Documentos de Académico
Documentos de Profesional
Documentos de Cultura
Presentado por: Diana Gasca Andres Escrraga Fundicin de Metales Profesor: Dr. Hctor Snchez S. Universidad del Valle
Pattern is a model or the replica of the object to be cast. It is a larger in size as compared to the final casting, because it carries certain allowances due to metallurgical and mechanical reasons for example, shrinkage allowance is the result of metallurgical phenomenon where as machining, draft, distortion, shale, and other allowances are provided on the patterns because of mechanical reasons.
Top center is the clay original, then the two part plaster mold used for casting the lead at above, and wax cast from mold, sprued for better brass casting, not yet cast. 2008-01-12. homepages.waymark.net/mikefirth/tapper688 1b.jpg
Functions of Patterns:
A Pattern prepares a mould cavity for the purpose of making a casting. A Pattern may contain projections known as core prints (corazn) if the casting requires a core and need to be made hollow. Patterns properly made and having finished and smooth surfaces reduce casting defects. Properly constructed patterns minimize overall cost of the casting.
Types of Patterns:
(a) Split pattern (b) Follow-board (c) Match Plate (d) Loose-piece (e) Sweep (f) Skeleton pattern
2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Types of Patterns
Figure 11.3 Types of patterns used in sand casting: (a) solid pattern (b) split pattern (c) match-plate pattern (d) cope and drag pattern
castings
Gating system
6.Gated pattern:
Most metals undergo noticeable volumetric contraction when cooled Three principle stages of shrinkage:
Shrinkage of liquid as it cools from the solidification temperature Solidification shrinkage as the liquid turns into solid Solid metal contraction as the solidified metal cools to room temperature
Figure Dimensional changes experienced by a metal column as the material cools from a superheated liquid to a room-temperature solid. Note the significant shrinkage that occurs upon solidification.
Minuto 1:12. Se observa la contraccin del metal, no hay tolerancia para compensarla, genera porosidad residual.
Volumetric Shrinkage
Dimensional Allowances
Typical
allowances
0.8-1.0% 1.5-2.0% 1.0-1.3% 1.0-1.3% 1.5%
Shrinkage
allowances are incorporated into the pattern using shrink rules Thermal contraction might not be the only factor for determining pattern size Surface finishing operations (machining, etc.) should be taken into consideration
Solidification Shrinkage
Amount
of liquid metal contraction depends on the coefficient of thermal contraction and the amount of superheat As the liquid metal solidifies, the atomic structure normally becomes more efficient and significant amounts of shrinkage can occur Cavities and voids can be prevented by designing the casting to have directional solidification Hot tears can occur when there is significant tensile stress on the surface of the casting material
1.ShrinkageAllowance:
All most all cast metals shrink or contract volumetrically on cooling.
1.Liquid Shrinkage: it refers to the reduction in volume when the metal changes from liquid state to solid state at the solidus temperature.To account for this shrinkage;riser,which feed the liquid metal to the casting,are provided in the mold. 2.Solid Shrinkage: it refers to the reduction in volume caused when metal loses temperature in solid state.To account for this,shrinkage allowance is provided on the patterns.
Almost all cast metals shrink or contract volumetrically after solidification and therefore the pattern to obtain a particular sized casting is made oversize by an amount equal to that of shrinkage or contraction. Different metals shrink at different rates because shrinkage is the property of the cast metal/alloy. The metal shrinkage depends upon: 1. The cast metal or alloy. 2. Solidification temp.of the metal/alloy. 3. Casted dimensions(size). 4. Casting design aspects. 5. Molding conditions(i.e.,mould materials and molding methods employed)
Up to 2 feet 2 feet to 4feet Over 4feet Upto2feet 2feetto6feet over6feet Upto4feet 4feetto6feet over6feet Upto4feet Over4feet
0.125 0.105 0.083 0.251 0.191 0.155 0.155 0.143 0.125 0.173 0.155
CastSteel
Aluminum
Magnesium
2.MachiningAllowance:
A CASTING IS GIVEN AN ALLOWANCE FOR MACHINING, BECAUSE:
Castings get oxidized in the mold and during heat treatment;scales etc.,thus formed need to be removed. ii. It is the intended to remove surface roughness and other imperfections from the castings. iii. It is required to achieve exact casting dimensions. iv. Surface finish is required on the casting.
i.
HOW MUCH EXTRA METAL OR HOW MUCH
i.
Nature of metals. ii. Size and shape of casting. iii. The type of machining operations to be employed for
Allowance(inch)
0.12 0.20 0.25
Castiron
Caststeel
Nonferrous
3.Draft or TaperAllowance:
It is given to all surfaces perpendicular to parting line. Draft allowance is given so that the pattern can be easily removed from the molding material tightly packed around it with out damaging the mould cavity. The amount of taper depends upon:
i.
Shape and size of pattern in the depth direction in contact with the mould cavity. ii. Moulding methods. iii. Mould materials. iv. Draft allowance is imparted on internal as well as external surfaces;of course it is more on internal surfaces.
Core
2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Full-scale model of interior surfaces of part It is inserted into the mold cavity prior to pouring The molten metal flows and solidifies between the mold cavity and the core to form the casting's external and internal surfaces May require supports to hold it in position in the mold cavit during pouring, called chaplets
Figure 11.4 (a) Core held in place in the mold cavity by chaplets, (b) possible chaplet design, (c) casting with internal cavity.
2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Draft
Minor
Figure 11.25 Design change to eliminate the need for using a core: (a) original design, and (b) redesign.
2007 John Wiley & Sons, Inc. M P Groover, Fundamentals of Modern Manufacturing 3/e
Draft Guidelines: In expendable mold casting, draft facilitates removal of pattern from mold Draft = 1 for sand casting In permanent mold casting, purpose is to aid in removal of the part from the mold Draft = 2 to 3 for permanent mold processes Similar tapers should be allowed if solid cores are used
Wood
Fig:taper in design
i.
It is of irregular shape,
ii. All it parts do not shrink uniformly i.e.,some parts shrinks while others are restricted from during so, iii. It is u or v-shape, iv. The arms possess unequal thickness, v. It has long,rangy arms as those of propeller strut for the ship, vi. It is a long flat casting, vii. One portion of the casting cools at a faster rate
5.Shake allowance:
A patter is shaken or rapped by striking the same with a wooden piece from side to side.This is done so that the pattern a little is loosened in the mold cavity and can be easily removed. In turn,therefore,rapping enlarges the mould cavity which results in a bigger sized casting. Hence,a ve allowance is provided on the pattern i.e.,the pattern dimensions are kept smaller in order to compensate the enlargement of mould cavity due to rapping. The magnitude of shake allowance can be reduced by increasing the tapper.
Pattern Layout:
Steps involved: Get the working drawing of the part for which the pattern is to be made. Make two views of the part drawing on a sheet,using a shrink rule. A shrink rule is modified form of an ordinary scale which has already taken care of shrinkage allowance for a particular metal to be cast. Add machining allowances as per the requirements. Depending upon the method of molding, provide the draft allowance.
Pattern Construction:
Study the pattern layout carefully and establish, a. Location of parting surface. b. No.of parts in which the pattern will be made. Using the various hand tools and pattern making machines fabricate the different parts of the pattern. Inspect the pattern as regards the alignment of different portions of the pattern and its dimensional accuracy. Fill wax in all the fillets in order to remove sharp corners. Give a shellac coatings(3 coats) to pattern. impart suitable colors to the pattern for identification purposes and for other informations.
and orientation of the parting line is important to castings Parting line can affect:
Number of cores Method of supporting cores Use of effective and economical gating Weight of the final casting Final dimensional accuracy Ease of molding
Design Considerations
Two-part mold showing the parting line and the incorporation of a draft allowance on vertical surfaces.
Design Considerations
Figure 11-17 (Right) Elimination of a drysand core by a change in part design.
Figure 11-16 (Left) Elimination of a core by changing the location or orientation of the parting plane.
Design Considerations
It
is often desirable to minimize the use of cores Controlling the solidification process is important to producing quality castings Thicker or heavier sections will cool more slowly, so chills should be used
If section thicknesses must change, gradual is better If they are not gradual, stress concentration points can be created
Fillets
Figure 11-18 (Top left) Design where the location of the parting plane is specified by the draft. (Top right) Part with draft unspecified. (Bottom) Various options to produce the topright part, including a no-draft design.
Section Thicknesses
Figure a) The hot spot at section r2 is cause by intersecting sections. B) An interior fillet and exterior radius lead to more uniform thickness and more uniform cooling.
Design Modifications
Hot
spots are areas of the material that cool more slowly than other locations
Function of part geometry Localized shrinkage may occur
Design Modifications
Parts
An
Thin-walled
Design Modifications
References
Rao, P.N. (2003). Manufacturing Technology. New Delhi: Tata McGraw-Hill. Pattern Allowances in casting, Vikrant Sharma, MITS Lakshmangarh 2008 Foundry technology. Peter Beeley, 2th edition, Reed Elsevier, 2001