt at bottom edge.
End 0 Outer Diameter. The outer diameter of the skirt at bottom edge.
Thickness. Specifies the thickness of the skirt.
Length. Specifies the length of the skirt.
Cone Angle. Shows the angle of the conical skirt.
Number of Sections. Specifies the number of sections of the skirt.
Material. Specifies the material of the skirt.
Copy Parameters. Action button that allows the selection of other skirt to take the dimensions
from.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
69
TECHNOSOFT INC.
AMPreVA 5.0
Base Configuration. There are 4 types of configuration supported by the system for skirt base
rings: Single Base Plate, External Chairs, Double Base Plate, and Centered Bolt Chair. Types
External Chair and Centered Bolt Chair are only available when Gussets is selected.
Identifier. It is the label that is shown in the model tree as well as in the description for the head
in the BOM.
Material. Specifies the material of the skirt base ring.
Density. Specifies the density for the selected material.
Base Ring Properties
Inner Diameter. The inner diameter of the base ring.
Outer Diameter. The outer diameter of the base ring.
Thickness. Specifies the thickness of the skirt base ring.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
70
TECHNOSOFT INC.
AMPreVA 5.0
Segmented Base Ring. If selected, the skirt base ring will be segmented. If not selected, the skirt
base ring will be one single piece.
Number of Segments. Specifies the number of segments of the skirt base ring. Only available
when Segmented Base Ring is selected.
Segment Angle Length. Indicates the segments angle length for skirt base ring.
Compression Ring Properties
Match Base Ring OD. If selected the compression ring width will be adjusted to match the base
ring outer diameter.
Width. Specifies the width of the skirt top ring. Only available when either Base Configuration
External Chairs or Double Base Plate is selected, and Match Base Ring OD is not selected.
Thickness. Specifies the thickness of the skirt top ring.
Segmented Compression Ring. If selected, the skirt top ring will be segmented. If not selected,
it will be one single piece. Only available when Base Configuration Double Base Plate is
selected.
Number of Segments. Specifies the number of segments of the skirt top ring. Only available
when Segmented Compression Ring is selected.
Segment Angle Length. Indicates the segments angle length for skirt top ring.
Bolt Properties
Quantity. Specifies the number of bolts of the skirt.
Orientation Angle. Specifies the pattern start angle for the bolts on the skirt base ring.
Type. Specifies the skirt bolts type.
Diameter. Specifies the diameter of the skirt bolts.
Bolt Circle. Specifies the bolt circle of the skirt.
Clearance Base Ring. Specifies the bolts root opening of the skirt at base ring.
Clearance Compression Ring. Specifies the bolts root opening of the skirt at top ring.
Material. Specifies the material of the skirt bolts.
Gusset Properties
Type. Specifies the type of gussets for the skirt base ring.
Material. Specifies the material of the gussets. Only available when Gussets is selected.
Height. Specifies the height of the gussets. Only available when Gussets is selected.
Separation. Specifies the spacing between skirt gussets. Availability depends on the gusset
type.
Thickness. Specifies the thickness of the gussets. Only available when Gussets is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
71
TECHNOSOFT INC.
AMPreVA 5.0
Chamfer Length. Specifies the chamfer length of the gussets. Only available when Gussets is
selected.
Offset from Rings. Specifies the gussets distance from skirt base ring outer diameter. Only
available when Gussets is selected.
4.4.2.4 Conditions Tab
See Conditions Common Tab specifications as in Figure 21.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
72
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
73
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the lugs
in the BOM.
Attach to Component. Component to which the lugs are attached to.
Material. Specifies the material of the lugs.
Number of Lugs. Specifies the number of lugs.
Start Elevation. Specifies the elevation of the lugs support from Attach to Component.
Orientation Angle. Specifies the orientation angle of the lugs support.
Invert Direction. If selected, the lugs supports will be created upside-down.
Plates. If selected, the support lugs will include either base and compression rings, or base and
compression plates.
Compression Plate. If selected, the lugs support will have a top ring.
Continuous Top and Base Rings. If selected, lugs will have continuous top and base rings. If is
not selected, lugs will have plates under each pair of gusset.
Segmented Base Ring. If selected, the lugs base ring will be segmented. If not selected, the skirt
base ring will be one single piece.
Segmented Base Rings and Plates. If selected and Continuous Top and Base Rings is also
selected, the lugs base ring will be made of segments and plates under the gussets.
Design Factor. Specifies the design factor of the lugs support.
Distance to Load. Specifies the distance to load of the lugs support.
Weld Size. Specifies the weld size of the lugs support.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
74
TECHNOSOFT INC.
AMPreVA 5.0
Weld Size Pad. Specifies the weld size of the lugs support pad. Only applicable when Pad is
selected.
Base Moment. Specifies the base moment of the support lugs.
Base Shear. Specifies the base shear of the support lugs.
Weight. Specifies the weight of the lugs support.
4.4.3.2 Top and Base Ring Tab
Compression Plate. If selected, the lugs support will have a top ring.
Continuous Top and Base Rings. If selected, lugs will have continuous top and base rings. If is
not selected, lugs will have plates under each pair of gusset.
Segmented Base Ring. If selected, the lugs base ring will be segmented. If not selected, the skirt
base ring will be one single piece.
Segmented Base Rings and Plates. If selected and Continuous Top and Base Rings is selected,
the lugs base ring will be made of segments and plates under the gussets. Only available when
Segmented Base Ring is selected.
Number of Base Ring Segments. Specifies the number of segments for lugs base ring. Only
available when Segmented Base Ring is selected and Segmented Base Rings and Plates is not
selected.
Base Ring Thickness. Specifies the thickness of the lugs base ring. Only available when
Segmented Base Ring is selected.
Base Ring Width. Specifies the width of the lugs base ring.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
75
TECHNOSOFT INC.
AMPreVA 5.0
Number of Top Ring Segments. Specifies the number of segments for lugs top ring. Only
available when Segmented Top Ring is selected.
Top Ring Segment Angle Length. Shows the angle of the ring segments. Only available when
Segmented Top Ring is selected.
4.4.3.3 Top and Base Plate Tab
Compression Plate. If selected, the lugs support will have a top ring.
Continuous Top and Base Rings. If selected, lugs will have continuous top and base rings. If is
not selected, lugs will have plates under each pair of gusset.
Base Plate Circumferential Width. Specifies the width of the lugs base plate.
Base Plate Radial Length. Shows the distance from the shell outer diameter to the base plate
outer edge.
Base Plate Thickness. Specifies the thickness of the lugs base plates.
Top Plate Thickness. Specifies the thickness of the lugs top plates.
Top Plate Width. Specifies the width of the lugs top plates.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
76
TECHNOSOFT INC.
AMPreVA 5.0
Pate Type. Drop down menu with the following options: None, Pad, and Belly Band. If None is
selected, the support lugs wont have reinforcing pad; if Pad is selected, each support lug will
have its own pad; if Belly Band is selected, a rolled plate will be used as a common pad for all
the support lugs. Only available when Continuous Top and Base Rings is not selected.
Longitudinal Length. Specifies the longitudinal length of the lugs pad. Only available when Pad
is selected.
Circumferential Length. Specifies the circumferential length of the lugs pad. Only available
when Pad is selected. Only available when Plate Type Pad is selected.
Thickness. Specifies the thickness of the lugs pad. Only available when Pad is selected.
4.4.3.5 Gusset Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
77
TECHNOSOFT INC.
AMPreVA 5.0
Grounding Lug in Gusset 1. If selected, lugs gusset 1 will have a grounding lug.
Grounding Lug in Gusset 2. If selected, lugs gusset 2 will have a grounding lug.
Type. There are 2 types of grounding lugs supported by the system: Lug and Angle. Only
available when either Grounding Lug in Gusset 1 or Grounding Lug in Gusset 2 is selected.
Orientation. Specifies the orientation of the lug plates in the gussets. Only available when either
Grounding Lug in Gusset 1 or Grounding Lug in Gusset 2 is selected.
Elevation. Specifies the elevation of the lug plates from gusset bottom edge. Only available
when either Grounding Lug in Gusset 1 or Grounding Lug in Gusset 2 is selected.
Distance from Edge. Specifies the lug plate distance from gusset inner edge. Only available
when either Grounding Lug in Gusset 1 or Grounding Lug in Gusset 2 is selected.
Width. Specifies the width of the grounding lugs. Only available when either Grounding Lug in
Gusset 1 or Grounding Lug in Gusset 2 is selected.
Height. Specifies the height of the grounding lugs. Only available when either Grounding Lug
in Gusset 1 or Grounding Lug in Gusset 2 is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
78
TECHNOSOFT INC.
AMPreVA 5.0
Depth. Specifies the depth of the grounding lugs. Only available when either Grounding Lug in
Gusset 1 or Grounding Lug in Gusset 2 is selected.
Thickness. Specifies the thickness of the grounding lugs. Only available when either Grounding
Lug in Gusset 1 or Grounding Lug in Gusset 2 is selected.
Corner Radius. Specifies the corner radius of the grounding lugs.
grounding lug Type Lug is selected.
Hole Elevation. Specifies the elevation of the grounding lugs hole. Only available when either
Grounding Lug in Gusset 1 or Grounding Lug in Gusset 2 is selected.
Hole Diameter. The hole diameter of the grounding lugs. Only available when either
Grounding Lug in Gusset 1 or Grounding Lug in Gusset 2 is selected.
4.4.3.7 Bolt Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
79
TECHNOSOFT INC.
AMPreVA 5.0
4.4.4 Saddle
The component edit form has a number of tabs as illustrates Figure 90. The edit area includes
the following tabs Design, Saddles, Additional Floor, Grounding Lug, and Conditions. Various
saddles configurations are shown in Figure 83 thru Figure 89.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
80
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
81
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
82
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the
saddles in the BOM.
Type. There are 3 types of saddles supported by the system.
Material. Specifies the material of the saddle.
Density. Specifies the density for the selected material.
Elevation List. Specifies the elevation for each saddle.
Height List. Specifies the height of each saddle.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
83
TECHNOSOFT INC.
AMPreVA 5.0
Contact Angle Based on. Allows to determinate the contact angle measurement points, whether
Inside Rib Edge or Outside Rib Edge.
Contact Angle List. Specifies the contact angle of the saddles.
Base Plate Properties
Type. There are three types of base plate supported by the system: None, Single, Double. When
None is selected, there wont be any base plate; when Single is selected, one plate per saddle will
be used as base plate; when Double is selected, the base plate will be split in two sections per
saddle. Availability depends on saddle type.
Length. Specifies the length of the saddles base plate.
Width. Specifies the width of the saddles base plate.
Thickness. Specifies the thickness of the saddles base plate.
Extends. Specifies the saddles base plate extension out of the saddle lateral ribs.
Rib Properties
Lateral Ribs. If selected, saddle will include lateral ribs. Only available when Saddle Type 1 is
selected.
Thickness. Specifies the thickness of the saddles rib plates.
Rib Quantity List. Specifies the number of rib plates per the saddle.
Lateral Ribs Width List. Specifies the width of the rib plates of each saddle.
Intermediate Ribs Style List. Specifies the ribs style per saddle. The options are: DS (double
side), NS (negative side), and PS (positive side). Available only for saddle type 1.
Intermediate Ribs Spacing List. Specifies the spacing between the rib plates of each saddle.
Set Equal Intermediate Ribs Spacing. Action button to equal the spacing between the saddles
intermediate ribs.
Web Type. There are three types supported by the system. Availability depends on the saddle
type.
Material. Specifies the material of the saddles web plate.
Density. Specifies the density for the selected material.
Web Plate Offset List. Specifies a distance to locate the web plate from the center of each saddle.
Only available when Saddle Type 1 is selected.
Thickness. Specifies the thickness of the saddles web plate.
Wear Plate. If selected, the saddles will include a wear plate. If not selected, the saddles will
not include a wear plate.
Material. Specifies the material of the saddle wear plate. Only available when Wear Plate is
selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
84
TECHNOSOFT INC.
AMPreVA 5.0
Density. Specifies the density for the selected material. Only available when Wear Plate is
selected.
Width. Specifies the width of the saddles wear plate. Only available when Wear Plate is
selected.
Thickness. Specifies the thickness of the saddles wear plate. Only available when Wear Plate is
selected.
Contact Angle. Specifies the contact angle of the saddles wear plate. Only available when Wear
Plate is selected.
Corner Radius. Specifies the corner radius of the saddles wear plate. Only available when Wear
Plate is selected.
NPT Hole. If selected, the wear plate will have a NPT hole. Only available when Wear Plate is
selected.
Diameter. Specifies the diameter of the wear plate NPT hole. Only available when Wear Plate
and NPT Hole are selected.
Offset from Edge. Specifies the distance of the NPT hole from the edge of the wear plate. Only
available when Wear Plate is selected.
Offset from Center. Specifies the distance of the NPT hole from the center of the wear plate.
Only available when Wear Plate is selected.
Bolts Properties
Type. Specifies the type of bolt to use.
Quantity. Specifies the number of bolts for each saddle.
Diameter. The diameter of the saddle bolts.
Hole Root Length. Specifies the root opening of the saddle bolts hole.
Hole Slotted Length. Specifies the slotted length of the saddle bolts hole.
X-Y Position List. Specifies the (X, Y) bolt holes positions from base plate center. Only
available when bolts Quantity greater than zero.
Slotted Holes. The saddle selected will have slotted bolt holes. The not selected will have
circular bolt holes.
Material. Specifies the material of the saddle bolts.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
85
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
86
TECHNOSOFT INC.
AMPreVA 5.0
Elevation. Specifies the elevation of the saddles grounding lug. Only available when Same
Configuration is selected.
Spacing Between Lugs. Specifies the spacing between saddles grounding lugs. Only available
when Same Configuration is selected.
Configuration Info. Allows specifying the position for each grounding lug separately. Only
available when Same Configuration is not selected.
At Front Side. If selected, the grounding lugs will located at saddle front side. If not selected,
they will be located in the saddle back side. Only available when either both At Web and Same
Configuration are selected, or both are not selected.
At Web. If selected, the grounding lugs will located in the saddle web plate. If not selected, they
will be located in the lateral plates.
Same Configuration. If selected, all the grounding lugs in the same saddle will have the same
Elevation. Only available when At Web is selected.
Holes Properties
Radius. Specifies the radius of the saddles grounding lug hole.
Elevation. Specifies the elevation of the saddles grounding lug hole.
4.4.4.4 Foundation Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
87
TECHNOSOFT INC.
AMPreVA 5.0
Size. Specifies the size of the saddles tube. Only available when Saddle Type 2 is selected.
Vertical Tubes Spacing. Specifies the spacing between vertical tubes. Only available when
Saddle Type 2 is selected.
Horizontal Tube Elevation. Specifies the elevation for the horizontal tube. Only available when
Saddle Type 2 is selected.
4.4.4.6 Conditions Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
88
TECHNOSOFT INC.
AMPreVA 5.0
4.5 Nozzle
When selecting the +Nozzle from the toolbar, as shown in Figure 96, a component must be
selected from the canvas to attach the nozzle to.
4.5.1 +Nozzle
The component edit form has a number of tabs as illustrated Figure 97. The edit area includes
the following tabs Design, Pad, Bevel, Connections, Flange, Flange Inside, Closure, Closure
Inside, Weld, Steiner Clips, and Conditions.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
89
TECHNOSOFT INC.
AMPreVA 5.0
Drawing Mark. It is the label that is shown in the model tree as well as in the description for the
nozzle in the BOM and the drawings.
Service. Specifies the service of the nozzle.
Remarks. Specifies some comments about the nozzle.
Material. Specifies the material of the nozzle.
Pipe. If selected, the nozzle pipe will be considered a seamless pipe. If not selected, the pipe
will be considered as a rolled plate.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
90
TECHNOSOFT INC.
AMPreVA 5.0
Manway. If selected, the nozzle will be considered as manway. If not selected, it will be
considered as nozzle.
Attachment Type. There are 2 types of attachment types for the nozzles supported by the system:
Stick Thru and Set On.
Fitting Type. There are 6 types of fittings supported by the system: Nozzle, Studding Outlet,
Half Coupling, Full Coupling, Half Socket Welded, and Full Socket Welded.
NPS. The diameter nominal size of the nozzle. If custom is selected, user will type in OD or ID.
Sch. The schedule of the nozzle. If custom is selected the user will type in thickness.
Outer Diameter. The outer diameter of the nozzle pipe.
Inner Diameter. The inner diameter of the nozzle pipe.
Thickness. The thickness of the nozzle pipe.
Orientation. For nozzles in head, there are 3 types of orientation: Radial, Perpendicular and
Hillside. For nozzles in Shell, Cone, and Skirt, there are 2 types of orientation: Radial, and
Offset.
Orientation Angle. Specifies the angle position of the nozzles.
Start Elevation. Specifies the start elevation of the nozzle. Only available for nozzles in the
Shell, Transition, or skirts.
Radial Distance. Specifies the distance from the center of the head to the center of the nozzle.
Only available for nozzles in the Head.
Offset. Specifies the nozzle offset from cylinder center line. Only available when Orientation
Offset is selected.
Tipping Angle Horizontal. Specifies a horizontal inclination angle for the nozzle. Only available
for nozzles in Shell.
Tipping Angle Vertical. Specifies a vertical inclination angle for the nozzle. Only available for
nozzles in Shell.
Projection Distance Mode. There are two ways to specify the nozzle projection:
Projection and Outside Projection. Only available for nozzles in Shell.
Radial
Radial Projection Distance. Specifies the nozzle radial distance from tank center.
available when Projection Distance Mode Radial Projection is selected.
Only
Outside Projection Distance. Specifies the nozzle outside length from Attach to Component
outer diameter. Only available when Projection Distance Mode Outside Projection is selected.
Inside Projection Distance. Specifies the nozzle inside length from Attach to Component inner
diameter.
Length from Head Tangent Line. Specifies the distance from the tangent line of the head to the
raised face of the nozzle. Only available for nozzles in Head.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
91
TECHNOSOFT INC.
AMPreVA 5.0
Pad. If selected, the nozzle will include a reinforcing pad. Only available when Fitting Type
Studding Outlet is not selected.
Material. Specifies the material of the nozzle pad. Only available when Pad is selected.
Density. Specifies the density for the selected material.
Thickness. Specifies the thickness of the nozzle pad. Only available when Pad is selected.
Width. Specifies the width of the nozzle pad. Only available when Pad is selected.
Root Opening. Specifies the root opening of the nozzle pad. Only available when Pad is
selected.
Fine Grain. If selected, specifies a pad material fine grain. Only available when Pad is selected.
Impact Tested. If selected, the pad will be impact tested. Only available when Pad is selected.
Normalized. If selected, the pad will be normalized. Only available when Pad is selected.
NPT Hole Properties
Diameter. Specifies the diameter of the nozzles NPT hole.
4.5.1.3 Bevel Tab
See Bevel Common Tab as described in Figure 17.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
92
TECHNOSOFT INC.
AMPreVA 5.0
Outside Connection Type. There are 3 types of outside connectors supported by the system:
Elbow, Nozzle Inside, and Reducer.
Inside Connection Type. There are 6 types of inside connectors supported by the system:
Elbow, Vortex Breaker Type 1, Vortex Breaker Type 2, Vortex Breaker Type 3, Vortex Breaker
Type 4, and Vortex Breaker Type 5. All vortex breakers are alpha release features.
Gusset Type. There are 4 gusset types supported by the system: Plate at Pipe, Plate at Flange,
Flat Bar at Pipe, and Flat Bar at Extension.
Chordal Baffle. If selected, the nozzle will include an internal chordal baffle.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
93
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
94
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
95
TECHNOSOFT INC.
AMPreVA 5.0
Type. There are two cover types supported by the system: Blind and Gauge Hatch. The last
type is only available for flanges not greater than size 10. The Gauge Hatch option is an alpha
release feature.
Blind Weight. Specifies the weight of the flange blind. Only available when Cover Type None is
not selected.
4.5.1.6 Inside Flange Tab
See Nozzle Outside Flange Tab.
4.5.1.7 Outside Closure Tab
Closure. If selected, the nozzle will include an outer cap. Only available when Flange is not
selected.
Identifier. It is the label that is shown in the model tree as well as in the description for the
flange in the BOM.
Material. Specifies material of the pipe cap.
Density. Specifies the density for the selected material.
Outer Diameter. Specifies the outer diameter of the pipe cap.
Inner Diameter. Specifies the inner diameter of the pipe cap.
Straight Section Thickness. Specifies the straight flange thickness of the pipe cap.
available for Head Type Ellipsoidal, F&D, Hemi, and Torispherical.
Only
Straight Section Length. The straight flange length of the pipe cap. Only available for Head
Type Ellipsoidal, F&D, Hemi, and Torispherical.
4.5.1.8 Inside Closure
See Nozzle Outside Closure Tab.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
96
TECHNOSOFT INC.
AMPreVA 5.0
Angle Clockwise Direction. If selected, steiner clip orientation will be applied following the
hands of a clock rotate. If not selected, steiner clip orientation will be applied counterclockwise.
Quantity. The number of steiner clips in the nozzle.
Type. There are 2 types of steiner clips supported by the system: Plate and Angle.
Orientation Angle List. Specifies the angle position for each steiner clip. Only available when
Quantity is greater than zero.
Offset from Nozzle Top Edge. Specifies the steiner clip offset from nozzle top edge.
Steiner Properties
Thickness. Specifies the thickness of the steiner clip.
Height. Specifies the height of the steiner clip.
Width. Specifies the width of the steiner clip.
Holes Properties
Diameter. The steiner clips hole diameter.
Offset from Inner Edge. The offset from steiner clip inner edge to hole center line.
Offset from Top Edge. The offset from steiner clip top edge to hole center line.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
97
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
98
TECHNOSOFT INC.
AMPreVA 5.0
Edge Preparation
Chamfer Angle. Specifies the angle for the chamfer.
Chamfer Land Length. Specifies the land length for the chamfer.
Flange Weld
Type. Specifies the type of attachment for the flange.
Upper Fillet. Specifies the upper fillet size.
Lower Fillet. Specifies the lower fillet size.
4.5.1.11 Conditions Tab
See Conditions Common Tab specifications as in Figure 21.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
99
TECHNOSOFT INC.
AMPreVA 5.0
4.6 Rings
When the Rings button is selected the second row will show the various rings options that can
be added. Once a button is selected from the second row, the system will expect the user to
select a component from the canvas area for attaching the ring. The tabs in the work area
provide the user the various options for setting the ring features and properties. The various ring
types are shown in Figure 105 thru Figure 111.
+Ring 1. Various styles can be selected including Flat Bar, Angle, I-beam, T-beam, C-beam,
and Y-beam. Options are provided to allow the specification of the attachment at the outside or
the inside of the component. Ring 1 can be attached to a cylinder, a head, a transition, or a skirt.
Not all shapes may be available for attaching on the different components.
+Insulation 1. Available only for heads. This is commonly used for insulation support.
+Insulation 2. Available only for heads. This can be used for insulation support or structural
stiffener.
+Insulation 3. Available only for heads. This is commonly used for insulation support.
+Insulation 4. Available for cylinders, skirts, and heads. This is commonly used for insulation
support.
+Insulation 5. Available only for heads. This is commonly used for insulation support.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
100
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
101
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
102
TECHNOSOFT INC.
AMPreVA 5.0
4.7 Appurtenances
When the appurtenances button is selected the second row of the toolbar will update to show the
various components available for adding. Once a button is selected from the second row, a
component should be selected from the canvas to attach to. The tabs in the work area are
updated to provide setting the features and properties of component being added.
Some of these components are in test version. They will be updated and enhanced in future
releases. The GUI details will be updated in future releases. The attachment of these
components is shown in Figure 113 thru Figure 120.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
103
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
104
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
105
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the lift
lug in the BOM.
Attach to Component. Component to which the lift lug is attached to.
Lug Type. There are five types of lift lug: Tail, Ear Simple, Ear, Fixed Trunnion, and Trunnion
Trunnion. The availability of the types depends on the component it is attached to.
Elevation from. Specifies the side of the component to be attached.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
106
TECHNOSOFT INC.
AMPreVA 5.0
Offset. The distance of the lift lug edge till the selected side on Elevation from.
Position Angle. Specifies the angle position of the lift lug.
Lug Properties
Material. Specifies the material of the lift lug.
Density. Specifies the density for the selected material.
Length. Specifies the length of the lug from the weld till the center of the hole. Availability
depends on the lift lug type selected.
Straight Height. Specifies the length of the straight section without the weld. Availability
depends on the lift lug type selected.
Weld Length. Specifies the length of the lug to be welded. Availability depends on the lift lug
type selected.
Width. Specifies the width of the lug. Availability depends on the lift lug type selected.
Thickness. Specifies the thickness of the thickness.
Weld Size. Specifies the size of the weld.
Lower Corner Radius. Specifies the radius of the lug lower corner. Availability depends on the
lift lug type selected.
Upper Corner Radius. Specifies the radius of the lug upper corner. Availability depends on the
lift lug type selected.
View Lifting Lug Types. Action button to display the different lift lug types.
Copy Parameters. Action button that allows the selection of other lift lug to take the dimensions
from.
Hole Properties
Diameter. Specifies the diameter of the lift lug hole. Availability depends on the lift lug type
selected.
Height from Base. Specifies the distance from the lug base till the center of the hole.
Availability depends on the lift lug type selected.
Offset from Center Line. Specifies the distance from the center of the lug till the center of the
hole. Availability depends on the lift lug type selected.
NPT Hole Properties
NPT Hole. If selected, the lift lug will have a NPT hole. Availability depends on the lift lug
type selected.
Diameter. Specifies the diameter of the lift lug NPT hole. Only available when NPT Hole is
selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
107
TECHNOSOFT INC.
AMPreVA 5.0
Offset from Bottom Lug. Specifies the distance of the NPT hole from the bottom of the lift lug.
Only available when NPT Hole is selected.
Offset from Center Lug. Specifies the distance of the NPT hole from the center of the lift lug.
Only available when NPT Hole is selected.
4.7.1.2 Pad Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
108
TECHNOSOFT INC.
AMPreVA 5.0
Offset from Center Pad. Specifies the distance of the NPT hole from the bottom of the
reinforcing pad. Only available when Pad is selected and NPT Hole are selected.
4.7.2 + Clip Type 1
4.7.2.1 Design Tab
Identifier. It is the label that is shown in the model tree as well as in the description for the clip
type 1 in the BOM.
Angle Clockwise Direction. If selected, clip type 1 orientation will be applied following the
hands of a clock rotate. If not selected, clip type 1orientation will be applied counterclockwise.
Position Angle. Specifies the angle position of the clip type 1.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
109
TECHNOSOFT INC.
AMPreVA 5.0
Radial Distance. Specifies the distance from the center of the head to the center of the clip type
1. Only available when clip is attached to the Head.
Start Elevation. Specifies the start elevation of the clip type 1. Only available when clip is not
attached to the Head.
Direction. It can be defined whether as Parallel to Axis or Ortho to Axis.
Material. Specifies the material of the clip type 1.
Density. Specifies the density of the selected material.
Style. It can be defined whether as Single or Double.
Spacing. Specifies the distance between clips of type 1 when Style is Double.
Direction Normal to Head. If selected, the clip type 1 will be pointing perpendicularly to the
head; if not selected, the clip type 1 will follow the curvature of the head.
Start Elevation in Straight Flange. Takes the elevation of the clip type 1 in reference of the edge
of the head at the straight flange. Only available when attached to a head, and Radial Distance is
equal to half of the heads outer diameter.
Thickness. Specifies the thickness of the clip type 1.
Height to Center Hole. Specifies the height of the clip type 1 from the bottom edge till the center
of the hole.
Nose Radius. Specifies the radius of the nose for the clip type 1.
Left Width. Specifies the width on the left side for the clip type 1.
Right Width. Specifies the width of the right side for the clip type 1.
Left Chamfer. Specifies the length of the chamfer on its left side for the clip type 1.
Right Chamfer. Specifies the length of the chamfer on its right side for the clip type 1.
Weld Size. Specifies the size of the weld for the clip type 1.
Left Chamfer Cut. If selected, the clip type 1 could have a cut in its left side.
Left Angle. Specifies the chamfer angle to be cut in its left side. Only available when Left
Chamfer Cut is selected.
Right Chamfer Cut. If selected, the clip type 1 could have a cut in its right side.
Right Angle. Specifies the chamfer angle to be cut in its right side. Only available when Right
Chamfer Cut is selected.
Round Edge. If selected the nose of the clip type 1 will be round; if not selected, the nose of the
clip type will be straight.
Upper Width. Specifies the length of the straight nose for the clip type 1. Only available when
Round Edge is not selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
110
TECHNOSOFT INC.
AMPreVA 5.0
Copy Parameters. Action button that allows the selection of other clip of type 1 to take the
dimensions from.
Holes Properties
Type. Specifies the type of hole for the clip type 1. Options are: None, Circular, and Slotted.
Quantity. Specifies the number of holes in the clip type 1; options are 1 and two. Only available
when Type is not None.
Spacing. Specifies the distance between the holes, from outer diameter to outer diameter. Only
available when Type is not None and Quantity is 2.
Arrangement Orientation. Specifies the way to locate the clip type 1 holes; the options are
Vertical and Horizontal. Only available when Type is not None and Quantity is 2, or when Type
is Slotted.
Radius. Specifies the radius of the hole. Only available when Type is not None.
Slotted Length. Specifies the slotted length of the hole. Only available when Type is Slotted.
4.7.2.2 Pad and Support Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
111
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
112
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the clip
type 2 in the BOM.
Angle Clockwise Direction. If selected, clip type 2 orientation will be applied following the
hands of a clock rotate. If not selected, clip type 1orientation will be applied counterclockwise.
Position Angle. Specifies the angle position of the clip type 2.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
113
TECHNOSOFT INC.
AMPreVA 5.0
Radial Distance. Specifies the distance from the center of the head to the center of the clip type
2. Only available when clip is attached to the Head.
Start Elevation. Specifies the start elevation of the clip type 2. Only available when clip is not
attached to the Head.
Direction. It can be defined whether as Parallel to Axis or Ortho to Axis.
Shape. There are three shapes available for the clip type 2.
Material. Specifies the material for the clip type 2.
Density. Specifies the density for the selected material.
Style. Specifies the style of the clip type 2, whether Single or Double.
Spacing. Specifies the spacing between lugs. Only available when Style Double is selected.
Direction Normal to Head. If selected, the clip type 2 will be pointing perpendicularly to the
head; if not selected, the clip type 2 will follow the curvature of the head.
Start Elevation in Straight Flange. Takes the elevation of the clip type 2 in reference of the edge
of the head at the straight flange. Only available when attached to a head, and Radial Distance is
equal to half of the heads outer diameter.
Radial Left Top. Specifies the length of the clip type 2 at the upper left side.
Left Down. Specifies the length of the clip type 2 at the lower left side.
Width Down. Specifies the width of the clip type 2 at lower edge.
Width Top. Specifies the width of the clip type 2 at upper edge.
Right Top. Specifies the length of the clip type 2 at the upper right side.
Right Down. Specifies the length of the clip type 2 at the lower right side.
Thickness. Specifies the thickness of the clip type 2.
Weld Size. Specifies the weld size of the clip type 2.
Copy Parameters. Action button that allows the selection of other clip of type 2 to take the
dimensions from.
Holes Properties
Type. Specifies the type of hole, either None or Circular or Slotted.
Horizontal Displacement. Specifies the distance from the center of the hole to the center of the
clip type 2. Only available when Type is not None.
Vertical Displacement. Specifies the distance from the center of the hole to the bottom edge of
the clip type 2. Only available when Type is not None.
Info. Specifies the required information to locate the holes in the clip type 2. Only available
when Type is not None.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
114
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
115
TECHNOSOFT INC.
AMPreVA 5.0
Diameter. Specifies the diameter of the NPT hole of the reinforcing pad. Only available when
NPT Hole is selected.
Support Plates Properties
Support Plate. There are 6 types of Support Plate supported for the clip type 2: None, Left,
Right, Double, Double Left, and Double Right.
Material. Specifies the material of the support plate. Only available when Support Plate is not
None.
Density. Specifies the density for the selected material. Only available when Support Plate is
not None.
Offset. Specifies the distance the support plate will be located out of the center of the clip type 2.
Thickness. Specifies the thickness of the support plate. Only available when Support Plate is
not None.
Length. Specifies the length of the support plate. Only available when Support Plate is not
None.
Up Width. Specifies the width of the support plate in the upper part of the plate. Only available
when Support Plate is not None.
Width. Specifies the width of the support plate in the lower part of the plate. Only available
when Support Plate is not None.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
116
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the
vibrator mount in the BOM.
Material. Specifies the material of the vibrator mount.
Density. Specifies the density of the selected material.
Position Angle. Specifies the angle position of the vibrator mount.
Radial Distance. Specifies the distance from the center of the head to the center of the vibrator
mount. Available only when it is attached to a Head.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
117
TECHNOSOFT INC.
AMPreVA 5.0
Start Elevation. Specifies the start elevation of the vibrator mount. Available only when it is not
attached to a Head.
Rotation Type. Specifies the way to orient the c-channel beam. There are three styles. Available
only when it is attached to a Head.
Position Type. Specifies the way to attach the c-channel beam. There are four styles.
Description. Specifies the size of the c-channel beam.
Radius Arc. Specifies the radius arc of the c-channel beam.
Thickness. Specifies the thickness of the c-channel beam.
Length. Specifies the length of the c-channel beam.
Location. Specifies the location of the t-beam, it could be either internal or external. Only
available when it is not attached to a Head.
Copy Parameters. Action button that allows the selection of other vibrator mount of type cchannel to take the dimensions from.
Hole Properties
Type. Specifies the type of hole, there are three options: None, Circular and Slotted.
Diameter. Specifies the diameter of the c-channel beam. Available only when Type None is not
selected.
Slotted Length. Specifies the length of the slotted hole. Available only when Type Slotted is
selected.
Elevation List. Specifies the elevation for each hole in the beam. Available only when Type
None is not selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
118
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the
vibrator mount in the BOM.
Material. Specifies the material of the vibrator mount.
Density. Specifies the density of the vibrator mount.
Position Angle. Specifies the angle position of the vibrator mount.
Start Elevation. Specifies the start elevation of the vibrator mount. Available only when it is not
attached to a Head.
Position Type. Specifies the way to attach the t-beam. There are four styles.
Description. Specifies the size of the t-beam.
Location. Specifies the location of the t-beam, it could be either internal or external.
Length. Specifies the length of the t-beam.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
119
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the shell
rung in the BOM.
Material. Specifies the material of the shell rung.
Density. Specifies the density of the selected material.
Quantity. Specifies the number of shell rungs for the group.
Rung to Rung Distance. Specifies the spacing in distance between rungs, from center to center.
Only available when Group Orientation is Longitudinal.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
120
TECHNOSOFT INC.
AMPreVA 5.0
Rung to Rung Distance (Angle). Specifies the spacing in angle between rings, from center to
center. Only available when Group Orientation is Circumferential.
Elevation from. Specifies the side of the component to start counting the elevation.
Offset. Specifies the distance from the edge selected in Elevation from till the center of the first
rung in the group.
Position Angle. Specifies the angle location of the group of shell rungs.
Location. Specifies the location of the group of shell rungs, it could be either internal or
external.
Type. There are two type of shell rungs supported: Type I, and Type II.
Group Orientation. There are two orientation supported for the shell rungs: Longitudinal, and
Circumferential.
Angle Clockwise Direction. If selected, shell rungs group orientation will be applied following
the hands of a clock rotate. If not selected, shell rungs group orientation will be applied
counterclockwise.
Copy Parameters.
dimensions from.
Action button that allows the selection of other shell rung to take the
Rung Properties
Width. Specifies the width of the shell rung.
Height. Specifies the height of the shell rung.
Depth. Specifies the depth of the shell rung. Only available when Type II.
Diameter. Specifies the diameter of the shell rung.
Corner Radius. Specifies the corner radius of the shell rung.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
121
TECHNOSOFT INC.
AMPreVA 5.0
Radial,
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
122
TECHNOSOFT INC.
AMPreVA 5.0
Action button that allows the selection of other head rung to take the
Description. It is the label that is shown in the model tree as well as in the description for the
baffle in the BOM.
Orientation Angle. Specifies the angle position of the baffle.
Baffle properties
Type. There are 2 types of triangular baffles supported by the system: Triangular and Simple.
Start Distance from Top. Specifies the baffle start distance from cylinder top edge.
Start Distance from Bottom. Specifies the baffle start distance from cylinder bottom edge.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
123
TECHNOSOFT INC.
AMPreVA 5.0
Width. Specifies the width of the baffle. Only available when Baffle Type Triangular is
selected.
Thickness. Specifies the thickness of the baffle.
Distance from Shell. Specifies the baffle distance from shell inner diameter. Only available
when Baffle Type Simple is selected.
Distance from Support Plate. Specifies the baffle distance from support plate. Only available
when Baffle Type Simple is selected.
Material. Specifies the material of the baffle.
Triangular Plates Properties
Thickness. Specifies the thickness of the baffle triangular plates. Only available when Baffle
Type Triangular is selected.
Material. Specifies the material of the baffle triangular plates. Only available when Baffle Type
Triangular is selected.
Support Plates Properties
Supports. When selected the baffle is supported to plates; when its not selected, the baffle is
directly attached to the shell. Only available when Baffle Type Simple is selected.
Quantity. Specifies the number of baffle support plates.
Length. Specifies the length of the baffle support plates.
Thickness. Specifies the thickness of the support plates.
External Width. Specifies the external width of the baffle support plates.
Internal Width. Specifies the internal width of the baffle support plates.
Material. Specifies the material of the baffle support plates.
Top and Bottom Dist from Baffle. Specifies the distance from baffle to top and bottom.
Internal Plates Properties
Quantity. Specifies the number of baffle internal plates. Only available when Baffle Type
Triangular is selected.
Width. Specifies the width of the baffle internal plates. Only available when Baffle Type
Triangular is selected.
Height. Specifies the height of the baffle internal plates. Only available when Baffle Type
Triangular is selected.
Thickness. Specifies the thickness of the baffle internal plates. Only available when Baffle Type
Triangular is selected.
Material. Specifies the material of the baffle internal plates. Only available when Baffle Type
Triangular is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
124
TECHNOSOFT INC.
AMPreVA 5.0
Type. There are 2 types of steel baffles supported by the system: Tube Simple and Tube
Triangular.
Description. It is the label that is shown in the model tree as well as in the description for the
baffle in the BOM.
Orientation Angle. Specifies the angle position of the baffle.
Base Tube Properties
Type. There are 2 types of steel baffle bases supported by the system: Tube Steel and Square
Steel.
Nominal Size. Specifies the nominal size of the base tube.
Quantity. Specifies the number of base tubes.
Length. Specifies the length of the base tube.
Offset from Bottom Base Plate. Specifies the tube offset from bottom base plate.
Offset from Top Base Plate. Specifies the tube offset from top base plate.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
125
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
126
TECHNOSOFT INC.
AMPreVA 5.0
Identifier. It is the label that is shown in the model tree as well as in the description for the
strainer basket in the BOM.
Start Elevation. Specifies the start elevation of the strainer basket.
Orientation Angle. Specifies the angle position of the strainer basket.
Type. There are three types of strainer basket supported by the system: Style 1, Style 2, and
Style 3.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
127
TECHNOSOFT INC.
AMPreVA 5.0
Basket Properties
Material. Specifies the material of the strainer basket.
Density. Specifies the density of the selected material.
Outer Diameter 1. Specifies the outer diameter of the strainer basket.
Outer Diameter 2. Specifies the outer diameter for the lower section of the strainer basket. Only
available when Type is Style 2.
Height 1. Specifies the height of the strainer basket.
Thickness. Specifies the thickness of the strainer basket.
Base Plate Properties
Material. Specifies the material of the strainer basket base plate.
Density. Specifies the density of the selected material.
Thickness. Specifies the thickness of the strainer basket base plate.
Cover Plate Properties
Center Hole. If selected, the strainer basket cover plate will have a hole.
Material. Specifies the material of the strainer basket cover plate.
Density. Specifies the density of the selected material.
Outer Diameter. Specifies the outer diameter of the strainer basket cover plate.
Thickness. Specifies the thickness of the strainer basket cover plate.
Bolt Holes. If selected, the strainer basket cover plate will have bolt holes.
Quantity. Specifies the number of holes for the strainer basket cover plate.
Diameter. Specifies the diameter of the holes for the strainer basket cover plate.
Bolt Circle. Specifies the bolt circle of the holes for the strainer basket cover plate.
Staggered Holes Properties
Diameter. Specifies the diameter of the staggered holes for the strainer basket.
Center to Center Distance. Specifies the distance between the staggered holes from center to
center.
Holes at Base Plate. If selected, it will indicate the strainer basket base plate will include
staggered holes.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
128
TECHNOSOFT INC.
AMPreVA 5.0
4.8 Access
When the access button is selected the second row of the toolbar will update to show the various
components available for adding. Once a button is selected from the second row, a component
should be selected from the canvas to attach to. The tabs in the work area are updated to provide
setting the features and properties of component being added.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
129
TECHNOSOFT INC.
AMPreVA 5.0
Drawing Mark. It is the label that is shown in the model tree as well as in the description for the
manway in the BOM and the drawings.
Service. Description of the manway service.
Remarks. Comments about the manway.
Material. Specifies the material of the manway.
Pipe. If selected, the nozzle pipe will be considered a seamless pipe. If not selected, the pipe
will be considered as a rolled plate.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
130
TECHNOSOFT INC.
AMPreVA 5.0
Manway. If selected, the nozzle will be considered as manway. If not selected, it will be
considered as nozzle.
Attachment Type. There are 2 types of attachment types for the manway supported by the
system: Stick Thru and Set On.
NPS & SCH. Specifies the nominal pipe size and the schedule of the manway.
Outer Diameter. The outer diameter of the manway.
Inner Diameter. The inner diameter of the nozzle pipe.
Thickness. Specifies the thickness of the manway.
Orientation. For manways in head, there are 3 types of orientation: Radial, Perpendicular and
Hillside. For manways in Shell, there are 2 types of orientation: Radial, and Offset.
Orientation Angle. Specifies the angle position of the manway.
Start Elevation. Specifies the start elevation of the manway.
Offset. Specifies the manway offset from cylinder center line. Only available when Orientation
Offset is selected.
Pad. If selected, the manway will include a reinforcing pad.
Projection Distance Mode. There are two ways to specify the manway projection: Radial
Projection and Outside Projection. Only available for nozzles in Shell.
Radial Projection Distance. Specifies the manway radial distance from tank center.
Outside Projection Distance. Specifies the manway outside length from Attach to Component
outer diameter.
Inside Projection Distance. Specifies the manway inside length from Attach to Component inner
diameter.
Root Opening Clearance. Specifies the root opening of the manway.
Minimum Trim Flush Radius. Specifies the minimum radius to trim the manway.
Cut Nozzle to Attached Object Curvature. If selected, the manway will be cut following the
Attach to Component curvature. If not selected, the manway will have a straight cut.
4.8.1.2 Pad Tab
See Nozzles Pad Tab.
4.8.1.3 Bevel Tab
See Bevel Common Tab specifications as in Figure 17.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
131
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
132
TECHNOSOFT INC.
AMPreVA 5.0
Pipe Schedule. The hinge pipe schedule. Only available when Hinge Type Wing.
Special Pipe Thickness. The hinge pipe special thickness. Only available when Hinge Type
Wing.
Center Pipe to Edge Pipes Gap. The gap distance from the center pipe. Only available when
Hinge Type Wing.
Length. Specifies the length of the hinge. Only available when either Hinge Type Hinge or
Davit.
Height. Specifies the height of the hinge. Only available when either Hinge Type Hinge or
Davit.
Pipe Thickness. Specifies the pipe thickness of the hinge. Only available when either Hinge
Type Hinge or Davit.
Pipe Diameter. The diameter of the hinge pipe. Only available when Hinge Type Hinge.
Pipe Root Opening. The root opening for the davit pipe of the manway.
Gasket Properties
Material. Specifies the material of the manway gasket.
Thickness. Specifies the thickness of the manway gasket.
Outer Diameter. Specifies the outer diameter of the gasket.
Inner Diameter. Specifies the inner diameter of the gasket.
Bolts Properties
Two Holes Natural. If selected, avoids having holes in the flange vertical/horizontal reference
lines.
Double Nut. If selected, the bolting type will consist in a stud and two nuts, if not selected, the
bolting will consist in one bolt and one nut.
Material. Specifies the material of the manway bolt.
Circle Diameter. Specifies the bolt circle diameter of the manway.
Diameter. The diameter of the manway bolt.
Length. Specifies the length of the manway bolt.
Nut Length. Specifies the length of the manway nut.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
133
TECHNOSOFT INC.
AMPreVA 5.0
Rod Properties
Rod. When selected, Manway cover will have rod(s).
Diameter. The diameter of the rod.
Height. Specifies the height of the rod.
Length. Specifies the length of the rod.
Corner Radius. Specifies the corner radius of the rod.
Hanger Info. Specifies the position and angle information of the rod.
Lug Properties
Lug. When selected Manway cover will have a lug plate.
Thickness. Specifies the thickness of the lug.
Width. Specifies the width of the lug.
Height. Specifies the height of the lug.
Corner Radius. Specifies the corner radius of the lug.
Hole Center Elevation. Specifies the elevation of the lug hole at center line.
Hole Diameter. The diameter of the lug hole.
Position Info. Specifies the angle position of the lug.
Socket Properties
Material. Specifies the material of the socket plate.
Height. Specifies the height of the socket plate.
Width. Specifies the width socket plate.
Length. Specifies the length of the socket plate.
Thickness. Specifies the thickness of the socket plate.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
134
TECHNOSOFT INC.
AMPreVA 5.0
Offset from Center. Specifies the socket plate offset. Only available when Davit Type Bend
Corner with Hole is selected.
Hole Root Opening. The root opening for the socket hole.
Washer Properties (only available when Davit Type Wing)
Material. Specifies the material of the washer.
Outer Diameter. The outer diameter of the washer.
Thickness. Specifies the thickness of the washer.
Offset from Round Bar. Specifies the washer offset from the round bar.
4.8.1.6 Davit Arm Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
135
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
136
TECHNOSOFT INC.
AMPreVA 5.0
Angle Extra Height. Specifies the extra height of the angle. Only available when either Davit
Type Bend Corner with Hole or Bend Corner with Pad is selected.
Davit Angle Pad Thickness. Specifies the pad thickness of the davit angle. Only available when
Davit Type Bend Corner with Pad is selected.
Davit Angle Cut Height. Specifies the cut height of the davit angle. Only available when Davit
Type Bend Corner with Hole is selected.
Distance from Corner. Specifies the brace bar distance from corner. Only available when either
Davit Type Bend Corner or Square Corner is selected, and Brace Bar is selected.
Brace Bar Thickness. Specifies the thickness of the brace bar. Only available when either Davit
Type Bend Corner or Square Corner is selected, and Brace Bar is selected.
Pipe Schedule. Specifies the pipe schedule.
Shackle Nominal Size. Specifies the nominal size of the shackle. Only available when either
Davit Type Bend Corner or Square Corner is selected.
Eye-Bolt Nominal Size. Specifies the nominal size of the eye bolt.
Cap Plate Thickness. Specifies the thickness of the cap plate. Only available when either Davit
Type Bend Corner or Square Corner is selected.
Grease Fitting Nominal Size. Specifies the nominal size of the grease fitting. Only available
when either Davit Type Bend Corner or Square Corner is selected.
Stop Plate Type. Specifies the stop plate type, either Plate or Pipe Cap. Only available when
either Davit Type Bend Corner or Square Corner is selected.
Stop Plate Outer Diameter. The stop plate outer diameter. Only available when Stop Plate Type
of Plate is selected.
Stop Pipe Cap Thickness. Specifies the thickness of the stop pipe cap. Only available when
Stop Plate Type Pipe Cap is selected.
Stop Plate Washer Material. Specifies the material of the stop plate washer. Only available
when either Davit Type Bend Corner, Square Corner or Bend Corner with Pad is selected.
4.8.1.7 Weld and Edge Preparation Tab
See Nozzle Weld and Edge Preparation Tab.
4.8.1.8 Conditions Tab
See Conditions Common Tab specifications as in Figure 21.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
137
TECHNOSOFT INC.
AMPreVA 5.0
4.8.2 +Access
Access can be added to Skirts, Transition Shells, Cylinders, and Heads. Various Access styles
are shown in thru.
4.8.2.1 Design Tab
Drawing Mark. It is the label that is shown in the model tree as well as in the description for the
access in the BOM and the drawings.
Description. Description of the cone access service.
Orientation. There are 3 types of orientation: Radial, Perpendicular and Hillside. Availability
depends on the component where the access is attached to.
Position Angle. Specifies the angle position of the access.
Radial Distance. Specifies the radial distance of the access. Only available for access in heads.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
138
TECHNOSOFT INC.
AMPreVA 5.0
Select Nozzle for Start Elevation. Button action that allow the selection of a nozzle to calculate
automatically the elevation for the access. It is also a type in entry to specify a particular
elevation. Not available for access on heads.
Offset. Specifies the access offset from center line. Only available when Orientation Offset is
selected.
Tipping Angle Horizontal. Specifies a horizontal inclination angle for the access.
Tipping Angle Vertical. Specifies a vertical inclination angle for the access.
Root Opening. Specifies the root opening of the access. Not available when Plate Around Hole
is not selected.
Straight Height. Specifies the straight height of the access. Not available when Circular Access
is selected.
Width. Specifies the width of the access. Not available when Circular Access is selected.
Upper Radius. Specifies the upper radius of the access. Not available when Circular Access is
selected.
Lower Radius. Specifies the lower radius of the access. Not available when Circular Access is
selected.
Thickness. Specifies the thickness of the access. Only available when Plate Around is selected
and Circular Access is not selected.
Outside Projection Distance. Specifies the outside projection of the access. Only available
when Plate Around Hole is selected.
Inside Projection Distance. Specifies the inside projection of the access. Only available when
Plate Around Hole is selected.
Material. Specifies the material of the access.
Density. Specifies the density for the selected material.
Plate Around. If selected, the access will have plates. If not, the access will not include plates.
Circular Access. If selected, the access will be a circle.
Pipe. When Plate Around is selected and Pipe is selected, the access plate will be considered a
seamless pipe. If not selected, the access will be considered as a rolled plate. When Plate
Around is not selected the access dimensions can be specified as a pipe. Only available when
Circular Access is selected.
Nominal Size. Specifies the access nominal size. Only available when Pipe is selected.
Special Outer Diameter. Specifies the access special outer diameter. Only available when Pipe
is selected.
Schedule. Specifies the access plate schedule. Only available when Pipe and Plate Around are
selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
139
TECHNOSOFT INC.
AMPreVA 5.0
Special Thickness. Specifies the access special thickness. Only available when Pipe and Plate
Around are selected.
Outer Diameter. The outer diameter of the access. Valid only when Plate Around is selected.
Nominal Thickness. The thickness of the access. Valid only when Plate Around is selected.
Pad. If selected an external pad will be added. Only available when Plate Around and Circular
Access are selected.
Material. Specifies the material of the access external pad. Only available when Pad is selected.
Density. Specifies the density for the selected material. Only available when Pad is selected.
Width. Specifies the width of the access external pad. Only available when Pad is selected.
Thickness. Specifies the thickness of the access external pad. Only available when Pad is
selected.
Root Opening. Specifies the opening of the access external pad. Only available when Pad is
selected.
Fine Grain. If selected, specifies an external pad material fine grain. Only available when Pad
is selected.
Impact Tested. If selected, the external pad will be impact tested. Only available when Pad is
selected.
Normalized. If selected, the external pad will be normalized. Only available when Pad is
selected.
Internal Pad. If selected an internal pad will be added. Only available when Plate Around and
Circular Access are selected.
Material. Specifies the material of the access internal pad. Only available when Internal Pad is
selected.
Density. Specifies the density for the selected material. Only available when Internal Pad is
selected.
Width. Specifies the width of the access internal pad. Only available when Internal Pad is
selected.
Thickness. Specifies the thickness of the access internal pad. Only available when Internal Pad
is selected.
Root Opening. Specifies the opening of the access internal pad. Only available when Internal
Pad is selected.
Fine Grain. If selected, specifies an internal pad material fine grain. Only available when
Internal Pad is selected.
Impact Tested. If selected, the internal pad will be impact tested. Only available when Internal
Pad is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
140
TECHNOSOFT INC.
AMPreVA 5.0
Normalized. If selected, the internal pad will be normalized. Only available when Internal Pad
is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
141
TECHNOSOFT INC.
AMPreVA 5.0
External Weld
Type. There are several attachment types for access.
Upper Groove Weld Pad. Specifies the groove weld for the external pad to the Attach to
Component. Only applies when Pad is selected.
Lower Groove Weld Shell. Specifies the groove weld for Attach to Component to the access.
Inner Fillet Weld A41. Specifies the outside fillet weld for access to the Attach to Component, it
could be the external pad. Only applies when Pad is selected.
Outer Fillet Weld A42. Specifies the fillet weld for the external pad to the Attach to Component.
Only applies when Pad is selected.
Lower Fillet Weld A43. Specifies the inside fillet weld for access to the Attach to Component.
Internal Weld
Type. There are several attachment types for access. Only available when Internal Pad is
selected.
Upper Groove Weld Pad. Specifies the groove weld for the internal pad to the Attach to
Component. Only available when Internal Pad is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
142
TECHNOSOFT INC.
AMPreVA 5.0
Inner Fillet Weld A41. Specifies the outside fillet weld for the internal pad to the Attach to
Component. Only available when Internal Pad is selected.
Outer Fillet Weld A42. Specifies the fillet weld for the internal pad to the Attach to Component.
Only available when Internal Pad is selected.
Weld Ext. Preparation Types. Action button to display the available weld preparations for
external pad.
Weld Int. Preparation Types. Action button to display the available weld preparation for internal
pad.
4.8.3 +Elliptical Ring
4.8.3.1 Design Tab
Drawing Mark. It is the label that is shown in the model tree as well as in the description for the
elliptical ring in the BOM and the drawings.
Service. Specifies the service of the elliptical ring.
Remarks. Specifies some comments about the elliptical ring.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
143
TECHNOSOFT INC.
AMPreVA 5.0
Inside Projection Distance. Specifies the elliptical ring inside length from Attach to Component
inner diameter.
Root Opening Clearance. Specifies the root opening of the elliptical ring.
Cut Ring to Attached Object Curvature. If selected, the elliptical ring will be cut following the
Attach to Component curvature. If not selected, the elliptical ring will have a straight cut. Only
available when Inside Projection Distance is zero.
Copy Parameters. Action button that allows the selection of other elliptical ring to take the
dimensions from.
Bolting Plate. If selected, the elliptical ring will include a bolting plate and cover plate.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
144
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
145
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
146
TECHNOSOFT INC.
AMPreVA 5.0
Once a button is selected the component is added and the work area in the menu is updated to
enable editing and detailing the component features and properties.
The available components to add are:
Ladder
+Cage
Radial Platform
This section describes the various properties than can be edited from the menus that can also be
invoked from the model tree by editing the appropriate component. Each component may have
various properties but only a subset is provided to be modified by the end user in the menu.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
147
TECHNOSOFT INC.
AMPreVA 5.0
4.9.1 Ladder
4.9.1.1 Ladder Tab
Identifier. It is the label that is shown in the model tree for the ladder.
Position Angle. Specifies the angle location for the ladder.
Mounting Surface Radius. The ladder mounting surface radius. The action button allows
selecting a cylinder already drawn in the canvas to take it outer radius.
Mounting Surface Clearance. The mounting surface OD to rung center distance along clip.
Ladder Width. Specifies the width of the ladder from the inner face of both stringers.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
148
TECHNOSOFT INC.
AMPreVA 5.0
Start Elevation. Specifies the start elevation from datum till the center of the first ladders rung.
End Elevation. Specifies the end elevation from datum till the center of the last ladders rung.
Stringer Plates Properties
Bottom Extension. Specifies the extension distance from the center of the first ladders rung till
the bottom edge of the stringer.
Top Extension. Specifies the extension distance from the center of the last ladders rung till the
top edge of the stringer.
Width. Specifies the width of the stringer.
Thickness. Specifies the thickness of the stringer.
Material. Specifies the material of the stringer.
Rung Bar Properties
Rung Bar at Start Elevation. If selected, a rung bar will exist at the indicated Start Elevation.
Rung Bar at End Elevation. If selected, a rung bar will exist at the indicated End Elevation.
Top Rung Center at End Elevation. If selected, the last rung bar will be centered at the indicated
End Elevation; if not selected, the last rung will be aligned in the outer line with the End
Elevation. Available only when Rung Bar at End Elevation is selected.
Rung Bar Min Spacing. Specifies the minimum space between rungs.
Rung Bar Diameter. Specifies the diameter or the rungs.
Mounting Hole Radial Clearance. Specifies the clearance for the rung in the stringer.
Insertion Distance. Specifies the distance of the rung that is inserted inside the stringer.
Material. Specifies the material of the rung.
Exit at Top Front. If selected, the ladder will have an extra length that will allow to exit from the
ladder towards the front.
Exit Extension. Specifies the length of the extension. Only available when Exit at Top Front is
selected.
Ladder Exit Width. Specifies the opening of the extension. Only available when Exit at Top
Front is selected.
Exit Transition Angle. Specifies the angle for the transition between the stringer and the
extension. Only available when Exit at Top Front is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
149
TECHNOSOFT INC.
AMPreVA 5.0
Clip Properties
Type. Specifies the type of clip.
Position. Specifies the position of the clip, either inside or outside of the stringer.
Width. Specifies the width of the clip.
Thickness. Specifies the thickness of the clip.
Material. Specifies the material of the clip.
Clip Clearance from Stringer Edge. Specifies the distance to the clip from the stringers edge.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
150
TECHNOSOFT INC.
AMPreVA 5.0
Ladder Clip Offset from Shell. Specifies the distance from the ladder clip to the shell.
Ladder Clip to Vessel Clip Overlap. Specifies the overlapping distance between the ladder clip
and the vessel clip.
Rung Bars Before First Clip. Specifies the number of rungs before the first clip.
Rung Bars After Last Clip. Specifies the number of rungs after the last clip.
Rung Bars Between Clips. Specifies the number of rungs between two clips.
Bolt Size. Specifies the size of the bolt.
Bolt to Clip Distance. Specifies the distance from the clip edge to the center of the bolt.
Bolt to Bolt Distance. Specifies the distance between to bolts.
Pads Properties
Pads. If selected, the ladder will have reinforcing pads between the clips and the vessel.
Material. Specifies the material of the pad. Only available when Pads is selected.
Length. Specifies the length of the pad. Only available when Pads is selected.
Width. Specifies the width of the pad. Only available when Pads is selected.
Corner Radius. Specifies the corner radius of the pad. Only available when Pads is selected.
Thickness. Specifies the thickness of the pad. Only available when Pads is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
151
TECHNOSOFT INC.
AMPreVA 5.0
Type. Specifies the type of support. If None is selected, no support will be added; if Angle is
selected it will exist a support of type angle.
Material. Specifies the material of the support angle.
Angle Height. Specifies the height of the support angle.
Base Length. Specifies the length of the support angle.
Thickness. Specifies the thickness of the support angle.
Distance from Stringer. Specifies the distance from the stringers edge to the supports edge.
Holes Diameter. Specifies the diameter of the holes.
Upper Hole Distance from Edge. Specifies the distance from the angles top edge to the center
of the highest hole.
Lower Hole Distance from Edge. Specifies the distance from the angles outer edge to the center
of the lowest hole
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
152
TECHNOSOFT INC.
AMPreVA 5.0
4.9.2 +Cage
4.9.2.1 Cage Tab
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
153
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
154
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
155
TECHNOSOFT INC.
AMPreVA 5.0
Angle Clockwise. If selected, platform orientation will be applied following the hands of a clock
rotate. If not selected, platform orientation will be applied counterclockwise.
Identifier. It is the label that is shown in the model tree for the platform.
Start Cage. Specifies the cage at the start side of the platform.
Top of Grating. Specifies the top grating for the platform.
Start Angle. The start angle of the platform.
Offset at Start Angle. The offset at the start side of the platform.
Rolled Plates Dist from Mounting Surf. The distance of the rolled plates from the mounting
surface.
Platform Width. Specifies the width of the platform.
End Cage. The end angle of the platform.
Radial Distance. The radial mounting distance for the platform.
End Angle. The end angle of the platform.
Offset at End Angle. The offset at the end side of the platform.
Gap from Rolled Plates to Deck. The space between the rolled plates and the deck.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
156
TECHNOSOFT INC.
AMPreVA 5.0
Deck Type. There are 2 types of deck supported in the system: Grating and Checkered.
Checkered Plate Gauge. The plate gauge. Only available when Deck Type Checkered.
Grating Size. The size of the grating. Only available when Deck Type Grating.
Vertical Bars Spacing. The spacing between vertical bars. Only available when Deck Type
Grating.
Horizontal Bars Spacing. The spacing between horizontal bars. Only available when Deck Type
Grating.
Radial Angles Properties
Start Radial Angle Size. The angle beam size for the platform at start side.
External Rolled Type. There are 2 types for the external rolled plates in the system: Angle, and
Plates.
Size. The size of the external rolled angle. Only available when External Rolled Type Angle.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
157
TECHNOSOFT INC.
AMPreVA 5.0
Internal Rolled Type. There are 2 types for the internal rolled plates in the system: Angle, and
Plates. Only available when External Rolled Type Angle.
Size. The size of the external rolled angle. Only available when Internal Rolled Type Angle.
Only available when External Rolled Type Angle.
Thickness. The thickness of the external rolled plate. Only available when External Rolled Type
Plates.
Height. The height of the external rolled plate. Only available when External Rolled Type
Plates.
Depth. The depth of the external rolled plate. Only available when External Rolled Type Plates.
4.9.3.3 Posts and Handrails Tab
Posts and Handrails Type. There are 2 types of posts and handrails supported in the system:
Angle, and Pipe.
Top Handrail Elevation. The elevation for the top handrails.
Posts Distance from Top Handrail. The distance between posts and top handrails.
Middle Handrail Elevation. The elevation for the middle handrails.
Posts Spacing (Straight Distance). The straight spacing for the posts.
Posts Spacing (Start and End Sides). The spacing between posts at the start and end sides of the
platform.
Bolt Holes Info. The bolt holes data for the platform handrails.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
158
TECHNOSOFT INC.
AMPreVA 5.0
Post Size. The posts size. Only available when Posts and Handrails Type Angle.
Material. Specifies the material of the posts.
Handrail Size. The handrails size. Only available when Posts and Handrails Type Angle.
Material. Specifies the material of the handrails.
Posts Nominal Size. The nominal size for the posts. Only available when Posts and Handrails
Type Angle.
Posts Schedule. The schedule for the posts. Only available when Posts and Handrails Type
Angle.
Handrail Nominal Size. The nominal size for the handrails. Only available when Posts and
Handrails Type Angle.
Handrail Schedule. The schedule for the handrails. Only available when Posts and Handrails
Type Angle.
4.9.3.4 Supports Tab
Support Type. There are 2 types of platform supports in the system: Bent and With Arm.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
159
TECHNOSOFT INC.
AMPreVA 5.0
Pattern Offset Angle a Start. The offset for the first support at the start side of the platform.
Pattern First Member Angle from Baseline. The opening angle for the first support at the start
side of the platform.
Pattern Offset Angle at End. The offset for the last support at the end side of the platform.
Pattern Last Member Angle from Baseline. The opening angle for the last support at the end side
of the platform.
Max Distance Between Supports. The maximum spacing between supports.
Bent Plate Properties
Inner Height. The height at the inner side of the plate.
Outer Height. The height at the outer side of the plate.
Length List. The length arrangement for the support plates.
Depth. The depth for the support plates.
Thickness. The thickness for the support plates.
Offset from Shell OD. The offset for the support plates from the shell OD.
Clip Properties
Length. The length of the platform clip.
Width. The width of the platform clip.
Thickness. The thickness of the platform clip.
Pad Properties
Pad. If selected the platforms clips will include a reinforcing pads.
Length. The length of the clips pad.
Width. The width of the clips pad.
Thickness. The thickness of the clips pad.
Fillet Radius. The fillet radius of the clips pad.
Bolts Pattern Holes Properties
Diameter. The diameter of the bolt holes for the support plates.
Spacing. The spacing between the bolt holes for the support plates.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
160
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
161
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
162
TECHNOSOFT INC.
AMPreVA 5.0
Lower Pads
Width. The width of the arm pad. Only available when Pad is selected.
Height. The height of the arm pad. Only available when Pad is selected.
Thickness. The thickness of the arm pad. Only available when Pad is selected.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
163
TECHNOSOFT INC.
AMPreVA 5.0
5 Generating Drawings
Editing the top level Drawings object will pop a menu that is used to set the drawing general
attributes and organization. Figure 157 illustrates the top level Drawings menu.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
164
TECHNOSOFT INC.
AMPreVA 5.0
The Drawings branch of the model tree includes a set of drawings that are dynamically created at
run time once they are selected from the tree model. Figure 158 illustrates some of the drawings
that are included in the application. To demand a drawing the user should select the appropriate
sub-object from the model tree. All drawing sub-objects have an icon at the start of the name in
the model tree. These drawing are organized under various sub-object with the appropriate titles.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
165
TECHNOSOFT INC.
AMPreVA 5.0
Most drawings are created following common standards and practices as provided by the various
users. Yet AMPreVA provides advanced capacities to manually create additional dimensions,
notes, data within the drawings as shown in Figure 160 and Figure 161.
At the top of the layout editor a toolbar with various buttons is provided. The first 11 buttons are
used for manual creation of additional drawings entities. The button before the last is used to
setup the drawing individual properties, and the last button is used for regenerating the drawing
with the updates created. Selecting the button label SETUP, as highlighted in Figure 159 and
Figure 160 of the toolbar at the top of the drawing layout editor, will provide a menu to set each
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
166
TECHNOSOFT INC.
AMPreVA 5.0
drawing individual attributes as shown Figure 162. Once updated the second button highlighted
in Figure 160 will update the drawing.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
167
TECHNOSOFT INC.
AMPreVA 5.0
At the bottom of the drawing layout, another tool bar is presented to enable the inspecting,
editing, and modifying of the drawing including notes, dimension, viewport position, etc., as
shown in Figure 163.
Left Click
Right Click
No action is defined.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
168
TECHNOSOFT INC.
AMPreVA 5.0
No action is defined.
No action is defined.
No action is defined.
Allows the selection of a drawing entity to get Allows the selection of a drawing
info from it.
object to get info from it.
Calls a pop up menu to select the printer and set No action is defined.
the appropriate attributes to print the drawing.
Allows the selection of the appropriate format for Same as the left click.
saving. PDF, DXF, and DWG are among the
commonly use format. DWG is often used if the
drawing is used for further editing in a CAD
package.
Advanced functionality not to be used by new Advanced functionality not to be
users.
used by new users.
Advanced functionality not to be used by new No action is defined.
users.
Will close the drawing layout.
No action is defined.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
169
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
170
TECHNOSOFT INC.
AMPreVA 5.0
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
171
TECHNOSOFT INC.
AMPreVA 5.0
6 Generating Reports
6.1 Generating a Bill of Material
Editing the top level object Drawings from the model tree will pop up a menu as shown in
Figure 157. In the second column the second button from the bottom is label Display BOM
Report is used to create the complete bill of material (BOM). This BOM can be viewed in any
file browser of in MS Excel as shown in Figure 166. This bill of material will include the listing
of all component needed to purchase or fabricate for the final assembly of the tank. All the
columns are appropriately labeled and each component makes reference to a drawing for details.
Copyrights TechnoSoft Inc. 11180 Reed Hartman Hwy Cincinnati, OH 45242 www.technosoft.com
172